Search Documents

By Galen Clevenger

THE losses of gold and silver occurring during the conversion of the precipitate, resulting from the cyanide process, into bullion may occur in two ways: first, there may be mechanical losses during the handling of the precipitate up to the time that it is charged into the melting furnace; and second, there may be losses after the precipitate reaches the melting furnace. Much of the loss during the handling of the pre-cipitate can be eliminated, and in fact, in modern plants this loss is known to be very small; particularly since preliminary acid treatment of the precipitate with the attendant extra operations has been abandoned in all but certain plants where gold predominates and this extra step is still deemed necessary. The losses in the melting furnace are from dusting and volatilization; losses in the furnace bottom and linings; floor sweepings; and slag and matte. The gold and silver in the: products which do not: go out of the flue are readily recoverable by standard methods, and while there may be considerable gold and silver tied up at times, the ultimate loss with careful "work should be small. The losses resulting from volatilization and dusting in connection with the melting of the silver slime from copper refineries have been determined by standard methods, and the possible recovery: definitely estab-lished through the installation and operation of electro-static precipitation units. This subject has not been thoroughly investigated in connection with the melting of`. cyanide precipitate; at least, there are no published accounts of such tests. Experiments have been made in the past to determine melting losses by weighing and assaying the precipitate, but this method gives results which are uncertain on account of the difficulty of accurately sampling and assaying cyanide precipitate. Attempts to ascertain these losses by bubbling a measured sample of the gas through cyanide solution or, other absorbent have likewise failed to give depend-able results.

Jan 1, 1922

By Cody Giroux, Homer Scurlock, Michel Wasag

Silica and Crystalline Quartz exposure continues to be a serious health threat to nearly 2 million workers in the United States, including more than 100,000 working in high risk jobs such as abrasive blasting, foundry work, stonecutting, rock drilling, quarry work, mining and tunneling. The primary focus of this study is to identify the best methodology to reduce particulate-laden air and limit/eliminate exposure to respirable dust with silica/crystalline quartz during tunneling operations. This study focuses on two de-dusting systems employed on similar tunnel construction projects. The first project is the Coxwell Bypass Tunnel located in Toronto, Ontario Canada. The second project is the Westerly Storage Tunnel located in Cleveland, Ohio. The Toronto project is utilizing a wet de-dusting system. The Cleveland project is using a dry de-dusting system. The objective is to determine which system provides the best protection and suitability to capture, remove and ultimately reduce respirable concentrations of silica/ crystalline quartz to safety and healthy levels in underground tunneling activities.

Jun 13, 2021

By Steven A. Bradbury

INTRODUCTION Passive dust control systems are quickly gaining acceptance in the bulk solids handling industries. The number of applications is increasing due to proven performance, especially in US power plants burning Powder River Basin coal. Air Control Sciences ®, Inc., of Boulder, Colorado, has over forty (40) patented Dustless Transfer ® systems in operation. All of the installations control workspace dust levels to less than 2.0 mg/m3, and in some applications reduced conveyor dusting by over ninety-eight percent (98%). Passive systems control fugitive dust emissions by minimizing the induced airflow in bulk material transfer and slowing its velocity. Traditionally, fugitive dust control in the mining industry was accomplished using either dust collection systems or dust suppression systems. The term passive dust control, indicates these methods don't use any active dust collection or suppression. Passive dust control systems are best suited to transfer from one conveyor to another. They can also be applied to transfers from feeder to conveyors.

