Search Documents

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

By S. S. Clarke

ABOUT two years ago some of my friends were discussing the amount of drill-steel breakage that was permissible or not excessive, per month, per rock ton, per ton of steel or any unit of measure or output that would give a comparison between different kinds of drill steel. No one seemed to know what life to expect of steel, or what percentage of breakage might be termed excessive. In fact there were no operating data available to guide one in selecting the best steel for our mines, nor could any ideas or information be secured from the steel manufacturers. One was merely told that so and so used their steel and it was very satisfactory; or else one was given a highly technical lecture on their specific heat-treatment. Any estimates on expected breakage were just guesses, ranging from a fraction of a per cent to as high as ten per cent per month.

Jan 1, 1933

By Ana Clara Petrucelli

A principal ferramenta de controle do processo BOF reside na regulagem do sopro de oxigênio. A análise dos parâmetros de interação entre o sopro e o banho metálico compõe o objetivo deste trabalho. Através de uma análise visual da penetração e fração volumétrica da bacia de descarburação, foi determinada a melhor configuração de sopro entre diferentes combinações de bicos multifuros (3 a 6 furos), distância lança-banho e vazão. Foram feitas previsões sobre a penetração do jato a partir de um balanço de energia a fim de validá-las com o modelo físico. As maiores penetrações foram alcançadas com os bicos de 3 e 4 furos, com a maior vazão e menor distância lança-banho dentre os padrões testados. Todavia, as maiores frações volumétricas da bacia de descarburação foram obtidas com 5 e 6 furos, vazão e distâncias variadas dentre as ensaiadas.

Jul 29, 2018

By João Vitor Mokan

O presente trabalho avalia o efeito das camadas de conversão a base de CrVI e CrIII aplicadas na superfície de arames galvanizados por imersão a quente. As bitolas testadas foram 1,24mm, 1,65mm e 3,00mm, utilizando os ensaios de Névoa Salina e Câmara Úmida, avaliando o aspecto superficial dos arames após 1, 3, 6, 24 e 28 horas de exposição ao ambiente agressivo. Pode ser observado que o ensaio de Névoa Salina é pouco indicado para avaliar a oxidação superficial do arame em função de sua agressividade. Os resultados foram melhor interpretados utilizando o ensaio de Câmara Úmida. Inicialmente os arames recobertos por uma camada de conversão a base de CrIII apresentaram desempenho levemente superior àqueles recobertos por CrVI, considerando os mesmos tempos de exposição. Após seis horas os arames galvanizados apresentaram comportamentos semelhantes. O arame galvanizado com maior resistência a oxidação foi aquele protegido com CrIII, porém com o passar do tempo os dois tipos de revestimento se equivalem.

Oct 30, 2017

By Gilvandro Bueno

Atualmente, diferentes tipos de vedações laterais de rolos, usados para limitar o efeito de borda em prensas de rolos “High Pressure Grinding Rolls (HPGR)” se encontram disponíveis. O presente trabalho comparou dois métodos usados na vedação lateral: as placas laterais (cheek plates) e as flanges, essas últimas colocadas em um dos dois rolos, a partir de simulações usando o Método dos Elementos Discretos "Discrete Element Method (DEM)", com acoplamento dinâmico multicorpos (Multibody dynamics ou MBD). Como resultado das simulações foram obtidos os perfis de força compressiva ao longo do rolo, assim como a proporção do fluxo mássico de alimentação que é projetado fora da zona de compressão durante a prensagem. As simulações mostraram que ...do HPGR usando o DEM + MBD se apresentam como uma ferramenta muito útil para visualizar o melhor modelo de vedação de modo a minimizar o efeito de borda durante o processo de prensagem.

