Search Documents

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

"Longwall shearers are widely employed in underground coal mines. The reliability of such machine has significant importance for successful mining operations. This paper aims at studying reliability of a longwall shearer using failure data recorded for a year. Data was pre-processed, sorted and selected for analysis. Selected data is then examined using statistical models. Distribution fitting of time-between-failure (TBF) and time-to-repair (TTR) are accomplished using three different models. Goodness-of-fit criteria is used to ascertain the best fitting model. Reliability in terms of mean-time-between-failure (MTBF), and mean-time-to-repair (MTTR) are calculated using the model which best represents the failure data. Exponential distribution best represents the time between failure and lognormal distribution the time to repair data. A well-known risk management technique Failure Mode Effect and Criticality Analysis is used to evaluate the critical breakdowns. Critical system/parts, experiencing regular failures is delineated based on this analysis. INTRODUCTION Mining is a capital intensive process, and huge monetary investment is required to develop and operate a mining project. Heavy and expensive equipment’s are employed in development and operation of these projects. In order to ensure timely completion of set milestones, it is mandatory that equipment’s perform their required task productively. Delays are not unusual owing to breakdown of these equipment’s. Breakdown or failure experienced by any of the equipment pose heavy financial burden. Moreover, frequent times, companies have to employ and dedicate additional resources to make up for such delays. Delays in project is not only detrimental to company’s image in market, but it also interrupts customer commitments. Mines having history of not fulfilling their promise usually get lower commodity price. Penalties are also imposed on the companies defaulting its obligations. Especially, in today’s world where competition among the companies are growing, success means keeping up the commitments in a timely manner. Heavy machinery and equipment are instrumental in success of any project. These machinery and equipment’s have to reliable in a sense that they can perform the set task in given time period. Reliability of these equipment plays a pivotal role in success of any project. The reliability analysis of mining equipment has long history. Many researchers have applied different statistical models for analyzing the reliability of mining machines (Samanta, Sarkar [1]. Kumar and Klefsjö [2] demonstrated the use of the power law process model for reliability assessments of repairable mining machines. Barabady and Kumar [3] performed the reliability analysis from failure data of the crushing plants."

Jan 1, 2018

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs. Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs.Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By Amit Srivastava, Monica Malhotra

In a congested city or urban area, so called “lifeline of the city”, i.e. Gas, Electricity, telecommunication, as well as other utilities or facilities are supplied or transported underground through buried pipes or utility tunnel. Sometimes these buried pipes or utility tunnels are deep underground and interfere with the foundation of new structure. It is highly probable that a pile foundation is placed near an existing underground buried pipe or utilities tunnel and may influence its load bearing capacity. Hence, estimation of reduce load bearing capacity of the pile foundation placed near the existing buried conduit or utility tunnel is a complex soil-buried structure interaction problem. It is further complicated owing to uncertainty in estimation of geotechnical parameters of foundation soil due to measurement and testing errors, inherent soil variability and model transation. Under such circumstances, load bearing capacity is best assessed in probabilistic framework or through reliability analysis. The present study demonstrates how concept of response surface method (RSM) in conjunction with Numerical Analysis and First Order Second Moment (FOSM) methods can be combined to per the reliability analysis. The study answers the following question “reliability in reduction in the load bearing capacity of single pile placed near the existing underground pipe or utilities tunnel”. It is demonstrated that the approach provides first hand ination on the reduction in the load bearing capacity and then estimate the reliability of that estimation in terms of an index called Reliability Index (). Such preliminary investigation can be useful for advocating the detailed analysis as well as in the decision making for relocation of pile foundation.

