Search Documents

By M. R. Geer, H. F. Yancey

Four coals were treated in the Humphreys spiral concentrator, and the products were examined by float-and-sink and screen-sizing tests to determine fundamental performance characteristics. The efficiency of the separation between coal and impurity was shown to be influenced greatly by particle size.

Jan 1, 1950

By Whitman E. Brown

The installation in 1948 of a Humphrey spiral concentrator section at the Hill-Trumbull plant of The Cleveland-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus 1/8 in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 44 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus 1/8 in. size. After desliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant.

Jan 1, 1949

By James A. Robertson

"In the Blind River area Proterozoic clastic and sedimentary rocks and minor volcanic rocks (The Huronian Supergroup) uncomformably overlie and trangress northwards over dominantly granitic Archean terrane (2500 + Ma) and are intruded by Nipissing Diabase (2ll5 Ma). Later deformation and metamorphic events are recognized. The developing depositional basin was controlled by the incipient Great Lakes Tectonic Zone marginal to the Algoman Craton.The Matinenda Formation (basal Huronian) comprises northwards-derived fluvial arkose, quartzite, and pyritic, uraniferous oligomictic conglomerate which contained in 1981 some two-thirds of Canada's uranium resources. Production to December 1981 from Elliot Lake totalled 98.3 thousand tonnes U for an average recovered grade of 0.1% U with an additional 671 tonnes U recovered by leaching at Agnew Lake. The remaining resources are at lower grades. Some thorium and yttrium have been produced. Minor amounts of gold reflect the paucity in the source area. Gold is better-developed in the Huronian north of Sudbury reflecting the local source area.The conglomerate beds lie in southeasterly-striking zones controlled by basement topography down sedimentation from uraniferous Archean granite. Uraninite textures, the distribution of monazite, and local enrichment by reworking indicate a syngenetic, probably placer, origin of the mineralization. ""Brannerite"" has formed by solution of uranium from the margins of the uraninite grains and redeposition on the original titaniferous minerals. Penecontemporaneous volcanics may have been a source for sulphur in some of the pyrite and of trace amounts of Co, Ni and Au. Some pyrite may be detrital, some may be authigenic and some introduced.Drab coloured rocks, uranium and sulphide mineralization, the presence of hydrocarbon (thucholite) and a post-Archean regolith formed under reducing conditions have been cited as evidence of an early Precambrian reducing environment extended to the atmosphere. Sedimentary features indicating fast-flowing water and possibly a cold climate imply that the uraninite would be exposed to whatever oxygen was present in the atmosphere under conditions which would inhibit complete solution. In the upper Huronian, red beds and in the Lorrain Formation a monazite - iron oxide assemblage and copper mineralization indicate more oxidizing conditions. . Similar uranium deposits occur at Agnew Lake and in the basal Huronian north of Sudbury there are minor uranium and gold values.Provenance, lack of complete oxidation, transportation and depositional processes, redistribution during diagenesis and possibly low grade metamorphism, and the lack of post-depositional destructive processes are the dominant factors in the formation and preservation of the ores. The modified placer theory of genesis is well entrenched and an exploration model for such deposits throughout the world is well-documented.Research continues on mineralogy and textures of the ores, detailed sedimentology of the ores and their host rocks, with particular emphasis on: provenance area, the influence of early Precambrian mineralization patterns on the mineralization present in the Huronian both in space and in time, fluvial sedimentation and diagenesis. Expansion and reopening of the mines of the Elliot Lake camp should facilitate further studies."

Jan 1, 1986

By Nick Vayenas, Ming Cai, Hongbin Zhang Lorrie Fava, Enrique Acuña

"A hybrid methodology is proposed to improve the accuracy of Diesel Particulate Matter (DPM) concentrations simulated in a ventilation network model by using Computational Fluid Dynamics (CFD). DPM, as a primary concern for underground hard-rock mines, has been studied in two dominant numerical models, ventilation network solvers and computational fluid dynamics. Ventilation network solvers are efficient, but they are not able to provide three-dimensional DPM concentration contours and only accept area-average DPM data as input. CFD simulations are time-consuming, but generating DPM concentration results with high accuracy. Besides, both monitoring points and planes can be created in a CFD model, which can take both point data and area-average DPM data as input. The hybrid methodology is intended to combine the advantages of the two by using the CFD results to update the network model results at key locations. A field study was conducted in a dead-end heading in an underground gold mine in the United States. Real-time DPM monitors were used to collect data. A CFD model and a network model were built for the experiment area. The CFD model was calibrated to the experimental data. In the study presented here, results from a calibrated CFD model are converted to equivalent diesel emission rates in the ventilation network model at a shared outlet. The hybrid methodology is used to provide better input for the network model. INTRODUCTION Mine ventilation system is one of the most important parts for an underground mine. It not only provides fresh air to the personnel but also helps clear the contaminants generated from the diesel-powered equipment. For most underground metal and non-metal mines, diesel particulate matter is the main contaminant. It is also the focus of this paper."

