Search Documents

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton

Five years ago, VALE Base Metals (then INCO), approached Pelton's group at McMaster and described a challenging mineral separations problem. The McMaster group has a strong track record in colloids, polymers, and chemical additives for papermaking; however, they had no experience in mineral processing. They proposed employing hydrophobic nanoparticles to replace conventional low molecular weight, water-soluble flotation collectors. Over the last five years, Vale, together with the Ontario Government (OCE) have funded two graduate students at McMaster who have worked closely with flotation experts at Vale. Experiments involving both very clean model mineral suspensions at McMaster and complex ores at Vale, have shown that hydrophobic nanoparticles do indeed function as collectors. Key nanoparticle properties and mechanisms have been identified and the technology has been protected in patent applications. Efforts to commercialize the technology are on-going. We believe that this project is a good case study demonstrating the advantages of industry-university collaboration and the use of outside experts, who may come up with novel solutions to complex problems.

Jan 1, 2011

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton

"Hydrophobic polystyrene nanoparticle suspensions were evaluated as potential flotation collectors for pentlandite. Experiments involving both clean model mineral suspensions and complex ultramafic nickel ores confirmed that conventional water-soluble molecular flotation collectors such as xanthate could be partially or completely replaced by hydrophobic nanoparticle flotation collectors. The ability of nanoparticles to induce flotation was demonstrated by floating hydrophilic, negatively charged glass beads with cationic polystyrene nanoparticle collectors. Electrostatic attraction promoted the spontaneous deposition of the nanoparticles on the glass surfaces raising the effective contact angle sufficiently high to promote the adhesion of beads to air bubbles. As little as 10% coverage of the bead surfaces with our most effective nanoparticles could promote high flotation efficiencies, whereas conventional small molecular flotation collector requires ~ 20% or higher coverage for a good recovery. Surface functionalized nanoparticles enhanced the ability for nanoparticle collectors to selectively deposit onto surfaces of the desired mineral particles in the presence of gangue. For example, poly (styrene-co-vinylimidazole) nanoparticles were designed to selectively deposit onto nickel mineral (pentlandite) in the presence of Mg/Si slime. Flotation tests of ultramafic nickel ores at Vale with these nanoparticle collectors have shown improvements in both pentlandite recovery and selectivity. On-going work includes attempts to identify specific applications where nanoparticle flotation collectors might be cost effective.INTRODUCTION Most mineral processing operations include multiple stages of froth flotation to concentrate and isolate the desired product. Before flotation, chemical collectors are routinely added to ground ore slurries, selectively binding to mineral-rich particles, increasing their hydrophobicity thus promoting selective flotation. (Fuerstenau, Jameson, & Yoon, 2007) Conventional collectors are surfactants with a short hydrocarbon tail and a head group, such as xanthate. A typical conventional collector is potassium amyl xanthate (PAX), which is a small molecule with an extended molecular length of about 1 nm. Critical characteristics of a good collector include the ability to selectively adsorb onto desired mineral surfaces and to lower the water/mineral surface energy. Despite the extensive role of flotation in mineral processing, some ores are difficult to process by flotation. For example, ultramafic nickel sulfide ore containing both valuable pentlandite and large quantities of unwanted Mg/Si slime [primarily serpentine, (MgFe)3Si2O5(OH)4] responds poorly to flotation. (Mani, Xu, Quinn, & Stratton-Crawley, 1997) Fibrous hydrophilic Mg/Si slime usually masks the surface of pentlandite (known as “slime coating”) due to electrostatic interaction (Edwards, Kipkie, & Agar, 1980) and dramatically depresses pentlandite flotation. Consequently, new approaches are required for processing these difficult ores."

Jan 1, 2012

By R. Pelton, Z. Dai, S. Yang

ABSTRACT Hydrophobic polystyrene nanoparticles were evaluated as potential flotation collectors for pentlandite. The flotation of hydrophilic glass beads demonstrated the nanoparticles’ ability to induce flotation. Deposition of nanoparticles on glass surfaces increased the contact angle and enhanced adhesion of the beads to air bubbles. High flotation recoveries were achieved when 5–10% of the bead surfaces were covered with nanoparticles. Surface functionalization—the addition of vinylimidazole to polystyrene nanoparticle surfaces—caused the nanoparticles to selectively deposit onto pentlandite surfaces in the presence of Mg-Si slimes. Ongoing work includes attempts to identify specific applications where nanoparticle collectors might be cost effective. _ KEYWORDS Flotation, Nanoparticle collector, Coverage

Jan 1, 2014

A search for the keyword nano reveals that it has not made a significant entry into the mineral processing research literature. In contrast, the terms micelle, colloid, interface, and monolayer are well established there. By considering nanoscience as colloid and interface science at the nanoscale, it is claimed that several previous and current investigations in the broad field of mineral processing fall under the umbrella of nanoscience. Several examples from hydrometallurgical processing systems (invisible gold and activated carbon in gold extraction; monolayers, reverse micelles, and microemulsions in solvent extraction; nanobiofilms and nanoparticles in biohydrometallurgy) are highlighted in support of this view.

