Search Documents

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Data obtained under controlled test conditions using a microbit drilling machine showed that oil emulsified in water muds may either increase or decrease the drilling rate, depending upon drilling conditions. A low-viscosity oil such as diesel fuel can give drilling rates in limestone almost equal to that of water. Data obtained for water emulsified in oil muds showed little decrease in the drilling rate in water-saturated cores as the water percentage of the mud was increased above the 5- to 10-percent range. Changes in drilling rate were found to be dependent upon the oil or water concentration of the mud and upon the type of formation drilled. Changes in static filtration on paper (API filtrate) did not correlate with filtration while the mud was circulated across rock. INTRODUCTION Oil additions to water muds have been reported to increase drilling rates, provide hole stability and improve filtration control. Eckel' showed that water-base emulsion muds used in the West Texas area increased drilling rate with increasing oil concentration up to 15 percent oil by volume, but drilling rate decreased at a concentration of 20 percent by volume. Based on laboratory tests using water muds to drill shale, Cunningham and Goins' reported that drilling rates increased and tendency for the bit to ballup decreased with the addition of oil. Percentage increase in drilling rate varied with the particular formation. They showed oil additions to improve drilling rates ap proximately 75 percent in Vicksburg shale and as much as 150 percent in Miocene shale. Each investigation showed an optimum oil content for the particular formation. Most data that indicated improved filtration control due to oil additions were based on static API Eltrates through paper rather than dynamic filtration through permeable rocks. Some types of dynamic test give a better representation of filtration down-hole while drilling and might be more likely to show some correlation with drilling rate. Static filtration would be important, of course, in relation to hole stability and formation damage. This laboratory's drilling tests, conducted on water-raturated Berea sandstone, indicated that improvements in drilling rate were not evident with increasing oil concentration in water-base muds. Investigation also showed similarity between oil-emulsion (water-in-oil) muds and water-emulsion (oil-in-water) muds while drilling these formations. In Lueders limestone high concentration of water-in-oil muds and high concentration of oil-in-water muds provided the same relative drilling rates. In Berea sandstone there was a large reduction in relative drilling rate with both the oil and water muds that contained low percentages of emulsified fluid. Dynamic filtration rates of water muds on rock did not always decrease with increasing oil percentages even though the static API filtration rates on paper did decrease. Data observed in laboratory drilling of limestone and sandstone indicate that improvements in field drilling operations when water- or oil-emulsion muds are wed may not be the result of increased drilling rates but of improved hole conditions. In some cases, actual drilling rates might be slower but improved hole conditions will result in less total time on the hole. DEFINITIONS Mud pressure—Pressure of drilling fluid as measured after leaving the drilling chamber. This is considered as the approximate mud pressure just past the bit and at the face of the formation. Terrastatic pressure—Pressure representing weight of overburden. Formation pressure—Pressure of formation fluid as measured at outlet of drilling chamber. This is considered as approximate pressure of fluid in the pores of the formation. Differential pressure—Difference between the mud pressure and formation pressure. Relative drilling rate, percent—Drilling rate with experimental fluid divided by drilling rate with water times 100 equals percent. LABORATORY EQUiPMENT AND TESTING PROCEDURES The drilling equipment has been described in previous publications The microbit drill is a closed system (capacity, approximately 7 gal) that can be pressurized to 15.000 psi and heated to 500F. Main components are a drilling chamber, filter-heater, rotary-drive and variable-speed cir-