Jan 1, 2019

By Charles G. Crans, Naresh Gurpersaud

"Toronto’s Union Station, a National Historic Site occupying an entire city block, is the busiest commuter rail transportation hub in Canada. An extensive project is being undertaken to revitalize Union Station while maintaining the historical significance of the building and minimizing disruption to commuters. A significant stage of the revitalization involves excavation indoors, to a depth of up to 5.5 m below the existing floor level to create space for a new transit concourse and a new lower-level pedestrian retail concourse. A hybrid excavation support system utilizing micropiles as soldier piles was constructed over an 18 month period between 2010 and 2011.Development and testing of connections between the micropiles, shotcrete facing, lagging, walers, and tiebacks presented significant challenges. The existing viaduct structure was constructed in the 1920’s on land reclaimed from Toronto Harbour, so there was significant (and ongoing) uncertainty with respect to buried obstructions including relic timber wharfs and abandoned steel and timber piles. Collectively all these conditions precluded the use of conventional methodology; new techniques, installed using modified equipment, and for the first time in the Greater Toronto Area, were required.Details of the existing site conditions, installation challenges, design, construction and performance of the hybrid excavation support system inside this historic structure are presented.INTRODUCTIONUnion Station in Toronto, Ontario is the busiest passenger rail facility in Canada, with 65 million passengers annually and an average of 200,000 passengers each day. Construction of the station was completed in 1920. It has been designated a National Historic Site of Canada and inducted into the North America Railway Hall of Fame in the Facility and Structure category.The Union Station Revitalization Project (USRP) was tendered in 2010 and awarded as a 6-year, $450M construction management / trade contract package. Included was a large scale grade reduction, referred to as “The Dig Down”, to create two basement levels and this required extensive excavation support constructed entirely indoors within the active station setting."

Jan 1, 2017

By L. Dubourg, H. Habibi, D. Rasmussen

The combination of laser welding with Gas Metal Arc Welding (GMA W) forms the hybrid laser-OMA W welding. This process is an attractive tool with a high potential in welding lightweight structures, especially for aluminum alloys. For five years, this technology has increasingly attracted interest in both, industry (aeronautics, automobile, metal industries producing large structures) and academia (universities and research centers). Hybrid laser-OMA W welding process is generally accepted for its robustness, efficiency and flexibility. Coupling of a deep-penetrating laser beam with the heat and molten metal feeding of GMA W significantly expands the original welding application range of lasers. Its main advantages compared to the two individual components are deep and stable weld penetration, gap-bridging ability improvement, low distortion and easy filler metal addition. Hybrid welding allows a much wider groove tolerance compared to laser welding, especially for aluminum welding. Moreover, the reduction in distortion decreases the post-welding rectification needed and makes the assembly easier. In addition, if metallurgical factors are critical, the weld composition can be balanced with filler metal, decreasing the hot cracking susceptibility of some aluminum alloys. The combination of these two welding processes can also improve the weld bead shape quality (including the elimination of undercut), possibly reduce the porosity and increase the welding speed. This article reviews the recent works about the laser-OMA W hybrid welding of aluminum alloys. After a brief presentation on the interaction mechanisms between a laser beam and an electric arc, the paper depicts the typical welding parameters and experimental methods along with their characteristics.

Jan 1, 2006

By III Scotland

Genstar's underground mine at Texas, MD experienced a failure of the mine roof and subsequent damage to an underground backfill caused by surface floodwaters. A hydraulic backfilling program was developed in house to stabilize temporary repairs to the mine roof, replace 2300 yards of pneumatically stowed backfill, and complete a permanent repair to the mine roof. A flowable backfill material was developed, tested, and later marketed as the result of experience gained during this project. In addition, Genstar personnel developed backfilling techniques to meet the requirements of the repairs and completed work without the additional expense of non company services or contractors.

