Search Documents

HISTORY OF PROCESS DEVELOPMENT The manufacture of coke from coal commenced at the beginning of the 17th century by heaping coal into circular mounds in the open, covering with earth, clay or ash and slowly burning the coal in the mounds to produce a heap of coke. Naturally the process was slow in production rate with low coke recovery due to the loss of that part of the coal which was completely burnt to ash. As a natural consequence of this initial carbonisation method, a coke oven design was developed so that the coking chamber, which was constructed of brick, was circular in plan, cylindrical in section with a dome shaped roof - similar in shape to the original coal mounds. As the shape of the chamber was similar to the old dome shaped beehive, the ovens were called beehive ovens. The ovens were built in long single or double rows with retaining walls between each oven and as such were known as a battery of beehive coke ovens. In these early beehive ovens, coal was charged from hand wheeled tubs into a hole into the top of each oven, hand- levelled with a rake and the oven side opening sealed with bricks and clay except for some small holes in the opening to admit limited quantity of air for combustion. Coking commenced by the heat retained in the brickwork from the previous charge. The gases evolved from the coal, together with the admitted air, were partially burnt inside the oven to supply the heat for carbonisation and the surplus gases were burnt to waste at the top charging hole. The heat from this gaseous combustion inside the oven together with the reflected heat from the brickwork of the arched roof of the oven allowed carbonisation of the coal charge to proceed from its surface slowly downwards to the floor of the oven. At the end of the coking cycle (usually 4 or 5 days) when there was no more evolution of gases, as indicated by diminishing gas flame and a drop in oven temperature, the brickwork of the oven opening was removed. The coke was then quenched by inserting a pipe with spray holes to spray water over the coke charge in the oven after which the coke was raked from the oven. The work of charging and levelling the coal, bricking and removal of oven opening, quenching and raking out the coke all required manual labour. As these ovens only carbonised a 5 to 7 ton charge of coal per cycle of 4 to 5 days, to produce 3 to 41/2 ton of marketable coke, the labour required per ton of coke was high.

Jan 1, 1975

By Nelson Hogg

"THE NOR-ACME gold mine is located close to the north shore of Snow Lake, at 54°53' north latitude and 100°03' west longitude. It is about 75 air miles east of Flin Flon, and 36 miles by road from Wekusko at Mile 81 from The Pas on the Hudson Bay Railway.The claims which contain the Nor-Acme orebodies were staked in 1927 by C. R. Parres, who, with his sons, held the ground until 1938 when Nor-Acme Mines Limited was incorporated. In 194 l, on the recommendation of F. Ebbutt (1), this property was optioned by the Howe Sound Exploration Company, Ltd. A program of 50,000 feet of diamond drilling resulted in the outlining of two orebodies containing an estimated 5,000,000 tons with an average grade of 0.15 ounces per ton to a depth of 1,000 feet.A period of inactivity during the war years was followed by the construction of a mining plant capable of treating 2,000 tons of ore per day. Milling started in March 1949, and to the end of 1954 has resulted in the production of 383,793 ounces of gold and 32,906 ounces of silver from 3,331,403 tons of ore.General GeologyThe general geology of the Snow Lake area is described by J. M. Harrison (2), and will not be discussed here except insofar as it affects the Nor-Acme orebodies. The orebodies occur in rocks of Precambrian age that have been classified by Harrison as the Snow group, comprising meta-morphosed sediments interbedded with acid and basic volcanic rocks. The volcanic rocks include pyroclastic types which are unique in the region, a fact which led to their classification in the Snow group rather than the more widespread Missi group that generally occupies the same stratigraphic position above the Amisk group (Figure 1)."