Oct 30, 2017

By P. Ramsaywok, G. Legodi

Spiral concentrators are widely used in the coal industry treating fine (-1mm) coal. Their application was a limitation to the product quality until the introduction of low-cut spirals which allow a lower quality ash product to be produced, thus expanding the market. The Exxaro Grootegeluk 1 (GG1) plant has a two-stage traditional rougher-cleaner spiral circuit using conventional SX4 spirals to produce semi-soft coking coal product at 12.5% ash by mass. The overall plant product is 10.3% ash meaning that the coarser sized coal dense medium separation circuits must compensate. A low density cut-point spiral targetting 10.3% ash would thus be beneficial to the overall complex. The spirals were tested in the two-stage plant environment and in a pilot plant. This paper discusses the findings and compares a two stage four-turn low density cut and conventional spiral. The two spiral technologies were unable to sustain a 10.3% ash product. Pilot test work was also conducted on GG1 coal, demonstrating that an eight-turn low density cut-point spiral achieves the targetted 10.3% ash under controlled conditions. Keywords: Spiral, low-cut, coal

Jan 1, 2020

By J. U. Burger

The Elizabeth Bay aeolian deposit in Namibia comprises a sedimentary package of diamondiferous grits that have been deposited, reworked and concentrated to various degrees by dominant southerly winds. Diamond concentration in these deposits is highly variable and often unpredictable. The deposit is marginal from an economic perspective and therefore requires selective mining which in turn requires correct sampling and accurate estimation. Three methods of sampling have been used at Elizabeth Bay for mineral resource estimation: (i) pit samples utilizing an excavator to produce a sample 1 to 3 metres deep with a 10 to 20 m2 footprint, (ii)GB50 grab sampling with a 3.34 m2 footprint and (iii) a BG36 bucket auger drill with a 5 m2 footprint. Pit sampling, being easy to execute, has been the most widely used despite a limited penetration ability and, at times, questionable integrity. The GB50 grab sampling tool was tested at Elizabeth Bay and although it had better penetration ability and sample integrity, it struggled with cemented horizons. No sample optimization was conducted prior to the GB50 grab sampling. The latest phase of sampling was conducted using a BG36 bucket auger drill which is capable of penetrating thick overburden, penetrate cemented horizons and provides an acceptable sample support size. Geostatistical simulation methods were applied to establish the optimum sampling parameters required to estimate a mineral resource at an indicated level of confidence. The results show that a 5 m2 sample support size is adequate and that a 50 m 100 m sample configuration is optimal. Sample data obtained from the three methods confirms that the BG36 bucket auger tool combined with the parameters identified in this exercise produce the best results for diamond resource estimation.

Jan 1, 2009

By E de Necker, F D. I Hodg, L-M Cruywagen

The acid mine drainage (AMD) situation at three opencast collieries in the Witbank Coalfield, South Africa, was evaluated from different perspectives. Twenty-seven test pits were dug into the spoils of these collieries to characterise the in situ conditions of spoils of varying age. Detailed static testing was done on surrounding drill holes and additional samples were taken from the test pits. Selected samples were tested using different techniques, namely ABA, mineralogy and kinetic tests. Groundwater monitoring boreholes from the areas surrounding these spoils were also used for characterisation. The ABA results compared favourably with the in situ determinations; acidic test pits proved to be potentially acid-generating from ABA, even when the samples had neutral paste pH. Kinetic test results showed these samples to yield low pH leachate over the test period. In several of these results, the theoretical depletion of neutralising potential and the onset of acidity were well matched. NAG pH-values and final observed water chemistry corresponded for the cells predicted by ABA to acidify, but compared poorly in cells that did not acidify. Results from the non-acidic spoils were consistent with the in situ observations. Alternative kinetic test methodologies were also employed. Duplicate samples were tested in humidity cells and in aerated trays that were manually wetted on a regular basis. Results from these tests showed an excellent correlation. Detailed mineralogical determinations using XRD and XRF were used for comparison to the ABA and, in some cases, humidity cell results. These comparisons show that the ABA results are consistent with the results expected from the mineralogy. The conclusion from these assessments is that ABA, in most cases, provides information that can be correlated to the field, mineralogy and to humidity cells. The use of multiple techniques leads to a higher degree of confidence in the use of the data.

