Search Documents

By Ashraf M. Eid

Most research dealing with the problem of laterally loaded piles has been the response of individual piles subjected to lateral loads and/or bending moments. However, piles are seldom used individually but are normally constructed in clusters or groups. Little information is available of the effect of pile-soil-pile interaction (PSPI) on the performance of the group. This may be attributed to the difficulty of carrying out full-scale tests. Such tests are prohibitively expensive and require special installations to provide the required large lateral loads. The problem of laterally loaded single piles or pile groups involves the complexity of extending the theoretical solutions to the limits where the actual soil behaves nonlinearly. As the load increases, the elastic soil behavior cannot be adopted for design. Nonlinear soil behavior or the elasto-plastic behavior is evident. This research consists of experimental and theoretical models. The experimental work was conducted on models of free head pile groups in different configurations. The piles were in a sand formation and compared to the behavior of a single pile. The possible factors that influence the group behavior could be visualized. The experimental data was also compared to the widely used theoretical approaches to determine their adequacy. The analytical model makes use of the finite difference approach to calculate the soil non-linearity. A new approach equates the measured ground deflection and maximum bending moments of each row at every load level with the analytical model of single pile. This is the Deflection-Moment Fitting (DMF). The most suitable non-linear soil modulus modes and row contributions could thus be determined. Design of pile groups can be based on data pertaining to soil characteristics of the single pile. Results of the analysis were consistent with other approaches and proved to be adequate for design.

Jan 1, 2005

By Olexandr Gydin

The evolution of grain and dislocation structures during cold deformation of the new steel LH800 of Salzgitter AG is investigated in the frame of this work. The main feature of this material is its ability to air-harden by carbon content of about 0.1%. The initial ferrite structure of the metal provides high plasticity at cold deformation and subsequent heat treatment increases tensile strength approximately two times. Described are results of in-situ tensile tests in the SEM. SEM and TEM analysis of grain and dislocation structures evolution in samples, which have been uniaxially deformed to certain strains, are carried out. After statistical evaluation of results the grain elongation against strain is determined. A microstructure of a deep drawn cup is analyzed by means of SEM. A quantitative evaluation of grain elongation on the different cup zones and comparison of these data with prediction results based on tensile tests are carried out.

Jan 1, 2009

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

During the past 15 years, roof fall rates have fallen dramatically in US coal mines, particularly in regions where the roof is weakest. The remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present a design methodology that builds on and quantifies the basic roof support concepts that have been successful in the USA. The methodology starts by defining three modes of roof support, based on the roof strength relative to the stress level: (1) suspension, where roof bolts mainly provide skin control for strong roof; (2) beam building, where moderate strength roof can be supported by roof bolts alone; and (3) supplemental support for weak roof. Next, a large database of roof fall histories at a number of mines is used to define the approximate boundaries of these three regimes based on the coal mine roof rating and the depth of cover. Finally, guidelines are presented for site-specific design of support systems within each regime. The new computer package, analysis of mine roof support (AMRS), implements the design methodology.

Sep 29, 2020

By J. H. Ahn, J. K. Yoon, Jung-Eui Lee

"A concentration change during grade transition operation in steel thin slab casting is predicted with computer simulation, water model and plant trial. Fluid flow and mixing patterns in various tundish levels and flow rates were analyzed through three-dimensional mathematical modeling. Comparing with water model experiments, a simple, efficient and accurate computational model has been suggested to predict the concentration profile at outlet of tundish. Based on the model, mixing in/below the mold was analyzed considering EMBR. The predicted concentration profiles show good agreements with the measured values. It is found that the lower vortices in the mold are suppressed by the electromagnetic field and the plug-like flow region develops which decreases the intermixing of two different grades of steel and shortens the length of transition region.1. IntroductionContinuous casting is the primary mode of production of semifinished steel products as it offers tremendous advantages in terms of energy savings, increased yield and higher productivity over the traditional ingot casting process. Efforts have to be made constantly to improve the quality of the cast product, reduce costs and thus increase the competitiveness of the steel manufacturer. One way of reducing costs is to reduce the amount of intermixed steel during the grade transition operation.Several different procedures exist to handle the casting of dissimilar grades for the conventional slab casting. Each procedure has its own merits and demerits. In order to choose the best method for a particular operation, there are a lot of researches. In the case of present continuous thin slab casting of POSCO mini mill, the only possible method is to change ladle during the grade transition. Due to the high casting speed (3.8m/min-4.4m/min) it is impossible to change the tundish and due to the thin thickness of slab it is also impossible to insert grade separator."