By S. Gstalder, J. Raynal

Consideration was given to simple tests which could be performed on rocks to give a measure of rock drillability. Various methods of breaking rocks were considered and the hardness test developed by Schreiner was selected for this study. The test involves application of an increasing load on the rock face through a flat-faced cylindrical punch until rupture occurs. Test results show that hardness is a good measure of the breaking strength of rocks. Useful relationships are shown to exist between hardness and other physical quantities such as specific disintegration, Young's modulus and sonic velocity. Specific disintegration (volume of rock broken per unit of work input) provides a possible means of comparing the effectiveness of other methods of rock breakage. The relationship between hardness and sonic velocity may be very significant for it may be possible to deduce rock drillability from sonic log data. provided that a mineralogical factor is taken into account. TO test further the results of the work, laboratory drilling tests were performed which closely simulated down-hole pressure conditions. Correlations of drilling results with rock hardness measurements were quite good. It was concluded that rock hardness, as measured in the laboratory or as deduced from sonic logs, could be used in relations for predicting rock drilling performance. INTRODUCTION Drillability of rocks cannot be defined in an absolute manner by a single quantity or measured by a single test. Resistance of rock to drilling depends to a large extent upon the means used for rock destruction. This complicates drillability classification of rocks for there may be as many classifications as there are methods of rock breakage without known functional relations between them. The objective of this work was to develop. in terms of rock destruction behavior, means of selecting the best drilling method for a given rock or the conditions for optimum output from a given drilling method. ANALYSIS OF ROCK DESTRUCTION TESTS Gauthier and Baron' have reviewed the many test methods which have been developed for determining the resistance of rocks to breakage. These include drilling tests, punch tests, scratch tests, resistance to shock, wear tests, etc. A standard drilling test might be to determine the time required to drill a standard depth (1/16 in.) in a rock using a bi-cone microbit (1 1/4-in. diameter) when a standard load (417 Ib) is applied at a standard speed of bit rotation (110 rpm). From the standpoint of similarity, the results of microbit drilling tests would seem to be most representative of the several methods suggested above. However, evaluation of drilling performance by this method is only qualitative and cannot be applied directly to actual drilling conditions. Punch tests basically measure rock hardness. Punches of various shapes and sizes, including small cones for Vickers' and Knoop's tests, the wedge for Epstein's test and the right circular cylinder for Schreiner's test, have been used. Results of these tests lead to a quantitative hardness classification which would seem to be related to the resistance of rock to bit-tooth penetration. Scratch tests are related to the resistance of rocks to abrasion such as would be encountered in drilling with diamonds. Either the width of the scratch obtained at a fixed load or the load required to give a scratch of a fixed width may be used to evaluate surface hardness of the rock. This should be related to the resistance of the rock to wear. The above tests, and probably many others. give relative measurements of the breakage or destruction characteristics of rocks. There is no direct relation between results of these tests and the drillability of rocks. Also, the tests each measure different quantities which have different dimensions and they do not permit direct comparison of numerical values. As one step in rectifying the above difficulties. it is proposed that the results of all test methods be expressed in terms of volume of rock destroyed per unit of work required; this is referred to as "specific disintegration". Test results may then be reported in a form which shows both a classification of rocks in regard to each method and a comparison of methods with regard to each rock. The disadvantage in using specific disintegration is the difficulty of measuring this quantity with accuracy. The volume of rock damage is difficult to measure. as is the true value of work input. Rock heterogeneity adds to the