Jan 1, 2003

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

By R. E. Mitchell

The environmental impact assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another increasingly common evaluation system for proposed projects is the environmental, social and health impact assessment (ESHIA). An ESHIA differs from an EIA for its generally more comprehensive and inclusive approach to evaluating potential impacts, such as on public health, and other features such as an ecosystem services approach to assessing biophysical and community impacts. An ESHIA may also be required by certain lenders for financing major projects. In this paper, EIA standards for the province of Alberta, Canada are discussed and compared to ESHIA. It concludes with several recommendations for consideration.

Jan 1, 2012

Comparing Energy Efficiency of Multi-Pass High Pressure Grinding Roll (HPGR) Circuits With increased emphasis on reducing costs and carbon emissions in mineral processing, it is becoming essential to employ the most efficient comminution devices and to use them to maximum effect. High pressure grinding rolls (HPGR) are considered highly efficient compared with other devices, however their relative efficiency in multi-HPGR circuits is less well understood. A series of comminution tests was carried out to evaluate three multi-pass HPGR circuits and a jaw crusher-ball mill circuit. Combinations of HPGR units (1.0 m and 0.25 m diameter), jaw crushers and Bond ball mills were used to grind a 32 mm top size porphyry copper feed (BBWI = 12.1) to a product P80 size of about 150 ¦m. Up to three passes of HPGR were used in each circuit, with energy measurement and size analysis at each point in the comminution process. The energy efficiencies of individual comminution stages and of the overall circuits were quantified and evaluated using three different approaches. The operating work index method for comparing comminution energy efficiency underestimated HPGR performance due to the large amount of fines generated. The -75 ¦m efficiency factor and F50/P50 reduction ratio interpolation methods both give a fairer measure because they better take into account the amount of fines generated by HPGR. The results show that the relative comminution efficiencies of the three multi-pass HPGR circuits tested differ by as much as 22%, providing insights as how to best employ HPGR in a comminution circuit. The most energy efficient of the circuits tested was a three-pass HPGR circuit with a 1.0 m diameter roll on the first pass in closed circuit with an 8 mm screen followed by a second and third pass in a 0.25 m roll.

Sep 13, 2010

By S. J. van Rensburg

Competition for resources, including water and arable land, refocused attention on water and gold tailings management with respect to quantity and quality. MINTEK established and validated an "Advanced Leach Facility" to record kinetic leach information aimed at gold refractory sulphide ores. This facility was developed because of the need for additional leach process information to enable proactive decision making. Instead of focussing on optimised gold recovery only, the impacts of pre-oxidation methodologies were evaluated by considering key parameters, including cyanide speciation, reagent consumption, thiocyanate, arsenic, heavy metals, salt loads, water quality and residue stability. Results from oxidative leaching of a refractory gold ore employing oxygen, ozone, ultra-fine grinding, high shear and pressure oxidation are discussed. The relative cyanide and lime costs and environmental and sustainability effects associated with these technologies are briefly outlined.

Jan 1, 2011

By V. A. Leão, A. M. Silva, S. M. Bertolino, B. C. S. Ferreira, D. Guimarães

Although not considered a high risk pollutant as compared to toxic metals and acidity, environmental agencies worldwide are proposing regulations to control sulphate in effluents and drainages by setting a threshold value varying between 250 mg/L and 500 mg/L. The aim of this study was thus to compare four different techniques for removing sulphate ions from mining/metallurgy effluents. The first alternative studied was sulphate removal by precipitation as ettringite. Treating a synthetic solution containing 1650 mg/L sulphate at 22±1 ºC resulted in removals close to 85% during continuous precipitation. Sulphate sorption was also investigated using three different ion exchange resins as well as limestone. Fixed bed experiments produced sulphate loadings of up to 70 mg SO4 2-/L resin, at pH 2.0. In neutral wastewaters, limestone is also a potential adsorbent producing a maximum particle loading of 19 mg/g. Sulphate sorption on limestone seems to be an alternative to treating mine waters with sulphate concentrations below the 1200-2000 mg/L range, where lime precipitation is not effective. Subsequently, sulphate removal by sulphate reducing bacteria was also investigated and it was observed that reactor’s hydrodynamic conditions and the choice of substrate are important factors for the process. The different technical aspects of each technology are addressed.

