Search Documents

By Ed Revoort, Robert Schippers

In Rotterdam in the Netherlands the project ‘De Zalmhaven’ is being developed. The project consists of the realization of houses, parking facilities, two residential towers of 70 m and a residential high rise of 215 m. An artist impression for the project is given in figure 1. For the high rise a new development in the use of large diameter, drilled piles with a steel casing has been successfully utilized. In this article the installation method of 65 m long steel drilled piles in two consecutive sections is presented. The settlements for the building (and the influence on its surroundings) have been analyzed in detail using 3D Finite Element calculations, which will also be discussed. Finally there is focus on the results of settlement measurements carried out during construction in relation to the settlement prognosis.

May 1, 2022

By D. M. Avant, S. M. Pickering

A variety of grades of very white muscovite mica are now being produced from sedimentary sands and clays in Central Georgia. The mica is naturally concentrated near the base of the lens-shaped kaolin deposits and also disseminated in associated quartz sands. The same weathering and bacterial alteration processes which have transformed the kaolins from dark organic muds to white pigment-grade industrial clays have also removed discoloring iron from the micas and developed unusually white muscovite. Further, chemical alteration has removed some potassium from the muscovite atomic structure, resulting in an easily delaminated mica which can be cleaved to unusually fine, high bulking, high aspect ratio products. The peculiar alteration history of these sedimentary micas enables production of some of the whitest, finest particle size, and thinnest aspect ratio muscovite mica products on the world market today. Raw mica feed is obtained from kaolin and sand processing by-products, and also from beneath the useful base of abandoned kaolin mines. The processed ultrafine and filler grade muscovite mica products are used for paint, plastics, cosmetics, mold release, thermal and electrical insulation, epoxy, and dry wall joint cement markets.

Jan 1, 2002

By Michael A. Knott

Large lateral forces on bridge foundations due to extreme events such as vessel collisions, earthquakes, and wave forces on storm surges during hurricane events are often the controlling design condition for bridge foundations. A review of the American Association of State Highway and Transportation Officials (AASHTO) vessel collision analysis and design codes used in the United States for highway bridges will be presented. The paper includes the background and development of the AASHTO Guide Specification and Commentary for Vessel Collision Design of Highway Bridges (1991) and vessel collision provisions of the AASHTO LRFD Bridge Design Specifications (3rd Edition 2004 and the approved 2005 Interims). Experience in using the AASHTO codes will be discussed and observations on the adequacy and gaps, comparison with the European Standard Code, and recommendations for immediate and long term needs will be presented.

Jan 1, 2013

By Phil Keele

"Manalta Coal Ltd. 's Vesta Mine will supply Alberta Power Limited's 740 MW Battle River Generating Station with 1 128 000 tonnes of sub-bituminous ""C"" coal in 1983. Mana/ta Coal Ltd. and Alberta Power Limited are in their seventh year of a 31-year coal supply agreement. With the exception of localized topographic highs where three coal seams are mined, the Vesta Mine is primarily a single-seam mining operation. Vesta's comprehensive programs of mine planning, preventative maintenance, reclamation, and employee relations make it an efficient and a well run operation. Introduction The Vesta Mine, located in east-central Alberta approximately 300 km northeast of Calgary, supplies sub-bituminous ""C"" coal to Alberta Power Limited's 740 MW Battle River Generating Station. The coal reserves and principal stripping equipment are owned by Alberta Power Limited. Manalta Coal Ltd. owns and operates the additional mining equipment and support facilities. Coal production is from a single pit, 3.5 km in length. Both single and multi-seam operations are encountered in the active pit. In 1983, production is anticipated to increase to I 128 000 tonnes from 906 000 tonnes in 1982. The additional tonnage will be achieved by operating 24 hours per day, 5 days per week. The following sections briefly highlight historical, geological and mining/reclamation aspects of the Vesta Mine. Figure I illustrates the location of the Vesta Mine in relation to the cities of Calgary and Edmonton. History Coal mining for domestic use began near the turn of the century in the Vesta Mine area. Initially, small underground room-and-pillar operations were dominant. As equipment technology advanced, surface strip mining replaced the underground methods."