Jan 1, 2000

By C. Eswaraiah

A drop weight tester (DWT) is designed and fabricated for the purpose of analyzing single particle impact breakage characteristics of different ores. The test results were evaluated through the breakage distributions of different size fractions at five different input energy levels. The breakage parameter, t10 (Narayanan, 1986) is used to represent the degree of size reduction, which is assumed to be representative of the breakage product size distribution obtained from single particle breakage. Representation of breakage distribution with this method consist one more breakage dependent parameter (a). To evaluate the impact breakage characteristic of different ores, a mathematical relationship was established to analyze the dependency of breakage parameters, t10 and a on specific input energy (EIS) or fracture energy (Tavares et al, 1998, Fandrich, 1998), specimen size (?) and Bond?s operating work index (WI0). Mathematical results developed gives adequate model for all ball mill modeling. It can be concluded that the drop weight test method is a useful and practical way of evaluating the impact strengths of various ores and results of which can be used in modeling mills.

Sep 1, 2012

By Jim Buckley, Ryan Sibley, Scott G. Giltner, Thomas Pallua, Joe Schrank, Robert Cidlik

Because of variation in rock type and site conditions, it is important to create site-specific prediction models for peak particle velocity (PPV) and understand instrumentation mounting locations to better interpret the readings provided following blasting operations. The Atlanta Airport is expanding the section of underground tunnels for its Plane Train people mover, and drill and blast operations were determined to be the suitable method of excavation for the project. Extensive work was done to begin creating prediction models and determining levels of concern based on readings from various types of instrumentation. This paper analyzes the effect of close quarters construction blast vibrations and observed frequency spectrum on existing structures with data from 22 different seismographs mounted in various locations and ground conditions.

Dec 1, 2022

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920

By M. F. Ameur, M. Habak, H. Aouici, M. Kenane

Present study interest by aluminium alloy (Al 7175-T5173) drilled without cooling fluid. The influence of the machining parameters (spindle speed and feed rate) on the holes quality was analyzed. Drilling tools are made of carbide (WC); high speed steel (HSS) and TiN coated carbide (WC-Ti).The Experiment design was reinforced by the application of statistical analysis of variance (ANOVA).The results show that the thrust force is influenced principally by the spindle speed and feed rate. Though, both feed rate and tool materials have statistical significance on the surface roughness. In addition, the objective of correlations between spindle speed and feed rate with the evolution of the machining parameters was established. These correlations were obtained by quadratic regression using the response surface methodology. Finally, useful to select optimum values of drilling parameters, that would minimize thrust force, torque, cutting temperature and surface roughness.

Jan 1, 2015

By Jeremy G. Kress

We propose the discrete element method (DEM) as a complimentary alternative to analytical solutions and FEM models for the analysis of pile response. DEM is a novel approach to the engineering design of deep foundations which can be used to provide insight into the mechanics of soil-soil and soil-structure interaction. It is common to use analytical, empirical, and semi-empirical methods to predict pile behavior, where if granular properties, pile length, or load orientation change, then significant adjustments are made in the design sequence. DEM provides a more uniform approach in granular soils. Based on constitutive force-displacement relationships and laws of motion in rigid and elastic bodies, few changes must be made for a wide variety grain types, pile types, embedment, and load orientation. Preliminary results for simulation of a single pile are qualitatively consistent with results from conventional design procedures and also provide significant information not available from other analyses (e.g., local information about interface failure during shear). Importantly, these analyses are portable to a variety of pile types and installation procedures, which may not be the case for empirical approaches. Given consistent increases in computing power and rapid advances in model speed and sophistication, the DEM should prove to be a robust method for design and the analysis of pile response in granular soils.