Sep 13, 2010

By Igor Zh. Bunin

A model for developing electric discharges between sulfide mineral (pyrite) particles under high-voltage nanosecond pulses in a liquid medium (water) is considered. A possibility of electrical breakdowns of liquid gaps between particles under nanosecond pulses is shown. This probability and the energy released in discharge channels depend strongly on the sulfide conductivity.

Jan 1, 2010

By J. H. Baek, D. W. Lee, B. K. Kim

Nanostructured Cu-Al203 composite powders were synthesized by thermochemical process for an electrode application. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from copper and aluminum nitrates, 2) heat treatments to evaporate volatile components in the precursor powder and synthesis of nanostructured CuO+Al2O3, and 3) CuO reduction by hydrogen into Cu. The suggested procedures stimulated the formation of the gamma-Al2O3. The mean particle size of the final composite powders was 20nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/Al2O3 composite by the conventional internal oxidation process.

Jan 1, 2004

By Chuan-Jian Zhong

Gold-based nanoparticles in the size range of a few nm have attracted increasing interests in catalysis, sensors and biomedical applications. The study of the unique catalytic properties of nanosized gold was inspired by the pioneering work of Haruta on the nanogold-catalyzed CO oxidation (1-4). There have been a number of excellent reports discussing both fundamental and application aspects of gold nanoparticles in catalysis (3-8). Our work reported herein is aimed at investigating the preparation and application of gold and its alloy nanoparticles for potential applications in fuel cell catalysis. Fuel cells operating by electrochemical oxidation of hydrogen or methanol fuels at the anode and reduction of oxygen at the cathode are attractive power sources due to their high conversion efficiencies, low pollution, lightweight and high power density. While methanol offers the advantage of easy storage and transportation in comparison with hydrogen fuel cell, its energy density (~2000 Wh/kg) and operating cell voltage (0.4 V) are much lower than the theoretical energy density (~6000 Wh/kg) and the thermodynamic potential (~1.2 V). The poor activity of the anode catalysts and inefficient activity or issue related to "methanol cross-over" at the cathode electrode are associated with the loss of about one-third of the available energy at the cathode and the other one-third at the anode. Extensive studies have been focused on Pt-group metals (Pt+Pd+Rh+Ru+Ir (PGM)) for both anode and cathode catalysts. A major problem is the poisoning of Pt by COlike intermediate species (9,10). Recently, oxide-supported gold nanoparticles in the <10 nm size range have emerged as one of the best catalysts for CO oxidation (1-3,11), and for water gas shift reaction in reforming stage using 5 nm Au on Fe2O3 (6). Gold and its alloy with other metals in the nanosize range present new alternatives (2,12). Whether the unique properties of gold nanoparticles can be exploited for addressing these problems is a focus area of our work. The ability to harness the large surface area-to-volume ratios and the unique surface sites of nanoparticles in <10 nm size range, especially in heterogeneous catalysis, constitutes a major driving force in fundamental research and practical applications of nanoparticle catalysts. It is this size range over which the metal particles undergo a transition from atomic to metallic properties. The understanding of factors controlling the morphological and surface reconstitution associated with such a size range is of fundamental importance to the ultimate exploration of nanostructured catalysts. We have been investigating the interfacial structures and properties of core-shell types of nanoparticles consisting of gold or alloy nanocrystal cores and organic monolayer shells that were prepared by twophase synthesis (13) and processing (14) protocols. Important attributes of such nanoparticles include controllable size monodispersity, processibility, and stability towards size- and composition-tunable catalysis (15-21). Some of these attributes were studied for understanding their electrocatalytic properties in the oxidation of methanol and reduction of oxygen, which are of fundamental interest to fuel cell technology.