Jan 1, 1949

By J. M. Harrison

"The Nor-Acme gold mine is near the shore of Snow lake, northern Manitoba, about 75 miles east of Flin Flon. The claims that form the nucleus of the present property were staked in 1927 by C. R. Parres, but it was not until 1941 that diamond drilling disclosed the potentialities of the deposit. In that year a large-scale drilling programme was begun under the direction of F. Ebbutt, of the Howe Sound Exploration and Development Company. Two orebodies were outlined containing about 5,000,000 tons of ore assaying $5.25 in gold per ton. In August, 1945, construction of the mining plant was begun.All information and interpretations contained in the following brief description of the deposit were obtained from surface mapping.GEOLOGYThe ore lies at the contact between a coarse, basic, pyroclastic rock, which is the hanging-wall, and grey, acidic lavas and sediments, which form the footwall. These rocks are cut by irregular basic intrusions that vary in composition from diorite to hornblendite, and by small acidic dykes . Tourmaline is locally common in the hanging-wall rock near the ore.The ore occurs in brecciated, silicified, and ·slightly carbonatized rock. Arsenopyrite is the main sulphide and the gold is associated with it. Pyrrhotite is locally abundant and minor pyrite, chalcopyrite, sphalerite, galena, and cubanite have been noted. Two orebodies are known, the Dick and the Toots. The Toots, which is much the smaller of the two, is about 1,000 feet west of the Dick."

Jan 1, 1954

By David Scott, Denis V. Lachance, Daniel Marcotie

"LocationThe Heath Steele mine is located 50 km northwest of Miramichi, New Brunswick.Brief DescriptionHeath Steele is a 2700 t/d, copper-lead-zinc operation which employs conventional crushing, grinding, and differential flotation.HistoryThe Heath Steele mine is located in northeastern New Brunswick approximately 50 km northwest of the city of Miramichi and 65 km southwest of Bathurst. The massive sulphides containing ore values in zinc, lead, copper and silver were discovered in 1953 as a result of a joint venture between the American Metal Company and the International Nickel Company of Canada. The discovery was named after Mr. Heath Steele, manager of exploration for Amco at the time of the discovery.Mill production began in February 1957; however, the mine was forced to shutdown in 1958 due to depressed metal prices and metallurgical problems. It was re-opened in 1962 and milling operations resumed at 725 t/d until 1968 when the milling capacity was boosted to 1450 t/d and then to 2700 t/d in 1969.OreThe main ore zones are massive sulphides with very fine mineral grain. The chalcopyrite, galena and marmatitesphalerite occurrences are finely disseminated.Liberation is accomplished by grinding to 68% to 72% <400 mesh. Average mill feed assays are 0.8% to 1.2% copper, 1.8% to 2.5% lead, and 5.5% to 6.5% zinc, with 60 to 75 g/t silver."

Jan 1, 2000

Concentrator Improvements -1990-1995Back to Basics ?pilot plant versus plant opportunities identified ?understand process fundamentals & baseline -1996-2000Point ?C?Projects ?strategy to improve global competitiveness ?structure implemented to generate & drive ideas ?capital investment for life of mine asset renewal - 2001-200?Six Sigma Methodologies ?emphasis on data, measurements & analyses ?dedicated, highly trained personnel on projects 1990-1995 Improvement Phase??Philosophy??back to basics?approach?understand what each piece equipment needed to do?understand reagents, control variables?confirm operating strategies ??probe, stabilize, institutionalize??test theories, confirm with lab and plant trials?process stability (equipment reliability, controls)?enhanced operator guidelines, operator training?focus on continuous improvement?optimize existing equipment capability?stop looking for ?magic?solutions 1990-1995 Improvement Phase??Technical?finer grind, same equipment?optimize media size/shape to grinding application?balanced available ball mill power to applications?lowered cyclone feed densities where possible?improved selectivity, same equipment?balanced available cells to applications?streamlined process (eliminate process steps)?added cleaning stages where required?understanding pulp/mineral surface chemistry?lowered flotation pulp densities 1990-1995 Improvement Phase??Effort?numerous studies to understand process?liberation and mineralogical characterization?pulp and mineral surface chemistry?flotation kinetics and entrainment?extensive internal and external manpower?Brunswick, Noranda Technology Centre?CanMet, AMTEL, MinnovEx, Lakefield Research, McGill University?small capital expenditure