Jan 1, 1967

By K. E. Gray, G. M. Myers

In previous publications,5 results of single-blow bit tooth impacts on saturated rocks at various stress states were reported. This paper extends these earlier works to include study of bit impact tests on salt water-saturated Berea and Bandera sandstone samples under conditions of elevated confining and pore pressure. During the tests dynamic filtration and deposition of a mud cake were occurring due to the presence of drilling mud in the borehole and a borebole-to-formation pressure differential. Results indicate that saturation of these sandstones with salt water tends to make them weaker than when saturated with nonreactive fluids. Plastic failure often occurs even when extremely high fluid-loss muds are present in the borehole. The failure mode tends toward plasticity with decreasing fluid loss. Brittle failure of sandstones in mud-filled holes is apparently relatively rare. Depending on the stress level, and the associated failure mode, withdrawal of the bit tooth induces a tensile force that seems rather important relative to the quantity of rock removed by vertical tooth impact. INTRODUCTION A vast majority of the oil wells drilled today involve the use of colloidal muds having a measurable mud filtrate loss. It is known from field experience that reduction of the water loss of a mud generally results in a reduction of the penetration rate. This paper describes an investigation of crater formation at simulated bottom-hole pressure conditions for drilling fluids having different water losses. The literature on single bit tooth impact (cratering) at atmospheric conditions is extensive, but only a limited amount of work has been performed at the stress conditions similar to that found in oil wells. Spherical penetrator cratering tests on rocks at hydrostatic pressure were performed by Payne and Chippenda1e.1 Chisel impact studies on limestone with independently varying overburden and borehole pressure and atmospheric pore pressure were reported by Garner, et al.2 Gnirk and Cheatham3 performed "static" penetrator tests on dry rocks at equal overburden and borehole pressures. Podio and Gray4 studied the effect of pore fluid viscosity at atmospheric pore and borehole pressures and varying overburden pressures. Their results illustrated the importance of fluid saturation of the rock. Yang and Gray5 reported single tooth impact tests on saturated rocks at elevated borehole, pore and confining pressures, but with equal pore and borehole pressures. For the work reported in Refs. 4 and 5, filtration across the hole bottom purposely was avoided. Maurer6 has investigated the effect of independently varying pore and borehole pressures at elevated overburden pressures by using a zero water-loss mud in the borehole. His tests were carried out under conditions that allowed independent control of overburden, pore and borehole pressures, but without control of filtration at the hole bottom. EXPERIMENTAL APPARATUS AND PROCEDURE APPARATUS The single blow chisel impact apparatus used by Garner,2 as modified for this study, is shown in Fig. 1. A cross section of the pressure vessel is shown in Fig. 2. Several pieces of auxiliary equipment were added to the original apparatus in order that the borehole and pore pressure could be applied in a manner analogous to the actual bottom-hole situation. The pore-pressure system included a filtrate volume-measuring transducer and had sufficient surge capacity to allow filtrate to be injected into the sample without significant changes in pore pressure at points remote to the borehole. The borehole-pressure system contained a cross connection to the pore-pressure system so that both systems could be pressured simultaneously. The borehole-pore pressure differential was applied rapidly by the use of a quick and full-opening valve. The operation of this valve triggered two industrial

Jan 1, 1969

By J. B. Cheatham

Applications of the mathematical theory of plasticity promises to lead to the solution of many drilling and rock mechanics problems. ,Because of mathematical considerations, the inelastic behavior of rock has frequently been represented by a perfectly plastic model in conjunction with a yield criteria of the Coulomb or Mohr type. The totality of all stress states for which a solid ceases to behave elastically can be represented as a limit surface in stress space. ,Probing of such limit surfaces indicates details of strain hardening which are not provided by the standard triaxial testing procedure. Probing tests of the limit surfaces have been performed on Cardova Cream limestone to provide data for extending plasticity theory to cover situations in which consolidation and strain hardening are present. Test results indicate that this highly porous limestone undergoes a permanent volume decrease when it is subjected to hydrostatic pressures in excess of 3,500 psi. A virgin sample tested under a confining pressure of 1,500 psi has a yield strength of 1,700 psi; however, if the sample is subjected to a consolidation pressure of 5,000 psi, before testing at 1,500 psi, the yield strength is raised to 2,300 psi. Thus, both consolidation and strain hardening are important considerations in describing the mechanical behavior of this limestone. Tests conducted with the axis of the core having different orientations indicate that this rock is also anisotropic. Portions of the initial and subsequent limit surfaces are determined for samples loaded either perpendicular or parallel to the bedding planes. INTRODUCTION Previous experimental work in rock mechanics indicates that no mathematically tractable constitutive theory is inclusive enough to describe the mechanical behavior exhibited by all types of rocks under all conditions of stress and temperature. Indeed, the type of deformation encountered in a single type of rock is known to depend upon the stress and temperature conditions in the rock during deformation.l-5 Certain rocks and minerals, notably those minerals composed of ionic salts, have been shown to exhibit plastic deformation when tested under conditions of high confining pressure.2 Since the mathematical theory of plasticity provides simplifications over the theory of elasticity in certain types of problems, such as those in which limit analysis can be applied, it is of interest to know under what conditions plasticity theory may be applied to rock mechanics problems. The following factors determine the nature of the deformation a particular specimen will undergo: (1) the microscopic structure of the rock, i.e., the structure visible under an optical microscope, including number of phases, porosity, distribution of phases, (2) the mineralogical structure of the solid phases, (3) the conditions of stress and the rate of change of stress and (4) the temperature. Extensive experiments on Yule marble, Carthage marble, Solenhofen limestone and other calcerous rocks indicate that these relatively nonporous rocks deform plastically under certain conditions of loading, and creep under other conditions of loading.l-3 This study is concerned with the behavior of Cordova Cream limestone (Austin chalk) which is also composed almost entirely of calcite and thus has the same mineralogical composition but, because of a rather large porosity, it possesses a different microscopic structure. This investigation was undertaken to learn if Cordova Cream limestone deforms plastically despite the embrittling effect of the pore spaces, and to provide data which can be used to determine whether the mathematical theory of plasticity can describe the mechanical behavior of Cordova Cream limestone. A brief discussion is given of some of the underlying principles of plasticity theory concerning stress space and limit surfaces. Strain hardening is defined and a discussion is given of how the mechanical behavior of a material can depend on the previous history of the loading. This is followed by a description of the experimental procedures

