Search Documents

By D Curry, M F. Young

æConventional wisdomÆ believes that fine particles have low flotation recoveries. Plant size û recovery graphs often have the classic æhillÆ shape û high recovery in the mid sizes and low recovery at the fine and coarse ends. Yet if mineral liberation is poor, low fines recovery may be because you don't grind fine enough! This apparent paradox is explained by the old concept of æsand/slimesÆ circuits, which recognises the different flotation needs of fine and coarse particles. This concept is overlooked in the push for simpler circuits and larger equipment. Most plants now treat all particles together in a wide size-distribution. Reagent conditions are set for the dominant coarser particles, so fines are starved of collector. Worse still if there are significant midsized composites û often these have to be rejected in cleaning to achieve target concentrate grade. But the conditions which reject mid-size composites û collector starvation and high depressants û also reject fine liberated particles. In fact, fines flotation can be excellent when flotation chemistry is tailored to fines.

Jan 1, 2004

By Charles D. Litton

Introduction The successful performance of a mine-wide fire detection system depends upon its ability to detect the presence of a fire rapidly and reliably. It should be sufficiently rapid so that there remains enough time to either safely evacuate a mine or successfully extinguish and control the fire or both. It should be reliable so that false alarms are minimized without sacrificing sensitivity or time response. Systems should also be durable enough to withstand the mine environment over long periods of time while maintaining a high degree of re1iability. Maintenance and calibration of the system should be simp1 e and not require the expenditure of excessive time and manpower to keep it operational. Sensitivity, reliability, and durability of mine fire sensors and their electronic support systems have been the subject of significant Bureau research within recent years. The bulk of this type of information, along with the reports from which the remainder of this paper is derived, can be found in the Bibliography. It suffices to say that there exist commercially available systems for use in mines. This paper addresses a strategy for the use of such sensors and systems. Many factors influence the design of a mine-wide fire detection system, such as the potential sources and modes of ignition, the types of combustibles involved and the quantities avai1able for fire growth and flame spread. Mine air ventilation influences the growth and spread of a fire and also serves to transport the products-of-combustion to other areas of a mine remote from the fire. Fire sensor alarm thresholds place limits on the sizes of fires that can be detected. The time to respond to a detected fire, either in terms of evacuation or control and extinguishment, place additional time constraints on the design of fire detection systems. These factors interact with each other, often in complex ways, and it is the definition and understanding of these factors and their interactions that hold the key to the design of adequate and re1iable fire detection systems. Our level of understanding of the problem has increased dramatically within recent years and it is the intent of this paper to discuss the progress that has been made and how the information can best be used to improve the level of fire detection in underground mines.

Jan 1, 1986

By H. Perez, A. Lavoie, V. Prévost, P. Létourneau, P. Lind

The Home smelter is a custom copper smelter located in Rouyn-Noranda, Quebec. In 2005, the smelter produced 145,000 t of copper containing 807,000 oz of gold, 20,388,000 oz of silver in addition to 515,000 t of sulphuric acid. Recently, a flexible flow sheet has been developed incorporating the intermittent use of the Noranda Continuous Converter allowing for the increasing or decreasing of production based on market conditions, while attaining 90% or greater sulphur fixation regardless of operating mode. For 2006, the smelter is operating in full production mode and production is expected to be approximately 185,000 tm of copper. Mechanical modifications, process changes, metallurgical concepts, minor element treatments, and operational techniques that have allowed the smelter to develop this flexibility are presented. Current efforts to increase the productivity of the converter aisle and anode furnaces as well as improvements being made to address fugitive emissions are also discussed.