Jan 1, 2004

"As stated earlier the primary goal of the Generic Mineral Technology Center for Respirable Dust is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. While initial work was directed to coal dust the charge to the dust center has been expanded to include diesel particulates and asbestosis, the latter of deep concern not just to workers in the mineral sector of the economy but also to the general populace.A major facet of Dust Center research has been the analysis and documentation of comprehensive research protocol and procedures that are appropriate state-of-the-art in the various areas of respirable dust. In addition to definition of standardized research protocols and procedures which would be utilized by center personnel for uniformity and reproducability there is a considerable need for utilizing standardized respirable dusts in experiments with consistent, reproducible characteristics which simulate those of actual mine dust. This respirable dust needs to be available in large quantities for a wide variety of research uses that include animal and medical experiments. The dust must be free of the lubricating oils and grinding wheel contaminants that are frequently encountered in laboratory generated dusts.The holistic approach to establishing standardized protocols and procedures applicable to the five major research areas of the center is presented in Figure 5.In one hypothesis, range in coal volatility is considered to be a major causal factor in the incidence and severity of pneumoconiosis. Therefore a suite of characterized standard respirable dust samples have been prepared for researchers from coals representing the western (high volitile A bituminous), central (medium volatile bituminous) and eastern (anthracite) mining areas of Pennsylvania. Quartz, limestone (rockdust) and kaolin clay samples, representing important mineral constituents of coal dust have also been prepared.A suite of medical investigations have been developed utilizing small and medium size animals as well as non-human primates in a variety of dust/lung interaction projects which will be discussed in the next section. A number of respirable dust sampling and dust generation methods have been investigated and selected techniques utilized for both in-mine and in-laboratory research investigations. These will also be discussed in more detail later. A wide range of respirable dust size, chemical and mineralogical analyses have been investigated, standardized and documented for use in various research investigations.This interaction and documentation of various respirable dust sample procedures, animal and medical tests, sampling and dust generation methods, plus size, chemical and minerological analysis applied in the five major areas of research investigation have served to create a very favorable synergism and rapid technology transfer in the respirable dust center."

Jan 1, 1988

By Mike Cammack, Logan Huppert, Gustavo Azpilcueta

During the summer of 2015, Unisea Inc. sought proposals for the G1 Dock Replacement Project in Dutch Harbor, Alaska. It would be a one year project and construction was scheduled to begin in the spring of 2016. One aspect of the project was the requirement for a layer of armor stone to protect part of the dock. An estimated 30,500 tonnes (37,670 t) of armor stone were needed for the project. The source of rock was the Unisea Quarry due to its proximity to the project and the quality of the stone meeting all the required technical standards.

Jan 1, 2018

By E. D. Kindle

"The Duthie mine is on the southwest slope of Hudson Bay mountain 7 1/2 miles west of Smithers, British Columbia. A good motor road about 15 miles long connects the mine with the Canadian National railway at Smithers. The principal workings are on the Henderson group of claims between elevations of 3,200 and 4,000 feet above sea-level. Silver, lead, and zinc were produced from this mine between 1924 and 1930.Three adit drifts known as the Compressor, McPherson, and Thompson levels were driven along the Henderson vein-lode in 1922, and the following year the operating company, known as Duthie Mines, Limited, shipped some high-grade silver-lead-zinc ore. Further shipments of high-grade, handsorted ore were made in 1926, and in 1927 a modern flotation-type mill was built, having a capacity of 50 tons of ore a day. Mining operations were suspended in March 1930."

Jan 1, 1954

Duval Corporation, the owners of the Sierrita, Esperanza, and Mineral Park copper operations in Arizona, first acquired the mineral rights to their Battle Mountain, Lander County, Nevada, property in 1962. Development of the mine commenced in mid - 1965, and the copper operation began at the end of 1968. The ore, a mixture of chalcocite and chalcopyrite, was milled and floated at a rate of 3, 175 mtpd (3,500 stpd). Because of low copper grade and price, the plant was shut down after about ten years of operation. Attention was then turned to an adjacent low-grade precious metal ore body which contained 2.74 g Au and 3.4 g Ag per mt (0.08 oz Au and 0.10 oz Ag) and minor amounts of copper. Test work revealed recovery by Carbon-In- Pulp treatment would amount to approximately 2.8 mt (90,000 oz) each of gold and silver per year. A rapid engineering and construction schedule resulted in the world's largest, as of late 1980, Carbon-In- Pulp plant being put on-stream in January 1979, with a capacity of 2.720 mtpd (3,000 stpd). Fortunately, the original crushing and grinding plant with all its infra structure was available, and the only modification needed was the addition of a gravity circuit to remove coarse free gold ahead of Carbon- In-Pulp treatment. One of the four primary 500 mm (20 in.) cyclone underflows in the primary ball mill circuit is directed to a secondary ball mill where its product is again cycloned. The cyclone underflow is screened at 3,360 microns (6 mesh) with the undersize being treated on two Pan American 1.07 m by 2. 14 m (42 in. by 84 in.) jigs. Hutch product is further concentrated on two Wilfley tables, a magnetic separator, and on a third Wilfley table where approximately 930 g (30 oz) of gold are recovered each day for amalgamation, retorting, and smelting. Returning to the grinding circuit, the final cyclone overflow is sent to the original plant tailings thickener to obtain proper pulp density for Carbon-In-Pulp treatment. Thickener underflow, at about 40% solids, is then conditioned with air and lime in a series of two 8.5 m by 9.75 m (28 ft by 32 ft) 15O cone bottom Pachucas for oxidation of pyrrhotite. The pulp is then split into two streams for cyanidation for 48 hours in two lines of eight Pachucas of the same size. Pulp is transferred from tank to tank by auxiliary air lifts. Cyanided pulp is then sent to a series of six C. I. P. mechanically agitated tanks with one hour retention in each tank. Originally these