By A. A. Toprac

The recurring problem of joint failures in ofjshore structures, coupled with the catastrophic collapse of many of these structures during Hurricane Hilda (1964), hay forced reconsideration of techniques presently used to design sfuctural joints. This paper presents results of studies conducted for this reconsiderat?on. Only right-angled T-joint,s and cross-joints where a brace was welded directly to the undisturbed surface of another tube (the chord) were considered. Tests were performed on seven T-joint and 12 oross-joint specimens of two types which were designed to give a broad but practicd range to the geometrical parameters believed to be of significance to the problem. These paramefers were expressed in dimensionless form. Each specimen of the T-joints was instrumented wirh both electrical resistance strain gauges and deflection dials. After the elastic tests were concluded, each specimen was loaded to failure by applying an axial tensile load to the brace. The cross-joints were tested to failure without measuring elastic strains. Theoretical solutions for the stresses in a cylindrical shell due to a distributed radial load over portions of its surface were numerically evaluated. The experimental results are compared with calculated values obtained using Bijlaard's and Dundrova's theoretical analyses. INTRODUCTION During the last IS years a large number of structures were built for the offshore exploration of oil both in the Gulf of Mexico and dong the Pacific Coast.' In all these offshore platforms, the tubular shape was extensively used since this shape provides outstanding strength in proportion to its weight, compared to other shapes, when all directions (x, y, z) are considered. Past use of tubes was hampered because of connection details. But with the advent of welding, it became no more difficult to connect tubular shapes than to connect rolled shapes. However, some problems have been encountered in actual construction in making welded joints that are adequate and yet economical. In trying to connect tubular members, designers have used a varied number of methods; consequently, some of the joints seem to be very expensive in detail while others appear weak and underdesigned. An inspection of offshore platforms owned by different companies indicates the use of a large number of joint arrangements and configurations. Such a variety of joint types in current service indicates the wide divergence of opinion that exists on how such joints should be designed, stiffened and strengthened. Fig. 1 shows the various types of connections that have been used in practice. This paper reviews the present state of art on tubular joints of the T and cross type, and presents results of experimental and analytical work being conducted at The U. of Texas and elsewhere. It is believed that such information will be of great help to designers for the formulation of proper design procedures for joints. CONNECTION PROBLEM Recently, cracks have been observed in several welded connections in offshore structures. Fortunately, until about 1 1/2 years ago, these failures have been localized and have not resulted in the collapse of structures or loss of life. For example, one platform installed in Louisiana during 1955 in about 60 ft of water had been subjected to four tropical hurricanes. This platform successfully withstood these forces and was later removed because operations at this location had been completed. Many joint failures were observed during the removal.