Sep 1, 2022

By T. R. Kostecki

"Instrumented rock bolts are effective tools for assessing the reinforcement and condition of immediate roofs; however, instrumentation can have relatively high costs, which can be justified by high reliability and repeatable and representative data measurements. The instrument’s durability and operational life are of great importance, along with accuracy, applicability, and usefulness. This paper develops reliability models for three instrumentation technologies used in slotted rebar, drawing data from studies at five underground coal mines. Three case studies demonstrate instrument applicability and usefulness. Finally, two types of instrumented rock bolts are used to determine the direction of bend and maximum bending strain. RÉSUMÉ Les boulons d’ancrage instrumentés sont des outils performants qui permettent d’évaluer la consolidation et la condition des toits immédiats. L’instrumentation peut cependant se révéler très onéreuse, des coûts qui se justifient par sa fiabilité élevée ainsi que par des mesures de données reproductibles et représentatives. La durabilité de l’instrument et sa durée de vie opérationnelle sont très importantes, de même que son exactitude, son applicabilité et son utilité. En s’appuyant sur des données issues d’études menées dans cinq mines de charbon souterraines, cet article développe des modèles de fiabilité pour trois technologies d’instrumentation utilisées pour des barres d’armature nervurées. Trois études de cas démontrent l’applicabilité de l’instrument et son utilité. Enfin, deux types de boulons d’ancrage instrumentés sont utilisés pour déterminer la direction de la flexion et la contrainte de flexion maximale.INTRODUCTION Using instrumented rock bolts to monitor strain changes in a rock bolt array allows engineers to understand the per-formance and effectiveness of the rock reinforcement system and the response of the rock mass to such support; however, instrumentation remains a niche solution for solving complex ground-control problems—particularly for underground coal mines, which is where they are needed most. From 2000 to 2016, fall-of-ground fatalities still accounted for an average of approximately 30% of the total annual underground coal mine fatalities in the United States alone (United States Department of Labor, 2018). These tools would also be useful for deep hard-rock mining conditions. The main reasons for the lack of widespread use are not only cost but also accuracy, applicability, implementation procedures, intrinsic permissibility, and reliability (Peng, 2015). As a result, measurements of coal mine roof behaviour using instrumented rock bolts are quite scarce, not widely published, or inadequately presented to provide a seamless understanding of a roof’s response to support."

Jan 1, 2018

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By E. B. Wilson

"Although the Operations Research technique of Reliability Theory has been applied with marked success in many fields, including the Apollo spaceship programs, the concept of reliability has not been generally adopted in mining and other heavy industries. Of course, reliability, or the probability that a system will be able to operate without a failure for a given interval of time, does not require the same emphasis in mining as in the aerospace industries. Nevertheless, certain aspects of Reliability Theory can be followed advantageously. For example, reliability calculations can determine the best time to overhaul and whether to retain stand-by units.The usefulness of the pseudo-operations research technique known as Replacement Theory is more readily re-cognized by the maintenance engineers in mining and other heavy industries. One of the least complex models enables the optimum Lifetime of an asset to be determined."

Jan 1, 1970

By M. T. Davisson

Pile compression load capacity prediction methods are divided into four categories for purposes of discussing their reliability compared to static load test results. The categories considered are: 1) static analysis, 2) driving formulas, 3) wave equation analysis, and 4) dynamic measurement and analysis. It is concluded that any method of static analysis that works for the geological deposit in question may be satisfactory. However, any given method can be quite wrong when applied to other deposits of soil that are different in terms of their engineering and geological characteristics. Dynamic formulas are found to be theoretically unjustifiable. The ready availability of the wave equation analysis for microcomputers eliminates the need to utilize dynamic formulas. The wave equation analysis is found to be the best analytical method for making predictions both for design and for construction control. Dynamic methods of measurement and analysis are found useful, but have limitations that have caused troubles on many projects. Two case histories are presented that show the limitations of dynamic measurement and analysis, and of the wave equation analysis. Soil deposits exist that defeat both the wave equation and dynamic measurement techniques; static load tests are currently the only method of proving the load capacity of piles in such soils.

