Search Documents

By Osvaldo Guilherme Comineli

While the hot cracking of Cu-containing steels is a serious and widely known problem for the industry, the literature reports that copper only slightly impairs the hot-ductility measured in laboratory. A distinction is drawn between hot ductility and hot shortness and the respective cracking operating mechanism involved at the respective range of temperature. The representability of the laboratory assessment of hot cracking of Cu-containing steels by hot tensile tests compared with actual results in industrial practice is discussed. The effectiveness of the variable affecting in each cracking mechanism and respective temperature range, focused in improving the hot cracking assessment of Cu-steels and the relative importance of oxidation will also be discussed. It is concluded that the hot tensile test in argon might be a good simulation if properly interpreted and that the role of oxidation is secondary in causing hot shortness. A schematic diagram for the hot tensile test is proposed.

Oct 30, 2017

By Donn A. Calder, Wayne C. Henderson

The Calmet Process for extraction and recovery of gold and silver from concentrates and high:grade ores has been a commercial reality for over two years. During that time period, almost seventy-five different concentrate (or ore) types have been processed in approximately 200 separate lots (a total of almost 2000 short tons). During commercial operation of the process at the plant in Fountain, Colorado, recovery of gold and silver into <lore' has averaged almost 93% for gold (range 81-98%) and over 90% for silver (range 76-97%) based on a fire assay target and calculated head values.

Jan 1, 1998

By G. Deschênes

Silver minerals are known to have slow leaching rates and low overall extraction and require a high concentration of cyanide and a long retention time to maximize leach extraction. Their response to cyanidation is considered mild to moderately refractory, largely due to complex mineralogical compositions. New research on improving the dissolution of silver minerals in cyanide was performed using high-purity minerals, as well as a high-grade ore sample from the Kupol property, owned 75% by Kinross Gold. The high-purity silver minerals studied in the leach investigations included acanthite, stephanite and pyrargyrite, which were also the predominant silver minerals in the Kupol ore sample. Dissolution of silver from acanthite produced only 37% extraction in 48 hours of leaching with 500 ppm NaCN. Analysis of the leached acanthite surface showed appreciable formation of polysulfide species, which can interfere with silver leaching. Adding lead nitrate into a pretreatment stage increased the acanthite silver extraction to 86.2%. No polysulfide species were formed with the addition of lead nitrate from the surface analysis. Cyanidation of stephanite and pyrargyrite produced very low dissolutions of silver, only 12.6% and 10.4%, respectively, in the absence of lead nitrate. Silver extraction from stephanite improved to 98% by adding lead nitrate directly to the leaching stage, whereas pyrargyrite required a pretreatment with lead nitrate to extract 83.2% Ag. With the addition of lead nitrate, the mineral surfaces had a PbO species and minor amounts of Pb(OH)2 and antimony was oxidized on the stephanite and pyrargyrite surfaces during leaching. There was a much greater concentration of Sb(V) on stephanite relative to pyrargyrite. Therefore, lead forms a redox couple on silver mineral grains and favors the oxidation of silver minerals. The high-grade Kupol sample assayed 22.6 g/t Au and 359.3 g/t Ag following treatment by gravity separation. Gold and silver extractions from the Kupol sample were 94.5% and 82.9%, respectively, using 500 ppm NaCN and 250 g/t lead nitrate. The findings to improve the extraction of silver from the ore sample with lead nitrate addition were congruent with those to improve the extraction of silver from the individual high purity minerals. Pretreatment did not, however, improve gold or silver extraction significantly with the ore sample.