Jan 1, 2014

By J. Noll, J. A. Organiscak, A. B. Cecala

"In recent years, significant strides have been made to optimize the design of filtration and pressurization systems used on enclosed cabs of mobile mining equipment to reduce respirable dust and other contaminants and provide the best air quality to the equipment operators. This synergetic effort has involved original equipment manufacturers building mining equipment, manufacturers of heating, ventilation, and air conditioning systems for mobile equipment, filtration and pressurization system manufacturing companies, as well as the National Institute for Occupational Safety and Health, and other government organizations. Considering all the advances made in this area over the last decade, one aspect that NIOSH still needs to assess is the longevity of optimal cab performance with respect to the quality (filtering efficiency) of the filters used in filtration and pressurization systems. In today’s culture, most health and safety professionals automatically believe that HEPA quality filters need to be used to provide the greatest level of protection to workers. Researchers at the Office of Mine Safety and Health Research for NIOSH hypothesized that HEPA quality filters may not be optimal for the mining industry and speculated that MERV 16 rated filters would be more appropriate in most cases. In order to test this hypothesis, NIOSH performed a two-year study comparing both HEPA and MERV 16 quality filters on two pieces of underground limestone mining equipment, being a roof-bolter and face drill machine. Testing showed at the 95 pct. confidence level that there was no statistical difference between the two efficiency filters on both pieces of mining equipment. Since the MERV 16 rated filters were less restrictive and provided greater cab pressure, and since they did not have to be replaced as often as the HEPA quality filters, researchers concluded the MERV 16 filters were the optimal choice for both pieces of mining equipment in this case study comparative analysis. INTRODUCTION When most health and safety professionals today think about filtration efficiencies and their correlation with protecting workers’ health, the normal assumption is the higher the efficiency of a filter, the greater the protection afforded to the workers. The next logical step is to believe that HEPA filters deliver the greatest protection for workers because they provide the highest filtering efficiency. Obviously high-efficiency intake filters are a necessity for an effective cab filtration and pressurization system on mobile mining equipment, but what is the optimal filter efficiency rating for achieving high levels of cab protection factor performance over the service life of filters? To address this question, the National Institute for Occupational Safety and Health (NIOSH) has performed an in-depth laboratory research study over the years simultaneously with numerous field studies to retrofit used enclosed cabs on mobile mining equipment with newer and more effective filtration and pressurization systems."

Jan 1, 2016

By S. Stuurman

Inorganic acids such as sulphuric acid have found use together with certain reducing agents in leaching of copper-cobalt oxide ores. These reagents are not ideal due to the adverse effect the inorganic acids generally have on the environment and the high costs of the reducing agents. In this study a copper-cobalt oxide ore from the Central African Copperbelt was leached in two different environments; sulphuric acid in conjunction with hydrogen peroxide as a reducing agent and tartaric acid. The effects of acid concentration, reducing agent concentration, and temperature were independently determined for both leaching environments. The sulphuric acid concentration was varied between 0.4 M and 1.2 M and the concentration of hydrogen peroxide between 4.0 M and 6.5 M, while the tartaric acid concentration was varied between 0.15 M and 0.35 M. The temperature was varied between 20°C and 50°C. The results showed that the extraction of both copper and cobalt increased with sulphuric acid concentration, reaching a peak at approximately 0.8 M and then decreasing at higher acid concentrations. A similar increase and decrease in metal extraction was observed when the reducing agent was increased. In leaching with tartaric acid, the extraction of cobalt was much higher than that of copper, although extraction of both metals increased with acid concentration. Additions of small amounts of hydrogen peroxide were found to increase cobalt extraction in tartaric acid but had a minimal effect on copper. An increase in the solution temperature had a significant effect in the organic acid environment, with the effect on cobalt extraction being much more pronounced than on copper.

Jan 1, 2014

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

Researchers from the U.S. National Institute for Occupational Health and Safety (NIOSH) studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the continuous personal dust monitor) within a sociotechnical system (STS) framework to mitigate respirable dust sources. The results address how to best incorporate the overarching principles of meta-design STS during the technology integration process. Specifically, quantitative and qualitative data show that a prominent focus on the social factors within an STS framework could help reduce organizational unpredictability and may improve communication within the system to help reduce technology adoption time.