May 1, 2002

By M. G. Dellow, D. W. Hendriks

"In early 1988 the decision was made by Noranda Minerals Inc. to install pressure filters at the GECO mill to replace the vacuum disk filters and bunker-C fired rotary kiln dryers. Two filters were installed, one for copper concentrate and one for zinc concentrate. Completion of the project was scheduled for the third quarter of 1989. The filters were made operational in October 1989. Some work remains to be done yet on loadout conveyors for total project completion. Capital expenditures for the project have been approximately $2,700,000 to date. The paper describes the selection criteria for the filter, the installation, startup and associated problems.1. INTRODUCTIONThe filter model chosen for the project was the Verti-Press model VP-50-6(7) (Figures1 ,2 and 3) by Filtra Systems of Farmington Michigan, USA. The decision to purchase the Filtra Systems filter was based on gaining familiarity with a different, mechanically simpler pressure filter than the Larox design and to a lesser extent a necessity for repairs to the the disc filter, rotary kiln dryer system used at the GECO operation for its' copper and zinc concentrates. The fact that it is manufactured in North America was an important consideration. The same basic principles of pressure filtration as the Larox machine are used but the implementation is quite different and somewhat simplified with some interesting innovations. 2 filters were installed to allow direct and immediate comparison of the same machine on both fine and coarse materials. Copper concentrate is reground for cleaning on the flotation circuit while zinc is not. Screen analysis of composited samples of concentrates for 1988 indicated that expected copper concentrate would be approximately 66% minus 400 mesh and zinc 50% minus 400 mesh (Tables 1 & 2).The filter is composed of six horizontal chamber module layered vertically and held together in a frame by 1 O large bolts; torqued down to 4000 ft-lbs. 6 individual belts are used; each with its own drive system. The belts themselves are of a 3 piece design with a filter cloth portion, a support belt and a rubberized intermediate portion. They are held together with steel clipper lacings. A basic description (1) of the filter operation is as follows. ""The horizontal filler chamber is closed by hydraulically pressurizing seals across each end of the filter chamber to 200 psi. The feed pump then pumps slurry into the filter chamber. Suspended solids are retained on the filter belt and the filtered solution drains into a lower drip tray and flows from the filter by gravity. At the end of the filtration or feed cycle, a rubber diaphragm in the filter chamber is pressurized hydraulically to 100 psi pressure. This removes all free liquid from the filter chamber and the filter cake. After the diaphragms are retracted the filter cake is blown with compressed air to remove any residual cake moisture. The seals are then retracted and the belt is advanced to discharge the filter cakes. During the cake discharge the belts are washed with a spray header located at the drive end of the filter. The belt assemblies move one (1) complete revolution during the cake discharge cycle. The cycle automatically repeats until the filter is shut down by the operator."

Jan 1, 1990

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007

By Maureen McGuiness

"The pastefill circuit at the Bell Allard Mine in Matagami, Quebec started up in August 1999. The surface pastefill plant produces a cemented paste which is sent underground by gravity through a vertical pipeline in the mine ventilation shaft. Difficulties with paste flow during the start-up highlighted the importance of understanding paste rheology and the effect of operating procedures on line wear. By June 2000, the original circuit had been modified to include a paste pump to transport the paste to the shaft.The steps taken during the paste plant commissioning are discussed. The final flow sheet is presented, focussing on the use of instrumentation to ensure full column flow and proper distribution underground. Resistance modelling and accelerated curing of samples are examined as possible ways of predicting paste resistance to ensure compliance with the mine’s paste specifications.INTRODUCTIONCommissioning a new plant can be difficult and time consuming. The start-up of Noranda’s Bell Allard paste backfill plant was no exception. Since the first day it went into operation, the paste circuit could not meet the tonnage and paste quality requirements of the mine because the paste would not flow by gravity into the vertical pipeline in the mine’s ventilation shaft.Diagnosis of the pastefill problems proved difficult. It was only when the rheology of the Bell Allard paste was understood that the flow problems were solved. To ensure that the paste placed in the stopes meets mine requirements, two methods of paste resistance prediction are being developed."