Jan 1, 2011

By Don Ibana

The use of solvent extraction (SX) in process metallurgy is particularly attractive as it is applicable to a wide range of solute concentration and pH, and it allows complete separation of chemically similar metals such as nickel and cobalt and the rare earths among others. It is therefore applicable to the processing of low grade and complex ores, which is increasing and expanding owing to the diminishing reserves of quality ores, and this has driven the increasing and expanding use of SX.The current SX technology, however, has inherent limitations owing to the use of mechanical agitation as it induces high shear mixing. Excessive shear produces very fine droplets, and while this favours mass transfer, it also leads to sluggish phase separation. High shear mixing is also known to favour crud formation. All these factors as well as high power and reagents consumptions contribute to poor process efficiency. Electrostatic solvent extraction (ESX) is similar to conventional SX except that mechanical agitation is replaced with electrostatic agitation. In direct contrast to mechanical agitation, it allows the production of very small droplets that can be made to maintain intense motion, which favours mass transfer, without affecting the phase separation. In addition, as it uses an electrostatic field, the power consumption is minimal. Hence, it promises to be a superior alternative to conventional SX mixing although an application of the technique is yet to be achieved.Our work to develop an application of the technique in process metallurgy has now established that electrostatic field has no effect on either the stability of the reagents or the chemistry of the process. A volumetric flowrate that is comparable to that of a conventional sieve plate pulse column is achievable. We have also established that electrostatic fields can be made to yield much narrower droplet size distributions than those of mechanically agitated contactors, and they allow better control of droplet motions, which include oscillation and linear motion and hence, mass transfer. These are significant advancements toward our goal and shall be discussed in this presentation.

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country&apos;s total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment. &nbsp; Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry. &nbsp; Equipment suppliers now offer maintenance services, production guarantees and flexible financing. &nbsp;Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a &apos;package&apos; approach to customer service.

Jan 1, 1997

By Clayton V. Deutsch

Indicator Kriging (IK) is being commonly applied to mineral resource assessment problems. More recently, indicator simulation has also been used for sensitivity analysis and difficult change of support problems. The essential theory underlying indicator geostatistics has not changed since its introduction 10 years ago; however, the last decade has produced many important developments in its implementation. The objective of this paper is to consider some of the more important implementation details. Examples from the Porgera gold deposit in Papua New Guinea are used to illustrate the steps in an indicator geostatistical study and the importance of various implementation decisions. Specifically, in many precious metals deposits the continuity of the grades is typically quite anisotropic. This anisotropy varies in both magnitude and direction throughout the deposit. Building a model of this anisotropy can considerably improve the local kriged or simulated points. One approach to build this model is presented. In addition, there is typically more than one mineralization style and geological rock type; the spatial character of the mineralization can be quite different within each geological rock type. The rational treatment of anisotropy and geological subdivisions is common to all mineral resource assessment procedures; the importance of this qualitative geological information is not diminished with more sophisticated techniques such as indicator kriging. This paper presents an overdue comprehensive look at the practical aspects of indicator methodology. Many of the techniques and procedures documented in this paper have been developed during the course of detailed mine feasibility studies.

Jan 1, 1992

By Dever Ashmead

ANTHRACITE was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they were mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracite. MINING METHODS AND THEIR RELATION TO PREPARATION In the beginning f the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal.

Jan 9, 1921

By M M. Hilden, M S. Powell, B Foggiatto

In an environment of decreasing ore grade, increasing costs and uncertainty with respect to commodity prices, the industry could benefit from evaluating alternative technologies and innovative circuit configurations. The flexible circuit approach suggests that the design of grinding circuits can be adapted to changes in feed properties and economic conditions. Advances in modelling and simulation are enabling metallurgists to predict the performance of more complex circuit configurations with increased confidence. Ore variability information and processing costs may be used as modelling inputs to determine the optimum processing conditions at a given time. A case study has been completed demonstrating the value of combining a flexible circuit with a model-based optimisation of the process. Ore properties and equipment performance data obtained in operating plants have been used to model and simulate flexible circuit configurations.This paper explores strategies to introduce flexibility to existing circuit configurations when processing ores with high variability. Multicomponent models incorporated in the model developers’ kit (MDK) allow the simulation of more complex and flexible circuits. This capability enables demonstration of the potential to enhance metal production through adapting processing routes according to the ore type being processed. The simulation of different flow sheet configurations allowed the definition of the best option for maintaining the metal production when treating lower grade ores, highlighting the advantages of flexible circuit configurations compared with a one-process-fits-all approach.CITATION:Foggiatto, B, Hilden, M M and Powell, M S, 2014. Advances in the simulation of flexible circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 391–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004

By J. S. Bays

Industries are challenged to meet increasingly stringent regulations for selenium and metals. Cost-effective treatment is required to minimize the economic impact of environmental compliance. Low-cost biological treatment of selenium can be achieved passively using biochemical reactor cells composed of natural organic media components such as wood chips, sawdust, hay, composted manure, and peat. The reactor cells create an anaerobic microenvironment for biological reduction and sequestration of selenium and other metals. Biochemical reactors can be combined with constructed wetlands for flow equalization and to remove the organic byproducts in reactor cell outflow. Passive treatment reduces capital cost and operational effort compared to more expensive and complex physical and chemical treatment. Recent pilot and full-scale projects by mining companies and by the US Bureau of Reclamation demonstrate that passive treatment can achieve compliance with selenium concentrations over a range of flows and environmental conditions. Case histories of passive selenium treatment systems and their key findings are provided, and prospects for future applications are summarized.

