Search Documents

By Stephen P. Quin

One of the most prospective undeveloped greenstone belts in Canada, the Hope Bay greenstone belt extends over 80km in a north-south direction and is between 7 and 20km wide. The belt lies on the arctic coast and comprises mafic meta-volcanic and meta-sedimentary rocks that are bounded by Archean granite intrusives and gneisses. The greenstone package has been deformed during multiple events and is transected by major northsouth trending shear zones that appear to exert a significant control on the localization of mineralization. The Hope Bay belt contains a number of significant gold deposits hosted in a typical Archean greenstone belt and which occur in several geologic settings, including shear-hosted, lode-style and breccia-associated. Combined, the deposits host a measured and indicated resource of 1.6 million oz of gold averaging 15.7 g/t plus an inferred resource of 2.7 million oz of gold averaging 12.3 g/t. All deposits remain open to expansion. Exploration in the period 2000-2002 by Miramar includes more than 110,000m of drilling to more fully define the nature of the known deposits, while regional exploration has focused on identifying and evaluating new targets. In carrying out its programs, Miramar uses a number of techniques to improve its chances of exploration success. Activity in 2003 includes 43,000m of drilling focused on expanding resources in the Madrid area, testing the Boston deposit at depth and continuing the hunt for more discoveries. Meanwhile Miramar is advancing one of the deposits towards a production decision, based on a low capital, high return development scenario.

May 1, 2003

By L. E. Kun, R. O. Oelofsen, E. J. J. van Vuuren

High-rate floc-blanket clarification of gold pregnant rotary filtrate was introduced at the Vaal Reefs South gold plant of the Anglo American Corporation during February 1978. A. daily 12 000 to 15 000 t of filtrate, with an average suspended-solids concentration of 350 mg/I, is continuously clarified to a concentration of less than 2S mg/I of suspended solids in a modified plant pachuca (10 m in diameter) at throughput rates of 7,7 to 8,5 ma/m2.h by the addition of 5 g/t of ferric chloride inorganic coagulant and 0,2 g/t of Superfloc NI00 flocculant. The pachuca overflow is then clarified further in seven Stellar candle pressure filters of 54,S m2 surface area to under 5 mg/I of suspended solids. The combined clarification cost when the hopper clarifier is used in conjunction with the Stellar filters is R0,0032 per ton of liquid treated, which is approximately 60 per cent lower than the cost of Stellar filtration on its own. The savings are mainly due to the reduced use of filter pre-coat, the consumption of which has dropped by 70 per cent since the introduction of hopper clarification.

Jan 1, 1979

By A. G. Ramsay, P. G. Kahles, L. E. Kun

A method for the clarification of uranium pregnant solutions using a high-rate floc blanket was developed from laboratory scale through pilot-plant testing to full-scale production by the Anglo American Research laboratories. A two-stage clarification process (hopper plus leaf) was commissioned at the Western Deep levels uranium plant in October 1980. The high efficiency of the hopper clarification permitted its use on its own. The leaf clarifiers were therefore taken out of service in September 1981, since when the secondary clarification is achieved by further unaided gravity settling in the semi-clarified and clarified pregnant-solution storage tanks. As a result, a daily 12000 to 17000 t of countercurrent-decantation overflow with a suspended-solids concentration of 500 to 600 mg/I is continuously clarified to a suspended-solids concentration of less than 30 mg/I. Secondary gravity settling reduces the suspendedsolids concentration to under 20 mg/I. The cost of the single-stage hopper-clarification process is RO,O020per ton of liquid treated. The removal of the leaf clarifiers from the circuit resulted in an approximate visible saving of RI00000 per annum.

