Search Documents

By Robert T. Pring

IN addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of employees, with a consequent decrease in labor turnover rates. One progressive mining company1 estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination decreases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor. Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flowsheet. Exhaust ventilating systems are now afforded equal care in design and maintenance to that given other machinery more closely related to the process. METHODS OF DUST CONTROL "Dust control" is a general term descriptive of a number of methods used singly or together to prevent particulate atmospheric contamination. These methods are, in order of their desirability, as follows: I. Change of process. 2. Isolation of process. 3. Wet methods. 4. Ventilation. a. Local exhaust ventilation. b. General ventilation. 5. Personal respiratory protection. In ore-concentration plants it is seldom practical to change a process to eliminate the dust it creates It is possible in some cases to isolate a particular dust-producing operation from the rest of the plant, provided that constant attention on the part of the operators is not required. Frequently water is used in fine crushing and fine grinding, primarily to facilitate the processing of the ore and incidentally to allay the dust produced. Wet methods, however, are not feasible in coarse and secondary crushing operations, because of the relatively great volume of water required in instantly wetting each freshly fractured rock surface. Such quantities of water would entail conveying and storage difficulties. Local exhaust ventilation is the most effective and most commonly applied control measure, wherein directional air currents through the zone of dust production draw the contaminants into a duct system. Unfortunately, only a limited amount of reliable information on exhaust ventilation is available.2-5 Of necessity these publications are rather general, being primarily concerned with engineering fundamentals. While many organizations have successfully

Jan 1, 1940

Provide respiratory protection and a clean work environment for stationary or semimobile workers at minerals processing plants. Approach An Overhead Air Supply Island (OASIS) was developed which filters, conditions, and evenly disperses an envelope of clean air over a worker's head, thereby insuring reduced dust levels and a clean work environment. How It Works The concept for the OASIS derives from an earlier Bureau development of a canopy air curtain for continuous mining machines (see Technology News #21). In this application, the benefits of a reliable, self-contained, self-cleaning industrial-duty air filtration and distribution system are extended to the minerals processing field. The OASIS draws dust-laden room air into a filtration system, removing the dust and delivering clean air to a specific 16-square-foot area. It consists of: ? a self-cleaning primary filter ? a heater (cooling coil optional) ? an airflow distributor and secondary filter (combined)

Jan 1, 1985

By Thomas. Lisa, Mark Coleman

Schenck Process is an established customer-driven solutions provider, utilising its knowledge, expertise and technologies to transform production processes. Operating across several industries Schenck Process have developed quality solutions from their range of equipment to solve problems and fill holes in other people’s processes. In the non-ferrous metals industries Schenck Process have been using their Clyde Brand solutions in Pneumatic Transport to solve problems on smelter sites for a number of years, handling of concentrates, additives and metallurgical dusts. Working alongside clients around the world they have developed a number of dust handling systems for flash furnaces from New Boliden, through Codelco to PASAR. Solving handling issues in dust collection has proved to suit Schenck Process range of equipment well and now a series of solutions are available. Solutions have been developed to handle materials up to 600°C and can convey over 1 km. Conveying to remote location for disposal, injecting directly into a furnace through lances, return to furnace burner feed, or deliver and dose into leaching reactors, Schenck Process are ready to ‘make processes work’. Historic solutions at New Boliden and Codelco demonstrate a range of material application and the long term performance of the equipment. Recent installations at Pasar utilise the Schenck new ProPhaseTM equipment and handle the Waste Heat Boiler and ESP dusts directly and simplify the dust train. The paper will seek to show how this equipment can bring benefit in handling high temperature materials directly and eliminate several traditional steps that are often unreliable. The systems can be paired with Schenck Process new PHASiQTM and STREAMiQTM control systems which are complete PC, HMI, PLC, Interface system with full SCADA, Data Storage and IoT ready remote interrogation and support available. Installed in this challenging environment the systems are ready for smelter use. The systems can be also joined to our new E-nizingTM web portal. A perfect partnership to deliver the trend in ‘Big Data’ while providing visibility and off site support. The paper will show how these systems can deliver reliable equipment and remote support for these often isolated sites as well as delivering rapid return on investment. This paper discusses a step change in simplifying Flash Furnace Dust handling which Schenck believes shows the truth of Schenck Process Solutions claim that ‘we make processes work’.

