Search Documents

By J. G. M. Mukoya, B. Adebayo

"This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90–180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to ‘stall’. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit. IntroductionDrilling and blasting contribute most to the operational cost in opencast mining and have the potential to influence the cost of downstream operations (Aipanda, 2011). The drillability of rocks depends not only on the rock properties, but also on the drilling tools and operational variables. In rotary drilling, rotational speed, thrust, and flushing are the operational variables, and are known as the controllable parameters. Rock properties and geological conditions are the uncontrollable parameters. Although, many attempts have been made to correlate drillability with rock properties, the rock characteristics affecting rotary drilling have not been entirely defined (Hartman, 1962; Kahraman, Bilgin, and Feridunoglu, 2003). The drill bit is forced into a rock surface from the rotary power head, hence creating stresses and cracks at the bit-rock interface. The performance of a particular bit in any formation i"

May 1, 2019

By J. L. Ellenberger

The U.S. Bureau of Mines has cooperated with Cyprus Casa Grande Corporation Cyprus Casa Grande Mine, Cas a Grande, Arizona, since 1988 to assess the hydrology of an in situ leaching test facility. This work has resulted in an in situ design for leaching copper oxide ore that takes advantage of the increased mineral access associated with poor quality rock surrounding mine drifts. Blasting and bulkheads are used to produce readily-leachable rubble and contain and control solution movement, respectively. The design reduces the need for handling solution under high pressures in an injection/recovery system for in situ leaching of underground ore bodies. Early work at the site recognized a stress redistribution zone and increased transmissivity near drifts. Fracture data from a corehole oriented parallel to the dip of the ore body indicated an increase in fracture frequency around drifts a distance of 21 m (70 ft) away from the 5 m (16 ft) diameter drifts.

Jan 1, 1994

By Don Reining

The sand and gravel industry in Southern California has made a sizeable contribution to the construction development of the 15 County area in this part of the State. Facing this mineral extraction industry, in the next decade, is a problem of meeting the market demand. The question is, "how can sand, gravel and rock operations be made compatible with goals for sound and attractive community development?" Three basic principal characteristics of the land needed for this-mining industry are: 1. The land must have workable sand, gravel or stone deposits. 2. The land must be properly located for transportation purposes close to the market in order to sell the aggregate at a minimum cost. 3. The land must be zoned so that it will be permissible to mine.

Jan 1, 1967

By Pinnaduwa H. S. W. Kulatilake

A new formulation is given to conduct a probabilistic block theory analysis. A new computer code (BTAC) has been developed to perform both deterministic and probabilistic block theory analyses. The variability of the discontinuity orientation and shear strength is incorporated in the probabilistic block theory analysis. Discontinuity orientation is treated as a bivariate random variable including the correlation that exists between the dip angle and dip direction. BTAC code was applied to perform both deterministic and probabilistic block theory analyses for a part of an open pit mine in the U.S. Needed geological and geotechnical data for the analyses were obtained from field and laboratory investigations. The variability of the discontinuity orientations resulted in important differences between the probabilistic and deterministic block theory analyses results. The results confirmed that the design value selected for the Maximum Safe Slope Angle (MSSA) for a particular region in the open pit mine based on the deterministic block theory analysis can be on the unsafe side. In summary, the results showed clearly the superiority of probabilistic block theory analysis over the deterministic block theory analysis in obtaining additional important information with respect to designing rock slopes.

