Search Documents

By Z. A. Zhou

In Canadian oil sands processing, flotation is used to recover liberated bitumen droplets from oil sands slurries. Similar to conventional mineral flotation practice, a fundamental limitation of recovering bitumen from low grade oil sand ores is its slow and ineffective aeration of the liberated small bitumen droplets. Gas nucleation and cavitation could provide better mechanisms for accelerating bitumen-bubble attachment. A research program was undertaken to examine factors affecting spontaneous bubble nucleation on bitumen surfaces. The results demonstrate that surface hydrophobicity and existence of gas nuclei in process water play a critical role for bubble nucleation. While there are more bubbles nucleated on highly hydrophobic silanated glass surfaces than on moderately hydrophobic bitumen, bubble nucleation on clean hydrophilic glass surfaces is negligible. Heating process water up to 85 ~ 95oC (as used in commercial operation) or boiling tap water prior to gas nucleation tests is shown to remove sufficient amount of gas nuclei existing in the water, thereby drastically reducing the number of bubbles nucleated on bitumen. Enhancing gas nuclei formation in hot process water is identified as a promising strategy to improve bitumen-bubble attachment during oil sands conditioning, and hence to increase bitumen recovery from low grade ores.

Jan 1, 2014

By R. N. Chakravorty, K. K. Feng

"There is growing evidence that modern methods of mining coal increase the risk of spontaneous combustion. Seemingly unimportant at this time, this hazard could prove to be a barrier to growth and development of the coal industry in some areas of Canada. The paper presents bedrock knowledge on spontaneous combustion gathered by scanning and evaluating current technical and research literature. Special efforts have been made to identify significant coal and environmental factors and to establish criteria for susceptibility. In addition to the state-of-the-art knowledge, preliminary results from on-going studies are discussed."

Jan 1, 1973

By H W. Wu, D Humphreys

The structure of a comprehensive research project into mine fires study applying the Ventgraph mine fire simulation software, preplanning of escape scenarios and general interaction with rescue responses is outlined. The project has Australian Coal Association Research Program (ACARP) funding and also relies on substantial mining company site support. This practical input from mine operators is essential and allows the approach to be introduced in the most creditable way. The effort is built around the introduction of fire simulation computer software to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Application of the simulation software package to the changing mine layouts requires experience to achieve realistic outcomes. Most Australian mines of size currently use a ventilation network simulation program. Under the project a small subroutine has been written to transfer the input data from the existing mine ventilation network simulation program to æVentgraphÆ. This has been tested successfully. To understand fire simulation behaviour on the mine ventilation system, it is necessary to understood the possible effects of mine fires on various mine ventilation systems correctly first. Case studies demonstrating the possible effects of fires on some typical Australian coal mine ventilation circuits have been examined. The situation in which there is some gas make at the face and effects with fire have also been developed to emphasise how unstable and dangerous situations may arise. The primary objective of the part of the study described in this paper is to use mine fire simulation software to gain better understanding of how spontaneous combustion initiated fires can interact with the complex ventilation behaviour underground during a substantial fire. It focuses on the simulation of spontaneous combustion sourced heatings that develop into open fires. Further, it examines ventilation behaviour effects of spontaneous combustion initiated pillar fires and examines the difficulties these can be present if a ventilation reversal occurs. It also briefly examines simulation of use of the inertisation to assist in mine recovery. Mine fires are recognised across the world as a major hazard issue. New approaches allowing improvement in understanding their consequences have been developed as an aid in handling this complex area.