Jan 1, 1983

By F. N. Lewis

HOPPERS may be divided into three classes accord-ing ing to type, namely; round, suspension, and square or rectangular. The round hopper is the most simple of the three and is the most easily understood by laymen. The bursting pressure in these hoppers is resisted by the shell as a round tank resists the pressure of water. They are perfectly stable as long as they retain their cylindrical shape. In holding water or other liquids the pressure on the sides is always the same, but with ore this is seldom true. These round hoppers for ore are usually filled from one side and frequently drawn off from the opposite side. A considerable amount of fine material is deposited on the side of filling, while the coarse particles run over to the far side. This con-dition of filling causes the ore to flow out unevenly, sometimes drawing out completely on one side. After a time the remaining ore breaks down and the shock of this falling ore, sometimes many tons, is very severe and has a tendency to distort the hopper from its true shape; consequently a round hopper holding ore should be stiffened to resist such shocks as this. For these reasons round hoppers have never been popular with engineers for holding ore. They also have a trait of welling. up worse than the square hoppers. I have known of round hoppers holding fine ore, 25 ft. diam-eter, that had a tendency to well up until there was ,only a round hole about 6 ft. diameter leading to the gate. The suspension or catenary type of hopper is well adapted to conditions requiring only small capacities. The selection of this type of hopper should be done with considerable care. The theory of the design is that the loads are carried entirely in tension in the bottom plate, just as a hammock carries a load, and it must be remembered that the bottoms of these hoppers are con-stantly changing form with the changing loads. Take a hammock, for example, if a person stands up in it, the bottom goes down and the sides approach a straight line; if the person lies down then the bottom comes up and the sides go down. It is this constant changing of the form that has a tendency to break the connections.

Jan 7, 1928

By Duane A. Smith

Horace Tabor. No 19th century Colorado mining man is better known but, unfortunately, probably less understood. He is little appreciated for his significant contributions to the industry and the state. A century ago, Tabor was headline news. The legend today, however, has become so all pervasive and so interwoven with fact that the two are hard to separate. For example, he never told Baby Doe on his death bed to hang on to the Matchless mine. Yet this has emerged as staple Tabor fare. So much attention has been focused on his matrimonial triangle that it overshadows the man. Symbol of mining's reward Tabor traveled west in the 1859 Pike's Peak gold rush. In the next generation, he came to symbolize the rewards mining might lavish on an individual. The Leadville Daily Herald (Sept. 10, 1882) could write, without exaggeration, that "the extent which the mining industry of Colorado is under obligation to Tabor cannot be easily estimated - what he has done for Leadville and Denver is patent to all." It had not come easily, nor had Tabor started out a success. His early placer mining at Payne's Bar, near present-day Idaho Springs, CO, had turned no fortune. So in 1860, he, his wife Augusta, and son went south to Colorado City, then over Ute Pass and up the Arkansas Valley to Oro City. Arriving soon after the initial discovery, Tabor staked a good claim. With a sharp eye, he and Augusta broadened their base by establishing a store. Both mining and business would pay dividends in the following years. By the season's end, though, Oro City was already declining. Always on the lookout for a richer district, Tabor and his family moved the next year across the mountains to promising Buckskin Joe. The familiar pattern followed, with the store and post office being the center of their attention. Mining investment and management now replaced the earlier physical panning and sluice operating. Seven years later, the Tabors abandoned Buckskin Joe and returned to Oro City. It had moved up California Gulch to be near the district's best mine, the Printer Boy. Middle class was not enough Middle class respectability, plus a steady income, was the Tabor's by the 1870s; fine as far as it went. But it proved far from the fortune Horace had always been seeking. Oro City languished in the backwash of Colorado mining and Tabor seemed like many men who had drifted around the Territory following the ebb and flow of mining. His faithful wife Augusta had been a steady factor in the success the family achieved. She helped year after year to operate the store and post office. Not simply the happy-go-lucky individual he has often been portrayed, Tabor was a hard working businessman/mine owner. An R. G. Dun and Company agent evaluated him in 1876 "Net worth $23,200. Is a very shrewd businessman and not liable to lose money, has a good chance to make money as he had no competition." Leadville: Tabor's silverlined-fortune After all those years on the Colorado mining frontier, in 1877, Lake County's wealthiest and most respected merchant made another move. It was short in distance, only 4 km (2.5 miles) down California Gulch, then a little north to a new mining camp. This new camp, soon named Leadville, gave birth to the Tabor fortune and legend. Middle-aged (Horace was 47), the Tabors once more set up their general store and found themselves in the midst of the open¬ing of a new district. This time silver beckoned and not the gold that had brought them West 18 years before.