Jan 1, 2014

By Burt G. Look, David W. Lacey

"Certification of foundation capacity during the construction phase is often assessed by strength or weathering state descriptors based on visual observations. This case study used the Point Load Index (PLI) test as a quantitative tool in the construction certification of a pile’s design capacity. Construction phase tests were completed on irregular sized rock samples whilst comparable design phase testing was completed on intact rock core samples. Statistical comparisons were made to assess the repeatability between the PLI tests, with best-fit Probability Distribution Functions (PDFs) determined for both datasets. Pronounced differences were observed based on the PDF adopted to characterize the PLI dataset, the consequence of which would be a significant change to the pile’s design capacity. The adoption of the lower quartile value is shown to satisfy both design conservatism and construction simplicity requirements. The commonly held belief that rock samples produced during socket excavation may be biased towards the higher strength portion of the rock mass, is shown to be invalid for this site. As the central bridge piers were certified using Plate Load Tests (PLTs), the resultant load-settlement relationships were compared with the PLI strength assessments made for similar materials recovered from the adjacent abutment piles.INTRODUCTIONThe upgrade of the Foxwell Road Overpass across the Pacific Motorway in South East Queensland required the duplication of an existing four span bridge structure. The foundations of the new bridge included the installation of 1.2m diameter cast in place (bored) piles at the bridge abutments and 900mm diameter cast in place (bored) piles below a retaining wall to be constructed adjacent to the existing abutment.The site geology was dominated by the Palaeozoic Neranleigh–Fernvale Beds, predominantly comprised of argillite, sandstone and greywacke. Limited soil materials existed at the site, with Extremely Weathered (EW) rock typically encountered within metres of the existing ground surface. The exception to the existence of shallow rock were locations where existing filling of the site had occurred – i.e. approach embankments to existing bridge structure.Capacity of pile sockets is typically assessed onsite by descriptive rock strength or weathering assessment. Such descriptors encompass a wide range of values and lack precision. Due to the subjectivity of such assessment techniques – a factor of 3 is often observed in terms of strength assessment based on one’s interpretation of rock strength descriptors alone – uncertainty on site often occurs regardless of whether a lower bound, average or other characteristic design parameter applies."

Jan 1, 1900

By R. J. Cefalo

Blast and mining spillover between phases or critical areas of the pit is a continuing problem in the mining industry and a safety concern for operating mines. The challenge for many mines is to produce the highest value in the shortest amount of time for any project. For any project, the top priority of any mine is producing ore as fast as possible. The next challenge is to keep that ore feed continuous. To achieve continuous ore feed, pits are designed with multiple phases that are connected and are mined at different elevations. This difference in elevation causes dangers with spillover between the phases during mining, drilling, and blasting. This paper covers an incident that occurred at an active mine and the work completed in creating a spillover control program over an active mining phase. The drill and blast technical group was responsible for creating blast patterns to reduce spillover between these phases. Unrealistic goals and expectations were initially set for the area of the pit. The drill and blast technical group needed to figure blast objectives and work with the geotechnical team to align with these goals. This paper will go over the executed example of setting up spillover targets and expectations for multiple sections of an operating mine. Different sections of the pit had different control measures and blast objectives due to narrow laybacks and double benching. The use and value of blast objectives and goals were beneficial in setting expectations and measuring design success. Having unrealistic blast goals can set up the operations to fail or get frustrated in trying to work on an impossible task. The problems and risks of phase interactions for many open pit operations need to be considered in the design process, along with designed controls that minimize the probability of any safety incident. Mine designs are being created in the industry and do not consider phase-to-phase mining interaction and the impact it would have on safety or production. The best future for safer mines is blast patterns that reduce spillover between phases of mining and pit designs that might account for spillover interaction.

Jan 1, 2024

By M. Z. Emad, Y. Majeed, G. Rehman

Massive deposits of rock salt are mined in the Salt Range area of Pakistan. The main export products of rock salt include salt lamps, blocks, and tiles, while local consumption includes the chemical industry and domestic use. The profitable production of salt for value addition depends on the quality, size, and shape of the block. Salt processing for value addition is easier when very few cracks are present in the blocks. The current salt mining practice involves drilling and blasting, which introduces undesired fractures in the material. This paper focuses on the extraction of rock salt blocks by applying conventional cuboidshaped block mining methods used in quarries. The techniques include wedges and feathers, expansion chemicals, and blasting with low-yield explosives. Experimental work involved both laboratory-scale and in-situ field testing. Laboratory experiments assisted with the determination of splitting force, loaddeformation curves, and other rock mechanics parameters. Regression analysis proposes a relationship for the estimation of radial strain from the load in the case of the wedges and feathers method. The splitting force obtained from the laboratory tests was used to confirm the accuracy of the already published empirical relationship. The results of the laboratory as well as in-situ tests showed that the wedges and feathers technique is the most suitable method for mining rock salt blocks of the desired size, shape, while minimizing cracking.

