Search Documents

By G. C. Sun

Rock mechanics properties, i.e. uniaxial and triaxial compressive strength, indirect tensile strength shear strength, Young's modulus, and poisson's ratio were collected for coal and related strata from 50 coal seams in 90 mines. The methodology of data organization and retrieval is described in details. The values and .ranges of those properties are also discussed.

Jan 1, 1993

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By Lewis V. Wade

This paper summarizes the results of the rock mechanics monitoring program performed as part of Old Ben Coal Company's longwall coal mining demonstration project conducted in cooperation with the United States Bureau of Mines. The work described herein included installation of instruments, collection of data and data analysis performed during mining of the first longwall panel in Mine No. 24. The rock mechanics monitoring program included both surface and underground instrumentation and was designed to achieve the following purposes: 1 -To provide the capability to observe unusual situations during mining so that remedial measures could be instituted quickly 2 -To formulate design guidelines for future longwall mining efforts; 3 -To evaluate surface subsidence, and its character, rate and potential effects on cultural features, and to develop criteria to assist in predicting subsidence for other mines having similar roof conditions. Six previous attempts with longwall methods in Old Ben Coal Company's Hine 21 had been unsuccessful due to roof control problems. A description of these attempts is given by Moroni (1973). In preparation for the present longwall operation a study was performed to review existing data on the previous unsuccessful attempts, to establish coa1-and floor-strata bearing capacities in Mines Nos. 21 and

Jan 1, 1977

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

Jan 1, 2003

By Charles A. Bankston, John C. Rowley, Robert J. Hanold, Joseph W. Neudecker

The basic concepts and processes of soil and rock melting as applied to excavation technology are reviewed. The electrically heated, small diameter prototype penetrator development sequence is presented. Emphasis is placed on the different methods of handling the fluid rock and soil melts and their significance in providing new solutions in hole support and debris handling problems. The refractory materials requirements, penetrator life and electrical heater technology are presented. Consolidating penetrators, which form stable glass-lined holes in low density rocks and soils, require no debris removal and will find applications in horizontal holes for utilities, cables, and pipeline installations. Extruding penetrators are being developed to make holes in dense, hard rocks. Melt is conditioned into a variety of debris forms, i.e., glass rods, pellets or rock wool, selected to match appropriate debris handling systems. Unique use in drilling into very hot rock or magma for geothermal exploration or production wells is projected. Some of the results of laboratory and field tests of these devices are compared with theoretically derived operating performance. Coring-consolidating penetrators for geological sampling in alluvium are projected to larger diameter self-propelled and guided coring devices for prospecting along proposed tunnel alignments. Application to the melting of annular shafts for pipeline support piles in difficult conditions such as permafrost has been scoped. Conceptual design studies of large diameter tunneling equipment have indicated the system contributions and economic aspects of rock melting relative to material comminution, wall and roof support and materials handling.

Jan 1, 1974

By Dale S. Preece

"The computer program DMC (Distinct Motion Code) [Taylor and Preece, 1989a] was developed in 1988 and 1989 to predict the motion of rock following a conventional blast. DMC executes very efficiently on a CRAY type computer due to the high degree of vectorization and also due to the use of spherical elements [TayIor and Preece, 1989b]. Bulking mechanisms developed specifically for use with spherical elements include rotation-induced dilatation and aspect ratio > 1.0 [Preece and Taylor, 19901. Rotation-induced dilatation allows the radius of the sphere to expand as a function ofsphere rotation to simulate the interaction of corners and sides of blocky rocks. An aspect ratio > 1.0 is achieved by kinematically tieing spheres together."

Jan 1, 1991

By Jean-François Lessard

The performance of rock pass systems has a significant contribution to the economics of underground mines. Operational concerns include hang-ups due to arching of material, blockage and degradation of the rock pass. This papers presents the preliminary results of a comprehensive rock pass database on the engineering and operation of rock pass systems in Quebec underground mines.

May 1, 2002

To precondition a stope in advance of mining and thus reduce or prevent rock bursts. Approach Drill deep holes from a mine opening in a radial pattern in the vein and load and blast to fracture, the rock prior to production mining How It Works Preconditioning of a sphalerite galena vein in a hard gangue of quartz and quartzite creates a zone of softer rock that fails by displacement rather than violently as an elastic-battle mass. However, the entire area must he analyzed carefully so that the stress transfer does not cause problems in other workings of the mine A typical drill hole pattern and explosive loading is shown in the sketch. Hole diameter is about 4 inches and a down-the-hole, type drill is used. Drilling speed in hard quartzite is about 12 inches per minute High pressure compressed air (250 psi) is used to run the drill. An overhand cut-and-fill stoping area on the 7700 level of Hecla Mining Company's Star Mine in Burke, Idaho was preconditioned above and below the

Jan 1, 1981

By A. Brown

IN INTRODUCING the subject of rock pressures, it may safely be assumed that mining men are only too familiar with the physical effects of strata stresses that accompany the extraction of minerals. It may be further assumed that they have, as individuals, arrived at certain conclusions regarding their nature, based upon years spent in observing such phenomena and in learning how to continue mining in spite of them. Such hardly won experience forms the core of what is often referred to as 'pit sense'. This essential type of knowledge is not ?based on theoretical considerations, nor can it be found in text books. It is highly individualistic in nature and almost impossible to pass on from one generation to another in terms of precise rules for guidance. It is this aspect of individual judgment based on practical experience that has led to the significant phrase The Art of Mining.