Jan 1, 1985

By K Akiro

Volcanogenic massive basemetal sulphide and gold mineralisation of predominantly low sulphidation style has been located within Lower Tertiary basaltic and felsic volcanic and sedimentary sequences at Ufuo, in the Left April River area, northwest Papua New Guinea. The four discrete massive sulphide bodies, which have been so far identified, occur within a 3 +5 km area situated within a north west trending structural corridor. The sulphide bodies are all localised on the margins of the corridor where the bounding major through going faults are transected by regional faults. Mineralisation is characterised by massive pyrite-bornite-sphalerite-barite-quartz-anhydrite deposition with later galena-tennantite-chalcopyrite. Minor phases include enargite, goldfieldite and bismuth sulfosalts. Jasperoidal silica lenses and bioturbated sediments are closely associated with the massive sulphides. Basemetal sulphide mineralisation is also closely associated with phyllic-style quartz-sericite- altered host rocks underlying the massive sulphide lenses. This mineralised phyllic alteration is localised to fractures, veins and breccias that cross-cut propylitic style alteration characterised by quartz, epidote, chlorite, adularia and zeolite. The mineralised system possesses several hydrothermal features consistent with a copper-rich submarine exhalative volcanic hosted massive sulphide (VHMS) system, ie discrete massive sulphide bodies with abundant barite, associated jasperoidal silica and bioturbated sediments. However, exploratory drilling of the alteration zone underlying each of the massive sulphide bodies has not identified a well-defined zoned alteration pipe that is characteristic of such systems. The alteration is also similar to that of a porphyry-related low sulphidation system in which phyllic alteration has overprinted a regional propylitic style assemblage. The presence of sporadic enargite (and ?tennantite/tetrahedrite) suggest there were intermittent pulses of acid fluids in the system probably derived from exsolved magmatic SO2 which flowed directly to the surface along reactivated faults. The occurrence of tellurium and bismuth minerals is also consistent with a magmatic contribution to the metalliferous hydrothermal fluids. It is proposed that the VHMS orebodies are the products of submarine exhalative deposition generated by a crystallising magma emplaced within crust of on-going tectonism. Ufuo mineralisation is similar to many VHMS deposits elsewhere in that it is unclear whether the metals are derived from the magma directly, or via seawater leaching of the wallrock. Additional studies such as oxygen isotope analysis may assist in resolving this issue. If the metals are shown to be of direct magmatic origin then there may be good prospects for discovering economic-grade porphyry-related mineralisation at depth below the massive sulphide deposits.

Jan 1, 1999

By Paula Rodrigues Caumo

A aterosclerose é um termo geral relativo a diversas doenças relacionadas ao espessamento e perda de elasticidade da parede arterial. Atualmente os maus hábitos alimentares, combinados ao sedentarismo, podem levar a ocorrência de elevados níveis de colesterol na corrente sanguínea. Este fato aumenta o risco de obstrução dos vasos sanguíneos, limitando o fluxo do sangue para o coração. Desta maneira, para desobstruir o vaso sanguíneo e manter o lúmen arterial aberto é colocado um stent. Os stents são redes, normalmente de ligas metálicas, que servem para desobstruir os vasos sanguíneos. O tratamento de doenças das artérias coronárias e periféricas usando stents metálicos tem sido adotado nas intervenções médicas nos dias de hoje. No entanto, surgiram argumentos que indicavam os benefícios de remover o stent após este ter feito a desobstrução, originando desenvolvimento de stents biodegradáveis. Estes exigem propriedades mecânicas adequadas, biocompatibilidade adequada, garantindo uma baixa toxicidade dos produtos de degradação. Com isso, o objetivo deste trabalho é o estudo preliminar sobre stents metálicos biodegradáveis, como ferro puro, magnésio. Além disso, avaliar se os mesmos são adequados para aplicação à stents biodegradáveis, avaliando as propriedades mecânicas dos metais, biocompatibilidade e toxicidade dos compostos degradados ao longo do tempo de implantação.