Mar 2, 2022

By J. P. Germiquet

"Rock properties have a material impact on mining processes, including drilling performance. An investigation using point loaded index (PLI) data converted to uniaxial compressive strength (UCS) has revealed that a direct relationship between grain size and UCS exists at Mogalakwena Mine. This correlation is best seen in unaltered rock, with lower correlations for altered rock types. Measurements from the new RockMa system installed on drill rigs can be used to obtain rock strength data to validate the current rock strength domains and create additional data for the next benches below. An investigation of penetration rates in different lithologies shows that rock composition plays an important role in determining drill performance. Additionally, there is an inverse relationship between rock strength and drilling penetration rate – a measure of how efficiently a hole is drilled.The domaining of grain-size-adjusted UCS at Mogalakwena Mine will allow more accurate scheduling of drill rigs through increased knowledge of rock strength in various areas. Successful rock strength domaining has the potential to be incorporated into blast indexing and predicting crushing/milling performance.IntroductionThe optimization of mining and processing through geometallurgical characterization of ore are key drivers of value realization (Deutch, 2013). Rock strength is one such property and is affected by, among other variables, composition, texture, and grain size (Ozturk, Nasuf, and Kahraman, 2014). Mogalakwena Mine is exploiting the intrusive Platreef PGE (platinum group element)-bearing orebody which forms part of the northern limb of the Bushveld Complex. This complex orebody exhibits areas of metasomatic alteration, metamorphism, and sporadic mineralization of the footwall and hangingwall (Nex et al., 2006). Understanding this variability is paramount due to the implications for rock strength and hardness, which in turn affect crushing, milling, and liberation efficiency. These variables must be known prior to blasting in order to optimize mine and plant processes using in-situ variables. This necessitates predictive modelling (Deutch, 2013). Geological and geotechnical data was sourced from the Overysel (OY) exploration database for the study. Point load testing was done for each borehole and the results converted to uniaxial compressive strength (UCS) (Akram and Bakar, 2007). The relationship of lithology, texture, and grain size with UCS revealed an inverse relationship between grain size and UCS in unaltered rock. The relationship was not present in altered rock types. A comparison of mean strength and hardness results indicated that Bond work index and UCS may be related. Drilling performance is affected by UCS (Bourgoyne et al., 1986), and this was proven using recent measurements obtained during drilling. Lastly, grain-sizeadjusted UCS values were applied to a 3D model for the OY property."

Jan 1, 2016

By M Sandy, A Vakili, J Albrecht

Although rock strength anisotropy is a well-known phenomenon in rock mechanics, its impact on geotechnical design is often ignored. No widely accepted guideline currently exists for its characterisation. Anisotropy can significantly control the failure mechanism and progression of damage into the rock mass, particularly in high-stress conditions. As such, it can play a key role in the stability of underground excavations and subsequent geotechnical design.This paper introduces the concept of anisotropy at both intact and rock mass scales. It then presents guidelines for measuring anisotropy and assigning rock mass strength properties. An improved unified constitutive model (IUCM), which can account for more complex failure mechanisms, is then briefly described. This IUCM is used to better understand the typical responses of anisotropic rocks to underground mining and to develop an improved damage classification scheme for these conditions.The application of conventional design methods in anisotropic conditions is shown to lead to significant errors. Two case histories are then presented, illustrating how the proposed methodology can improve the reliability and accuracy of the geotechnical analysis when compared with conventional design methods.CITATION:Vakili, A, Albrecht, J and Sandy, M, 2014. Rock strength anisotropy and its importance in underground geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 167–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By K. Ogawa, T. Yokoyama

Hydraulic fracturing technique, an applied technique to cause tensile fractures to rock by injecting water pressure to a certain closed section of the borehole, is a measurement method of in-situ rock stress. This technique has the highest track record for techniques used in sub 1000 meter. A feature of this technique is comparatively simple and easy for in-situ stress measurement, because the measurement is applicable when a drilled borehole is available. The predominant advantage of this method is that elastic constants such as Young’s modulus and Poisson’s ratio are not required for determining the value and direction of initial stress. The factors to determine the stress state are the water pressures of re-opening and shut-in of fractures around the borehole wall and its directions. With conventional methods, however, the accuracy of the derived stress states from the observation equations was often adversely affected by the lack of consideration of the remaining water pressure in fractures and insufficient stiffness of the pressurization system. We have developed a new hydraulic fracturing system based on a new test method concept overcoming these defects, and applied to a 300 meter deep borehole in granite. The most important improvement of the new system is an employment of a syringe pump which enables an accurate flow control of fluid with less than 1ml/min in the pressure of 30MPa. Therefore the new test system has a quick response for pressurising in the interval zone, and the measured data was confirmed extremely accurate.