By L. R. Raymond

With the trend toward deeper and consequently hotter holes, measurements of drilling mud properties at atmospheric temperatures are becoming increasingly inadequate.' Both the prediction and control of down-hole mud properties depend in part upon our knowledge of temperatures in the wellbore. Consequently, a better understanding of factors that affect temperatures during circulation and trips could improve drilling operations. It was toward the goal of obtaining this understanding that this study was directed. Other investigators2 have studied the response of fluid temperature in the borehole during trips. However, all of these studies have used an assumed formation temperature profile at the conclusion of circulation and have provided no means to calculate this profile directly. In this study, the formation profile during circulation was calculated. Other investiga-tors3-5 have also studied bottom-hole temperature during circulation. However, they have developed neither general techniques for calculating the entire temperature profile in the system nor generalized methods for predicting bottom-hole fluid temperatures during circulation. Such techniques and methods have been developed and are discussed briefly in the following pages. Temperature Behavior During Circulation Circulation of fluid during the drilling operation is represented schematically in Fig. 1. The process of circulation has three distinct phases: (1) fluid enters the drill pipe at the surface and passes down the drill pipe; (2) fluid exits the drill pipe through the bit and enters the annulus at the bottom; and (3) fluid passes up the annulus and exits the annulus at the surface. To simulate the thermal behavior of the fluid in the system, each of the phases of circulation must be described mathematically. In Phase 1, the fluid enters the drill pipe at a specified temperature, TDo. As the fluid passes down the pipe, its temperature is determined by the rate of heat convection down the drill pipe, the rate of heat exchange between the drill pipe and the annulus, and time. Phase 2 of the circulating process merely requires that the fluid temperature at the exit of the drill pipe be the same as the fluid temperature at the entrance of the annulus; i.e., TD(L,t) = TA(L,l). Thus in Phase 3, the fluid enters the annulus at TD(L, t). As the fluid flows up the annulus, its temperature is determined by the rate of heat convection up the annulus, the rate of heat exchange between the annulus and the drill pipe, the rate of heat exchange between the formation adjacent to the annulus and the fluid in the annulus, and time. These rates of heat exchange and the time dependency of mud temperature are described by well known heat-flow equation.6 Consequently, as shown in the Appendix, the temperature profiles in the drill pipe, annulus, and formation can be obtained by solving Eqs. 1 through

Jan 1, 1970

By K. C. Strebig, C. W. Schultz, A. A. Selim

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory. The drill was designed to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation and an equation representing the bit performance was derived from the mathematical theory of reliability. The drilling torque was found to increase with the use of additives while the sliding coefficient of friction and the wear coefficient decreased. The energy per unit volume consumed was found to increase with the use of additives. A hypothesis explaining the effects achieved with the additives is given. INTRODUCTION For some time researchers have attempted to increase drilling efficiency by adding certain agents to the flushing medium. Much of this interest is the result of the observations of Rehbinder, Shreiner and Zhigach1 They postulated that "...in processes for the mechanical destruction of solids, a region of increased crack formation is created in the deformed layers adjoining that surface of destruction, forming the predestmction zone. The surrounding medium (for example, a liquid) which wets a given solid will penetrate the embryo microcracks of the predestruc-tion zone. Increasing the molecular affinity of this liquid for the surface of the solid considerably facilitates the deformation and destruction by softening the solid in the zone of increased crack formation. In this manner, the hardness or strength of the deformed body is decreased by the influence of the penetration of the liquid into the predestraction zone." This is known as the "Rehbinder effect". Rehbinder's work has prompted many investigators to examine the effect of additives on the mechanical destruction of rocks. Engelmann, Terichow and Selim reported that the maximum penetration of the rock by a diamond point in a solution environment was at the isoelectric point of the solution.* Robinson reported that his results did not appear to support the theory of Rehbinder.3 Joris and .McLaren suggested that additives with surface tension lower than water will be more efficient in cooling the diamonds.4 Their effectiveness in removing the fine cuttings from the face of the bit will also improve the efficiency of the system. They reported an improvement in impregnated bit life and penetration rates with the use of soluble oil additives. In contrast, Long and Agnew, drilling with surface set bits, reported that lubricating agents increase bit temperature and wear.5 A significant change was reported6 in the mechanical properties of rock with polar additives. It was concluded that this change in the mechanical properties of the rock in the presence of the additive is due to the rock hydrophilic properties. Ethylene glycol, glycerine and anionic detergent were selected for this investigation because their surface tension is lower than that of water. The surface tension of these additives for the concentrations studied was 42 to 75 percent of the surface tension of water. A low surface tension additive would wet the surface of the diamonds more easily and hence would be more effective in cooling the diamonds. Another characteristic of these low surface tension additives is their effectiveness in removing the cuttings and preventing the flocculation of the formed particles in the drilling process. This article summarizes the results of an investigation performed at the laboratories of USBM, Twin Cities Mining Research Center. The objective of the investigation was to study the over-all effects of some organic additives on the performance of diamond impregnated bits in atmospheric drilling conditions only and not in downhole pressured conditions.