Jan 1, 2007

By R. Grau

"After commissioning and start-up of the first 500m3 TankCell® flotation cell in 2014, the over 300m3 mechanical flotation cells have earned their place in large-scale flotation operations. These 500 to 630m3 cells, designed for projects with large throughputs, are proven to provide savings in project capital and operational expenditure through savings in foot print, energy consumption, and less equipment to install and maintain. Addition to savings in different phases of a project, these cells provides operational flexibility and has shown improvements in metallurgical performance. In this paper a case study from Kevitsa TankCell® e500 installation and Buenavista del Cobre TankCell® e630 installations will be given.INTRODUCTION After development (Grönstrand and Bourke, 2008), characterization (Morales et al. 2009; Yanez et al. 2009; Grönstrand at al. 2009), validation (Elgueta et al. 2009; Coleman and Dixon, 2010), and more than 350 industrial installations of the Outotec TankCell® e300 flotation cell, the well proven energy efficient TankCell® product family introduced the TankCell® e500 forced-air flotation cell late June 2012 (Outotec.com, 2012). The introduction of the 500 m3 flotation cell followed by introduction of a 630 m3 flotation cell, TankCell® e630, in October 2014 (Outotec.com, 2014). These large flotation cells are designed for projects with high throughputs where the number of cells needed for operation with smaller equipment would become large. The benefits of this size of flotation cells comes from the lower capital expenditures due to lower equipment costs, savings in plant footprint, less installation work with less auxiliary equipment, lower energy consumption, and less units per installation resulting in less components, spare parts and maintenance.The first TankCell® e500 was commissioned and taken into operation in October 2014 at FQML Kevitsa Cu-Ni-PGE concentrator, nowadays owned by New Boliden. The first TankCell e630 was taken into operation in January 2018 at GrupoMexico’s Buenavista del Cobre Cu-Mo concentrator. The start-ups of the first TankCell® e500 and TankCell® e630 followed with test work where the hydrodynamic performances of the cells were characterized and metallurgical performance studied. The results of the TankCell® e500 test work were presented in detail by Mattsson et al (2015a; 2015b) and TankCell® e630 by Grau et al. 2018. In this paper the metallurgical improvements achieved with the large cell installations will be presented."

Jan 1, 2019

By M Yvon, S Parkes, K P. Galvin, P Wang

Mineral liberation is critical to maximise the grade and recovery of nickel, however this objective is challenged considerably by the poor flotation kinetics, especially that of ultrafine particles (Kelebek and Tukel, 2018; Multani and Waters, 2019). High recoveries demand long cell residence times and hence a large flotation capital expenditure (Wills and Finch, 2016). However, this leads to excessive entrainment of gangue minerals, thus negating efforts to depress its recovery. This study aimed to investigate new hydrodynamic approaches to improve nickel flotation, focusing primarily on unrecovered nickel from a Western Australian tailings stream. Mechanical cell flotation experiments were conducted to understand the flotation kinetics, covering different size ranges. A novel Reflux Flotation Cell (RFC) was also used to improve the nickel recovery and reject the silicates. Future work aimed at applying the RFC to different size portions is also outlined.

Aug 24, 2022

By D Obeng, D Alexander

Over the past five years, commodity prices have been high and the focus of many plants has been æthe more metal the better, at whatever costÆ. In the recent economic crisis, the focus has shifted more to reducing the cost of production and operating at higher efficiency. Since 2002, JKTech has partnered with the Century mine in north-west Queensland to transfer technology and understanding through the good, bad and ugly economic environments, using methodology and techniques arising from research at the Julius Kruttschnitt Mineral Research Centre (JKMRC) and other research institutions around the world as part of the AMIRA International P9 Project. The JKTech studies were concentrated around the primary zinc circuit. During this period, Century expanded the primary zinc regrind capacity, installed additional scavenging capacity, installed and commissioned a Jameson cell for concentrate cleaning in the carbon preflotation circuit, and installed additional primary grinding capacity. Flotation circuit models were developed for each of the survey campaigns and enabled opportunities for further improvement to be identified, implemented and tested in the subsequent campaign.

Jan 1, 2009

By P Bourke, S Ronkainen

Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technicianÆs job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always other problems to attend to. A considerable amount of work has thus been done to develop a æsystemÆ that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterÖ instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability. Three FrothMasterÖ units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:to control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other; control of the concentrate grade (per cent copper) from the first rougher; reduction in the frother consumption in the rougher circuit by monitoring the froth speed. A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions: Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint. Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time by the OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore. The results from a 21-day trial have shown the following:The ratio of concentrate mass-recovery between two cells in series on the same level has been successfully balanced, thereby overcoming problems due to differences in hydrostatic heads. It is possible to control the speed of the froth, in mm/s, to within five per cent of its setpoint using the aforementioned manipulated variables. It has also been shown that, for reliable control, it is necessary to control more than just one variable (eg level or air). The grade of the first rougher concentrate has been controlled to within 0.3 per cent of the grade setpoint for long periods of time, which has important implications for the circuit recovery. The frother consumption has been reduced significantly. This paper will thus show that substantial progress has been made to demonstrate the value of using on-line froth speed measurements in flotation plant control to obtain real financial benefits.