Jan 1, 2002

By D. L. Blakeman, Trimble. J. W., S. W. Banning

Noranda&apos;s Grey Eagle mine and mill, in the Siskiyou Mountains of northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mineralogy, milling, and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1986

By Gary L. Simmons

Noranda&apos;s Grey Eagle Mine and Mill, located in the Siskiyou Mountains of Northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mining, milling and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1984

By D. L. Stevens

Following an in-depth scenario and strategic-planning exercise in 1997, Noranda&apos;s mine production goal was set at 500 kt/a (550,000 stpy) of both copper and zinc metal in five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in Noranda&apos;s program. The following steps were taken: the exploration and business development groups were combined, teams were formed to search for and respond to opportunity; geologists were coached to become more business minded and engineers were coached to become more optimistic; the company went global; clear thresholds were set, marginal properties were farmed out and other properties were fast tracked; reconnaissance exploration was focussed where there was a clear competitive advantage; and Noranda became a "flexible" partner to juniors and seniors. Is it working? A number of successes, near successes and outright failures are discussed. The main result is a much higher rate of opportunity flux, which is essential for success in the mining industry.

Jan 1, 2000

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda&apos;s mine production goal was set at 500,000 tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: Combined the exploration and business development groups Formed teams to search for and respond to opportunity Made our geologists more business minded and our engineers more optimistic Went global Set clear thresholds, farmed out the marginal properties, fast tracked the others Focused reconnaissance exploration where we had a clear competitive advantage Became a "flexible" partner to both juniors and seniors Is it working? A number of successes, near successes, and outright failures are discussed. The main result is a much higher rate of opportunity flux which is essential for success in the mining industry.

Jan 1, 1999

By C. M. Díaz, P. J. Mackey, P. Coursol

In a recent paper [1], the present authors discussed calculated energy consumption numbers in copper sulphide concentrate smelting for four different smelting technologies. For the present study, from among these technologies, they selected the Noranda/Teniente continuous bath smelting followed by Peirce Smith (PS) converting route to investigate the impact on total energy requirement of some key process variations, such as tuyere injection of dry concentrate vs. slingering of wet concentrate over the molten bath, continuous converting vs. conventional batch PS converting and commercially proven slag cleaning alternatives. In their calculations, the authors used the same thermochemical model and methodology used in their earlier paper. This approach to explore plant design options provides an interesting basis for evaluating flowsheet modifications that could lead to significant copper smelting energy savings. The METSIM software was used in the present paper to carry out heat and mass balance computations for 8 different flowsheet configurations. The results are presented and discussed in the paper with respect to copper recoveries, energy requirements and CO2 emissions.