Jan 1, 2005

By Z. Yanni, W. Xuan, Z. Jingyu, D. Jun

"In order to conserve the coal resources, many coal mines which have been mined begin to re-mine. Re-mining face is of complicated circumstances and coal spontaneous combustion is unknown, so experiments are designed to study the characteristics of multiple oxidized coal samples. The investigation into the oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. The non-caking coal is collected as coal samples. The raw coal sample with initial oxidation and the sample after second oxidation and third oxidation are obtained after a certain treatment of the coal. The temperature-programmed system, and proximate and ultimate analysis are adopted to compare the releases of gaseous products of spontaneous combustion characteristic parameters of the multiple oxidized coal sample. With the increase of oxidation times, experimental results indicate that the oxygen consumption rate, the release rate of carbon monoxide and the intensity of heat release are significantly decrease. The characteristic temperature dropped and the size of the pores in coal is smaller as well. INTRODUCTION China accounts for 13% of global coal resources [1-2]. In recent years, more and more coal mines begin to re-mine in order to conserve resources. This production mode is to mine coal pillar left by last exploitation or unavailable for mining. In the process of slicing mining for coal seam groups or thick coal seams, the second or multiple oxidation due to the mining-induced effect, may take place in the goaf of the lower seam. So the spontaneous combustion is prone to occur in this area. The study on oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. Scholars [3-7] have discussed the workability of re-mining for coal mines, verify the feasibility of the existing mining technology for re-mining area, and set up the prevention measures of coal spontaneous combustion. But all these measures are only based on on-site observation data, instead of experiment on spontaneous combustion characteristic parameters of re-mining coal samples which have a great importance for early prediction and forecast. The authors aim at investigating the multiple-oxidated coal spontaneous combustion law, and perfecting the coal spontaneous combustion mechanism to provide a basis for the prediction and forecast."

Jan 1, 2015

By Thomas H. Koenning, James R. Boulton

The coal mined by Cyprus at the Shoshone mine near Hanna, WY is highly susceptible to spontaneous combustion. Spontaneous heatings have occurred in the gob of several of the longwall panels and, in some cases, following roof falls. Prevention and detection methods have evolved over the years as more has been learned about the occurrences. Seal design and construction have progressed to reduce air leakage into the gob. Pressure balancing has been successful as a supplement to good workmanship in reducing leakage. Early heating detection has improved as knowledge has been gained. Prior methods of detection relied upon thermocouples detecting a temperature change. Later a gas chromatograph was used to analyze gob gas samples. Initially the products of combustion (POC) were relied upon for detection. Most recently, lack of oxygen depletion in the gob has been used as an early warning of problems. Examples are presented to illustrate the evolution of spontaneous combustion control at the Cyprus Shoshone coal mine. Methods have been developed which minimize the oxygen concentration in the gob and reduce the potential for spontaneous combustion.

Jan 1, 1997

By P Marianelli, J Theiler, B Beamish, A Spillman

The presence of reactive pyrite in waste rock contributes to the hazard of spontaneous combustion in emplacement facilities as it acts as an initiator of self-heating at low ambient temperatures. Organic carbon also present in the waste rocks acts as a fuel at elevated temperatures above 120°C and can lead to thermal runaway resulting in eventual ignition. A new laboratory test method (adiabatic incubation testing) is now available that can identify the presence of reactive pyrite and quantify the self-heating behaviour of the waste rock. McArthur River Mine has a waste rock profile that contains pyritic shale units, which have created spontaneous combustion events in the past. A systematic sampling and testing program is underway to characterise the spontaneous combustion hazard likelihood of the McArthur River Mine waste rocks to provide a sound database for future mine planning of the waste removal and emplacement. This paper presents some initial outcomes of this program and shows the leading practice in spontaneous combustion hazard assessment and management that has been adopted at McArthur River.CITATION:Beamish, B, Marianelli, P, Theiler, J and Spillman, A, 2018. Spontaneous combustion hazard assessment of McArthur River Mine waste rock, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 422–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A Saghafi, S Day

The control of spontaneous combustion in spoil piles is an area of concern for a number of open cut coal mines. Spontaneous combustion in spoil may occur when carbonaceous waste materials are exposed to air. In large piles, the relatively high voidage within the pile may allow sufficient movement of air through the pile to sustain oxidation and heat generation. Over the past decade, ACARP and CSIRO have funded a number of projects aimed at providing a better understanding of the causes of spontaneous combustion in spoil piles and the development of control strategies. Work has focused on prevention measures but has also considered measures available to deal with well-developed fires. Field, laboratory and numerical modelling methods have been brought to bear on the issues. Individual projects have addressed: causes of spontaneous combustion including the relative reactivities of mine waste materials; the use of cover layers to prevent spontaneous combustion; the use of flyash grout to control an active fire; the emissions of air pollutants; and the emission of greenhouse gases. This paper provides a description of the work carried out to date with an emphasis on the major findings of the research and its application to open cut mines.