Jan 1, 2000

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"Cu ore bodies commonly contain oxide Cu at the surface, with sulfide Cu content increasing with depth. The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Current practice of oxide Cu recovery involves sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors. CPS has shown to improve recovery of oxide Cu but has the following limitations: a) HSE issues with NaSH, b) high consumption of NaSH, and c) inability to recover certain oxide Cu minerals because they are refractory to sulfidization. The oxide Cu flotation is further complicated by the presence of certain non-sulfide gangue minerals which adversely impact both recovery and selectivity.Over the past eight decades, numerous collectors have been proposed and evaluated for the direct flotation (i.e. without sulfidization) of oxide Cu minerals, the most researched of which is alkyl hydroxamate. While there are numerous publications dealing with the fundamentals of interaction of alkyl hydroxamates with single minerals, there are few publications which discuss the practical aspects of alkyl hydroxamate use in ore flotation, particularly their use with sulfidizing agents. Case studies in this paper include methods to identify optimum combinations of sulfidizing agents and oxide collectors to maximize recovery for various types of ores. It was observed that some ores do not require any sulfidization, while others require at least partial sulfidization to improve efficacy of AHX. Depending upon the ore type and mineralogy, recovery improvement in the range of 5 to 15% units, over and above that achieved with CPS, has been observed with the use of AHX. For ores requiring high dosages of NaSH, it was shown that AHX can be used to reduce the NaSH consumption significantly. The challenges associated with the presence of non-sulfide gangue minerals in oxide copper ores are included, and the use of modifiers to alleviate the associated problems and enhance the performance of AHX is discussed."

Jan 1, 2016

By J. -C. Sztuke, M. Cao

ABSTRACT Wash water and polyethylene oxide (PEO) were used in the flotation of quartz and coal. Wash water decreased entrainment of –15 µm quartz. The optimum superficial wash water rate was 0.05 cm/s. PEO also lowered entrainment. The combination of wash water and PEO led to a slight further reduction in entrainment. For 1:1 mixtures of –15 µm quartz and –300 µm oxidized coal, the combined use of wash water (0.05 cm/s) and PEO increased the separation efficiency from approximately 30% to > 70%, whereas wash water alone at 0.05 cm/s did not lead to a discernible increase.

Jan 1, 2014

By Keila Gonçalves, Aline Tavares, Danielly Couto

"The sulphide copper deposits from the Carajás area (North region of Brazil) were generated by the percolation of hydrothermal fluids in volcanic and granitic rock and are denominated as IOCG deposits (iron oxide copper-gold deposits). During these hydrothermal events a wide variety of gangue minerals such as amphiboles, biotite and fluorite were formed. These gangue minerals are enriched in fluorine and chlorine which are deleterious elements in the copper concentrate. Chalcopyrite and bornite are the main copper-bearing minerals and they can occur in veins, in brecchia or disseminated in gangue.The study, which included bench scale flotation tests and minipilot plant tests was aimed at improving the fluorine rejection in the flotation process during the flowsheet design for one of these Carajás sulphide copper deposit. All of the study was supported by quantitative mineralogical techniques such as QEMSCAN and the use of a scanning electron microscope (SEM).This paper describes and discusses the results obtained in the metallurgical tests and emphasizes the importance of the quantitative mineralogical characterization during the process conditions optimization and flowsheet design.INTRODUCTIONIron oxide copper-gold (IOCG) deposits encompass a wide spectrum of sulphide-deficient low-Ti magnetite and/or hematite ore bodies of hydrothermal origin and normally have important copper sulphide reserves. In the Carajás mineral province, located at the southeast part of the Amazon Craton in Pará State (Brazil), there is a variety of world-class (>200 million tonnes) Fe-oxide Cu-Au deposits (e.g. Salobo, Cristalino and Sossego), whose genesis has been assigned to hydrothermal fluid percolation in volcanic and granitic rocks. Figure 1 displays the location of the Carajás area.The hydrothermal thermal fluid composition was extremely variable. It may have contained gases, salts (brine) and metals. The metals were carried as various complexes and it is thought to have involved sulphur, chlorine and fluorine containing species. This resulted in some minerals formed during the hydrothermal alteration having high fluorine and chlorine contents. These elements result in smelter penalties in a copper concentrate because they cause the smelter off-gases to be more corrosive."

Jan 1, 2011

By Roger Lucas, Dale Nies

The McLaughlin Mine is an open-pit disseminated gold mining operation. Homestake Mining Company's approach to solving some of the blasting problems inherent to this type of deposit provide an interesting case history. Geology, although unique and site specific, is overall similar to other mines within the Western United States over-thrust belt and demonstrates an excellent example of the blasting conditions and requirements common to most of these operations.