Jan 1, 2019

By J Visser

Dust mitigation has long been seen as nothing more than managing a nuisance issue, but the reality is that poor dust management can lead to one or more of the following negative consequences: an increased risk of safety incidents, lost revenue, reduced and possibly even lost licence to operate, regulatory intervention, high staff turnover and/or absenteeism and occupational health and safety (OH&S) issues. Dust mitigation and management is not a black art; rather it is a scientifically driven process that can provide an opportunity to increase profits, increase the companyÆs status as an excellent corporate citizen, enhance staff retention and reduce the safety risk profile of the operation.The way to achieve success in dust mitigation and control is to apply the scientific method to each problem that can arise and plague any operation by using current industry best practice. This method of dust problem-solving can be applied to dust issues arising from specific dust sources and locations. The dust sources can include wind impacting on stockpiles, open areas, tailings storage facilities, moving train and truck loads, vehicular traffic on roads, the operation of shovels, front end loaders, draglines and other equipment, as well as ore movement on conveyors.The solutions will come from a combination of deployment of dust collection equipment, dust and moisture monitoring equipment, the appropriate application of water and chemicals, the introduction and maintenance of appropriate barriers and the use of predictive data from local and public weather stations. The paradigm shift required is to view dust mitigation as one aspect of normal operational practice, not a ænice to haveÆ or æunnecessary expenseÆ as most operators currently view it. This attitude is becoming more important as more and more local communities oppose the development of mines. One of the reasons for this local opposition is the inevitable dusty environment that is usually associated with mining.Dust mitigation is not a significant expense if correctly designed and included into the system, either as part of the original design of the operation or as a brownfield installation after the fact. Indeed, there is always a loss of revenue associated with dustiness resulting from ore movement and avoiding this goes a long way to paying for any associated dust mitigating costs.CITATION:Visser, J, 2013. Dust mitigation - changing the paradigm, in Proceedings Iron Ore 2013 , pp 27-38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D. H. d Hamly

THE work of Brown and others at Pittsburgh (Brown, Baum, Yant, and Schrenk, 1938)(1) and the success of their light field microprojector (Figure 1), have shown that the microscopy of dust quantitation can be greatly improved. It has been shown that dark-field microprojection of dust spots on konimeter slides is possible (Pullen, 1940), and this paper is a discussion of the new microprojector and a new counting method which is made practical by this instrument. The microscope makes possible the ready determination of the dustiness of mine ventilation air. Reduction of the dust concentration from a dangerous to a safe level involves one or more of the following: reduction of dust production, filtration of the air stream, or dilution with non-dusty air. Each of these raises important engineering problems of time and costs, and trustworthy information on the state of dustiness of the air is required ?both before and after the employment of any method of reduction. Records of this information may be divided into two broad classes concerned with safety: (1) the level of dustiness, and (2) the quantity and kind of dust produced by a machine under a given set of conditions. Though the first requires only one determination for a given time and place, numerous routine records are required to show the continuous safety of the air in an actively producing mine. Though repeated samples are required, highly accurate counts are not needed to show safety or to indicate whether a substantial increase in the non-dusty ventilation air has produced a proportionate decrease in the dustiness of the mixed air. The Devers and Gathercole konimeters have proved satisfactory instruments for this purpose in Ontario.

Jan 1, 1942

By R. A. Jankowski

The U.S. Bureau of Mines has conducted a study to identify the sources of respirable dust and appropriate dust controls applicable to today's high tonnage longwall faces. The primary source of respirable dust identified is the cutting action of the shearer; however, the pct contribution of dust from coal transport through the stageloader/crusher was significant. This was primarily due to the high rate of mining, requiring rapid and constant coal transport. Techniques implemented for the control of shearer-generated dust included high drum water flow rates, deep cutting, shearer-clearer-type external water spray systems, and radio-remote control. The high water flow rates, and an enclosed stageloader with scrubber, were used to control dust during coal transport. No novel or effective control technology exists to control dust during support advance. Administrative controls for dust avoidance, and manual and batch-activated electro-hydraulic control systems were used to keep support movers out of the dust generated during support advance.