Jan 1, 1981

By Yassine Lahmadi, Edoardo Trivellato, Christian Chereau, Bénédicte Robert

Within the framework of the adaptation of the South-East European Technicentre (Technicentre Sud-Est Européen TSEE), SNCF Voyageurs appointed Pini with the project management mission (MOE) for the design and construction monitoring of a road tunnel. This investment has a dual function: during the site transformation phase, it facilitates the work logistics (and shorten traffic flows); and in the operating phase, it is intended to ease all movements on the site over the long term. This is a limited-length gallery (50 meters) to be performed in conventional excavation below Poniatowski Avenue (Paris 12e). The excavation, crossing the entire width of the boulevard, constitutes a major challenge, given the very low coverage (less than 5.5 m), and the surrounding main infrastructures. The same project mis- sion includes the design of the tunnel accesses, via reinforced-concrete frame structures. The targeted design questions several aspects of its execution framework, and particularly, continuous operation must be guaranteed to the neighboring networks during the works. The installation of an umbrella- pipe all along the excavation profile, the progression in divided sub-sections, and the implementation of a complex monitoring system are hence key elements for limiting and controlling any deformation. An exhaustive 3D finite element modelling was performed, taking into account the detailed phasing of construction (pre-support, excavation in divided section, preliminary support and definitive lining), to dimen- sion the structures, and, overall, to analyze the impacts on the neighboring structures and facilities. During the execution phase (planned for mid-2024), monitoring activities with back-analyses as close as possible to the works are planned.

Jun 23, 2024

By Dennis V. D’Andrea, Joseph L. Condon

Laboratory crater tests were performed in two-dimensional plates and three-dimensional .blocks of Holston Limestone. Fractures in the blocks were exposed by sawing through the crater region, and a technique employing dye penetrants is described for examining the resulting fracture systems in both blocks and plates. Crater fracture patterns changed from extension of radial fractures to spa11 fractures parallel to the free face as charge depths were increased. The amount of fractured rock was found to be greater than the amount determined from standard crater volume measurements. Graphs and photographs illustrate these findings.

Jan 1, 1971

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By G. B. Walker

The success of Heavy Media Separation, the static sink-float process, is evidenced by the operation of an estimated 300 installations treating many millions of tons per year of a wide variety of mineral products ranging in value from gravel to diamonds. The static heavy media process is usually limited to the treatment of plus 1/4 inch material. Mr. Victor Rakowsky, who was largely instrumental in the development and application of heavy media separation, recognized the need for a new apparatus and process which would extend the application of heavy media into the finer size range without placing a restrictive limit on the top size of the feed. He recognized the requirement for the application of centrifugal force to augment the force of gravity in separating fines by sink-float techniques.

