Search Documents

By Frederick C. Kohout

An advanced water-in-oil emulsion hydraulic fluid has been developed which meets defined laboratory performance criteria and which has given fully satisfactory results in a one-year underground mine test in two continuous miners. A novel method of monitoring fluid water content was demonstrated and incorporated into a test kit for use at or near the mine site. Test fluid fire resistance integrity as measured by the MSHA Schedule 30 procedure was maintained during the test and important fire resistance test variables identified.

Jan 1, 1979

By Mackenzie Burnett

An inducer-type pump, capable of injecting dry coal into a hydraulic transport pipeline has been developed and installed in a specially designed and fabricated slurry injector vehicle. The full scale prototype injector system can deliver up to 11 ton/min of coal into an 8-in pipeline t pressures up to 95 lb/in2. The Helical Inducer Injector operates on centrifugal principles with flow passing axially through helical pitched conical rotor. Water is delivered to the pump through an annular slot at the atmospheric pressure coal inlet. The spinning rotor maintains an air-core vortex of water which pressurizes the discharge housing. A screw feeds coal through the open inlet into this vortex. The inner radius of the vortex contracts as pressure is increased, giving a limiting maximum pressure which is proportional to the square of the rotor speed. Below this limit, flow rate, discharge pressure, und rotor speed re independent variables. The self-powered, 4 -in high slurry injector vehicle follows and receives ROM coal from a continuous miner, reduces the top size to 3-in, and delivers the sized coal to the injector feed screw for slurry formation and pumps it through a mobile hose attached to the vehicle's outby end.

Jan 1, 1983

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By Richard Lusignea

A single boom roof bolting machine was outfitted with measurement and recording systems for detecting changes in machine parameters while drilling. The purpose of this instrumented bolter or "smart drill" is to detect changes in roof conditions from the machine parameters of penetration rate, thrust, rotation rate, torque, rejected light from rock cuttings, and vibration of the roof during drilling. The system was demonstrated underground in coal mine conditions and showed correlation between rock type and drilling parameters.

Jan 1, 1982

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mine operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also Investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result in reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By J. Cseff

A variety of shaft and hoist equipment exists in the United States. Nearly all hoist systems are electrically driven. Machine elements which comprise the hoists and ancilliary equipment include bearings, shafting, drums, gear reducers, couplings, brakes, clutches, sheaves and electrical motors. Volume I, Systems Description, describes the various components encountered in most mine hoist and shaft installations, and brief descriptions of functions and constructions. Hoist ropes and balance ropes are specifically excluded from this report. Associated with the hoisting system is the headgear, shaft and equipment, loading/dumping facilities and the actual conveyances and their rope attachments. Volume II, Inspection and Maintenance Procedures, discusses scheduled Inspection and preventative maintenance in general terms. Preventive scheduled inspection and maintenance procedures assist in the smooth operation of mine hoisting plant, by the prevention of unscheduled or catastrophic equipment failure and its attendant downtime. Schedules and overall maintenance planning is required at the management level. Records and equipment logs must record inspection and maintenance, and unusual operations or incidents. A cross reference between MSHA regulations and various equipment components is included as part of the report. A discussion of the various non-destructive testing methods which may be applied to hoisting equipment is also included.

Jan 1, 1981

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and laboratory testing of dust collectors for use on double drum shearers. Systems tested included: ? High Capacity Flooded Bed Scrubber ? Water Powered Extraction Cowls ? Water Powered Extraction Drums ? Water Powered spot Scrubbers. The systems were tested using tracer gas in a full-scale model of a longwall shearer face. This report provides a detailed description of the test facility, test methods, and system test results.