Jan 1, 1990

By D. Marino

Over the last 20 years, the manufacturing sector of our country has been called upon to comply with ever core stringent environmental standards. The primary metals sector was particularly hard hit early on, to develop the technology, acquire the equipment, and implement the programs to eliminate or reduce the by-products of metal making. To this end, through a combination of technological innovation and extensive capital expenditures, the metals industry has met, and in many cases, exceeded the minimum standards. It is to this escalating cost - liability exposure issue - that Dereco has addressed itself. As we move into the decade of the 90's, the challenge facing the metals industry concerning the environment will be even more difficult than the previous decade. To focus in on one major aspect of legislated environmental regulations, the issue we will address today is; now that the by-products of metal production have been identified, accounted for and collected, how are they to be disposed of? During the course of this presentation, actual data will be presented from our 4 1/4 year on-site experience at J & L Specialty Products

Jan 1, 1992

By Geo. T. Lynch

PALEOLITHIC MAN, laboriously shaping a stone implement in his cave, discovered that the dust irritated his eyes and nostrils and hindered his labors, whereupon, muttering a few incantations, forerunners of modern profanity, he removed himself and his work outside. There, ignoring the jeers of the hairy ?old-timers,? he turned his back to the wind and resumed operations in comparative comfort. Thus originated the dust problem in the mineral industries, and its solution. Despite long familiarity with the annoyance, danger, and loss occasioned by dust, little progress was made in the engineering solution of its problems until recent years. Some advance can now be reported but too many traces of ancient tradition and practice still remain. Considerable published information is available but only a part of this is of proved accuracy and utility. The greater portion is either misleading, being derived from too few cases to be of general application, or entirely erroneous, originating in guesswork, legend, or individual inspiration, divine or otherwise. The engineer, confronted with a dust problem, has neither the time nor the special training required to extract the values from this mass of low-grade. It is, therefore, desirable that we attempt to correlate the known values and to put them into a form upon which actual progress can be based. This discussion is, then, for the benefit of that engineer, particularly the engineer in the mineral industries and more particularly in ore-dressing plants, and is merely a gathering of facts already known but difficult to segregate.

Jan 1, 1938

By Cody Giroux, Homer Scurlock, Michel Wasag

Silica and Crystalline Quartz exposure continues to be a serious health threat to nearly 2 million workers in the United States, including more than 100,000 working in high risk jobs such as abrasive blasting, foundry work, stonecutting, rock drilling, quarry work, mining and tunneling. The primary focus of this study is to identify the best methodology to reduce particulate-laden air and limit/eliminate exposure to respirable dust with silica/crystalline quartz during tunneling operations. This study focuses on two de-dusting systems employed on similar tunnel construction projects. The first project is the Coxwell Bypass Tunnel located in Toronto, Ontario Canada. The second project is the Westerly Storage Tunnel located in Cleveland, Ohio. The Toronto project is utilizing a wet de-dusting system. The Cleveland project is using a dry de-dusting system. The objective is to determine which system provides the best protection and suitability to capture, remove and ultimately reduce respirable concentrations of silica/ crystalline quartz to safety and healthy levels in underground tunneling activities.

Jun 13, 2021

By Liang Wang, Sheng-Kai An, Bing Xie, Hong-Yi Li, Cui Li

In order to develop an environment-friendly method for extracting vanadium effectively from aqueous solution containing vanadium, the dynamic adsorption behavior of V by a continuous fixed-bed column which was filled with macro-porous weak base anion exchange resin was studied. Effects of conditions including the bed depth, flow rate, concentration of vanadium ions on dynamic V adsorption were investigated. The optimum adsorption conditions were established at flow rate of 6 ml/min with bed depth of 20 cm. Isotherms studies demonstrated that the column adsorption of V was a favorable chemical ion exchange process in monolayer. Several kinetic models were applied to analyze the adsorption characteristics. Analysis results of the Bohart-Adams model indicated that the adsorption process was dominated by external mass transfer in the initial stage. The Thomas model was appropriate to describe the column behavior, revealing that both external and internal diffusions were involved in the limiting steps.