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

By J. Petersen, A. E. Lewis, J. Chivavava

Rare earth elements (REEs) have special properties that prompted their extensive use in high-tech applications. The demand for REE has, therefore, increased over the past years, resulting in the supply risk of the materials. Extraction from non-conventional low-grade ores, like easy-to-mine ion adsorption clays (IACs), by hydrometallurgical methods is being explored to supplement the supply of REEs. The extraction of REEs from low tenor IAC leach solutions requires enrichment using cost-effective methods such as precipitation. Therefore, the aim of this study was to understand the recovery of REEs from IAC leach solutions using various reagents for precipitation. In the first part of the study, recoveries of REEs from IAC leach solutions through direct precipitation using H2C2O4 and NH4HCO3, as well as antisolvent crystallization using C2H5OH, were predicted via thermodynamic modelling using OLI Stream Analyzer. Verification experiments were then conducted through the use of an agitated reactor. Simulation results showed that high yields of REEs were possible using each of the reagents, but large quantities of C2H5OH were required. Experimental results confirmed the high yields predicted from simulations. Precipitation with H2C2O4 was found to selectively recover REEs while rejecting Al. However, utilization of NH4HCO3 and C2H5OH resulted in the co-precipitation of Al. Furthermore, the yield of Y from antisolvent crystallization was significantly lower than the theoretical value. The product recovered from antisolvent crystallization consisted of well faceted, large crystalline particles, which filtered faster than the fine, amorphous REE carbonates recovered using NH4HCO3. REE oxalates were crystalline, larger than the REE carbonates and, overall, showed the highest filtration rate.

Dec 11, 2024

By R. Patterson

Tracer gas sampling methods are useful for monitoring ventilation systems, especially in remote or inaccessible areas, and can be utilized for analysis of the ventilation system immediately following a mine emergency. However, the success of this technique is largely dependent on the accuracy of release and sampling methods. Analysis of sampling methods is crucial for rapid response and dependable results during emergencies. For the purpose of this study, four well-accepted sampling techniques currently used in the mining industry were compared using solid-phase microextraction (SPMe) fibers with sulfur hexafluoride (SF6), an industry standard, as the tracer gas. Current sample collection techniques include plastic syringes, glass syringes, Tedlar bags and vacutainers. SPMe fibers are used in a variety of industries, from forensics to environmental sampling, and are a solventless method of sampling analytes. To analyze these sampling methods, samples were taken from a 0.01 % standard mixture of SF6 and nitrogen and analyzed using electron capture gas chromatography. A relative standard error of less than 10% validated results to compare the accuracy of various methods. The technical and practical issues surrounding each sampling method were also observed and discussed.

Jan 1, 2011

By Elaine Ellingham, Francis T. Manns

"Abstract -The Orostar and Scadding were two small gold mines owned and operated by Orofino Resources Limited. Conventional statistical treatment indicates an identical arithmetic mean grade of 0.22 oz/T Au for both mineable reserves. Further, the deposits are both shown to have cut weighted average reserve grade of 0.21 oz/T. Orostar mined out at 0.206 oz/T and Scadding at0.156 oz/TAu . The combined exploration and development database contained 1394 fire assays, more than enough for statistical confidence in a normal distribution. Therefore this study was initiated to determine, if possible, why the mill head grades were lower than the averages and to experiment with several methods to determine whether a reliable statistical mill head grade estimation method would emerge. Despite the identical reserve grades, distinct differences in the grade distribution histograms are present. By studying the arithmetic and log-normal grade distribution s, with some attention to South African practices, this paper reports on those differences which may account for the considerable divergence in the mill head grades. Furthermore, this study casts considerable doubt on the industry standard method of cut weighted averages.The global mill head grades of the two deposits have been derived from the arithmetic average grades by graphic means. This precise method of mill head grade prediction, if applied to complex orebodies, could permit selective grade control and result in direct cost savings by allowing the operator to detect false value stopes, benches or levels and emphasize reliable regions of not only gold mines, but also uranium or base metal deposits."

Jan 1, 1992