Aug 17, 2017

By Franciéli Mantovani

Apesar da primeira preocupação com relação à gestão de resíduos ser a busca pela minimização da geração dos mesmos, há muitos casos de processos produtivos que geram resíduos inevitáveis. A investigação e o desenvolvimento de processos tecnológicos capazes de transformar os resíduos no sentido de reutilizá-los são plenamente justificados e passaram a ser uma realidade. Dentro deste panorama, a reciclagem de resíduos potencialmente perigosos, como o pó de aciaria elétrica - PAE, é uma importante questão ambiental. A indústria de pigmentação, na busca de matérias primas alternativas e de menor custo, vem apresentando potencial para absorver resíduos que contenham elevados teores de ferro sob a forma de óxidos. Neste sentido, esta pesquisa objetivou avaliar a viabilidade do uso de PAE para pigmentação da fração argamassa do concreto. Para tanto, foram moldados três traços diferentes, com teores de adição de PAE e de pigmento comercial de 0% e 5%, mantendo-se uma relação água/aglomerante de 0,4. Para cada traço moldaram-se corpos de prova destinados aos ensaios de resistência à compressão e de medições colorimétricas. A partir dos resultados obtidos, verificou-se que o PAE apresenta potencial para pigmentação de argamassas. Entretanto, verificou-se retardo na pega do material, o que pode vir a prejudicar a desforma.

Jul 30, 2018

By Mariella Cortez Caillahua

No presente estudo o gesso FGD (flue gas desulfurization) foi avaliado como aditivo retardador do tempo de pega, substituindo o gesso natural na fabricação do cimento Portland (CP II E-32). Os resultados da caracterização físico-química e morfológica do gesso natural e do gesso FGD identificaram um material de alta pureza, sulfato de cálcio di-hidratado para o gesso natural e a presença, principalmente, de bassanita (CaSO4.0,6H2O) e hannebachite (CaSO3.0,5H2O) com baixas concentrações de impurezas no gesso FGD. Baseado nos resultados, o gesso FGD é uma alternativa adequada para substituir o gesso natural. O tempo de pega mostrou cerca de uma hora de retardo em comparação com gesso natural e seu efeito sobre a resistência à compressão para as amostras de 3, 7 e 28 dias dependem da composição das misturas, atingindo um valor máximo para a argamassa com 2,1% de gesso FGD e 1,4% de gesso natural. Seguindo a norma ABNT NBR 10004:2004 o resíduo é classificado como não perigoso e não inerte.

Aug 8, 2018

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By V. Bazhko, V. Yahorava

The calcium sulphate waste stream of the wet phosphoric acid process, commonly called phosphogypsum (PG), contains the majority of rare earth elements (REE) initially present in the apatite feedstock. Mainly light and middle REE are present in PG and their total concentration ranges from 0.27% to 0.35% by mass. Worldwide, around 7 billion tonnes of PG have been produced to date at a current growth rate of 150-200 million tonnes per annum. In total, an estimated 21 million tonnes of REE are locked in PG waste dumps around the world. Due to the value of the REE contained in PG dumps a number of processes have been devised for their recovery. The majority of these processes applied complete or partial gypsum dissolution, but were deemed not viable due to high capital and operating costs. Mintek developed an alternative method for the recovery of REE from PG by applying Resin-in-Leach (RIL) technology. This technology was tested on PG sampled from dumps and current arisings from South African phosphoric acid production plants. The extensive testwork program included evaluation of various lixiviants and optimisation of lixiviant additions, optimisation of REE leach and adsorption conditions, batch equilibrium and kinetic adsorption tests, continuous RIL testwork and numerous variability tests. It was found that PG from different sources was highly variable, both in terms of REE recovery as well as physical properties of the material such as viscosity and filterability of the slurry. The recovery of REE varied from 15% to 80% depending on the origin of the samples. A high-level economic study indicated that at a price of >21 $/kg for mixed REE oxide product in conjunction with an overall REE recovery as low as 15% the economics of REE recovery from PG via RIL technology may already be favourable.