Jan 1, 1992

By D. L. Koch, J. W. Tester, L. K. Sinclair

"In this study, hydraulic conductivity (K) geostatistics were used to predict residence time distribution of well-to-well flow. Flow profiles, fracture density measurements, and pumping tests were available from the highly fractured Florence Copper in situ leaching site. The flow profiles were used to establish the statistical distribution and spatial autocorrelation of K. Two tests were used for validation. The first test confirmed that fracture density and K are autocorrelated over similar length scales. In the second test, Monte Carlo flow simulations successfully recreated the results of pumping tests. Flow sim¬ulations were used to stochastically model well-to-well residence time distribution. RÉSUMÉ Dans cette étude, nous utilisons la géostatistique de la conductivité hydraulique (K) pour prévoir la distribution des temps de séjour (DTS) de l’écoulement entre les puits. Des profils de l’écoulement, des mesures de la densité des fractures et des essais de pompage existaient pour le site fortement fracturé de lixiviation in situ de Florence Copper. Les profils de l’écoulement ont permis d’établir la distribution statistique et l’autocorrélation spatiale de K. Deux essais ont servi à la validation ; le premier a confirmé que la densité des fractures et K sont autocorrélés sur des échelles de longueur similaires ; quant au second, des simulations d’écoulements de type Monte Carlo sont parvenues à reproduire les résultats des essais de pompage. Les simulations d’écoulement ont servi à établir un modèle stochastique de la DTS de l’écoulement entre les puits.INTRODUCTION In situ leaching is the circulation of a dilute acid or base solution in the subsurface, via a series of injection and recovery wells, to dissolve a target metal. In situ leach modelling requires forecasting the residence time distribution (RTD) of flow between wells. In fractured formations such as copper porphyry deposits, order-of-magnitude variations in hydraulic conductivity (K) can result in highly channeled flow, resulting in a heavy tailed RTD (Becker & Shapiro, 2003; Kang, Le Borgne, Dentz, Bour, & Juanes, 2015). Channeling through preferential pathways has impacted copper recovery at several past in situ leaching field tests (Cathles, Glenn, Lenzi, Nigrini, Deans, & Huff, 1978; Ahlness & Pojar, 1983; Schmidt, Earley, & Friedel, 1994; Sinclair & Thompson, 2015). The aim of this work is to combine multiple types of hydrogeological measurements to stochastically forecast the well-to-well RTD in fractured rock for the purposes of copper in situ leach modelling."

Jan 1, 2018

By C. Özgen Karacan

This study presents the results of core-log analyses from the exploration boreholes, the analyses of face advance rates, and the results of downhole monitoring studies performed in gob gas ventholes for calculation of changes in hydraulic properties in the longwall overburden at a mine site in southwestern (SW) Pennsylvania section of Northern Appalachian Basin. In the ?rst part of the study, coal measure rocks in overburden strata were analyzed and the locations where possible fractures and bedding plane separations would occur were evaluated. In the second part, the hydraulic conductivities were computed by two different slug test analyses methods using the water level changes measured in gob gas ventholes as longwall face approached. Hydraulic conductivities were analyzed with respect to the changes in overburden depth, the locations of the borehole, and mine face advance rates. These data were used to interpret the potential productivities of the gob gas ventholes as a result of fracturing and changes in hydraulic conductivities. The general results showed that the probability of fracturing and bedding plane separations in the overburden increase between strong and weak rock interfaces. Also, the probability of bedding plane separations increases as the interface is close to the extracted coal seam. Evaluation of slug tests showed that the hydraulic conductivity developments in the boreholes and their potential production performances are affected by the underground strata and the roof materials. In situations where the roof material is stiff and thick, the development of high permeability fractures around the borehole will be less. Results also indicated that borehole location with respect to face position affects the fracturing time and permeability evolution as well. Greater overburden depths generally cause earlier fracturing as longwall face approaches, but eventually result in lower hydraulic conductivities and potentially less effective boreholes. Increasing mining rates also resulted in generally lower hydraulic conductivities in the overburden. The results of this study were intended to improve the interpretation of gob gas venthole performance and to provide better siting of these boreholes.