Jan 1, 2005

By B Poborowski, A Chen

"For some time, the Australian and Chinese underground coal mining industries have evolvedindependently with minimal infl uence on each other. Despite the fact that in recent years severaltechnologies and solutions have become common to both industries, this trend has seeminglycontinued to the point that there are still many important diff erences in legislation and hazardmanagement systems in both countries. Austar Coal Mine as an Australian based and Chineseowned enterprise has a unique opportunity to benefi t from the technology and knowledge ofboth nations. This paper compares the Australian and Chinese approach towards spontaneouscombustion hazard management in order to exchange experience, identify possible improvements and learn from each other."

Jun 1, 2012

By K. K. Feng

"Spontaneous combustion has always been a problem in coal mines and is identified mainly with the mining of low-rank coals. The liability of coals to spontaneous heating is only one of the factors in determining whether spontaneous combustion will occur. However, knowledge of the relative oxidizability of the coal is a useful factor to take into consideration when selecting new coal seams and mining methods for future mine development.Four methods (static isothermal, ignitability, adiabatic and dynamic) have been used to compare the relative liability of Canadian coal to spontaneous combustion and to investigate the mechanism of spontaneous combustion of these coals. Among these f our methods, the static isothermal method is considered to be the best indicator of the susceptibility of various coals to spontaneous combustion. Western mountain coal adsorbs more oxygen and has a higher tendency to undergo spontaneous combustion than the Harbour seam coal of Nova Scotia. It has also been observed that a higher methane content in coal will indicate a lower liability to spontaneous heating."

Jan 1, 1985

By B. Genc, C. Gous

Spontaneous combustion during coal mining operations is a major problem that affects the health and safety of workers and causes environmental problems. The phenomenon is associated with the presence of coal, coal shale, and pyrite. In 2020, a premature detonation incident occurred at an iron ore mine where the waste material contains black carbonaceous shale units known to be associated with pyrite. The spontaneous combustion propensity and properties of samples of the black carbonaceous shales from the mine were examined and compared with samples from the Witbank Coalfield. The spontaneous combustion liability indexes of these samples were correlated with X-ray fluorescence (XRF) and proximate and ultimate analyses using linear regression. The Wits-Ehac Index classification results show that the samples were between medium and high risk. The linear regression analysis showed very poor correlations between the Wits-Ehac Index results and the XRF and proximate and ultimate results. The most valuable relationship found is between the presence of relatively high sulphur (greater than 3%) and ground reactivity with nitrate-bearing explosive emulsion.

Jun 5, 2023

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By Cudmore JF, Rowlands D

Incidents associated with spontaneous combustion of coal have resulted in the loss of many lives and considerable capital and equip- ment. Nevertheless, the factors controlling the propensity of coal to spontaneous combustion are not clearly understood and there is a need for research to study the effects of rank, petrog- raphy, moisture contents, etc. This has been attempted in a study of the propensities of selected Queensland coals to spontaneous combustion. An adiabatic calori- meter was constructed to study the self-heating of a large number of coals. Chemical and petro- graphic analyses of the coals were determined and an attempt was made to relate these propert- ies to the self-heating characteristics of the coal. The results show a strong relationship between rank and self-heating characteristics and that petrographic composition of coal may also be of importance. Some observations on the application of the laboratory results to the practical situation are made as are recommendations for future research.

Jan 1, 1981

By R. M. Falcon

The paper opens with a summary of the major factors responsible for spontaneous combustion in coal discards. These include heat arising from the oxidation of coal and pyrite, and from the weting of dry or oxidized coal and pyrite; and certain petrographic conditions leading to self-ignition of the coal such as low rank, the presence of a high proportion of reactive constituents, and the occurence of highly porous and botanicaly structured inertinite macerals, The analyses of 6 samples from 2 discard dumps in the Witbank coalfield are included, which show that, according to a three-grade classification of liability to spontaneous combustion, one dump is 'reasonably liable' and the other is 'most liable', It is pointed out that factors other than liability to self-ignition determine the possible utilization of such discards, and that the prevention of oxidation is of great importance if they are to be utilized and spontaneous combustion to be prevented,