Jan 1, 2015

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

By K Morrison

Different individuals have calculated the boundary stresses around elliptical openings in an infinite elastic medium for various conditions of loading. With caution, such calculations are useful in indicating stress trends in mining. This paper illustrates an application to caving operations and suggests that abnormal field stress would have an adverse effect. Introduction GELDART and Udd (1), applying elastic theory, confirmed, and set out graphically, the stress distributions on the surface of elliptical openings with axis ratios varying from 1.0 (a circle) to infinity (a crack). The loading conditions varied from uniaxial to hydrostatic, and inclinations for the opening, with respect to the stress axis, varied from 0° to 90°. As most mine openings can be generalized into this elliptical conception, the usefulness of the presentation lies in the fact that given reasonable estimates for the stress ratio, the axis ratio, and its inclination, then the trend in stress concentrations as an opening develops can be readily approximated.

Jan 1, 1964

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964

By Ralph H. Cleland

Introduction The mines of northern Ontario have entered the class of deep mines. It has often been asked: How deep can operations be carried on? What will the temperature be? This paper is a résumé of a brief survey of rock temperatures made by the Ontario Department of Mines during the year 1932. Present temperatures were recorded and the geothermal gradients that now exist were determined. No alarming situations were found, but many interesting ones have been noted. Northern Ontario mines are fortunately situated as compared with most deep-level mines of the world. The mean yearly temperature, as determined from meteorological records of the Federal Department of Marine, is from 33 to 38 degrees Fahrenheit. The tables on the next page show the temperature range in and about our mining camps ( l ). As no exact figures were obtainable for Kirkland Lake, the data for Iroquois Falls, which is about 50 miles northwest, were taken as applicable there. The figures for Timmins were checked against those of Cochrane and Iroquois Falls and found to be very similar, so that the Cochrane data may be used for the Porcupine camp. The yearly mean temperature is considered to be 33.5 F.

Jan 1, 1933

By Brad Grothen, Lok Home

The choice of TBM type is never easy, but it becomes especially challenging when faced with a hard rock tunnel with expected high water flows and pressure. Slurry Shield tunneling has a long history of being used in these conditions to minimize the risk, though this method has brought with it other risks along with cost considerations. At recent projects around the world, another method has been proven to effectively manage these project risks without utilizing Slurry Shield tunneling: Shielded, NonContinuous Pressurized (NCP)-TBM tunneling in rock with a comprehensive grouting program. In this paper, the authors will analyze the use of Shielded NCP TBMs at projects around the world as compared with slurry shield tunneling in rock under water pressure. Recommendations will be given in order to establish a clear picture of the optimal tunneling method.

Jun 13, 2021

By M. F. Goudge

ROCK wool, one of the most recent additions to the list of Canadian-made, insulating materials, is a soft, light, fibrous material consisting of interlaced, flexible, glassy fibres so exceedingly fine that, individually, they are almost invisible to the naked eye and will float in air. In the process of manufacture, a suitable rock, generally a self-fluxing argillaceous dolomite consisting of nearly equal proportions of acidic and basic constituents, is melted to a completely fluid state and then converted into fibres either by a blast of steam or air, or by a mechanical device. The increase within the past five years in the number of plants in the United States making rock wool and slag wool has been remarkable, especially in view of the depressed conditions prevailing 'with most industries during this period. In 1930, there were only 8 plants reporting production of .these materials, whereas at the present time there are 44 plants in the United States listed as making these products, and there are 3 plants in Canada. In 1929, the total sales of rock-wool products in the United States amounted to-$2,377,324. In 1934, according to the National Rock and Slag Wool Association, 26 member companies reported sales of $3,695,405, and in 1935 the sale's of 30 member companies had a value of $5,571,469. The establishment of the rock-wool industry in Canada followed the publication in 1931 of a report (1) by the Mines Branch, Department of Mines, Ottawa, in which was set forth the results of field work and laboratory studies which indicated that large deposits of rock in the Niagara peninsula, hitherto regarded as valueless, were suitable for the making of rock wool. This report was supplemented in 1934 by another report (2), giving the results of further laboratory and commercial-scale tests on the rock from these particular deposits, which proved conclusively that rock wool of good quality could be made from the rock in question.