Jan 1, 1966

By Liang Wang, Sheng-Kai An, Bing Xie, Hong-Yi Li, Cui Li

In order to develop an environment-friendly method for extracting vanadium effectively from aqueous solution containing vanadium, the dynamic adsorption behavior of V by a continuous fixed-bed column which was filled with macro-porous weak base anion exchange resin was studied. Effects of conditions including the bed depth, flow rate, concentration of vanadium ions on dynamic V adsorption were investigated. The optimum adsorption conditions were established at flow rate of 6 ml/min with bed depth of 20 cm. Isotherms studies demonstrated that the column adsorption of V was a favorable chemical ion exchange process in monolayer. Several kinetic models were applied to analyze the adsorption characteristics. Analysis results of the Bohart-Adams model indicated that the adsorption process was dominated by external mass transfer in the initial stage. The Thomas model was appropriate to describe the column behavior, revealing that both external and internal diffusions were involved in the limiting steps.

Jan 1, 2014

By Fengming Li, Baocheng Song, Yuemin Zhao, Hailin Dong, Liping Peng, Chusheng Liu, Chenlong Duan

The large-scale vibrating screens with high processing capacity and efficiency are now in great demand in the mineral processing industry of China. However, as the equipment is always suffering from the strong external harmonic exciting force, the inertial force and the impact from the minerals, the fracture of the beam and the crack of the lateral plate are easy to occur, which has a negative effect on the reliability of the equipment itself and the industrial production. Considering the essential high reliability of the equipment, a new large-scale vibrating screen with duplex statically indeterminate mesh beam structure (VSDSIMBS) was developed. The natural characteristics, namely, the natural frequency (or the modal frequencies) and the natural mode, and the dynamic characteristics of the VSDSIMBS were obtained by the modal analysis and the harmonic response analysis. In addition, the dimensions and the constructions of the statically indeterminate plate and the mesh beam were chosen as the design parameters, to which the sensitivity of the whole mass, the maximum deformation and the maximum stress of the duplex statically indeterminate mesh beam structure (DSIMBS) were summarized for the optimization of the DSIMBS. Now the large-scale VSDSIMBS is being well used in China.

Jan 1, 2014

By J. T. Liu

Packing in a flotation column is one way to increase separation efficiency and effective descending flotation-column height. In this paper, the difference between filling packing and sieve packing is described, and the flaws of filling packing in flotation columns in industrial application are pointed out. A change of flotation process and its effect on flotation results are reported. Based on sieve-plate filling, a high-efficiency mixed packing mode consisting of screen-plate packing and honeycomb-tube packing has been proposed, with the packing mode optimized in the cyclonic static microbubble flotation column in the separation zone. In the mixed packing mode, the honeycomb tubes are used to reduce the vortex effect at the base of the column and weaken the radial dispersion of jetting bubbles, and the sieve plates are used to comminute bubbles in the separation zone, to lengthen the bubble migration path, and to stabilize the foam layer. The superiority of honeycomb-tube packing is analyzed using bubble-particle collision theory, and the dynamic equations of collision probability are derived. The role of mixed packing in guaranteeing mineral recovery is analyzed by the axial dispersion method, and a dimensionless axial dispersion model is derived. When a high-turbulence flow is maintained, a static separation environment is formed in which secondary mineral processing is rendered more effective. In this way, a nonlinear separation environment is formed in the flotation column. Finally, mixed packing was applied in an industrial test. A large vortex developed at the base of the column. It was observed that the bubbles in the radial flow were homogeneously dispersed, the residence time of the pulp was prolonged, and the froth layer became thick and stable. Based on the test data, it was found that the sieve packing has the potential to yield a product of approximately 25.83% copper concentration with 91.78% recovery from a feed concentration of approximately 0.727%. If mixed packing were used, the product concentration could be further increased to 27.60% from a feed of approximately 0.739% concentration with 93.38% recovery.

Jan 1, 2014

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By Ramon Augusto Moretti, Henrique da Rocha Severino, Renato Nascimento de Castro, Fernando Cesar Sousa

Rolling stand 12 (LTx) of long steel, installed in the company A, Piracicaba - SP unit, had presented high levels of vibration, which affected its internal components, such as: shaft, gears and bearings, generating downtime. To evaluate this equipment a study was proposed by the following engineering techniques: Conventional Vibration Analysis, Operational Deflection Shape (ODS) and numerical simulation by the Finite Element Method (FEM). In the Conventional Vibration Analysis, high levels of vibration were observed during manufacturing process, especially when the material reaches the equipment. Impacts generate high values in acceleration, on average 80 m/s² peak to peak. In the moment of impact, misalignment of internal components was observed by ODS. Field results were correlated to those obtained by the Finite Element Method, which allowed to calibrate FEM model. Thus, the most effective structural modification already numerically evaluated was implemented in the system. Afterwards, new measurements by vibration and ODS techniques were performed, and attenuation of vibrational levels and operational mode, which overloaded the internal components rolling stand, were verified.