Oct 1, 2003

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994

By T. A. George, David J. Sellmyer

"The concept of achieving a useful high-energy-product magnet through appropriate nanostructuring of known hard and soft phases has been tantalizing researchers since the idea was first proposed. The fabrication of exchange-coupled nanocomposite magnets faces several challenges including aligning the easy anisotropy axes of the hard-phase grains. Here we investigate experimentally two-phase nanostructures of hard Lio-ordered FePt and soft iron-rich/cc Fe(Pt). The Fe-Pt thin films were produced by epitaxial cosputtering onto MgO (001) single-crystal substrates which lead to strong (001) texturing. The measured hysteresis loops indicate nearly ideal exchange coupling. Excellent magnetic properties are obtained, with largest values of coercivity (51 kOe), saturation magnetization (1287 emu/ cm3, J, = 16.2 kG), and nominal maximum energy product (58 MGOe).1. IntroductionA key figure of merit for permanent magnets is the maximum energy product (BH)rrw.x. The achievable maximum energy product is determined by a magnet's saturation magnetization M, and its magnetic anisotropy. For example, it is well known that (BH)rrw.x :S 4n2M,2• In the past, record energy products have been the result of discovering new compounds with high values of magnetization and anisotropy. However, finding new compounds with better magnetic properties than the current record-holding magnet Nd2Fe14B has proven to be difficult. A different approach is to exploit the exchange coupling mechanism between known hard and soft magnetic phases to enhance the maximum energy product [1-5]. In such a composite system, high coercivity is achieved due to the anisotropy of the hard phase as well as a nanostructure which prohibits large-scale domain wall reversal mechanisms. Magnetization is enhanced by the soft phase and loop squareness results from texturing of the hard phase easy-axis as well as complete exchange coupling between the coexisting hard and soft grains."

Jan 1, 2012

By Jim Huerta

Diesel fuel usage in the mining industry continues to escalate. This is because approximately 60 percent of all mined materials are surface extracted by large equipment using diesel fuel, which continues to increase in cost per gallon. For example, coal mining uses large equipment such as wheel loaders, wheel dozers, draglines and [ ] dredgers. In one year, three of the largest U.S. coal mining operations consumed approximately 567 million to 852 million L (150 million to 225 million gal) of diesel. At an approximate cost average of $3.25/gal the expenditure on diesel is $487 million to $731 million per year. So, are there any solutions that could reduce this cost burden? Yes, there are. Coal mining companies can extract less ore; use more efficient extracting equipment that consumes less fuel; wait for a significant reduction in the cost of fuel; or find and use technology that would create efficiencies that would lower the cost. Nanotechnology is one such technology that might provide the means to create the efficiencies that will significantly lower diesel fuel costs.

Jan 1, 2011

By E. Oshima

In May 1991, a New Mitsubishi Continuous Copper Smelter Line started operation at Naoshima. Recently, it has been continuing steady operation and one and a half year campaign life has been achieved. In 1996, new records of on line time, the amount of copper concentrate treated and copper anode production were achieved. 1t proves the superiority of the process with respect to pollution control, energy efficiency, flexibility and easiness of the operation and over all economy including off gas handling cost. Furthermore, .plans are underway to prolong the campaign life for two years and to improve the process efficiency. This paper describes recent operation, improvements, and a future capability study.

Jan 1, 1998

By Paolo Prevedini, Antonello de Risi

"The city of Naples has one of the most ancient traditions of tunneling in the world, since Roman age until today. This was due to the softness of volcanic rock covering most of the city surface, this determined in centuries the excavation of many connected cavities, today still accessible. The building of metro lines promoted industrial tunneling construction: TBM, Raise Boring Machine, Vertical Shaft Machine and freezing technologies played a decisive role facing water pressure near the sea. MNspa is an advanced constructor with two lines built in parallel, mainly underwater. The planning of this infrastructure has been upgraded with the projects of international architects from all Europe, with installation of art masterpieces in station spaces while archeological excavations revealed artifacts since Paleolithic. The city expects to give a new image of the urban landscapes within the completion of all stations and consequent rehabilitation of interiors and external city spaces. A case study of Municipio square station, is chosen to explain the relevance of archaeological research in improving and developing the projects of Line 1 stations. In these pages, it will be explained how the engineering process required to deal with Art, Architecture and Archaeology to finally realize an extended urban renovation of Naples. 1 CITYSCAPE 1.1 Introducing the geological history of Naples In the evolution of the city, capital of the Magna Graecia and of consequent kingdoms, a new layer of buildings was added over the foundations of demolished walls of the precedent domination period: from the top of the Bourbons layer (the most common scenery of the city since 1734) to the Aragonese layer found just underneath it; then below stands the Angiovin city, which in turn is built above the Swabian traces; underneath the ancient traces of the Byzantine age are found just above the extended Latin age layer. The most ancient settlement, known as Parthenope, dates back to 1500 b.C. It sits below the Greeks remains of the city of Palepolis, which had been rebuilt under the name of Neapolis by Romans."