Jan 1, 1989

H ORACE VAUGHN WINCHELL was born at Galesburg, Michigan, Nov. 1, 1865, and died at Los Angeles, California, on July 28th of this year, at the age of fifty-seven. Mr. Winchell was one of the conspicuous geologists of his time. It may fairly be said that he was a geologist born and reared. His father, N. H. Winchell, was professor of geology at the University of Minnesota; his uncle, Alexander Winchell, was professor of geology at the University of Michigan. Under both of them Horace studied, graduat-ing at the University of Michigan in 1889. Mr. Winchell at once began that active life in the field which he followed for 34 years and until his death. The first years of his professional life were largely spent in the study of the iron ranges of Min-nesota. In 1898, he re-moved to Butte and became geologist in charge of the geological depart-ment of the Anaconda Copper Mining Co. and allied companies. There he remained for eight years. This period covered the trying days of the mining controversies be-tween the Anaconda and associated companies and the Heinze interests, and it fell to Mr. Winchell to direct the geological studies and development in connec-tion with that litigation. Recognizing the importance of careful geological study in the practical operation of mines, he organized and developed the splendid geological department of the Anaconda Copper Mining Co. This was one of his greatest contributions to the mining industry. Probably no mining company has attached the impor-tance to geological study and continuity of geological mapping in connection with mining operations that the Anaconda company has. It has given broad authority to its geological department and the development of its mines is under the direction of its geologists. The broad vision of Mr. Winchell was responsible for the adoption of this policy, one which is being profitably employed by many other organizations.

Jan 9, 1923

By I. R. Muirhead, A. L. Craven

The trend in mining thermal coal is only to mine coal with the lowest sulphur content. In many coal seams, bands of coal with high sulphur content are often present, generally occurring either at the roof or floor level. Methods of selective mining are, therefore, necessary to recover only the low sulphur coal. This paper examines the methods currently in use in mines and the alternative methods that are able or have potential to offer control of shearers and continuous miners where greater thicknesses of coal have to be left in the roof and floor. These alternative methods rely on such characteristics as neutron gamma radiation; electromagnetic waves; vibration; infrared; infrared; optical; pick force; X-ray fluorescence; conductivity; gyroscopes and laser systems.

Jan 1, 2000

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

Preliminary design is underway for a new Southern Nevada Water Authority (SNWA) project that will ensure one of America’s most reliable water systems by providing continued, reliable water service to existing and future customers. The Horizon Lateral is a $1.6 billion water transmission pipeline that includes 7–10 miles of 108-inch finished diameter rock and soft-ground tunnels. The tunnels will traverse volcanic rock in or around the McCullough Mountain Range and the surrounding alluvial basin. The tunneling community will find relevance in hearing about this critical infrastructure project from a leading wholesale water utility owner with a proven track record for on-time, collaborative projects.