Jan 1, 2010

By C. B. Piazzarollo

Red Ceramic materials are widely used in Civil Construction in Tropical Countries. However, these materials have high porosity and low mechanical strength. Thus, in order to improve these properties, recycle mineral wastes was incorporated into clay from Campos - RJ, ornamental rock waste, from the gneisses cutting of Cachoeiro - ES, 150 km from Campos. After the addition of up 10% of waste in clay mass, ceramic pieces were produced and subjected to the tests of porosity (P) and flexural strength (FS). The test material contains 53.3% clay and 67% waste slit. The X-ray diffraction identified the presence of kaolinite, quartz and feldspar for the clay and, for the waste, quartz and orthoclase. The results of FS and P showed that the residue influenced, positively, the ceramic piece, with strength gains especially from 920º up to 960°C.

Jan 1, 2015

By B. K. Mishra

Power draw of the mill has been accepted as an indicator of the performance of the mill, yet the problem of predicting power under a given set of mill operating conditions still remains to be solved. In the literature, this problem of predicting power is attributed to a lack of knowledge with regard to the motion of the charge. Here a DEM based model is used to analyze the motion of the charge. The resulting information is used to predict the power draw of the mill. A 16-ft diameter mill is simulated. A factorial design study of the variables-mill speed, lifter configuration and ball size distribution-as independent variables is taken up. The power draw as a response variable is analyzed to establish the best operating condition of the mill.

Jan 1, 1993

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

By R. Karl Zipf

Highwall mining is an important coal mining method. Upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mine Safety and Health Administration (MSHA) accident data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwail miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Trapped highwall miners present a safety hazard to workers during their recovery. Best practices to avoid trapped highwall miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system, Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

Jan 1, 2004

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By Grażyna Dzik, Adam Mirek, Krzysztof Król

The Upper Silesian Coal Basin is located in the area of the Upper Silesian Syncline and belongs to one of the most complex tectonic units in Europe. It occupies 5,650 km2. In 2020, there were 20 hard coal mines operating in the area. Seismological research in this area consists of observation of precursors/symptoms of shock generation and understanding of their effects. Studies (Teisseyre R. 1972, Mutke G. & Stec K. 1997, Stec K. 2007, Dubiński J. & other 2010, Idziak A. 2010) of complex impacts of rock mass provided a background for determining the conditions for the formation of exploitation and regional seismic shocks. Issues related to tectonic and exploitation stresses, successive extraction of coal seams at higher depths, operation in the vicinity of fault zones, often complex geological and organic conditions result in the activation of a discontinuity surface due to stress caused by deformation of rock layers, which, as a result, causes the emergence of strong shocks above 107 J. The article was based on analyses of extraction value, high-energy shocks, both of mining and tectonic-mining (so-called regional shocks) origin, against the background of changing operating conditions, which, as a result, creates an image of periodically changing seismic activity and location of strong shocks. Observation results show that, with an increase in exploitation depth and declining extraction, the number of strong shocks caused by tectonic stress (107 - 109 J) and exploitation stress (≥105 J) has been steadily increasing over the last 25 years.