Jan 1, 1986

By B. Genc

"The risk of spontaneous combustion is well known in the South African coal mining industry. In the coming years it is very possible that the incidence of spontaneous combustion will increase from current levels, due to factors such as an increased rate of mining, re-working of previously mined seams, more stooping and total extraction for underground mines, and higher stripping ratios for surface mines, leading to more spoils. It is also fairly certain that coal mining will face tougher environmental emissions legislation in the near future. To determine the areas where the risks of spontaneous combustion are high, it is necessary to improve on our current laboratory procedures for testing and evaluating coal samples, combining the results with site and field data, and if necessary revising the laboratory rating system to refine our understanding of South African conditions.Currently, laboratory tests are conducted in order to determine both the Wits-EHAC index and the crossing-point temperature which, when combined, give an indication of the spontaneous combustion propensities of the coal samples. This procedure has enabled the establishment of a database of results to review and evaluate South African coal seams. Using this database, the high-risk areas in terms of spontaneous combustion are identified. Tests have been undertaken for five consecutive years, between 2008 and 2012. In total, 119 coal samples from different coal seams and production coalfields have been analysed and classified through a series of laboratory tests. A comprehensive database of these results is available, and is continually being updated as new test results are added. This database will continue to expand, and to provide the basis for an improved risk evaluation methodology for spontaneous combustion"

Jan 1, 2015

By J A. Shonhardt, I Porter

All types of coal are liable to spontaneous combustion to a variable degree according to the inherent characteristics of the coal and also extrinsic factors. In order to successfully extract coal from highly capital-intensive longwall mining operations it is necessary to evaluate and manage any risks that may be present due to spontaneous combustion. A spontaneous combustion risk management plan for longwall mining is described in this paper. This risk management system comprises identification of conditions promoting spontaneous combustion risk, a laboratory or empirical risk classification system, determination of gas ladder, adoption of adequate ventilation plans and gas monitoring systems that will lead to the development of the spontaneous combustion action plan. The risk management system was applied to a greenfield site in NSW in 1992 when prediction of a high-risk category for the coal seam was made. After commencement of production a spontaneous heating problem emerged as predicted. Description of the case history of spontaneous combustion risk management for a longwall operation in this coal seam is included in this paper.

Jan 1, 2003

By Sen S. K, Banerjee D. D, Nandy D. K

It has been stressed that the intrinsic spon- taneous heating characteristics of a coal is not enough in predicting spontaneous fire risk of a mine. The influence of extraneous conditions created from the system of mining operations are also to be reckoned with, A case study was made with a mine in Jharia field, India, being proposed to be developed under short wall method with complete extraction in 4-5 slices followed by stowing.

Jan 1, 1988

By J. R. Long, E. T. Hayes, D. C. Root, R. S. Dean

THE U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities' and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriate applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately applicable. While atomic hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-arc methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1946

By A. V. S. Meyer

The Colloquium held at Iscor, Pretoria, on 28th June, 1988, had as its objective the need for Quality Management Systems in the industry. Case studies of how problems were identified and solved by the use of such systems were submitted.

Jan 1, 1988

Professor G.T. van Rooyen has guided the Department of Materials Science and Metallurgical Engineering at the University of Pretoria in South Africa for the past 32 years. During this period, 54 masters' degrees have been awarded in the Department, and 17 doctorandi promoted. He has also made a major contribution to industry by his incisive analysis, relevant and practical synthesis, and his exceptional talent in innovative design. He is still active in fracture analysis, thermal fatigue, weld simulation transformation kinetics, and fracture mechanics, and continues to contribute to a better understanding of metallurgical problems encountered in practice. He has advised many companies, and has received many honours and recognitions.

Jan 1, 1994

For the past 12 years, the Universities of Stellenbosch and Cape Town have hosted an annual symposium to discuss research topics in Minerals Processing. Since 1987, this meeting has been held under the auspices of the Western Cape Branch of the South African Institute of Mining and Metallurgy, and has enjoyed much national and international support. In 1993, in place of the usual Symposium, the Branch and Universities collaborated with CSM Associates Ltd and Minerals Engineering Journal is organizing the international Minerals Engineering '93 Conference in Cape Town.

Jan 1, 1993