Jan 1, 1970

By J. B. Cheatham, M. D. Biggs

This paper presents a systematic method for determining the forces on a simplified roller bit. The kinematics of an actual roller bit drilling in rock is complex; nevertheless, it is desirable to obtain an accurate analytical model.. As a preliminary study, the roller bit is represented here by a simple two-dimensional bit and the rock by a Coulomb plastic material. Results from previous work, plus additional assumptions, are incorporated into a computer program to determine the forces required to move the bit in a specified manner. Example problems are worked by use of this program. By studying similar drilling problems and by supporting laboratory work, one could eventually obtain an accurate analytical model for drilling by an actual roller bit. This could lead to the compilation of a catalog of results that, in turn, would allow selection of the optimum drill bit for any given situation. INTRODUCTION

Jan 1, 1970

By A. Lubinski, W. D. Greenfield

Bumper subs are currently used in offshore operations to permit a constant weight to be carried on the bit while drilling, regardless of the vertical motion imparted to the drill pipe by drilling vessel heave. As shown in this paper. the vertical motion of the lower end of the drill pipe (the bumper sub end) may be appreciably greater than the vessel heave. Therefore, the necessary stroke of bumper .rubs for successful operation is greater than thought in fie past. Also, there is an appreciable tendency of the drill pipe to buckle above the unbalanced type of bumper sub. Thus, more drill collars than previously used should be carried above unbalanced bumper subs to keep drill pipe straight. INTRODUCTION Drilling bumper subs are placed in the drilling string for various reasons. This paper is concerned with their use only as an expansion and contraction joint while drilling from a floating rig. In this application the bumper subs are normally located just above the drill collars and their function is to allow the driller to maintain accurate weight control on the bit regardless of up-and-down movement of the drilling vessel. This paper analyzes the effects of bumper subs on the drilling string and presents recommendations for their future use. When subjected to vertical oscillations, the drilling string behaves like a long, distributed system of mass and spring. The magnitude of vertical motion at the bumper sub is always greater than the heave of the drilling vessel due to the dynamic reponse of the drilling string. The ratio of these motions increases with the length of the drilling string, and may reach values of 1.5 or even 2 with strings 16,000 ft long. Thus, the total travel required in bumper subs can be considerably more than the motion of the drilling vessel. Lack of knowledge of this fact could have contributed to problems previously experienced with bumper subs. This fact can also lead to fatigue problems in the drilling string for very deep wells. Satisfactory operation should be obtainable whether hy-draulically balanced or unbalanced bumper subs are used in the drilling string. Theoretically, the balanced sub is preferable since its use does not require placing drill collars above the bumper sub to prevent drill-pipe buckling, an inherent characteristic of the unbalanced bumper sub. The current method of calculating weight of drill collars required to prevent helical buckling of drill pipe above unbalanced bumper subs is erroneous. Placing drill collars above the sub to prevent drill-pipe buckling has the same effect on dynamic response as increasing the length of the drilling string by an equal weight of drill pipe. Thus, total travel required in the subs is increased. Means for calculating the correct weight, which is much greater than previously thought, are given in this paper. BALANCED VS UNBALANCED BUMPER SUBS A drilling bumper sub is essentially a telescopic joint capable of transmitting torque at every position of its stroke. Thus, it allows the operator to isolate the weight of the drilling string from the weight of the drill collars above the bit. This permits the driller on a floating rig to maintain accurate control over the weight on bit — a control that is unaffected by vertical motion, due to wave and tide action of the drilling vessel. UNBALANCED BUMPER SUBS The unbalanced bumper sub is simply a splined tele~copic joint (Fig. I). Ordinarily, this arrangement will operate satisfactorily, but the presence of drilling fluid under pressure results in a pressure force that acts downward on the drill collars and bit, tending to open or extend the bumper sub. This downward force is equal to the pressure drop across the bit times the area indicated by diameter d2 in Fig. 1. Denoting this force by Fd, and the pressure drop across the bit by ?p yields Fb = (p/4)d22(?P) .........(1) There is also an upward-directed force given by Fu = (p/4) d22-d21)(?p) .......(2) which puts the drill pipe immediately above the bumper sub in compression, resulting in helical buckling. However, buckling is actually more severe than expected in that buckling occurs as if the compression were equal to Fd, rather than to Fu. This surprising phenomenon is well known as far as tubing is concerned;1-3 but, in contrast with the case of tubing, this force may shorten drill pipe only a few inches. Thus, this cannot explain the operating difficulties that sometimes have been encountered. However, having the drill pipe in compression and helically buckled is contrary to current practice; therefore, drill collars whose weight in mud is equal to the force Fd should be added above the bumper sub. Since the value of Fd depends on the pressure drop across the bit, the