Jan 1, 1982

By K. T. Menzies

This report documents laboratory and in-mine analyses of diesel exhaust pollutants carried out to assess the fate of potentially reactive species in the mine environment. Specifically, the concentration of stable compounds including carbon monoxide and carbon dioxide, and potentially reactive compounds including nitric oxide, nitrogen dioxide, sulfur dioxide, aldehydes, formaldehyde, acrolein, formic acid, odorants, particulates, soluble sulfates, and polynuclear aromatic hydrocarbons were determined. The concentration and mass emission rates of these compounds were measured in the laboratory under three engine speed and load conditions and with three exhaust control conditions, i.e., none, catalyst, water conditioner. Once calibrated, the engine was installed in the Bureau of Mines Safety Research Coal Mine and the concentration of exhaust pollutants measured at several distances downstream (inby) of the engine. Laboratory results confirm the relatively small effect of exhaust control devices on most pollutants under engine conditions of low speed and load. At higher engine speed and load, the catalyst is more effective in controlling many pollutants. The in-mine data indicates that during residence times, which are typical for miner/exhaust contact, most diesel exhaust pollutants do not decrease in concentration. The obvious exceptions are nitrogen dioxide, sulfur dioxide and formaldehyde. The concentration of these pollutants is reduced by up to 75 percent in five minutes. The lack of increase in levels of obvious reaction products indicates that surface loss may be a major sink for these pollutants.

Jan 1, 1980

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By J. W. Adams

This report surveys the efforts of six contractors to the U.S. Bureau of Mines with regard to their electromagnetic noise measurement programs. What has been done, what is planned, and evaluations and recommendations are given for each contractor. The main observation is that to date there is not sufficient knowledge of electromagnetic interference in mine environments to design a reliable communication system. This knowledge should be available by the end of June 1972 if certain planned programs are completed successfully. A major effort of this report is to establish parameters to be measured, units to be used, and workable formats for data presentation. This is given in Appendix A. Some details concerning equipment, procedures, locations, and sample data are included in Appendix B.

Jan 1, 1971

By Charles J. Haas

The objective of this research was to investigate the interaction phenomena of rock and types of rock bolts to develop design principals for using grouted roof bolts. The investigation was to determine the effectiveness of grouted bolts in resisting lateral displacement and axial separation along fracture planes, and also to determine if grouted bolts eliminate the axial tensile stress near the anchor and the resulting rock fracture. The first year's effort involved defining the post-tensioning response of grouted bars and determining the amount of shear resistance generated by conventional and resin-grouted bolts. A finite-element analysis showed that if the rock and resin grout behave in an elastic manner, the post tensioning of a grouted bar will affect mine roof stability only if movement occurs near the collar. An experimental shear test program revealed that both conventional bolts and resin-grouted reinforcing bars significantly increase shear resistance along fracture or bedding plane when the average normal compressive stress on that plane is low (in the order of 25 psi) and when the bolt is oriented so that the shear displacement tends to lengthen the bolt. An increase in shear resistance is also noted at the higher normal pressure of 250 psi; however, the increase is small compared to the corresponding shear resistance without a bolt. Conventional bolts oriented so that they tended to loosen with shear displacement added no significant shear resistance.

Jan 1, 1974

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By Anthony D. Szpak

The purpose of this program was to demonstrate the feasibility of Illuminating various types of underground coal mining machinery as required by the Federal Coal Mine Illumination Standards Part 75.1719 to 75.1719-4 Code of Federal Regulations Title 30. Nine various machines were illuminated and the illumination systems were evaluated for a 3 month period of operation. Factors evaluated were ease of implementation, reliability, ease of maintenance, acceptance by mine workers and operators, Illumination degradation and durability.

Jan 1, 1981

By Robert L. Lagace

The purpose of the work reported herein was to investigate whether available telephone multiplexing equipment offered a means to rapidly upgrade the traffic-handling capacity of present mine telephone systems and provide for selective calling for safer and more efficient mine operation. Common sense was used to decide whether or not an item could be termed "available." Since conventional telephone gear is not designed to interface pager phones for example, existing shelf items would require adapters to compatibly interface these two types of gear for independent operation over the present single twisted pair used in mines. These and similar small items were allowed, but if a system required any extensive design work to adapt it for the mines, we ruled it "not available."