Dec 1, 2022

By W. N. Poundstone, P. C. Thakur

Introduction Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1958 at the Humphrey mine of Consolidation Coal Co. for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for several years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300 to 600 m, with reasonably precise directional control and within practical cost limits (Spindler and Poundstone, 1960). Mining Research Division of Conoco Inc., the parent company of Consolidation Coal Co., began a research program in the early 1970s to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary results of this research have already been published (Thakur and Davis, 1977). To date nearly 4.5 km of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: • The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3% in course of two to three months from original values of nearly 0.95%. • The methane concentration in the section return reduced to 50% of its original value immediately after the boreholes were completed, indicating a capture ratio of 50%. • The total methane emission in the section (rib and face emission plus the borehole production) did not increase but rather gradually declined with time. • Initial production from 300 m deep boreholes in the Pittsburgh seam varied from 3 m3/min to 6 m3/min but then slowly declined as workings advanced inby of the drill site (well head) exposing a larger surface area parallel to the borehole. Encouraged by these results, it was decided to design a horizontal drilling system that would be mobile and compatible with other face equipment. A mobile horizontal drill can be divided into three subsystems: the drill rig, the drill bit guidance system, and borehole surveying instruments. The drill rig provides the thrust and torque necessary to drill 75- to 100-mm diam holes up to 600 m deep and contains the mud circulation and gas cuttings separation systems. The drill bit guidance system guides the bit up, down, left, or right as desired. Borehole surveying instruments measure the pitch, roll, and azimuth of the borehole assembly. Additionally, it also indicates the thickness of coal between the borehole and the roof or floor of the coal seam. Thus, it becomes a powerful tool for locating the presence of faults, clay veins, sand channels, and the thickness of coal seam in advance of mining. In recent years, many other potential uses of horizontal boreholes have come to light, such as in situ gasification, longwall blasting, improved auger mining, and oil and gas production from shallow deposits. The purpose of this paper is to describe the hardware and procedure for drilling deep horizontal holes. The Drilling Rig [Figures 1 and 2] show the two components of the mobile drilling rig: the drill unit and the auxiliary unit. The equipment (except for the chassis) was designed by Conoco Inc. and fabricated by J. H. Fletcher and Co. of Huntington, WV. The drill unit. It is mounted on a four-wheel drive chassis driven by two Staffa hydraulic motors with chains. The tires are 369 X 457 mm in size and provide a ground clearance of 305 mm. The prime mover is a 30-kw explosion-proof electric motor which is used only for tramming. Once the unit is Crammed to the drill site, electric power is disconnected and hydraulic power from the auxiliary unit is turned on. Four floor jacks are used to level the machine and raise the drill head to the desired level. Two 5-t telescopic hydraulic props, one on each side, anchor the drill unit to the roof. The drill unit houses the feed carriage, the drilling console, 300 m of 3-m-long NQ, drill rods, and the electric cable reel for instruments. The feed carriage is mounted more or less centrally, has a feed of 3.3 m, and can swing laterally by ± 17°. It can also sump forward by 1.2 m. The drill head has a "through" chuck such that drill pipes can be fed from the side or back end. General specifications of the feed carriage are: [ ] The auxiliary unit. The chassis for the auxiliary unit is identical to the drill unit but the prime movers are two 30-kW explosion proof electric motors. It is equipped with a methane detector- activated switch so that power will be cut off at a preset methane concentration in the air. No anchoring props are needed for this unit. The auxiliary unit houses the hydraulic power pack, the water (mud) circulating pump, control boxes for electric motors, a trailing cable spool, and a steel tank which serves for water storage and closed-loop separation of drill cuttings and gas.