Jan 1, 1991

By Konstantinos Komnitsas, Evangelos Petrakis, Emmanouil Varouchakis

During the modeling of grinding systems, population balance modeling (PBM) which considers a constant breakage rate has been widely used over the past years. However, in some cases, PBM exhibited some limitations, and time-dependent approaches have been developed. Recently, a non-linear framework which considers the traditional linear theory of the PBM as a partial case was introduced, thus allowing the estimation of product particle size distribution in relation to grinding time or the specific energy input to the mill. In the proposed model the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (RR) distribution. Besides, the adaptability and reliability of the prediction model are among others dependent upon the operating conditions of the mill and the adjustment of the RR distribution to the experimental data. In this study, a series of grinding tests were performed using marble as test material, and the adaptability of the non-linear model was investigated using three loads of single size media, i.e., 40, 25.4, and 12.7 mm. The results indicate that the proposed model enables a more accurate analysis of grinding, compared to PBM, for different operating conditions.

Jun 24, 2023

By Lifeng Li, Jhon Silva-Castro

In a previous work, the authors analyzed the overlapping probability of two adjacent charges in a single hole for pyrotechnic and electronic detonators. This document extends such work to a complete mine blast where more than two holes are detonated. In a mine blast, all the blast holes are connected as a network by detonators to follow a given initiation sequence. Such initiation sequence’s performance is based on the adequate timing between charges in the mine blast. The analysis of the reliability of a mine blast based on the timing between charges and the initiation type is presented in this document. For a long-run time and under proposed operating conditions, the reliability of the mine blast can be analyzed based on the network which is treated as a system. The failure of the system is defined as no success between any two delays charges either in a single hole or in between two holes.

Jan 1, 2016

By Ernesto Furtado de Mello Neto, Eliezer Thuler, Claudio Vano Nunes, Carlos Alberto Cristofari

The Brazilian steel industry is dealing an adverse scenario with direct competition from global emerging markets. In this scenario, the need to improve asset operational performance, makes complex studies involving technical knowledge and asset life behavior, become important tools to support companies strategic accomplish. These studies allow consider performance, costs and operational risks relationship in the decision make process. The Asset Management approach support these studies in order to observe the whole asset life cycle, understand value chain through all company process and optimize the asset economic life. In this context, the present technical work has the purpose to support asset management decision making regarding ArcelorMittal Vega cold rolling drive motors, through the motors fail behavior modelling and estimated the risks involved in asset management decision. Through the Reliability, Availability and Mantenability (RAM) analysis, simulations were performed considering the failure, repair cost data and investments to build options to mitigate the operational risks.

Oct 9, 2019

By Snehamoy Chatterjee, Sanjay Kumar Palei, Smarak Das

Machine manufacturers’ recommendations on maintenance strategies of capital-intensive draglines are not always based on real data and therefore lead to losses from downtime. This paper proposes a preventive maintenance strategy for a dragline deployed in an opencast coal mine based on reliability-centered maintenance and failure-mode-effects analysis using real operational data. Reliability-centered maintenance replaced a cluster of critical failure components of the dragline while satisfying two specific conditions: (i) the components should be replaced at the earliest mean time to failure (MTTF) within the group and (ii) the time taken to replace all the parts should be equivalent to the maximum downtime within the group. Estimated threshold weightage factor identified twenty-six critical failure components for the preventive maintenance strategy, and clustering of components divided them into nine groups. In a group, the loss that is expected to occur by replacing some of the components before their failure, and the gain by reducing the overall maintenance downtime, has been explained through a cost-benefit analysis. The total net profit generated is calculated as US$200,178. This clustering activity also led to a reduction of annual downtime by 231 h, whose approximate market price as equivalent coal production costs $295,365.

May 28, 2020

By L. W. Kempf, K. R. VanHorn

PLASTIC deformation of most commercial metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful estimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. DETERMINATION OF RESIDUAL STRESSES The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.1 Fig. I reproduces some of the data