Jan 1, 2016

By B D. Saffron

In 1983, open cut coal mining operations were suspended at the Tent Mountain coalmine, located in Alberta, Canada in an area called Crowsnest Pass. Montem Resources (‘Montem’), an Australian mining company, purchased the asset in 2016. They conducted several drilling campaigns and undertook environmental monitoring with the intent to restart operations. In 2020, Montem completed a Definitive Feasibility Study, which indicated a mine life of more than 14 years.

Aug 2, 2023

By Horacio Reeves

Las maquinarias son elementos importantes en el proceso de minería de tajo abierto -en tanto optimizan el rendimiento del trabajo y de los operarios. Sin embargo, su contínuo uso conlleva riesgos ocupacionales en el trabajador como la exposición a vibraciones de cuerpo entero en el caso de equipos pesados. En ese sentido, el presente texto compara los niveles de vibración en los equipos pesados que operan en Antamina con el estándar europeo: Directiva 2002/44/CE, así como los efectos de este en los operarios.

Sep 12, 2005

It had been more than a decade since this many booths were occupied at an SME Annual Meeting, but at the 2010 meeting in Phoenix, AZ 630 booths were sold to 470 vendors from the entire spectrum of the mining and minerals industry. Exhibitors such as Metso, FLSmidth, West-Tech, ABB, NIOSH, Eriez and Resource West took their usual prominent places on the exhibit floor and were joined by newcomers such as tunnel boring machine manufacturer Herrenknecht AG, Frontier Kemper, the International Society of Explosive Engineers and more than 100 other first-time exhibitors. On the floor, one could find everything from a new pair of boots to a new career in the recruitment pavilion where some of the biggest companies in mining (Barrick Gold, Freeport-McMoRan, Newmont Mining, etc..) set up shop. The following is a look at some of the companies and products that were on display at the 2010 meeting. For information about displaying at the 2011 annual meeting in Denver, CO, Feb. 27 to March 2, contact exhibits@smenet.org.

May 1, 2010

By H. C. Wade

"Description and UseDischarge liners or pulp lifters as they are sometimes called are a trough type liner used at the discharge end of the mill where ground ore passes to the trunnion.There are basically two methods of discharging pulp. The First and most common is the overflow method. Here ground ore travels from the feed to the discharge end where it exits through the discharge trunnion in an overflowing manner, hence the name ""overflow"". (See Figure I) The second method of discharging pulp is the grate method. With this method you block-off the trunnion and hold the ore inside the mill for a longer period of time. This allows only the desired size of ore out of the mill. Ore passes through the grate liners, into the Vibrathane Discharge liner, and finally down to the trunnion. Greater control of the ore size results wit1 this method as compared to the overflow method and it also eliminates reclassifying and regrinding. (See Figure 2)Types in UsePresently the majority of discharge liners in use today are rubber. (Metal insert and rubber covered) In some extremely course applications steel and nihard are used."

Jan 1, 1980

By Albert Musschoot

The expanding applications of vibrating feeders for controlling the flow of bulk materials, and their adaptation for processing requirements, have developed considerable interest in stockpiling and reclaim systems. The general design of these units consists of a material transporting trough, or platform, driven by a vibratory force system. Design flexibility and variety is limited only by engineering ingenuity. The basic motion of the vibratory trough, or work member, is a controlled directional linear vibration that produces a material tossing or hopping action. Material travel speeds vary from 0 to about 30 m/min, depending on the combination of frequency, amplitude, and slope vibration angle.

Jan 6, 1981

By A. Feldman

Measuring dynamic effects on existing structures such as dams and bridges during earthquakes or blasting is frequently done using strong motion detectors. However, a more comprehensive dynamic structural evaluation requires direct measurement of deflection, strain, and pressure changes during dynamic events. Many existing structures have vibrating wire gages already installed that can be used with modifications to the data acquisition systems to provide direct measurement of dynamic displacement, strain, and pressure. The project described in this paper provided the opportunity to demonstrate the feasibility of using vibrating wire technology to measure dynamic effects on existing structures.