Jan 1, 2014

By Fengming Li, Baocheng Song, Yuemin Zhao, Hailin Dong, Liping Peng, Chusheng Liu, Chenlong Duan

The large-scale vibrating screens with high processing capacity and efficiency are now in great demand in the mineral processing industry of China. However, as the equipment is always suffering from the strong external harmonic exciting force, the inertial force and the impact from the minerals, the fracture of the beam and the crack of the lateral plate are easy to occur, which has a negative effect on the reliability of the equipment itself and the industrial production. Considering the essential high reliability of the equipment, a new large-scale vibrating screen with duplex statically indeterminate mesh beam structure (VSDSIMBS) was developed. The natural characteristics, namely, the natural frequency (or the modal frequencies) and the natural mode, and the dynamic characteristics of the VSDSIMBS were obtained by the modal analysis and the harmonic response analysis. In addition, the dimensions and the constructions of the statically indeterminate plate and the mesh beam were chosen as the design parameters, to which the sensitivity of the whole mass, the maximum deformation and the maximum stress of the duplex statically indeterminate mesh beam structure (DSIMBS) were summarized for the optimization of the DSIMBS. Now the large-scale VSDSIMBS is being well used in China.

Jan 1, 2014

By Ramon Augusto Moretti, Henrique da Rocha Severino, Renato Nascimento de Castro, Fernando Cesar Sousa

Rolling stand 12 (LTx) of long steel, installed in the company A, Piracicaba - SP unit, had presented high levels of vibration, which affected its internal components, such as: shaft, gears and bearings, generating downtime. To evaluate this equipment a study was proposed by the following engineering techniques: Conventional Vibration Analysis, Operational Deflection Shape (ODS) and numerical simulation by the Finite Element Method (FEM). In the Conventional Vibration Analysis, high levels of vibration were observed during manufacturing process, especially when the material reaches the equipment. Impacts generate high values in acceleration, on average 80 m/s² peak to peak. In the moment of impact, misalignment of internal components was observed by ODS. Field results were correlated to those obtained by the Finite Element Method, which allowed to calibrate FEM model. Thus, the most effective structural modification already numerically evaluated was implemented in the system. Afterwards, new measurements by vibration and ODS techniques were performed, and attenuation of vibrational levels and operational mode, which overloaded the internal components rolling stand, were verified.

Oct 1, 2019

By Frank Rausche

Without doubt, driven piles are the most economical deep foundation element for a nearshore environment, providing for high bearing capacities and stiffness, quick installation times, assured quality by simple monitoring and inexpensive dynamic load testing during restrike testing. However, when the pile top elevation is several meters below water surface, questions often arise as to the most reliable and economical pile installation method. Frequently encountered, yet relatively expensive, solutions include driving inside a dewatered cofferdam, driving long piles that are later cut off below water surface, or using an underwater hammer. Arguably, the most economical solution is driving the piles with a follower or chaser. However, many foundation engineers shy away from this solution because of the uncertainty associated with the transfer of energy through the interface between follower and pile, the associated potential driveability problems and maybe the limited fatigue life of the follower. This paper will demonstrate how the driveability of a hammer-follower-pile-soil system should be analyzed prior to installation and how to model the pile-follower interface both for steel and concrete piles. As an example, results will be presented which were obtained for both steel pipe piles and precast concrete piles, driven by a single-acting diesel hammer through a steel follower for a pre-construction test pile program in Venice, Italy. While analysis of the steel pile-follower system was straightforward, for the concrete piles, the presence of a soft cushion material whose material properties changed continuously posed some difficulty. Pile Driving Analyzer® measurements and CAPWAP® analysis yielded not only realistic stresses and transferred energy values in the pile, but also reasonable model parameters for further use in a pure wave equation analysis. As a side note for clarity, the dynamic measurements and analysis results herein presented are based on the GRLWEAP and CAPWAP software. GRLWEAP is commonly used all around the world for the preparation of pile driving jobs. The program either yields a bearing graph that relates bearing capacity and pile stresses to blow count or set per blow or it predicts blow counts and pile stresses as a function of pile penetration. These results allow the contractor to estimate driving time and select an economical hammer and driving system for a safe and efficient installation. CAPWAP on the other hand is the analysis of choice once a pile has been installed and records of pile top force and velocity have been acquired during installation or during a restrike test. CAPWAP is a signal matching program which calculates for one particular impact (for example at the end of driving) the static and dynamic soil parameters. Its final results include the calculated resistance distribution, the complete stress history in the pile and also a simulated load set curve. The CAPWAP calculated dynamic soil parameters can also be used in a Refined GRLWEAP analysis to generate a calibrated bearing graph."

