Search Documents

By George K. Clement

Manual estimating method through use of equations, factors and curves for preparation of feasibility type estimates for capital and operating cost of mining and primary beneficiation in the United States and Canada of various types of minerals occurrences, except fossil fuels, using state-of-the-art technology. User should have basic estimating experience in the mining industry and/or related fields. Primary usage of this handbook will be for the preparation of preliminary estimate within a reasonable degree of accuracy with relative small amounts of hard input data. Output may be used to determine if a more finite type of estimate should be produced.

Jan 1, 1978

By D. A. Paice

A power supply to operate fluorescent or mercury vapor lamps from 300 volt dc coal mine trolley wires has been developed for the Bureau of Mines. A high frequency regulated inverter unit incorporates ballasts for a mix of lamp loads up to 650 watts. For 600 volt trolley systems an additional power converter unit was developed to step down the dc voltage to 300 volts for the inverter unit. Both units have operated in a working coal mine for over 12 months without need for servicing. The lamp load in these tests included two 100 watt mercury vapor head lamps and six 75 watt fluorescent lamps.

Jan 1, 1979

By Tim F. Dyson

Feasibility of employing automated processing and detection techniques in the mine disaster communications problem is demonstrated. Efficient processing methods are developed. These methods have been demonstrated both in a laboratory and in a field environment. Evalua¬tion of existing computer capacity is given along with recommendations for expansion.

Jan 1, 1981

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitled ?Evaluation of Proximity Warning Devices? dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electrostatic fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factor of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Peter Murphy

This report (arid related appendices) provides a description of the functional design specifications, engineering design specifications, and program of instruction for development of a training system for dragline equipment operators. Based upon a task analysis and training system analysis prepared under Phase I, Phase II efforts expanded upon and refined the functional design specifications. The training hardware components have been developed to a point shy of system fabrication. A detailed outline of the porgram of instruction and content sequence has been prepared. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1976

By Kent W. Hawley

An improved visibility system was developed for use on the large (100 ton+) haulage trucks typically operated in open pit and surface mines. The improved visibility system provides the truck driver' with a means of viewing hazardous situations that occur in the extensive blind areas adjacent to his true. The cost effective, reliable, visibility system consists of a closed-circuit television three unique fresnel viewers, and two improved mirrors. This report describes the visibility problems of Large trucks in the surface mining environment, shows the performance of existing mirrors, substantiates concept selection, and describes the prototype improved visibility system.

Jan 1, 1978

By John L. Dahle

This report documents the research efforts that were undertaken to design, install and test noise abatement devices for use on off-highway haul trucks operating in surface mines. The objective of the program was to reduce the environmental noise from haul trucks. The noise reduction devices that were developed utilized existing technology and were tested on a 50-ton haul truck. The efforts emphasized the reduction of noise emitted from the engine compartment which included the use of side shields, sound absorbing material, improved radiator shroud design, and a modulating clutch fan. Noise tests were conducted using modified SAE test procedures for measuring sound levels around a stationary and moving machine, and inside of the operators compartment. Test results showed a maximum of 4 dB(A) reduction measured 16 feet from the truck. Interior cab noise was reduced 6 dB(A) with the windows and vents closed.

Jan 1, 1983

By Wils L. Cooley

Several aspects of mine safety grounding systems and equipment are studied. Electrolytic corrosion of test ground beds has shown a high incidence of stray current damage, while efforts to build a reliable continuous ground bed monitor continue. Laboratory and field investigations of trailing cable splices have yielded strong evidence that splices can contribute to stray current problems in the mines, but a method is suggested for discovering deteriorating splices before they pose a serious hazard. A prototype device has been constructed to evaluate the electrical resistance of rail bonds underground as a source of stray current. Theoretical modeling of ground electrodes, has advanced considerably, now covering measurements of large cylindrical electrodes, multiple-rod ground beds, rod electrodes in stratified earth, and measurement of connected beds. A prototype instrument design is given for a potential gradient plotter to quickly evaluate voltage gradients near earth electrodes. Additional ground-check monitor testing is reported.

Jan 1, 1977

By GJ Hundman

The Multiple Unit Continuous Haulage (MUCH) System was designed to provide the capacity to continuously convey coal from the mining machine to the main haulage belt. The MUCH System has an operator who steers the lead vehicle, ever following the mining machine. All the remaining vehicles follow the path of the lead vehicle, with their conveyors automatically lining up between the lead vehicle and mine section panel belt. This is accomplished by mechanical linkages on the vehicles which are interconnected by steering bars between vehicles (patent pending). The MUCH System has an operator who steers the discharge vehicle when outby travel is required. Outby travel is just like inby, with each vehicle following the path of the preceding vehicle. Surface tests overwhelmingly indicate the "UCH System should track/retrack successfully in square pillar underground room and pillar coal mines with 18 ft. wide entries and slopes up to 10 percent. For 60 degree pillar plans the minimum entry width required is 15 ft. Surface tests also indicate the MUCH System will convey over 8 TPM of coal around 90 degree corners without excessive spillage.