Jan 1, 2009

By Henry G. Granger

I. INTRODUCTION. REPEATED failures in attempts to work gold-bearing gravels by means of suction-dredges have created the impression that this method is impracticable. The suction-dredges have failed from three special causes excessive wear and frequent breakage of pump-shell, runners and liners; inability to dredge compact gravel which would ,not. readily move towards the intake; and, most important of all, closing. of the suction-pipe by stones too large to enter it. In my opinion, all three causes of trouble may be remedied: the first, by making stronger the parts most liable to wear and breakage; the second, by means for loosening the gravel at the intake; and the third, by sufficiently... Increasing.. the diameter of the suction-pipe. In suction gold-dredges, this diameter has not usually exceeded 10 or 12 in.; whereas there are few profitable gold-fields which can bee considered dredgeable, in which stones more than' 12 in. in diameter, are-.not frequently encountered. II. AN EFFECTIVE SUCTION-DREDGE. In harbor-operations, much larger stones are handled by suction-dredges.., The large dredge of the Henry Steers Contracting Co. worked for nearly four years at League Island, Philadelphia, where it sucked up, passed through the pump, and forced through 3,700 ft. of discharge-pipe; gravel containing boulders up to 200 lb. in weight. This was done with no bad breaks and few shut-downs. The cutter; and liners were the only parts liable to damage, and these were easily replaced with brief interruption of work. The chrome-steel liners are said to have lasted from six to nine months. I am informed that this dredge worked continously for nine

Apr 1, 1909

By E. A. Sobering

Hydraulic filling or sand filling is a system used to fill underground excavations with a dense pulp. Milltailings are commonly used. The resultant fill, after being placed and de-watered, is known as hydraulic fill. These fills have been effectively used to (a) provide immediate support of the workings place during stoping; (b) .facilitate the recovery of pillars; (c) limit surface damage by subsidence; (d) permit the mining of parallel hanging-wall orebodies; (e) stabilize the ground in mines, thereby reducing the rock burst hazard; (f) control and prevent mine fires; and (g) solve tailings disposal .problems. The various uses of hydraulic filling have been developed during the last ninety years. In 1864 it was employed only to control surface subsidence. Since then, this system has been successfully applied to meet specific ground support problems. Methods of handling mine-fill derived from a source outside the stope include transportation ?Of the material by hand, mechanical, pneumatic, and hydraulic means, or a combination of these methods. The hydraulic method has many advantages not found in the others; a significant advantage is the low compressibility of the material when compared to other mine-fill material. The hydraulic filling operation includes the .preparation and transportation of the pulp. The underground practices in .placing the fill vary from mine to mine. The chief reason, formerly, for using hydraulic fill was the exceptional support it provided, but recently it has proven an important means of reducing mining costs. This is especially true where labour is a large part of an alternative method, or where timber consumption is greatly reduced. The indirect benefits of hydraulic filling are probably as important as the direct benefits, and few important disadvantages exist.

Jan 1, 1956

By Tim Deans

This paper will address methods to manage hydraulic hose and coupling inventory so that parts will be available to build assemblies for the vast majority of equipment with as little inventory as possible. Topics also to be covered will include some basic hose assembly tagging techniques that will help keep equipment running by tracking problem hoses and building ?band aid? kits, having problem hoses premade in stock, and inventory usage tracking (one of the biggest problems for any inventory manager is knowing which couplings have been used so they can re-order). Cradle to grave tracking of hydraulic and industrial hoses insures reliable service of vehicles and ethical disposal of old hoses and couplings. With accountability for disposal of hose products that may contain chlorine (neoprene tube material in some hydraulic hoses) and carbon black that will be scrutinized more closely in the future, a proactive approach should be adopted in order to minimize maintenance facility problems.

Aug 1, 2013

By P. Kostuik

"Recent interest in the pipeline transport of solid mate-als has been sparked by the idea that, in an inflationary onomy, pipeline costs are more stable than the costs of any other transport systems. Pipelines have proved over 1e years to be dependable, records indicate that main-•nance and operating costs are comparatively low, and 1eir amenability to automation is of considerable im->rtance.The concept of hydraulic hoisting of solids from under-round, or cross-country hydraulic transportation of con-~ntrates and ores, is currently of prime interest to the ining industry. In general, this paper deals with a preliminary investi-ation of energy losses incurred while transporting a rela-vely heavy, crushed mine product, namely magnetite, oth vertically and horizontally. The basis and validity of everal equations derived by other experimenters to com-ute these losses is discussed. A theoretical analysis of ydraulic hoi:,,ting is made, and, based upon test results, calculation of horsepower requirements for hoisting an re under a given set of conditions is presented. Results indicate that:n vertical transport, the friction head losses are identical to those of clear water, and the total energy requirement for hydraulic hoisting then becomes a function of height of lift, concentration and specific gravity of the solids being hoisted. .-In horizontal transport, friction head losses can be calculated with reasonable accuracy using Bonning-ton's correlation curve. Losses computed utilizing Durand's correlation (K = 85) result in estimates which are too low by 10 to 30 per cent, an<l those calculated using Newitt's correlation (K = 1,100, K = 66) give friction loss values which are too high by 10 to 30 per cent . . -The theoretical horsepower (RMS-hp.) required for hoisting hydraulically is approximately half of that required for conventional double-drum skip hoisting."