Jan 1, 2016

By S Hall

Mining schools around the world, many unfortunately now closed, were often established to teach the techniques of narrow vein mining and associated processing to students studying part-time while working in the industry. This arrangement ensured graduates (or æassociatesÆ) had a mix of skills and knowledge invaluable to the industry.It is argued that there is still a need to educate students in these narrow vein techniques and that there will be a growing demand for such graduates with a high level appreciation of this type of mining. There is also a need for innovation in narrow vein mining and processing to develop specific technologies and allow the use of techniques applied in æbulk miningÆ to achieve improvements in productivity, safety and economic performance.This paper aims to review the situation with regard to education and innovation in narrow vein mining.CITATION:Hall, S, 2012. Narrow vein education - back to the future?, in Proceedings Narrow Vein Mining 2012 , pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

Due to deposit shape and dimension, narrow vein makes reserve modeling, geological control, stope design, drill and blasting more challenging. It needs high standard quality control as errors can be created easily, which could cause significant amount of ore loss or dilution. From channel sampling, survey control, reserve modeling, drill hole design, blasting, communication with underground drillers to backfill, this paper illustrated every step and its quality control of a long hole stope mining. Compared to other narrow vein mining methods (cut and fill and shrinkage), long hole stoping means higher production, less labor, and significantly lower cost when deposit characteristics allowed.

Jan 1, 2012

By John G. Henning

The Hoyle Pond underground mine is located in the Porcupine Gold Camp, 18 km east of downtown Timmins. Since the initiation of production in 1985, the operation has produced in excess of 1.9 million ounces of gold at a grade of 15 grams per tonne. Currently, Hoyle Pond ranks 8th in total ounce production for all past and present producing mines in the camp, with the highest head grade of any of the significant past, or present producing mines in Timmins. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. Using illustrative examples, this paper provides an overview of factors, such as geologic setting, rock mechanics challenges and mine infrastructure, which influence mine design at Hoyle Pond.

Oct 1, 2004

Citigold Corporation operates the Warrior gold mine at Charters Towers, northern Queensland, mining narrow quartz veins (0.1 to 2 m wide) in granodiorite by long hole open stoping on levels 15 m apart. Access is by decline and cross-cuts with on-ore development drives. The mineralisation comprises Palaeozoic mesothermal quartz veins containing gold, pyrite, sphalerite and galena, hosted by the Ordovician age Towers Hill Granite. The gold grain size is variable from 1 to 500 ¦m with 1 m face samples up to 800 ppm Au, and average run-of-mine grades of 10 to 14 ppm. Despite the spectacular gold tenor, little visible gold is present. Gold grades are highly variable presenting challenges in ore reserve estimation. Tonnages are discounted by 70 per cent to allow for the low payabilities (30 to 50 per cent) of the veins. Estimation techniques allow high confidence in overall global grade estimates but poor reliability on a local scale (25 m). Kriging ranges as low as 5 - 8 m means that obtaining a Proved Ore Reserve by diamond drilling is not economically feasible, and broad-scale mine planning decisions are made at the Inferred Mineral Resource stage and mine design work at the Probable Ore Reserve stage. Proved Ore Reserves can only be estimated after underground development has proceeded through the mineralised body with levels at 15 m vertical spacing sampled at 2 - 3 m intervals along the level. However, reconciliations between actual gold produced and earlier resource estimates produce workable results. A further three mines are scheduled to be developed underneath the city of Charters Towers.

Jan 1, 2008

By R F. G Phelps, C J. S Sangster, G S. C

Narrow vein metalliferous mining in the UK has a long history, but there are only two small gold operations at present (Clogau and Gwynfynydd). Four further gold properties are at various stages of evaluation (Calliachar, Cononish, Curraghinalt and Maestryfer). The South Crofty tin mine closed earlier in the year. Narrow veins are exploited underground and are challenging to evaluate because of their geologically variable nature. They are generally less than 3 m wide, discordant, of variable dip (

Jan 1, 1998

By Stephen G. Downs

PCF?, or Penetrating Cone Fracture, is a propellant-based technique for rock excavation, which has significant potential for the mechanization of narrow-vein mining. The technique is currently being developed for use in the narrow-vein flat-dipping gold and platinum deposits in South Africa in conjunction with major mining companies. The technique is also applicable to steeply dipping vein deposits, such as those found in North America, Australia and elsewhere. The implementation of PCF? in South Africa to date is reviewed and plans for the introduction of PCF? excavation in other areas are highlighted.

Oct 1, 2001

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009