Jan 1, 1956

ABSTRACTRock stresses can be modified by physicochemical processes.If rock pores allow the ingress of water and oxygen, but are not large enough to permit the exit of larger molecules of weathering products, anomalous rock pressures develop. Rock masses may also be subjected to osmotic pressures developed as water diffuses into pores and joints filled with saline water. Anomalous rock pressures may also develop as gels filling pores undergo syneresis and as salts crystallize from pore solutions.

Jan 1, 1968

By J. G. M. Mukoya, B. Adebayo

"This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90–180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to ‘stall’. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit. IntroductionDrilling and blasting contribute most to the operational cost in opencast mining and have the potential to influence the cost of downstream operations (Aipanda, 2011). The drillability of rocks depends not only on the rock properties, but also on the drilling tools and operational variables. In rotary drilling, rotational speed, thrust, and flushing are the operational variables, and are known as the controllable parameters. Rock properties and geological conditions are the uncontrollable parameters. Although, many attempts have been made to correlate drillability with rock properties, the rock characteristics affecting rotary drilling have not been entirely defined (Hartman, 1962; Kahraman, Bilgin, and Feridunoglu, 2003). The drill bit is forced into a rock surface from the rotary power head, hence creating stresses and cracks at the bit-rock interface. The performance of a particular bit in any formation i"

May 1, 2019

By J. L. Ellenberger

The U.S. Bureau of Mines has cooperated with Cyprus Casa Grande Corporation Cyprus Casa Grande Mine, Cas a Grande, Arizona, since 1988 to assess the hydrology of an in situ leaching test facility. This work has resulted in an in situ design for leaching copper oxide ore that takes advantage of the increased mineral access associated with poor quality rock surrounding mine drifts. Blasting and bulkheads are used to produce readily-leachable rubble and contain and control solution movement, respectively. The design reduces the need for handling solution under high pressures in an injection/recovery system for in situ leaching of underground ore bodies. Early work at the site recognized a stress redistribution zone and increased transmissivity near drifts. Fracture data from a corehole oriented parallel to the dip of the ore body indicated an increase in fracture frequency around drifts a distance of 21 m (70 ft) away from the 5 m (16 ft) diameter drifts.

Jan 1, 1994

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005

By Benedict C. Di Duca

In the underground construction industry. when bidding work, not only is the contractor faced with determining if rock: is in existence within the parameters of his work. he must also estimate the quantity and the most efficient method of removal.

Jan 1, 1990

By Don Reining

The sand and gravel industry in Southern California has made a sizeable contribution to the construction development of the 15 County area in this part of the State. Facing this mineral extraction industry, in the next decade, is a problem of meeting the market demand. The question is, "how can sand, gravel and rock operations be made compatible with goals for sound and attractive community development?" Three basic principal characteristics of the land needed for this-mining industry are: 1. The land must have workable sand, gravel or stone deposits. 2. The land must be properly located for transportation purposes close to the market in order to sell the aggregate at a minimum cost. 3. The land must be zoned so that it will be permissible to mine.

Jan 1, 1967

By E. A. Córdova

Current methods for scratching a piece of rock to obtain or check the characteristics of its component material can sometimes be expensive and time consuming. Scratching a rock core requires an object with a point that it is capable of sliding along the surface of the rock while recording the response from the rock due to the sliding. With the idea of providing a cost efficient solution for a scratch device, a new generation turntable arm, composed of a cartridge with a diamond stylus and a USB output connection to the computer, was used to record the vibrations from the sliding of the stylus along a rock core surface. The output sound from the stylus was captured with the computer as an audio input signal. The raw sound data was recorded in a standard waveform audio format (wav) file, and post-processed using sound spectrum analyzer software (Spectra-Lab) to capture numerical data such as frequency, amplitude, and noise from the file. The results for frequency, amplitude, and noise were compared and plotted against the scanned surface of the rock core in the search for correlations that might represent specific characteristics of the surface being scratched.

Jan 1, 2010

By Ron Woolf, Corry Goumans

This paper describes rock slope remediation performed along America’s first Superhighway, the Pennsylvania Turnpike and in particular, the specialized drilling equipment designed and built by Pacific Blasting to complete this work. This S-month project was performed on an existing rock cut slope within the Bedford Narrows, a gap formed by the Juniata River through Evitts Mountain. These rocks are in the folded Juniata and Tuscarora Formations within the Valley and Ridge Province and strike northeast with near vertical to slightly overturned bedding.

Jan 1, 2001

By Pinnaduwa H. S. W. Kulatilake

A new formulation is given to conduct a probabilistic block theory analysis. A new computer code (BTAC) has been developed to perform both deterministic and probabilistic block theory analyses. The variability of the discontinuity orientation and shear strength is incorporated in the probabilistic block theory analysis. Discontinuity orientation is treated as a bivariate random variable including the correlation that exists between the dip angle and dip direction. BTAC code was applied to perform both deterministic and probabilistic block theory analyses for a part of an open pit mine in the U.S. Needed geological and geotechnical data for the analyses were obtained from field and laboratory investigations. The variability of the discontinuity orientations resulted in important differences between the probabilistic and deterministic block theory analyses results. The results confirmed that the design value selected for the Maximum Safe Slope Angle (MSSA) for a particular region in the open pit mine based on the deterministic block theory analysis can be on the unsafe side. In summary, the results showed clearly the superiority of probabilistic block theory analysis over the deterministic block theory analysis in obtaining additional important information with respect to designing rock slopes.

Jan 1, 2014