Feb 27, 2013

"Previous studies on the effect of polytetrafluoroethylene addition during chalcopyrite leaching under conditions similar to those of the CESL process have reportedly resulted in complete leaching of the copper without the need for grinding of the flotation concentrate. However, these studies employed a pulp density of only 1% and finely sized PTFE particle that required the use of high impeller rotation rates that are not sustainable at an industrial scale. This paper explores the performance of 1/8” diameter balls of PTFE, that readily sink in the leach solution, on leaching performance at impeller rotation rates and ore pulp densities more typical of industrial practice. Possible routes for separation of the PTFE from the leach residues and their regeneration for recycling back to the leaching stage are also discussed.INTRODUCTIONChalcopyrite, CuFeS2, is the most important primary sulfide source of copper. While pyrometallurgical smelting of chalcopyrite remains the only widely accepted route for treating chalcopyrite concentrates, several medium temperature pressure oxidation processes are claimed to be economically feasible (Muir & McDonald, 2007). Among these, the CESL process has been extensively piloted and demonstrated at the prototype scale. The overall process chemistry of the CESL process may be summarized as follows (Marsden & Wilmot, 2007):4CuFeS2 + 5O2 + 4H2SO4 ? 4Cu2+ + 4SO4 2- + 2Fe2O3 + 8S0 + 4H2O (1)4CuFeS2 + 17O2 + 2H2SO4 ? 4Cu2+ + 10SO4 2- + 4Fe3+ + 2H2O (2)Though copper extractions of over 95 % are achieved, the CESL process requires extra grinding of the concentrate (Muir & McDonald, 2007). This is because leaching is conducted at temperatures around 150 °C, where the elemental sulfur produced is molten and grows thicker on the mineral’s surfaces as oxidation progresses, creating an increasingly large barrier for mass transport. In addition, the sulfur is sticky and tends to cause the mineral particles to agglomerate, effectively halting further oxidation of the particles that end up embedded within the agglomerates. Consumable surfactants, such as ligin sulfonate, have been shown to be effective at avoiding agglomeration, but they are not effective at removing sulfur from the minerals. Hence, their use does not obviate the need for fine grinding."

Jan 1, 2012

By James F. Archibald

In historic mining practice, typical thin liner support systems have been considered to comprise non-reinforced or mesh-reinforced shocrete linings. In the early 1990?s, development of alternate forms of liner systems was initiated in Canada which is now undergoing significant international growth in countries which sustain major mining activity. Now internationally designated as thin, spray-on liner systems, a wide spectrum of liner materials, ranging from liquid/liquid to liquid/solid component combinations, has become commercially available. This innovative family of products is characteristically identified as being rapidly deployable, capable of creating ultra-fast setting coverage over rock surfaces, and able to develop tenacious adhesion and pull strength capacities for resisting rock falls and movements. This paper presents a summary of current liner developments and use in principal mining districts world wide. Additionally, a database of material properties for principal product types used in mining and a review of common quality control testing procedures under development are provided. Such information is based upon recent Canadian and international efforts being taken to assess and develop user standards for the implementation of thin, spray-on liners as rock support in mines. This work is intended to continue for a period of years, with the eventual goal being to establish support and installation guidelines for mines based on quantifiable laboratory and field research.