Jan 1, 2006

By B Darlington, L Sandberg, O Vallati

The D47 and D39 Mechanical Dynamic Extra bolts (D47 MDX and D39 MDX) have been developed in response to the ever-increasing demand from the mining industry for rock bolts with high dynamic capacity. To prove such capacity, Sandvik has performed numerous in situ dynamic testing with the unique Dynamic Test Rig (DTR) (Darlington, Rataj and Roach, 2019; Roach, Rataj and Darlington, 2019). To complement the collection of testing data, Sandvik, in collaboration with the Swedish Research Institute for Mining, Metallurgy and Materials (Swerim) have performed additional experiments in laboratory condition using Swerim’s new drop test rig. This rig utilises a momentum transfer method to apply a dynamic load to the bolt. The sample falls together with the mass until the support beam impacts stationary dampers and the momentum energy is transferred to the bolt. Part of the charged energy is released by the dumpers while the remaining portion is absorbed by plastic deformation and/or displacement of the ground support element. The D47 and D39 MDX bolts have been tested at Swerim’s test facility with different levels of input energy. Six tests were performed at the specification energy of 36 kJ and six tests were carried out with the maximum allowable energy from the facility, ie 44 kJ. The bolts confirmed their dynamic performance absorbing the input energy without failure. The D47 MDX bolt absorbed up to 33 kJ with 150 mm displacement while the D39 MDX bolt absorbed up to 35 kJ with 162 mm displacement. This work will present an overview of the drop test rig at Swerim’s facility and a collection of results of the test performed on the D47 and D39 MDX bolts. The test method and results will be analysed and compared to the tests carried out with the in situ DTR.

Nov 29, 2022

A PDP 11/34 computer has been inter- faced to existing instrumentation in a 400 tph rod-mill/ball-mill grinding circuit and programed with a Kalman filter to estimate several unmeasured variables. A dynamic two-size- fraction model of the circuit is used to predict the complete state of the circuit including particle size distributions around the circuit, mass holdups and flowrates, the ball-mill grinding rate, water additions and cyclone parameters. Online measurements of sump level, slurry densities and product particle size are used to update the model values sequentially on a 20-second interval. This procedure results in optimal estimates of circuit variables given the relative reliability of measurements and the accuracy of the model.

Jan 1, 1983

By Arthur Miller, Andrew Weakley, Heather E. Lawson

"IntroductionDynamic failure events in an underground coal mine, or “bumps,” are defined as “the sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillars, or the solid block of coal being thrown into an open entry” (Peng, 2008). Reports of disastrous and often fatal dynamic failure events date back over one hundred years in the United States. Mining practices and technologies have significantly evolved over the course of the last century, yet these events continue to occur. The events at Crandall Canyon, Utah (Gates et al., 2007) and Brody No. 1 Mine in West Virginia (Barker and McNeely, 2014) are two recent failure events that resulted in a total of eleven fatalities. These events testify to the fact that dynamic failure remains an imperative safety concern. Furthermore, their continued occurrences indicate that engineering controls have proven inadequate at wholly mitigating the problem.Multiple conditions have been associated with the occurrence of dynamic failure phenomena, including• thick, competent strata that can create a bridging effect, resulting in high abutment stresses (Rice, 1935; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Agapito and Goodrich, 2000; Peng, 2008; Whyatt, 2008; Whyatt and Varley, 2010)• overburden thicknesses greater than 500–700 ft. (Rice, 1935; Peng, 2008)• a strong coal that is resistant to crushing (Rice, 1935; Peng,2008) or that is “uncleated or poorly cleated, strong…sustains high stress and tends to fail suddenly” (Agapito and Goodrich, 2000)• the presence of sandstone channels or rolls that can serve to concentrate stresses (Iannachione and Zelanko, 1995; Agapito and Goodrich, 2000)• fracturing of strong units above or below the coal seam (Whyatt and Varley, 2010)• slip along pre-existing discontinuities (Peperakis, 1958; Whyatt and Varley, 2010)• multiple seam mining interactions (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995; Newman, 2002; Peng, 2008)• mining sequences that can cause anomalously high stress concentrations (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995)"