Apr 26, 2022

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By D. Hulse

"The science of “optimal economic pit design” has been highly refined in the last decades. Even with the proliferation of optimizing and heuristic algorithms exploiting ever faster computers, the most common input is a single block model and a single set of cost assumptions, each of which is an estimate and prone to errors. An analysis of price assumptions produces a suite of nested economic shells, each with its own quantities of ore, waste, grade, and profit, but due to irregularities in the mineralized body, the growth of these shells can be erratic. To control the impact of the errors of the model and cost assumptions when choosing the pit shell for design, graphs of pit shells characteristics, such as stripping ratio, cost per unit of product and profit/ton, can be analyzed to consider points with higher stability, or robust pits. Selection of robust shells for a pit limit and for push backs can help to understand the impact to profit and risk. The robust shells also guide the preferred solution sets for final pit and cutoff optimization. INTRODUCTION “An open pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface.” Optimum Design of Open-Pit Mines, Lerchs, H. and Grossmann, I. Transactions C.I.M. Volume LXVIII 1965. Traditionally an analysis of economic pit shells and sensitivity was performed by varying the input metal price. This was done with both floating cone algorithms as well as early versions of the Lerchs-Grossmann (L-G) algorithm. This gave an indication of the pit sensitivity to price but since other variables also change, some with metal price (perhaps steel and equipment), and some independently (fuel and tires) the understanding of these different pits was restricted. In addition, a run of the program could take hours, making a detailed analysis of small changes unwieldy. The L-G algorithm was programmed by a variety of people and sold as part of commercial mining packages, however it was first and most successfully commercialized by Jeff Whittle in 1984. When Whittle’s 3-D™ was expanded to 4-D the parameterization of the economic inputs was considered and the ability to run a suite of “pit shells” became automatic. The competing NPV Scheduler™ program sold by DataMine™ offers similar pit shell analysis capabilities."

Jan 1, 2018

By N Petropoulos and M J Thurley, E Righetti, M Wimmer

Fragmentation in sublevel caving (SLC) is vitally important. Both gravity flow and any downstream processes are affected. Reasonably coarse fragmentation may lead to larger draw bodies (isolated extraction zones) and hence potentially higher primary ore recovery and depressed/delayed waste rock inflow from above. Fewer flow disturbances are expected by mitigating oversize. In addition, it requires less boulder handling and reduces wear and possible hang-up problems in orepasses. To assess the present-day functionality of large-scale SLC, a multiyear, comprehensive measurement program was initiated. It covers the main elements for SLC, namely blast function, fragmentation and gravity flow. The present paper focuses on fragmentation measurements. An image acquisition system was used to document the drawpoint and the load-haul-dump (LHD) bucket for each mucking cycle. At the beginning, four buckets (about 70 t total) were sieved to validate the results of both 2D and 3D image analysis techniques. The fundamental and specific problems are discussed herein. At the moment, fragmentation of the SLC rings is evaluated using a quick rating system and a 2D fragment delineation software. The results enable a description of fragmentation and its variation during mucking but also – combined with the gravity flow measurements – conclusions on the fragmentation for different parts of the SLC ring. Possible influences on flow disturbances and ore recovery/dilution are investigated. The recent findings allow a better understanding of breakage and flow and support future process improvements.CITATION:Wimmer, M, Nordqvist, A, Righetti, E, Petropoulos, N and Thurley, M J, 2015. Analysis of rock fragmentation and its effect on gravity flow at the Kiruna sublevel caving mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 775–792 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Alejandro Ferrada Vergara, Héctor Espinoza Muñoz

Drilling and blasting stages are considered factors that impact downstream processes significantly and over all the mining business value chain. Adequate control of these processes may represent energy savings in comminution processes. There has historically been a resistance to design change as this implies more drilling and implementation costs due to new technologies in explosives, which added value is difficult to quantify.

Jan 1, 2016

By Liane J. Terrill

Rockbolt failures at the Waste Isolation Pilot Plant have been recorded since 1990 and are categorized in terms of mode of failure. The failures are evaluated in terms of physical location of installation within the mine, local excavation geometry and stratigraphy, proximity to other excavations or shafts, and excavation age. The database of failures has revealed discrete areas of the mine containing relatively large numbers of failures. The results of metallurgical analyses and standard rockbolt load testing have generally been in agreement with the in situ evaluations.

Jan 1, 1995