Jan 1, 1981

We outline a first version of an ambitious goal: The world's first horizontal (matrix-independent) generic sampling standard. The specific needs and requirements are overwhelming, as all the world's analytical standards follow strict matrix or material type classification pigeonholes, leading to a plethora of analytical standards. One could rightly expect a similar multiplication regarding sampling standards, yet the singular HORIZONTAL is aimed at being truly generic. Also the existing style of standards writing is cumbersome and partly contradictory. The current work is presently being pursued in CEN and European Union standardisation regimens, for which reason full disclosure and publication is not allowed. Respecting this constraint, we unofficially present selected key issues involved in developing HORIZONTAL: The objective and scope of a horizontal sampling standard is to delineate the minimum set of principles and procedures needed to guarantee documented representative sampling for all types of materials. The horizontal standard is designed for two types of use: 1. auditing/assessing/ improving the reliability of an existing sampling procedure, and 2. design and implementation of a new sampling procedure (new lot type). The principles in this standard are all derived from the Theory of Sampling (TOS), but the standard is far from a mere collection of TOS principles. Representativeness is a characteristic of the sampling process, not of samples themselves. For practical purposes, the horizontal standard follows the fundamental distinction between 'stationary lots' (0-D, 2-D, 3-D lots) and 'dynamic lots' (within TOS aka process sampling - including extended, non-moving 1-D lots). TOS' principles of 'correctness' must never be broken at any stage, lest representativeness is irretrievably lost. The horizontal standard is not written in the mandatory fashion for legally binding matrix-specific standards, eg ISO - for the present overarching purpose a different style had to be developed. The standard must be immediately understandable in full, which merits special demands, eg extensive use of didactic illustrations. HORIZONTAL introduces an all-inclusive sampling variability measure, Relative Sampling Variance (RSV) which is for sampling of stationary lots as variographics is for process sampling - RSV is to be used as a quality criterion for any stationary sampling procedure as applied to a specific heterogeneity (lot/material). The target for this standard is all individuals, companies, organisations and regulatory bodies who are responsible for sampling: technicians, process engineers, laboratory personal, academic and industrial scientists as well as project leaders, technical managers/directors and top managers. Based on current R&D we illustrate the principles promulgated by HORIZONTAL with cases from exploration and mining of minerals commodities, a Finnsh 'Autosampler' at work in the mining context (RSV) as well as sampling equipment for use in the cement and mineral commodities industries. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Mar 1, 2010

By J. D. Potts

Installation of a horizontal air blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong coanda effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector to bailing airflow ratio, and a 5.1-cm (2-in) gap between the shroud and ground. The shelf was 15.2-cm (6-in) wide and located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2009

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By L. Morgan, M. Le Roux, Q. P. Campbell

Dry coal processing is becoming increasingly favoured as a fine coal beneficiation technique. The decline in suitable good-quality coal, as well as the ongoing decrease in usable process water, makes dry beneficiation of the fine coal fraction even more crucial. Dry fine coal beneficiation is a relatively young process with most of the methods still in the developmental phase. Additionally, many of the dry processing options available are better suited for coarser (+6 mm) and easy-to-beneficiate coal. Air winnowing for fine particles has been established in both agricultural and pharmaceutical industries, which indicates that the method can be used to separate smaller particles on a density basis and therefore, may prove effective in the coal industry as well. A proof of concept study was conducted using both computer-based simulations (which do not form part of this paper) and physical experiments. The initial winnowing unit consisted of a closed box with a horizontal air stream flowing through the top section. Coal particles were injected into the air stream and displaced horizontally across a distance (x), depending on the particle size and density, thus actuating a separation based on these two parameters. For this study particle sizes of 6, 4 and 2 mm were used all with a density ranging from 1200 kg·m-3 to 2000 kg·m-3. The simulation in Star CCM+ confirmed the findings of the mathematic behavioural model and provided a virtual representation of the separation using streamlines and particle tracks. The coal tests prove that size separation can be achieved at an airflow velocity of 21 m·s-1 and the density cut-point can also be predicted by using the prediction matrices constructed as part of this study. The results show efficiency values (EPM) of 0.11 and 0.09 at density cut-points of 1400 kg·m-3 and 1500 kg·m-3 respectively. The data obtained from the study indicates that air winnowing can be used to separate fine coal particles based on both size and density. However, in order to achieve an efficient density separation, a narrow size range is required. With some improvements to the model, simulation, method and design, the separation efficiency can also be improved. The next phase of testing will include the upscaling of the process to a demonstration plant, optimising the separation unit and testing the method on different qualities of coal. Keywords: Dry processing, fine coal, winnowing, simulation, tracers, demonstration plant