Jan 1, 2006

By Jarrett. K. M.

Nobody has, as yet, made a perfect machine. Therefore, when a machine is operating and functioning as it is designed to do, there is always some vibration present. This is easily and simply measurable with present-day equipment and any increase in the amount of vibration will indicate a potential failure. When an increase is noted, vibration analysis can pinpoint the cause of the potential failure and remedial action can be taken before an unscheduled shutdown is necessary or a breakdown occurs.

Jan 1, 1972

By Erica Lorenzo García, Benjamín Cebrian Romo, Antonio Morato Medina

This paper presents the results of a preliminary study on blast-induced vibrations conducted at a Radioactive Waste Storage Facility, located in Spain. The study was undertaken as a preparatory step prior to the blasting operations required for the construction of a new platform located near critical infrastructure housing very-low, low and intermediate-level radioactive waste. The primary goal was to establish a site-specific vibration attenuation curve to safely determine allowable explosive charges based on their distance to sensitive structures. The study followed the criteria defined in the UNE 22.381-93 standard, which regulates permissible vibration levels for different structural typologies. In this case, the existing facilities were classified as Type III structures, given their heightened sensitivity to vibrations. Two experimental campaigns were conducted. Test 1 consisted of a series of 10 individual blasts with increasing charges, monitored by five strategically placed seismographs to record seismic wave propagation and determine the attenuation parameters via regression analysis. Test 2 simulated a production blast using operational charges of 41.7 kg (91.93 lb), applying different delay sequences (42 ms and 25 ms) between holes to assess wave interference, resonance, and constructive effects. Data analysis showed that the longitudinal component dominated vibration transmission, and the predominant frequencies in the most critical zone ranged between 18 and 20 Hz. Based on these values, a conservative peak particle velocity (PPV) limit of 4.75 mm/s (0.19 in/s) was established for blast design. The recorded vibration levels during the tests remained within regulatory limits, with maximum values of 2.35 mm/s (0.09 in/s) and 2.86 mm/s (0.11 in/s) for the sequenced blasts, and peak acceleration of 0.0464g.

Jan 26, 2026

By Jesus Pascual, Benjamin Cebrian

A new Convention Center is going to be built in the millenary city of Toledo, right in the old city limits. The workings will need to excavate some 80.000 cubic meters of granite, which has, a trench-like structure already blasted for the construction (60 years ago) of a parking lot and a shopping area. Surrounding this trench, some few feet away, there are structures and buildings from the 16th century and remainings from previous times that need to be preserved from any damage caused by blasting. Because of this, a vibration analysis was designed according to the special characteristics of this work. Structures to monitor were located at several levels. It considered three different directions of study in order to evaluate the impact of vibrations of the structures located at three different heights of the granite trench. On top, the historical convent of Santa Fe, with some remaining from the 8th century (Muslim domination of the Iberian Peninsula), on the bottom, the Justice Hall of Toledo with 16th century walls, and, in the middle, a wall and a tower from times of the king Phillip II (16th century, the time of the Spanish Empire).

Jan 1, 2004

By B. K. Mishra

In order to maintain higher grinding efficiency in tumbling mills the mill interior and dynamics must be known. For this purpose, several different types of non-intrusive methods have been proposed and are being tried in the industry. We have made an effort to develop a diagnostic tool based on vibration signal. Here we discus results of our experiments pertaining to ball as well as SAG mill. In each case, a triaxial accelerometer was used to capture mechanical vibration generated due to the tumbling action of the charge. The vibration signal was transmitted to a remotely placed computer and the signals were analyzed by standard signal processing technique. In case of a ball mill (5m diameter), qualitative mill information could be obtained by correlating the vibration signal to feed rate and mill filling. An effort was also made to identify different motion characteristic of the charge by analyzing its vibration signal. In case of the SAG mill (10m diameter), liner wear was estimated by comparing the vibration signal emitting out of a freshly lined mill with that of a worn out mill.

Jan 1, 2011