Jan 1, 1936

By John E. Roberts

People are not a novelty. But the phenomenal numbers thereof, who have approached, settled, and been born in California in the past twenty-five years, are such a problem as to be a novelty in the broadest sense of the word. California, with less than 7,000,000 people in 1940, and over 19,000,000 in 1966. In 5 1/2 years, (1960-65) the southerly 14 counties of California, which together comprise one-half the land area of our state, had an increase in population greater than Colorado, or Arkansas, or Oregon, or any one of 19 other states.

Jan 1, 1967

By W. T. Robson

Introduction Ground failure, violent or otherwise, is a problem to be contended with wherever underground operations are carried out. The character and extent of the failure, whether superficial or of more serious proportions, is determined by a number of factors, among which might be mentioned: the depth and dimensions of the underground workings; the types and distribution of wall rocks; structural features of the ore and enclosing rocks; the degree of metamorphism; the dip of the orebody; concentration of mining operations; the rate of mining; the history of the excavations made on the orebody in question. This last factor implies the consideration of such points as the arrangement and distribution of stoping both past and present, the current sequence of scoping, the type and effectiveness of the support used in old and current workings, and the amount and distribution of unmined parts of the lode. With such a variety of conditions, it is only natural that the situation at one place in a mine will not be the same as that obtaining in another part of the same mine and, more than likely, will be quite different in another property.

Jan 1, 1946

FOR some time past keen interest has been shown in both America and South Africa in the mining drill-steel problem. This interest has extended to Australian mining fields, and Australian drill users, ever desirous of increasing efficiency, are vigorously attacking the problem. The writer has recently been engaged in the investigation of the problem on two of ,the biggest mining fields in Australia, and has formed very definite conclusions concerning the causes of many drill-steel casualties. He puts these views forward in the hope that they may be of interest to, both drill manufacturers and drill users. The subject is here dealt with mainly from the aspect of the properties of the steel and the modifications of these properties whensubjected to various manipulations. It is generally admitted that the drilling machine has greatly increased in power and efficiency during recent years, and the consequence is that the machine is demanding better service from the steel. This is being impressed on the drill users by an increase in steel casualties. This fact has led many mining people to the view that the machine has developed so rapidly that the steel maker has not been able to keep pace, and that consequently the steel isfailing by fatigue 0:1; so-called crystallization. This view is rather depressing. The writer, on the other hand, is inclined to discountenance fatigue as a serious factor under good normal working conditions where the steel is carefully manufactured and supplied to the user under suitable structural and sound conditions, and has subsequently received kind treatment at the hands of the drill sharpener and the drill user.It is not reasonable to attribute failures to fatigue until it has definitely been proved that the steel is fundamentally sound and is in the best structural condition to resist the stresses it is called upon to withstand, and, this being so, that all fundamental principles of...

Jan 1, 1923

By E. H. Denny

The presence in the Cripple Creek district, Colo., of irrespirable gas or gases, generally known to consist mainly of nitrogen and carbon dioxide, has been recognized by members of the mining industry in that region almost since underground mining was begun there; the occurrence, origin, and possible control of these gases have been discussed in several articles cited at various places in this report. Similar gases have also been studied in other metal-mining districts, as later discussed. In March, 1925, there were two fatalities from rock-strata gases in the shaft of the Index mine, near Cripple Creek. Two men repairing the bell or signal line preparatory to reopening the shaft were lowered into irrespirable gases and died. Their bodies were recovered by rescue crews from the United States Bureau of Mines and .the Portland mine, Victor, Colo. These crews found it necessary to use oxygen breathing apparatus. In October of the same year a miner was trapped on the 6 level of the Midget mine by an influx of gases that filled the shaft to a point above that where he was working. Oxygen breathing apparatus was again used by Bureau of Mines employees, who were in the vicinity, and the man was brought out in time to save his life. These two fatalities and one near fatality seemed to show that additional investigation of the gases and methods of control might be warranted. Accordingly, field and laboratory studies were begun by the authors of this report after a visit to the district by M. van Siclen, then engineer in charge, mining research division, Bureau of Mines, and after conferences with the Mine Owners' Association of Cripple Creek and with J. T. Joyce, metal-mine commissioner of the State of Colorado. The mine operators of the Cripple Creek district and the State mine commissioner's office gave whole-hearted cooperation in this work.

Jan 1, 1930