Jan 1, 2011

By A Coulson, J Hussey

Noranda Inc is a Canadian mining and metallurgical company with its activities managed through businesses in copper and recycling, zinc, aluminum, magnesium and various metals through its interest in Falconbridge Ltd. Noranda operates three base metal mines, three copper smelters, one copper refinery, one zinc refinery, one lead smelter and refinery, three copper recycling and sampling facilities seven aluminum producing facilities and one magnesium production facility in the construction stage. The mining side of Noranda has a strong history of open stope, cut and fill and shrinkage mining. The 1999 Noranda Annual Report lists a 206 million tonne resource located at Porphyry Mountain in GaspT, QuTbec. Mont Porphyre is a large tonnage, low-grade porphyry style Cu-Mo deposit that was discovered in 1994. It is located at a depth between 1.0 and 1.7 km below surface and characterised by a very competent rock mass. The Mont Porphyre resource is located adjacent to the town of Murdochville, close to NorandaÆs Mines GaspT operations. Mines GaspT closed its open pit and underground operations in 1999 after approximately 45 years of mining, but still operates a copper smelter near Murdochville. The low-grade and great depth of the Mont Porphyre resource suggested that mine design could not be based on the conventional Noranda open stoping mining practice. This paper will review NorandaÆs approach to evaluating the Mont Porphyre deposit. The approach included two definition diamond drilling campaigns, a review of current caving practice, an in-house scope study, a geotechnical logging program for diamond drill core and participation in an international study on cave mining. One interesting component of NorandaÆs approach was the scope study that involved a team of multi-disciplinary personnel drawn together for a short period of time. The objective of the scope study was to determine what conditions would be necessary to mine the deposit and to assess the merits of continuing with further exploration work. A review of current worldwide underground bulk mining practices, and in particular an evaluation of the applicability of caving mining methods, were key components of the scope study. The scope study team concluded that derivatives of caving could be applied to the mining of Mont Porphyre, but additional diamond drilling was recommended to further define the deposit and improve the level of geotechnical information. Following the recommendations of the scope study team, a diamond drilling campaign was completed during the summer and fall of 1997. The 1997 drilling campaign had two secondary objectives, in addition to the primary objective of defining the limits of the orebody. The first objective was to improve the level of geotechnical information available for the characterisation of primary block cave fragmentation. The second objective was to improve the delineation of a lower grade intrusive core. A geomechanical investigation was conducted and included particular emphasis on geotechnical data collection and analysis. A review of the actual data collection process, including several trials of different core orientation techniques, will be included in the discussion.

Jan 1, 2000

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda’s mine production goal was set at 500,000tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: - Combined the exploration and business development groups - Formed teams to search for and respond to opportunity - Made our geologists more business minded and our engineers more optimistic - Went global - Set clear thresholds, farmed out the marginal properties, fast tracked the others - Focussed reconnaissance exploration where we had a clear competitive advantage - Became a “flexible” partner to both juniors and seniors

Jan 1, 1999

By André Piché

"Over the last ten years, several developments have been undertaken to conceive a machine capable of carrying out simultaneously all the mining tasks in hard rock deposits: cutting, mucking, hauling, ground support and dust control.The main advantages of continuous mining over conventional drill and blast is the elimination of the cyclical nature of the actual methods. Other advantages sought are improved stability of mine openings, higher productivity, lower costs, and a cleaner and safer mining environment. Noranda has con-tributed to these developments in a major way. As a member of HDRK, Noranda participated in the development of two mechanical continuous mining machines; the TM60 and the Wirth. Noranda also undertook a development of its own based on the utilization of electricity to break rock. This technology is called plasma blasting (PBT). The concept of plasma blasting is illustrated in Figure 1.When the operating voltage is reached (18kV), the energy is released through a high current switch (500k A) into a coaxial powercable. It is then delivered to the tip of an electrode inserted into a drill hole which is filled with an electrolyte (water). When the energy reaches the electrolyte, it is instantaneously transformed into a high temperature, high pres-sure plasma that produces a shock wave capable of breaking rock(1).After initial testing of the plasma blasting technology in the lab and in the feld, two experimental platforms were constructed. The first one, a test bench, was erected at the Noranda Technology Centre in Pointe Claire, Quebec.(2)The second one is a rock breaker prototype based on a standard diesel-powered carrier (Fig. 2). Each platform was equipped with a 300 kJ pulsed-power module.In 1993, the rock breaker prototype was used for an extensive series of tests in the field. During that campaign, over 700 oversized boulders were blasted. The results of the tests demonstrated that more durable components for PBT were needed. The test bench was then used to successfully develop and test long-lasting components (probe, switch, cable, connector) that can be adapted to industrial platforms leading to the commercialization of the technology."