Jan 1, 1941

WaihiÆs Cornish Pumphouse is located on the edge of town in a dynamic and changeable area where history affects the future. As in any successful project, ingenuity and team work have been significant factors in the planning and implementation of the buildingÆs relocation.   Work around the Pumphouse site commenced circa 1900 with preparation to sink the No 5 shaft. Construction of the pumphouse and the steam driven C pump was completed by 1904 with hints of what was to come evident in 1905 as the No5 Shaft collar had sunk 350mm in four years. By 1907 surface cracking developed over the Milking Cow cave area and in 1913 200 mm was cut off the main pumping rod as the ground was sinking at a rate of 25 mm per year.   In 1913 ground around No 6 shaft had subsided 600 mm.It was also the end of an era as steam gave way to hydroelectricity and electric pumps replaced the C Pump. C Pump was maintained as a backup from 1913 to 1929 and then finally scrapped. 25 years of underground caving operations removed approximately 400 000 cubic metres of ore leaving a 7 ha collapse crater that eventually became known as the mine lake.   On the edge of town a tension zone over the Royal Lode began to develop 50 m diameter chimney collapses as large scale blocks relaxed into unfilled stopes in the old Martha underground mine. After the 1999 collapse part of the main street was closed and after the 2001 collapse Hazard Zones were declared, more streets closed and areas evacuated and retired from residential use.   By 1984 the Pumphouse has approximately one degree of tilt and in 2002 tilt on the Pumphouse accelerated briefly and then settled down. Tilt accelerated again late in 2004 and a scoping study was initiated to define protection options for the pumphouse. The Martha Mining Licence requires Newmont to 'Take whatever precautions are necessary to protect the old Cornish Pumphouse adjacent to No5 shaft' and viable solutions needed to found.   Any work on the Pumphouse comes standard with a wide range of stakeholders, governing agencies and legal framework to consider. Land Information New Zealand (LINZ) is owner and administrator of the pumphouse.

Jan 1, 2006

By G G. Suffel

T HESE remarks on the occurrence of strata-bound massive sulphide deposits are submitted be-cause the writer recently visited the principal Cyprus deposits (in January, 1965) and has also a back-ground of many years spent largely in detailed observation and map-ping of the Horne and Amulet ore-bodies, now largely inaccessible. They are particularly related to the Symposium papers (September Bulletin) by Hutchinson and by Roscoe. Some comments are offered on the cupriferous pyrite deposits of Cyprus. As the writer is currently reviewing the published literature on the related deposits in Turkey, a brief account of some characteristic Anatolian sulphide occurrences is given. The discussion is closed with some thoughts on the relationship between these Mediterranean sulphide deposits and those of northwestern Quebec and the Superior province in general. The geology of Cyprus, as it relates to the sulphide deposits, is well summarized by Hutchinson (1965). After visiting Mavrovouni, Skouriotissa and Limni and after much thought on the possible ge-nesis of these ores, it seems quite logical to me that he is right. They are indeed closely related to late-stage submarine volcanism.

Jan 1, 1965

By G. W. Brooks

This short article is quite different to the general run of papers that are presented to the Institute, but no apology is offered because I consider that first-aid and mine-rescue work are of equal importance to many other subjects that are dealt with in our Transactions. Members of the Institute should be as much interested in the safety of persons engaged in the mining industry as they are in the practical methods of modern mining. We must not only do our best to conserve life and property by adopting every known device to that end, but we must also prepare ourselves so that we may take prompt and effective action when life is in danger, or when property is subject to loss. The need for such preparation in Alberta is perhaps greater than in most places where mining is carried on, and we must spare no effort to assemble at every mine men who are well trained in first-aid and mine-rescue work. The large area over which the mines are distributed renders central training stations out of the question, hence the need for local rescue-teams. Hospitals with skilled staffs, close enough to the mines to be convenient, also seem to be out of the question; therefore the greater need of a high standard of first-aid training for the people in our mining camps. The Government mine-rescue cars are supplied with the equipment necessary for training persons in this essential work and also for dealing with disasters should they occur. The question then arises: are there a sufficient number of men who are trained ? If so we can rest assured that what is possible to be done will be done. But if a sufficient number of trained men are not available much loss of life and damage to property is likely to result.