By Olaf Hondrum

CHURN drilling equipment at Bagdad consists of two Bucyrus Erie 27-T model drills and one 22-T drill with gasoline engines. The drilling tools weigh approximately 1600 lb. The holes are drilled with 7-in. bits which are heated in an oil burning furnace and sharpened in an electrically powered bit sharpener. A service truck brings the bits to the drills and takes the dull bits back to the shop. The bits weigh around 250 lb. when new and are handled by drill crews without any mechanical handling device. When the management decided to start open- pit operations in 1945 the ruggedness of the terrain was one factor that led to the purchase of the small 22-T model drill. The orebody lies on both sides of Copper Creek Canyon. The sides of the canyon are steep and are cut by numerous narrow branch gullies. The drill had to travel over roads that were narrow and steep. It proved adequate for drilling the capping formation and is still in use.

Jan 1, 1950

By McIntosh A. H, Torlach J. A

Since the last paper on mining methods was presented to the Annual Conference of the Australasian Institute of Mining and Metallurgy in 1:960, numerous advances have been made in drilling and blasting techniques at Mount Morgan. This paper describes the drilling and blasting methods being employed in the open cut. The change over to track mounted percussion drills for all types of primary drilling is almost complete and new techniques such as detergent drilling and pressure loading of ANFO are being applied successfully.

Jan 1, 1965

By T L. Horsley

This paper deals with the drilling and blasting methods employed at the Cassiar mine, which is located just south of the B.C.-Yukon border. It covers both the "pit" and "peak" mining operations. Specific problems, such as working in frozen ground, are discussed, and the breaking characteristics of the various rock formations are outlined. The paper concludes with a brief mention of the equipment used in the operation, as "~ell as an outline of the breaking costs. Introduction T HE Cassiar asbestos mine is located just south of the British Columbia -Yukon border high on a spur of McDame mountain. Chrysotile asbestos fibre occurs in a faulted enlargement of a serpentine sill lying conformably be-tween a series of sedimentary beds and volcanic flows which dip at 45 degrees into the mountain. One end of the orebody is eroded by a cirque in which a layer of permanently frozen ore and waste talus lies at the end of the mining benches. The topography at the mine is steep, with no flat areas. Roads, dumps, and areas for crushing,

Jan 1, 1965

By J S. Kermeen

This paper deals with drilling and blasting techniques at the Phoenix mine, near Grand F1nks, B.C., which is now operated by The Granby Mining Company Ltd. The difficulties of open-pit mining through former underground workings are unique to this operation. Rock types are related to drilling conditions, and the methods used, or contemplated, to overcome the several difficulties are outlined. The equipment used is also mentioned. Finally, blasting techniques and costs are reviewed. Introduction T HE Granby Mining Company operates on open-pit copper mine and concentrator at the site of the original Phoenix mine, near Grand Forks in south-central British Columbia. The pit is a side-hill cut measuring approximately 1,000 by 2,000 ft., and covering a vertical range of from 4,550 to 4,950 feet above sea level. The mill is currently operating at 1,900 tons per day. A 4.5 to 1.0 waste to ore ratio necessitates the removal of some 15,000 tons of ore and waste per working day. Mining conditions at Phoenix are extraordinary in that all the ore zones currently being

Jan 1, 1965

By D. C. Foote

MR. FOOTE: This paper deals with blasting and mechanical loading. The Union Pacific Coal Company does all of its blasting with permissible powder and electric shooting, but this paper deals principally with blasting in connection with mechanical loading. With the introduction of mechanical loading into the coal fields of southern Wyoming one of the main problems to be taken into consideration was the drilling and blasting of the coal. The methods used in blasting coal for hand loading were found to be ill adapted to the mechanical practice, so numerous tests were conducted from time to time to determine a system or systems whereby the coal might be blasted in a form to be easily handled by the loading units. The general practice in blasting coal for hand loading, for example in a room 24 feet wide and seven feet high with an undercut of seven feet, would be to shoot one or two strong breaking shots in the center and one on each rib. While much of the cut would be blasted down in good lump, some coal would be left hanging at the back and ribs. With hand loading, the miners would have time to pull this coal down with a pick between cars and eventually would clean up the place ready for the cutting machine. The loading machine, however, cannot get this coal down and its operation would be delayed while the men were doing the necessary pick work.