Jan 1, 2020

By Michael F. Roach, Joseph K. Cavey, Gary E. Taylor

A rigorous horizontal drilling and chemical grouting program was specified beneath the Hollywood Freeway (U.S. Route 101) section of Los Angeles Metrorail Contract C-311.Twin 6.67-m (22-ft.) diameter starter tunnels were to be conventionally mined through amixed alluvial and bedrock face consisting of silty sand, gravel, and weathered sandstone and siltstone of the Topanga Group. The contact between the alluvium and bedrock dipped toward the Crossover Excavation where the horizontal drilling and grouting operations were performed. The intent of this grouting program was to stabilize the mixed face to minimize ground loss and surface settlement, and to reduce groundwater inflow into the tunnel headings. Given the highly variable mixed face conditions, horizontal drilling up to 86 m (284 ft.) resulted in upward trending trajectories which likely followed the bedrock contact. Chemical grouting was performed in a primary, secondary and tertiary, three dimensional sequence. Evaluation of the primary and secondary grouting parameters indicated where tertiary grouting was required. Grouting pressures induced a small rock failure at the tunnel heading as well as increased stresses on the tiebacks of the excavation.

Jan 1, 1997

By Geoff C. Knight

Longwall mining using the shearer is acknowledged internationally as the most economically successful method of high volume production from underground coal mines. Since its introduction in the 1950s, a great deal has been achieved in developing the capability and reliability of the shearer - and the associated face conveyors and powered roof supports - to produce the competent systems now widely deployed. Equipment will continue to improve as knowledge and experience are gained and through the influence of market forces on the international equipment suppliers. However, current systems are so successful that further improvements are likely to be incremental rather than radical unless a high level of system automation is introduced. The automation concept is not new to the shearer-based longwall system. The opportunity and the need were recognized soon after the shearer and powered support were introduced in the 1950s. In the early 1960s, the British Coal Corp. (BCC; then the National Coal Board) attempted remotely operate longwall systems. Those imaginative early schemes were seen as failures at the time. But, with hindsight, a great deal was learned from the experience that stimulated automation research in several European countries. One of the most fundamental lessons learned was that coalface system automation is not possible until there is a high level of competence in automatically controlling the operation of the production machine itself within the coal seam. Once that is achieved, the rest of the system will follow with comparative ease.

Jan 1, 1991

By Dr. -Ing. Rainer Alles

Introduction Belt conveyors usually run in a straight line. The correct alignment is a major criterion for reliable functioning and optimum running properties. Any misalignment of the conveyor, especially mistracking of the belt, can have many negative effects. As a consequence of this, damage can occur on the belt and conveyor, some material can he thrown off at the edges and serious running problems can arise. In the worst case the belt can come off its supporting structure so that operations are brought to a halt. The absolutely straight alignment of a belt conveyor is actually impossible so that on closer observation every belt conveyor contains more or less sharp curves. Whereas on non-movable conveyors the deviations from the straight can he kept within the range of practical measuring accuracy by careful installation, movable conveyors in surface mining or belt systems in difficult terrain often contain curves that are easy to see with the naked eye. Below ground, too, alignment cannot always achieved to a desirable extent or is changed by geological faults over the years. Despite these unwanted curves, most belt conveyors perform their function reliably. In view of the belt tension, the belt tends to take the easiest path. This in general is the shortest distance between the pulleys on which the belt is tensioned and bent. This means for example that for a curve radius of 10,000 m over a flight of 100 m the greatest deviation from the ideal line is as much as 12 cm. And a figure of this magnitude cannot normally he accepted. In such cases, use is made of guide devices to properly train the belt if it doesn't center itself anyway. If it's possible to control the belt position over such unwanted curves. it can also he expected that the belt tends to follow the desired curved path within certain limits. I'd now like to cite a few examples to illustrate the ways and means of guiding a belt conveyor in curves. Cost-effectiveness The advantages of belt conveyors, in particular for longer conveying distances and mass flows have been known and undisputed for some time. However, there are often obstacles standing in the way of the concept of straight routing. If a belt conveyor is to bypass elevations or existing buildings or to follow the seam of underground deposits or a predetermined path, then substantially tighter radii and longer curves are desirable or necessary.