Jan 1, 2015

By D. Morgan Warren, David Hanson, Alice Alex, Tom Meuzelaar, Heather Lawson, Sam J. S. Wright

Dynamic coal failure events remain a safety concern in underground coal mining due to their sudden nature and high fatality rate. Previous research utilized Principal Component Analysis on field samples revealing strong empirical correlations between positive failure history and low sulfur content (S) and high volatile matter (VM). Further studies indicated that bumping coals tend to be less mature and less well-cleated than non-failure coals. However, these in situ studies faced the challenge of distinguishing intrinsic coal properties from external geological and stress-related influences. This study augments previous findings through laboratory experimental testing of coal samples that included unconfined compressive strength, chemical composition analysis, and qualitative observations on cleating, combined with compositional data analysis and machine learning techniques, to isolate and understand coal’s inherent bursting capacity. These results further confirmed the relationship between coal chemistry and failure classification.

Feb 22, 2026

By Manfred Hager

The ability of conveyor belts to transport large mass throughputs economically over previously unprepared ground has resulted in this system achieving great and extensive use. A significant component in this development is the conveyor belt itself. The development of high strength steel cord conveyor belts involves the optimising of splice design, the use of excellent rubber material especially in the splice, good craftsmanship during splice production and modern field vulcanisation equipment. The durability of a splice for belts of class St 3000 up to St 790 is expressed by the fatigue strength under dynamic stress. The results obtained with a test method and equipment developed by the University of Hannover indicate the present state of the art in this field. Belts of high nominal strength used on inclined long distance conveyors reach splice fatigue strengths of about 3000 N/mm. The design should only exploit approximately 50% of the fatigue strength determined in the tests as maximum operating stress. IMPORTANCE OF CONVEYOR BELT SYSTEMS The use of conveyor belt technology has expanded considerably over the last decades in the bulk goods transportation sector. Because of the favourable transport costs and the technology's adaptability to specific topographies, belt conveyors frequently represent the most economic solution. When flows of goods are large, as in German lignite mining operations, where masses of up to 40,000 t/h are given, it is the only technically feasible alternative. The use of belt conveyor systems allows the sensible distribution of the waste and the production of the coal (Hager, 1981). But this transportation alternative is also suitable when the masses involved are smaller. Whereas conveyor belts were only suitable for loose bulk goods up until a few years ago, today they are frequently also used for hard rock open cast mines, e.g. in the production of copper ore. Because of the favourable transport costs it is frequently still economic to use mobile crushers with a throughput of up to 10,000 t h 6 which breakdown the large blocks produced y explosives into transportable grain sizes. In many operations, trucks are only used to provide flexibility between the excavator and the crusher, i.e. over short routes, and the long, frequently steep, transport paths to the processing plant or to the spreader are undertaken by belt conveyors (Einenkel et al., 1992). The advantages of belt conveyors, i.e. to cope with large mass flows over inclines and down slopes of up to 1:4 have resulted in this system gaining very extensive use throughout the world. The conveyors can be installed over for the most part unprepared ground with suitable vertical radii, adapted to the locally available belt material. In the process individual conveyor belts with lengths of up to 15 km, and in the underground sector with lift heights of up to 1 km, have been built and operated. This great variety of application possibilities is complemented by a limited ability to pass through horizontal curves. This can be achieved with the help of design measures on the conveyor whilst bearing in mind the characteristics of the belt. STRESSING OF CONVEYOR BELTS IN DIFFERENT TYPES OF PLANT The advantage of conveyor belts compared with other systems is also to be found in the large available service-time window, i.e. the excellent reliability and the low costs of energy consumption and maintenance. It is in particular the reliability of a belt transport system which depends to a great degree on its main component, that is the belt - in all its different types and variations. For this reason, the belt is also given the greatest attention in the development of the individual components, because it is the belt which must be designed optimally with regard to various factors. The specific properties of the conveyor belt then assert a considerable influence on the design and sizing of most other components in a