Jan 1, 1966

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

This study developed machine learning (ML) models for predicting rock formation reactive forces experienced by a hydraulic shovel bucket during excavation. To do this, rock formation in the form of muckpile was modeled as granular ball elements in three-dimensional particle flow code (PFC) using linear bonding logic. A typical field-size hydraulic shovel bucket modelled in AutoCAD was used to excavate the rock formation and the three-dimensional shovel bucket resistive forces required to cut through the rock formation were measured and recorded. The experiments involved different muckpile height, bulk densities, repose angles, and average fragment size. Six ML algorithms, artificial neural network (ANN), K-nearest neighbor (KNN), linear, random forest (RF), regression tree (RT), and support vector machine (SVM), were evaluated on their ability to predict the shovel bucket resistive forces. The input variables used for the prediction of the resistive forces were the muckpile bulk density, angle of repose, height, and fragment size. The results showed that the ML techniques are useful and reliable methods of predicting rock formation resistive forces based on the rock formation properties. This research is a preliminary step towards developing reliable models for accurate prediction of excavation forces/torques which could potentially enhance hydraulic shovel process automation.

Sep 27, 2021

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

The efficient and effective utilization of hydraulic excavators relies on, among other factors, a better understanding of the formation resistance during the excavation process. Studies on hydraulic shovel excavators have focused on optimizing the digging process by considering the reaction of the boom, stick and bucket, and analyzing the resulting moments at the shovel’s front-end joints. These studies failed to understand resistive forces from a statistical viewpoint. The purpose of this paper is to develop machine-learning models capable of predicting the formation of resistive forces during shovel excavation. The shovel’s excavation was simulated in the PFC 5.0 environment using a typical field-size hydraulic shovel bucket to generate the shovel contact forces required to overcome formation resistance

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a &apos;proof of concept&apos;. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By Carl W. Volz

NORWAY&apos;S metallurgical development, which has extended over many centuries, is intimately associated with that country&apos;s unique topography and climatic conditions. It is a rugged mountainous country, with a most irregular shore line, bordered by thousands of islands forming a natural protection for shipping. There are an endless number of lakes, and innumerable rivers and waterfalls, many fed by glaciers and melting snow. Rainfall is abundant. Though half of the country is north of the Arctic Circle, it is warmed by the Gulf Stream, so that the average temperature is about 45°, or 20° higher than other parts of the world in the same latitude. A sub-

Jan 1, 1935

By Max Hebgen

Within the State of Montana the streams rise in the high mountains at. an elevation of from 5,000 to 8,000 ft. These streams leave the State line both east and west at elevations from 3,500 to 2,400 ft. It is, therefore, apparent. that all these streams have an average fall of 3,000 ft. within the confines of the. State, and many opportunities are presented on all streams. for the development of power, by taking advantage of the natural fall. It is probable that 1,000,000 h. p. can :be developed in the State of Montana. I. NATURAL FEATURES OF STATE AFFECTING POWER DEVELOPMENT. The main. range of the Rocky mountains, forming the Continental Divide, cuts the State of Montana into two parts. The eastern part is drained by the Missouri river and its tributaries, the Madison; Jefferson, Gallatin and Yellowstone, rivers. The western part is drained by tributaries to the Columbia river, the Clarks fork and the Kootenai river. The Clarks fork in turn is formed by the junction of Missoula and Flathead rivers, the latter, draining Flathead lake. The western part of the State. is mountainous and the eastern part is comparatively level. As a natural result the rivers in the western part are capable of generating large amounts of power, while in the eastern part of the State natural power sites are much fewer and farther apart. It also follows that in the mountainous districts large amounts of power are required for the mining industry, while in the eastern part of the State, which is principally devoted to agriculture, power is required in smaller quantities. ?

Jan 8, 1913