Jan 1, 1996

Nordberg has conducted extensive research, during 1982-85, on the effects of cone crusher variables such as speed, throw and cavity design on the productivity of the crushers. Simultaneously, Nordberg&apos;s engineers have developed advanced design and testing techniques that ensure efficient and reliable crusher designs. Combination of this knowledge has resulted in a design of the MPI000 (1000 hp) crusher which fits on the existing 7ft Symons foundation and yet is capable of producing twice the ton- nage of the 7ft. In this paper the development of the MP1000 crusher and its performance compared to the 7ft heavy duty and super heavy duty crushers will be discussed. Also, substantial cost savings resulting from the application of such a high performance machine will be presented.

Jan 1, 1988

By D. Kaja

The Symons Cone Crusher was invented by Edgar B. Symons in 1923. It was quickly accepted as a superior secondary and tertiary crusher. Nordberg manufactured crushers for the Symons Brothers Co. and in 1928 acquired the Symons Cone business. Since then, the Symons cone has become the standard of the Mining Industry. This is due to the basic rugged design and Nordberg&apos;s continued efforts to modernize and upgrade the crusher design over the years. In 1930, the Heavy Duty model was introduced with a 225 kW (300 HP) rating. Then in 1931 the Short Head version was developed to handle finer crushing applications. In 1950, the 7 Ft. XHD design was produced which provided higher crushing force capabilities for harder ores and for smaller product size requirements. Finally, in 1978, the 7 Ft Super Heavy Duty design was created to expand the power rating to 500 HP and to further increase the crushing force limits. The first 7 Ft. Super Heavy Duty crushers were delivered to Bougainville Copper Ltd. in 1978 for the production of primary ball mill feed in a three stage crushing plant with the third stage in closed circuit. The product size was 80% minus 6.35 mm (1/4 in).

Jan 1, 1998

By Thomas Shumka

El presente texto señala la norma internacional ASIM E2905 aplicada a la limpieza e inspección de corona en los molinos SAG, bolas, engranajes de molinos y hornos donde se busca detectar electrónicamente los defectos de ruptura en la superficie y de dimensionar con precisión, el tamaño de cualquier grieta encontrada en la superficie del material fundido y forjado de la corona y dientes del piñón en molinos SAG y de bolas.

Sep 1, 2014

Lower greenschist quartzo-feldspathic schists within the N-S trending Earnslaw Synform of the Upper Wakatipu area are pervaded by late-stage quartz filled extensional and extensional shear fractures, with quartz-scheelite lodes infilling normal faults. Exposed veins/lodes mapped over at least 1000 km2 define a paleoflow system developed during late metamorphic exhumation of the schist. Both veins and lodes have consistent angular relationships to the schist foliation independent of their location on the Earnslaw synform. Unfolding the synform leads to a regional subhorizontal foliation and a systematic set of subvertical quartz veins striking NNW extending over a depth interval &gt;5 km, striking parallel to a set of normal faults hosting the quartz-scheelite lodes. The structures define an extensional regime with s1 sub-vertical, s3 oriented WSW-ENE, a low differential stress, and suprahydrostatic fluid pressures. &nbsp; The quartz-scheelite lodes (&lt;2 m thick) occupy faults which cross-cut the quartz veins, and are traceable for a few hundred metres, at most. The lodes consist of laminated and/or massive quartz, slivers of crushed and folded schist, random and discontinuous lenses of scheelite with clay selvages separating the lode from relatively undisturbed wallrock schist. Textural evidence suggests that slip developed incrementally with total displacement on faults during lode formation on the order of a few ten&apos;s of metres. &nbsp; The distribution of Glenorchy veins demonstrates broad scale hydrothermal flow through low-permeability schist, channelled within dilatant mesh style structures comprising interconnected shear and extension fractures. Flow through the lodes was likely derived from the greater surrounding area via the interlinked network of fractures and focused into the low displacement shears. Available evidence suggests the system developed together in a uniform extensional stress regime toward the bottom half of the seismogenic regime.

Jan 1, 2001