Jan 1, 1993

By A Whaanga, W Vigor-Brown

IGO Ltd’s (IGO’s) Nova-Bollinger Deposit (Nova-Bollinger) is a magmatic nickel-copper-cobalt (NiCu-Co) sulfide deposit found 160 km east-north-east of the town of Norseman in Western Australia (WA). The deposit is hosted by the Mesoproterozoic rocks of the Fraser Zone, which is part of the Albany Fraser Orogen (AFO). Since mining commenced in 2016, IGO’s Nova Operation (Nova) has mined and processed to 31 December 2020, 5.63 Mt of ore grading 2.04 per cent Ni, 0.86 per cent Cu and 0.07 per cent Co. Nova’s mine geology team (MGT) has used commercially available implicit modelling (IM) and general-purpose resource modelling (RM) industry software systems, to prepare the 31 December 2020 (CY20) update of Nova-Bollinger’s JORC Code reportable Mineral Resource estimate (MRE). This CY20 MRE update was predominantly based on ~386 km of diamond core drilling, with the drill holes having a nominal grid spacing of 12.5 by 12.5 m throughout the mineralised zones of the deposit. Using IM tools, Nova’s MGT interpreted and modelled 22 separate domains from the drill hole logging, assaying results, and the MGT’s underground mapping. These IM closed volumes were then used to control the estimation of MRE variables into conventional industry digital block models using RM and other ancillary software systems. During 2021, a commercial machine learning (ML) software was trialled by Nova’s MGT for preparing block models of Nova-Bollinger’s MRE domains. The motivation for the trial was that the ML process could expedite modelling through the direct creation of a domain coded block model from the drill hole logging. Compared to the industry standard approaches of wireframing or IM, where the modeller usually makes many subjective choices to produce the domain model, ML offers a more objective ‘hands-off’ process for determining the connectivity of domains defined in drill holes. Additionally, the ML process provides a quantitative confidence metric associated with its output that may have utility in mine production and resource classification. In this paper, the results of the Nova-Bollinger ML modelling trial are compared to the MGT’s current workflow for MRE work. The MGT’s conclusions as to the advantages and disadvantages of the IM and ML methods for preparation of MRE domains are discussed. The ML software was also tested as a method of rapidly interpreting geology outside the principal zones of MRE interest. These testing results are also presented in this paper.

Mar 22, 2022

By Behrouz Abedian, Livia M. Racz

"We address dynamic interactions between high-energy, reactive surfaces of polymer-matrix composites and solid surfaces. A common characteristic of these interfaces is that bonding occurs readily upon contact. In many industrial and biomedical applications, it is desirable to suppress this bonding phenomenon. This interfacial effect is discussed in light of the development of our new method of handling polymer-matrix composites in dental applications. This method involves vibration of the solid-polymer interface at different frequencies. For each material, there is a critical frequency at which the sum of the viscoelastic and inertial energies of the fluid at the surface exceeds the energy available for bonding. When the polymer is vibrated at or beyond this frequency, it does not adhere to solid surfaces. An important aspect of the developed process is that it can be used to characterize surface and interfacial properties of polymers under dynamic conditions, whereas existing techniques are restricted to the study of bulk dynamic properties.IntroductionThe purpose of this paper is to report on the development of a new method for manipulating polymer-matrix composite materials used in dental applications, and the potential of this process for use in materials characterization. The materials under discussion have polymer matrices of a combination of bisphenol A-glycidyl methacrylate (BIS-GMA) and triethylene glycol dimethacrylate (TEGDMA), and contain filler particles of silica and/or zirconia glasses. These materials are called direct aesthetic restorative materials, and are used for filling of cavities, repairing chipped teeth, and for other restorations in which appearance is of importance. They have the appearance of natural tooth material, and are therefore in great demand for use in the anterior portion of the mouth(l,2)."

Jan 1, 1998