Jan 1, 1929

Drilling and blasting are an essential part of most mining operations, and are commonly major operating cost centres. The effectiveness of blasting can have a significant influence on all subsequent activities, and hence overall operating costs. Drilling and blasting systems must be compatible with the overall mining method, to minimise total costs and ensure operational efficiency. Selection of suitable equipment and techniques requires an understanding of the total operation, plus current skills in specialised technologies. This paper examines the contribution of drilling and blasting to total costs, including the balance between capital and operating costs. The use of computer modelling is discussed, to demonstrate how blast performance and costs can be predicted and alternatives analysed. Case studies illustrate how cost savings can be made in operating mines, and alternative systems evaluated to optimise new projects.

Jan 1, 1990

By D. Scott Scovira, Remi Proulx

The Meikle Mine is a high grade, underground gold mine utilizing primary-secondary longhole open stoping with delayed backfill to produce 3000 stpd of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 330” F were measured. In the early stages of mining, the mine experienced premature detonations using different explosives. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By R. P. Proulx

The Meikle Mine is a high grade, underground goldmine utilizing primary-secondary longhole open stoping with delayed backfill to produce 2700 tpd(3000 stpd) of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 166°C (330°F) were measured. In the early stages of mining, the mine experienced premature detonations using different explosive products. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By E. D. Gardner

Open-cut mining of copper ores in the western United States is a relatively new industry. At first the mining methods were mainly adapted from those used at open-cut iron mines and at quarries, but now efficient practices that are more suitable for the copper deposits have been developed. The pioneer in this field is the Utah Copper Co., of Bingham, Utah, which deserves great credit for working out much of the early procedure. Stripping began at that mine in 1906, and the large Garfield concentrator was put in commission in 1908. Next in order of development were the Nevada Consolidated Copper Co., at Ely, Nev. ; the Chino mine of the Ray Consolidated Copper Co., at Santa Rita, N. Mex. ; the New Cornelia Copper Co., at Ajo, Ariz. ; the Sacramento Hill mine of the Copper Queen Branch, Phelps Dodge Corporation, at Bisbee, Ariz.; and the open cut of the United Verde Copper Co., at Jerome, Ariz. The Sacramento Hill mine began to produce in 1923, and the United Verde open-cut mine has produced ore mainly in connection with stripping. The writer visited the Utah Copper mine in September, 1923; the Nevada Consolidated in August, 1923; the Chino in July, 1924; and the New Cornelia, the Sacramento Hill, and the United Verde open cut at various times during 1922, 1923, 1924, and 1925, mostly in connection with other work.

Jan 1, 1927

By Rob Farnfield, Ben Williams

The A5 road in the United Kingdom forms an ancient and well-used route through the hills and mountains of North Wales. In the 1990?s a programme of work was conducted to upgrade the road to modern standards. As part of this work a new cutting was constructed to bypass a portion of road routed through a gorge close to the village of Ty Nant. This new cutting was formed by drilling and blasting and included much pre-splitting and extensive rock bolting. This operation caused much concern to local residents relating to vibration, air overpressure and flyrock.

Jan 1, 2011

The Kennedy Siltstone Open Cut provides graded rock for stope filling. Rotary drilling of 310 mm blastholes with a Gardner Denver GD120 is used, and the successful application of an equilateral triangular drilling pattern is described. Charging practices and the development of bulk slurry handling are outlined. Blast monitoring plays an important role in K.S.O.C. drilling and blasting operations. The proximity of nearby residential areas (1300 m) and the Mount Isa Airport (4500 m) necessitates special attention with regard to the minimisation of both air blast and ground vibration levels. The application and control of drilling and blasting parameters has had a direct bear- ing on success of the mining operations and also played an important role in reducing the disturbance to the community.

Jan 1, 1978