Jan 1, 1975

By John J. Ginty

The objective of the work reported herein was to evaluate state-of-the-art repeaters used in wireless communications to determine their suitability for use in extending the range of portable and mobile communications in underground mine applications. The scope of the work included wireless repeaters in the frequency range from LF (500 kilohertz) up to the one giga-hertz range. These repeaters included not only single-channel repeaters, that is F1/F1 repeaters for short range simplex party line communications, but in addition, F1/F2 type repeaters currently commercially available in the HF, VHF and UHF bands.

Jan 1, 1975

The analysis of in-mine grounding systems began with an extensive literature search which is still in progress. About a dozen articles have been found which deal directly with grounding problems on low voltage power systems or mine power systems. These systems have special grounding problems because normal load currents can be nearly as large as many types of fault currents. Information has been collected on the influence of cable spacing) conduit geometry, location of nearby conducting structures, etc., on the magnitude and path of fault current. Many other articles have been found which are less directly related to mine ground system analysis. The in-mine ground system analysis team has also inspected portions of two mine power systems to become familiar with the practices used in grounding. One electrical engineer and several other mine personnel have been interviewed concerning mine power system grounding practice. Already several aspects of the mine grounding system have been marked as requiring special attention.

Jan 1, 1975

By Ferdinand Roehlich

An evaluation of the use of manually activated, installed,. dry chemical fire protection systems on underground metal and nonmetal mine vehicles is described. In addition, an assessment of the possible health risks posed by the dry chemical extinguishing agents used in such systems is provided. Work involved installation of fire protection hardware on an operating piece of underground metal/nonmetal mine equipment and, via actual fire tests, a determination of the effectiveness of the hardware in extinguishing on-vehicle fires. Two fire protection systems were installed on a Caterpillar 988 front-end loader in St. Joe Mineral's Fletcher mine, near Viburnum, Mo. Both a fully pressurized Safety First CM-20 and a nonpressurized cartridge actuated Ansul A-101 were installed for comparative purposes. Both systems operated satisfactorily during an 8-month endurance trial period which preceded the actual fire tests. Each system was able to extinguish an 18" x 4" class B test fire placed in the engine area of the machine. The health hazards analysis of dry chemical powder consisted of a detailed search of published literature relating to these multipurpose agents. This data was verified via a controlled laboratory analysis of two monoammonium phosphate based powders (Safety First Unikem and Ansul Forey) and an analysis of air samples collected at various locations on the test vehicle during the fire tests. Although the powder was found to be nontoxic, two potentially dangerous thermal decomposition products were identified--ammonia and phosphoric acid. However, later analysis indicated that an operator would not be exposed to dangerous concentrations of either compound if he were to remain outside of the powder cloud. A "Selection and Use Manual for Manually Activated, Fixed Fire Suppression Systems on Underground Metal and Nonmetal Mining Equipment" was prepared both as an, appendix to the report and for distribution under separate cover.

Jan 1, 1977

By Richard G. Stearns

Extensive thick lignite apparently lies within 250 feet of the land surface in Dyer, Lake, Lauderdale, Obion and Tipton counties. Information on geology, land use, soils, groundwater and instability is compiled, along with a bibliography. A test and monitoring site was investigated at Fort Pillow Prison in Lauderdale County. Analyses were made of lignite, overburden, associated water and leachate. Lignite has high BTU (about 7800) and low sulfur (1.1% avg.). A year or more of data are presented on rainfall, water levels, and chemistry of surface water, groundwater, leachate and water from test pits. Main potential environmental problems are quality of surface water, and possibly shallow groundwater. The main aquifer of the region will likely be un-affected by mining. Low transmissibility of shallow aquifers will minimize lowering water levels of wells. Soil reclamation and conservation should be readily accomplished, Dangerous earthquakes have a low probability and mines are not significantly more hazardous than steep bluffs.

Jan 1, 1981