Jan 1, 1990

By Sri Sawmliana, P. Pal Roy

Blasting Gallery (BG) method was introduced in India for higher production and low cost of excavation to substitute conventional hand section and stowing methods for thick coal seam. The Singareni Collieries Company Ltd. (SCCL) adopted this method in the year 1989 and since then successfully operating at GDK-10, GDK-8 & VK-7 Incline mines in Andra Pradesh, a southern state of India. It is also successful at Chora 10 Pit Colliery of Eastern Coalfields Ltd. (ECL) in West Bengal whereas at East Katras Colliery of Bharat Coking Coal Ltd. (BCCL) in Jharkhand State, the method has been partially successful due to some geological constraints of the area.

Jan 1, 2003

By Knijnikov M, Cameron D

Coal Quality management and the control of the flow of coal through complex mining preparation and transport phases of standard mining operations has assumed greater importance over recent years.

Jan 1, 1998

By Steven J. Schatzel, James Addis, K. Vaibhav Raj, Berk Tulu

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to enhance methane control and mine ventilation practices at coal mines, as a method to mitigate hazardous work conditions. NIOSH researchers conducted case studies to investigate the effectiveness of existing systems and improve performance to decrease the potential for unplanned or excessive methane emissions. At one mine, drainage was influenced by hydrofracking inefficiencies where two of the six wells showed good frack development. Methane content was variable, from 300 ft3/t to 600 ft3/t. This paper also summarizes overburden movement during undermining and the estimated quantities of gas transported to the mine using FLAC3D and CFD modeling. The findings from this research effort highlight considerations based on specific mine conditions that may also be applicable to most longwall mines utilizing methane control systems.

Feb 1, 2025

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By Steven Putt

The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

Feb 1, 2020

By M F. Gazley

The amphibolite-facies metabasaltic rocks of the Mine Mafic Package at Plutonic Gold Mine, Marymia Inlier, Western Australia, contain an estimated total endowment of 12.2 Moz of Au, which includes 4.71 Moz of past production and 2.77 Moz of reserves and resources; the remainder comprises lower-grade inventory. Over 65?000 multi-element analyses of whole-rock core and face channel samples from the underground workings of the deposit have been collected by portable X-ray fluorescence (pXRF) using a handheld Innov-X Omega pXRF unit. The analyses were performed on pulverised samples through paper bags, and were corrected using a pulverised, matrix-matched, reference standard. This method of data correction compares favourably with conventional XRF analyses performed on the same samples.A preliminary study based on pXRF analyses from a small number of drill holes found that a geochemical stratigraphy was evident in the pXRF data, and that this stratigraphy strongly controlled the location of Au mineralisation. The present study incorporates a much larger pXRF data set that samples a greater volume of diamond drill core and face channel samples and presents the data in a three-dimensional (3D) framework.This data set allows an investigation of the mineralogy of Au mineralisation with varying geochemical associations across the deposit. Historically, there has been a strong relationship identified between As and Au, which has caused issues with metallurgical performance, rendering some areas of the deposit only marginally economic. Utilising seamless data integration of the pXRF data set allows for recognition of the different styles of Au mineralisation using elemental concentrations and ratios from the multi-element analyses (Au:As, Au:As:Cu, As:Cu vs. K:V), and to visualise the distribution of these different mineralogical associations in 3D. The results of the 3D modelling and geochemical characterisation of the different styles of Au mineralisation are currently the focus of an extensive metallurgical testing program, the preliminary results of which are presented here.

Aug 22, 2011

By M. Balamurali, K. M. Seiler

Modelling stockpiles is a key factor of a project’s economics and operation in mining, because not all the mined ores are not able to mill for many reasons. Furthermore, the financial value of the ore in the stockpile needs to be reflected on the balance sheet. Therefore, automatically tracking the boundaries of the stockpile facilitates the mine scheduling engineers to calculate the tonnage of the ore remaining in the stockpile. This paper suggests how the dynamic of stockpile shape changes caused by dumping and reclaiming operations can be inferred using polygon models. The paper also demonstrates how the geometry of stockpiles can be inferred in the absence of reclaimed bucket information, in which case the reclaim polygons are established using the digger’s global positioning system (GPS) positional data at the time of truck loading. This work further compares two polygon models for creating 2D shapes.

Sep 1, 2021

The Porgera mine and treatment plant are located in the Enga Province of Papua New Guinea. Gold in the Porgera deposit is found free and in association with the primary sulphide mineral pyrite. The refractory nature of the gold in the pyrite r

Jan 1, 1997