Oct 1, 2019

By Jeremy Butkovich

Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.

By Greg Nutson, Jeremy Butkovich, Bill Perkins, Hollie Ellis, Paul Bott

"Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.INTRODUCTIONThe Evergreen Point Bridge conveys State Route (SR) 520 2.6 miles (4.2 kilometers [km]) from Seattle to Medina across Lake Washington. The bridge is located in a seismically active area, and the Washington State Department of Transportation (WSDOT) has determined that the western half of the 1960s-era bridge (the “west approach”) is vulnerable to earthquake damage. WSDOT has begun preliminary design to replace the west approach bridge.The west approach extends about 6,100 feet (1,900 meters [m]) east from Seattle’s Montlake neighborhood, over Union Bay and Foster Island, then into Lake Washington proper (Figure 1). Approximately 5,600 feet (1,700 m) of the replacement bridge would be constructed over water. Subsurface conditions along the bridge alignment consist of 5 to 80 feet (2 to 24 m) of very soft peat and clay, over very dense/hard sand and clay. Multiple pile supported columns support the existing bridge. The new bridge would be supported by 8- to 10- foot-diameter (2.4 to 3.0 m) drilled shafts that extend about 50 feet (15 m) into the underlying very dense/hard soil. To reduce seismic demands on the bridge superstructure, WSDOT has decided to incorporate a base-isolation system into the bridge design."

Jan 1, 2017

By Frank Rausche

Without doubt, driven piles are the most economical deep foundation element for a nearshore environment, providing for high bearing capacities and stiffness, quick installation times, assured quality by simple monitoring and inexpensive dynamic load testing during restrike testing. However, when the pile top elevation is several meters below water surface, questions often arise as to the most reliable and economical pile installation method. Frequently encountered, yet relatively expensive, solutions include driving inside a dewatered cofferdam, driving long piles that are later cut off below water surface, or using an underwater hammer. Arguably, the most economical solution is driving the piles with a follower or chaser. However, many foundation engineers shy away from this solution because of the uncertainty associated with the transfer of energy through the interface between follower and pile, the associated potential driveability problems and maybe the limited fatigue life of the follower. This paper will demonstrate how the driveability of a hammer-follower-pile-soil system should be analyzed prior to installation and how to model the pile-follower interface both for steel and concrete piles. As an example, results will be presented which were obtained for both steel pipe piles and precast concrete piles, driven by a single-acting diesel hammer through a steel follower for a pre-construction test pile program in Venice, Italy. While analysis of the steel pile-follower system was straightforward, for the concrete piles, the presence of a soft cushion material whose material properties changed continuously posed some difficulty. Pile Driving Analyzer® measurements and CAPWAP® analysis yielded not only realistic stresses and transferred energy values in the pile, but also reasonable model parameters for further use in a pure wave equation analysis. As a side note for clarity, the dynamic measurements and analysis results herein presented are based on the GRLWEAP and CAPWAP software. GRLWEAP is commonly used all around the world for the preparation of pile driving jobs. The program either yields a bearing graph that relates bearing capacity and pile stresses to blow count or set per blow or it predicts blow counts and pile stresses as a function of pile penetration. These results allow the contractor to estimate driving time and select an economical hammer and driving system for a safe and efficient installation. CAPWAP on the other hand is the analysis of choice once a pile has been installed and records of pile top force and velocity have been acquired during installation or during a restrike test. CAPWAP is a signal matching program which calculates for one particular impact (for example at the end of driving) the static and dynamic soil parameters. Its final results include the calculated resistance distribution, the complete stress history in the pile and also a simulated load set curve. The CAPWAP calculated dynamic soil parameters can also be used in a Refined GRLWEAP analysis to generate a calibrated bearing graph."

Jan 1, 2006