Jan 1, 1925

By Edmund C. Pechin

I REGRET that I am unable to present this subject in definite form and detail. All I shall attempt at this meeting is to lay before you some curious facts, the bearings and explanations of which must be reserved for future consideration. I hope before the next meeting to have carried experiments far enough to furnish a more important contribution to the science of iron metallurgy. The Wickersham process consists in the introduction into the molten metal, as it runs from the furnace, of air from the hot blast. Mr. Samuel Wickersham is the originator of the plan, as applied in practice, although Mr. Martien had the idea a long time ago, and, I believe, .went to England about it. But at that time Mr. Bessemer was coming before the public with his invention, which engrossed the attention of iron-masters, and Mr. Martien accomplished nothing. The principal difficulty in our experiments at Dunbar was to get a practicable runner or trough, through which the molten metal should pass, and in which it should be exposed to the action of the blast. The runner we used was ten feet long, and perforated on the sides to permit the entrance of the air-currents. When we used a cast-iron and fire-clay runner, the heat was so great that before we were more than half done with a run, the lower part of the runner was melted, and we had a magnificent Fourth of July display of fireworks until the blast was shut off. We had to abandon fire clay. The runner with which we have had the best success ,is made of wrought-iron tubes, 2 1/2 inches in diameter, attached to a wrought-iron frame, and lined with a mixture of crushed conglomerate (quartz) and a little fire clay to give it cohesion. The wrought-iron shell curves inward over the upper edges, so as to catch and throw back into the current the flying sparks and particles of metal thrown out by ebullition. With this we have been able to run 12 to 14 tons at a heat with great ease. Mr. Wickersham has since prepared this material (pounded quartz) into a shaped brick or tile, with the necessary perforations for the passage of the air, which promises to answer every requirement for steady working. As regards the improvement in the quality of the iron, there seems to be no question. A large number of practical tests were made in

Jan 1, 1873

By Sandra M. Stash

An integrated copper production complex includes mining, milling and smelting facilities which are usually at or near a common site, and sized to complement one another in capacity. There may also be an electrolytic retlnery serving the complex, but not always totally dedicated to its production. Mines and mills without co-owned smelters are not usually considered integrated. The first marketable product of an integrated complex is blister, or in some cases electrolytically refined copper. The nature of integrated operation brings together all of the environmental issues associated with copper production, but currently operating and newly planned facilities are required to anticipate these issues and meet stringent regulations. Older complexes, however, may have legacies of 50 or more years of operation unencumbered by current levels of environmental strictures: nevertheless, they must be remediated. Using examples from closure and remediation of the mining and mineral processing facilities in the Upper Clark Fork River Basin of Montana, the authors review some of the problems encountered since CERCLA's1 enactment in 1980, and the solutions to those problems, bearing in mind that not all of the problems and solutions were technical. Much has been written about the mines of Butte -the "Richest Hill on Earth" as it was known in its day and the mills, smelters and refineries they spawned. These facilities comprised an archetype of the integrated copper complex: from ore to metal in facilities serving and depending on one another. Many great stories of technological innovations and business triumphs have been told about Butte and Anaconda's mining history and the place The Anaconda Company occupies in that history. However, relatively little has been written about the final days: 25 years during which the once-great complex was closed, and the remnants of past glories were remediated after nearly a century of operation. This paper offers some insights from the real world affecting similar complexes still operating, and, hopefully, lessons for others just starting down the path to final closure.

Jan 1, 2003

By R. M. Taylor

Lime addition to acid mine drainage (AMD) leads to precipitation, predominantly of metal hydroxides and calcium sulfate, and is the benchmark for remediation by precipitation. Geo2 Limited of Melbourne, Australia has developed and patented a novel alternative precipitation scheme based on the formation of mixed valency, M(I1)-M(III), hydroxide sulfate salts. When the composition of AMD is appropriate, the Green Precipitate Process provides a useful and more effective alternative to conventional liming. The characteristics and utility of the Green Precipitate Process are described in terms of the underlying chemistry, and a case study where the Green Precipitate process outperforms conventional liming. A mobile pilot pipe reactor rig which was built by Geo2 to demonstrate the process, and used successfully in both Australia and the United States, is described.

Jan 1, 1998