Jan 1, 1983

By Paul J. Guay

This report presents the results of evaluating a longwall mining system specifically designed to extract a very deep web (60 inches or deeper) from a longwall panel. The report includes a productivity and cost analysis comparing the new mining sys-tem with a high capacity conventional longwall operation taking a 30-inch wide web. The analysis shows the new system will increase annual production 44 percent and decrease cost per ton off the face 21 percent. The report also includes conceptual drawings and specifications for a high capacity four-drum shearer and a unique shield type of roof support specifically designed for very wide web operation. The advantages and problems associated with wide web mining are discussed in general and as they relate specifically to the equipment selected for the new mining system. The study concludes by recommending that surface coal loading tests be conducted as the follow-on work.

Jan 1, 1978

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By F. J. Prokoski

The COALSTAR Project, which operated from November 1981 to December 1982, was a research and development project aimed at providing a reliable and inexpensive means of monitoring various waste site conditions via the GOES satellite system. The GOES system provides data transfer from unattended isolated sites where neither power nor telephone lines exist. The reliability and resolution of the data received while using the satellite link were excellent; however, the site instrumentation gave considerable trouble. The disastrous failure of a large coal waste embankment in 1972 led the Bureau of Mines to undertake a comprehensive program to reduce the likelihood of such an occurence again. Part of this program involved the installation of instruments to monitor the stability of a specially-selected embankment operated by Armco Incorporated near Montcoal, West Virginia. Initially, the instruments were monitored by normal telephone lines and used normal commercial power from the local utility. The project described here was initiated to replace this monitoring system with an unmanned, solar-powered data collection system which transmitted data via satellite to a central computer facility. The satellite data network is the National Earth Satellite Service of the National Oceanic and Atmospheric Administration.

Jan 1, 1984

By D. A. Paice

Direct current electrical systems are used in most coal mines primarily to power the main haulage trains and secondarily to feed other equipment and passageway lighting. Electrical power is supplied from rotary machines or static rectifier equipment and is distributed through the mine by open trolley wires and feeder cables. The rails of the haulageway are used as a current return path. This exposed power distribution system is very vulnerable to conditions which lead to undesired leakage currents and short circuits and, consequently, the possibility of fires or other hazards to personnel. Present techniques and equipment have been utilized in so far as practical to improve the safety of the dc electrical system; however, there still appears a need for further improvement. Because of this need, this program was sponsored by the Bureau of Mines to investigate two specific technical areas related to improvement of dc electrical system safety. One area included the determination of the characteristics of mine electrical systems and their protection requirements and the verification of the adequacy of available protective devices for mine service. Despite the widespread application of industrial protective equipment in mines, there was little detailed technical information available related specifically to the performance of this equipment in service. Our task was not only to develop useful information regarding mine system protection, but also to define and verify the adequacy of the protective devices available. The second area of investigation called for development of a practical technique for detecting low level electrical fault or leakage currents. Conventional protective devices

Jan 1, 2012

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine would be drilled. The geologic formations encountered in this hole are discussed. Correlation of the geologic horizons encountered in this hole with those encountered in nearby drill holes was accomplished by the use of geophysical logs. Data on the geophysical interpretations are provided. The anticipated geotechnical characteristics of the geologic units encountered in Pilot Hole "X" are described.

Jan 1, 1977

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Michael L. Clar

This volume is an annotated bibliography of published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines. This literature was used to develop Volume 1 of this report, which assesses the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. Each abstract is followed by subject descriptors. the abstracts are listed alphabetically by title and are numbered consecutively. These numbers are used in the subject index to help the reader locate the appropriate articles.

Jan 1, 1981

By R. S. Nutter

The results of designing, constructing, and laboratory testing of a modular, distributed, microprocessor-based mine monitoring and control system are presented. A standard computer communications protocol (DDCMP) was utilized throughout the system. Tests were performed on the utilization of a high-level language for programming mine monitoring and control systems. Laboratory tests were run on a combined air velocity/methane sensor.

Jan 1, 1980

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By Robert R. Perron

The U. S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 15 to 30 ampere fault to ground, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1975