Jan 1, 1993

By E. B. Wright

THE property of Falconbridge Nickel Mines, Limited, is in Falconbridge township, approximately thirteen miles northwest of Sudbury. From the mine and townsite, a gravel road leads to Sudbury and a branch line of the Canadian National railway to Sudbury Junction. The ore deposit is at the southeastern corner of the 'Sudbury Basin'. It lies in a sheet-like mass, striking in an east-west direction, between norite to the north and greenstone to the south. The general attitude of the ore-body is vertical, but with frequent variations in dip of as much as 10° to the north or south. The deposit is very irregular in outline, the width varying from a few feet to eighty or ninety feet. In the vertical plane, rolls are frequently encountered. Gouge is very often present at one or both ore contacts. The norite to the north shows much jointing. The chief ore minerals are pyrrhotite, pentlandite, and chalcopyrite. The nickel content of the ore is usually double the copper content, average assays ranging from 2 to 2.5 per cent nickel and 1 to 1.5 per cent copper. The ore is of three main types: massive, breccia, and disseminated. The breccia ore, the most common type, consists of sulphides containing rounded inclusions of highly-altered country rock, which, in places, are so large that sorting is necessary in the stopes. In the norite, the breccia ore may grade into disseminated sulphides, which frequently are sufficiently concentrated for profitable mining. In places in the breccia ore, concentrations of solid sulphide masses occur. Until early in 1935, all mining at Falconbridge was by shrinkage scoping, but this method was found to be less and less suitable as greater depth was attained. When mining had reached the 1,000-foot level, ore drawn from large shrinkage stopes was found to have been diluted as much as fifty per cent by sloughing of the wall-rocks, caused by increased rock pressure and insufficient support. It was apparent that this method of stoping was un-suitable and -Mr. E. J. Martin was engaged to superintend the introduction of a method of cut-and-fill stoping.

Jan 1, 1938

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009

By Marco Zurco, Claudia M. Mendez, Alicia E. Ares, Carlos E. Schvezov, Carlos M. Rodriguez

"Zinc-Tin alloys were solidified in horizontal form and the obtained results were analyzed. During solidification the distribution of temperatures were measured by using thermocouples located strategically along the length of the samples. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solids fronts. Comparing the structure of the samples and the values of these parameters it was found that the temperature gradient reaches minimum values of as low as - 0.6 °C/cm, and velocities of the fronts of around 0.1 cm/s. In addition, the grain size was measured along the samples. The results are presented and discussed in the frame of the results previously obtained for other alloys.IntroductionGenerally solidification leads to two types of grain morphologies: columnar and equiaxed. The origin of each one has been the subject of numerous theoretical and experimental researches in the field of metallurgy for many years [1-7]. The columnar-to-equiaxed transition, CET, is considered as an object of high technological relevance with respect to the directional solidification of metallic alloys. This structure transition may be sharp or gradual and it has been reported to be dependent on thermal conditions associated with the casting process, including melt convection, heat transfer coefficients at the metal-mold interface, growth rates, thermal gradients, cooling rates, transport of solute, alloy composition, melt superheat, mold temperature, mold design, casting size, casting geometry, and the concentration of nucleating particles. As a consequence, it is critical for industrial applications to understand the physical mechanisms which control this transition during solidification. Many studies highlight the importance of the relative growth of the equiaxed and columnar grains and develop expressions or numerical procedures to describe a criterion for the CET. A number of experimental investigations reported in the literature suggest that the CET occurs when GL in the melt reaches a minimum critical value [5-7]."

Jan 1, 2012