May 1, 2002

Advances in Thickener Feedwell Design via Computational Fluid Dynamics Modelling

Sep 13, 2010

By A R. Heath, I Arbuthnot

Feed slurries are typically flocculated in a thickenerÆs feedwell to increase the settling rate, underflow density and overflow clarity. High molecular weight polymeric flocculants are normally used, but present a number of challenges in terms of make up, dilution, delivery and mixing with the feed slurry.Various aspects of the flocculant dilution and delivery system have been studied with a combination of flow visualisation and computational fluid dynamics (CFD). An open topped flocculant dilution/mixing box has been developed to replace a conventional flocculant manifold, with improvements to the mixing, fault diagnosis and ease of determining the flow split to the various dosing points. The addition points to the feedwell have also been studied, both in terms of where the flocculant is added, and how. While conventional multi-hole spargers are effective in dispersing flocculant, they are prone to blocking and have been replaced by open-ended pipes. The required dispersion is provided by an efficient mixing element placed in the dilution port. Adding the flocculant into the feedwell dilution stream prior to mixing with the slurry also provides super-dilution of the flocculant that can further improve the flocculation process and reduce flocculant consumption.CITATION:Heath, A R and Arbuthnot, I, 2013. Advances in thickener flocculant delivery, in Proceedings MetPlant 2013 , pp 86-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Thomas E. Newman

This paper is a case study using new laser-terrain-mapping technology by EagleScan, Inc., for creating topographic maps. Holnam, Inc., has used this technology to create maps and volumetric calculations of several mines in the United States. The information is superior to conventional methods through accuracy, manpower, time, and cost. Holnam, Inc., was the first cement manufacturer to use the Digital Airborne Topographic Imaging System (DATIS?). The technology uses the DATIS? to produce high-resolution terrain maps and volumetric assessments of any area. DATIS? is a mapping instrument that integrates (1) a Light Detection and Ranging (LIDAR) instrument to measure terrain elevation using laser light, (2) a large-format digital camera, (3) a relative position Global Positioning System (GPS) to measure aircraft position, and (4) an Inertial Measurement Unit (IMU) to measure aircraft attitude. The DATIS? can measure up to 220,000 elevation samples per mil. The system continually collects data on the aircraft&apos;s position and measures the time for each laser pulse transmission to return from the ground, giving each sample a GPS reference. The system can operate at night, in overcast sky, and during high-wind conditions and can measure terrain below vegetation cover, unlike standard aerial photography used for traditional surveying and mapping. Surveyed ground-control panels are no longer necessary with this new technology, and only one ground GPS base station located within 60 mi from the aircraft position is required. A computer elevation-point data file is created with the x, y, z coordinates of each laser elevation sample. With this file, CAD engineering programs can create topographic maps that rival products using conventional aerial mapping techniques. Volumetric measurements of stockpiles and pits are also available due to the high density of points collected from an area. This new technology radically changes the turnaround time for map users, giving a product in the format used by today&apos;s cartographers. The time line from flight to maps is measured in days instead of weeks.

Jan 1, 1999

By Steve Kral

"Repairing and replacing the nation’s aging and crumbling infrastructure has become a major issue with the American public. It is no secret that the upkeep of roads, tunnels, bridges, and water and waste water facilities has been neglected for decades. Cities, states and towns across the United States are now grappling with these issues, ones that will take decades and billions of dollars to fix.Because of this infrastructure issue, the North American tunneling industry is flourishing. Cities across the country are looking to go underground to alleviate traffic issues, transporting water and waste water to more people in more efficient ways.In October, the seventh annual Cutting Edge conference was held in Atlanta, GA. Put on by the Underground Construction Association of SME and Britain’s Tunnelling Journal, about 175 tunneling and underground construction professionals from around the world attended. Attendees included owners, designers and contractors. An accompanying exhibit included 28 companies.The theme of the two-day conference was Advances in Tunneling Technology. Speakers examined the latest advances in tunneling technology, its methodology and how these advances can be harnessed to assist upcoming major tunneling projects. The conference featured a tailored, high-end, single-track program of subject-specific presentations that focused on innovation and practical experience. Two in-depth panel discussions at the end of each day were also included.Patricia Mulroy was a keynote speaker on Monday. She is senior fellow for climate adaptation and environmental policy at The Brookings Institution. Like many others, Mulroy believes the U.S. infrastructure in in a state of disrepair. But, she said, no one wants to talk about it. “We need to have a conversation about infrastructure. We cannot be afraid to talk about building it and the cost.” For this to happen, though, the nation needs leadership."

Dec 1, 2018

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

China has large amounts of iron ore reserves, but iron ore in China, with low-grade, small disseminated particles and many other associated minerals, is difficult to dress. In recent years, with the fast development of China&apos;s steel industry, the demand for iron ore has increased markedly. The new technologies in iron ore dressing in China are very effective in processing haematite and other difficult to dress iron ores. The iron ore grade and recovery rate has been improved. This result alleviates the difficulty in iron ore supply in China.

Jan 1, 2007

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009