Search Documents

By S. H. Ash

IN no part of the world other than a small area in Pennsylvania is anthracite mining an industry of major magnitude. As the deposits of anthracite in the United States are limited virtually to Pennsylvania, the difficulties of this industry have been commonly considered a state rather than a national problem. However, there is also national interest in the conservation and wise utilization of all the country's fuel resources and in the control of interstate waterways. The anthracite industry is confronted with a serious problem of water accumulation in many of the mines, a problem that must be solved in the near future if progressively higher mining costs are to be avoided. It cannot be solved by the operating companies without state or Federal aid, or both, owing to the magnitude of the work required, the diversity of interests of the coal and surface ownerships, the hazard to the whole mining community, and interests affected outside the mining region. 'The costs of abating the ever-increasing surface seepage to mine workings and of handling this seepage once it has occurred are beyond the eco¬nomic resources of the operating managements.

Jan 1, 1941

By Wm. C. Coffin

THE refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Not only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts clown the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bes-

Jan 2, 1919

J. S. UNGER,* Pittsburg, Pa, . (written discussion?).-The author of the paper has given an excellent description of the appliances used to cool parts of an open-hearth furnace, and some of the reasons why the refractories fail in service. Personally, I favor water-cooling, but to a limited degree. At one time I advocated more universal cooling than is now practised, but believe I must change my mind. Water-cooled, thin-lined blast furnaces have not proved as satisfactory as anticipated. While this may retard the building of many such furnaces, it will not prevent the use of regular tuyere- and bosh-cooling appliances. Water-cooling any furnace may be easily carried to the extreme. In an open-hearth furnace, excessive port or roof cooling, or cooling the working floors may preserve the lines of the furnace, lower the cost of refractories, acid to the comfort of the workmen, and necessitate fewer shutdowns for repairs, but it may not be good economy on account of the high first cost, the cost of cooling water, maintenance of cooling appliances, and the immediate reflection in a higher fuel cost. The question becomes a financial one, and is answered by using water-cooling devices up to the point at which they cease to show true economies. Open-hearth furnace bulkheads, roofs, and ports fail rapidly in about the order named. If they could be made to last indefinitely by water-cooling, the furnace would still have to be shut clown periodically for cleaning the slag pockets, regenerator chambers, and flues. Extra, or spare, pockets and regenerator chambers have been advocated to permit of continuous operation, but the space required, the cost of installation, and the fuel required to initially heat such cold chambers will largely prevent their adoption. Some particular fuels, as high-ash powdered coal, require frequent stoppages for cleaning, but for this particular fuel a special provision can' be made.

Jan 5, 1919

ROBERT M. KEENEY,* Portsmouth, Ohio (written discussion?).- Mr. Coffin has written a most interesting paper that covers most of the uses to which water-cooled devices are subjected; but to meet with the operating department's approval, these devices must effect a saving in cost per ton of ingots produced in the furnace. The making of steel in the open-hearth furnace is dependent entirely on the personal element. It is not possible to charge the furnace with so much raw material, turn on a valve for heat, and by use of recording thermometers, clocks, etc. empty the furnace when a steel is made. Competent men trained to the work must be in charge all the time, and the quality and quantity of steel produced is quite as dependent on the care and working qualities of the furnaces as on the raw material and working of the charge itself. Steel making is hot, hard work and the inducement offered to technical men to take up this work is not sufficient to induce many to enter the field. The result is that most of the workmen in an open-hearth plant, the men who actually operate the furnace and make the steel, are not technical men and do not understand the "whys" and "wherefores " and care less. All this means that a furnace must be built as nearly fool-proof as possible. By this I mean that it is necessary to protect those parts of a furnace most subject to abuse by water-cooled devices whenever possible, and these water-cooled appliances must he as nearly fool-proof as they can be made. The control of the gas entering a furnace is of the utmost importance. This means a properly designed port must have the same design throughout the whole run of the furnace. This is not possible with the ordinary

Jan 6, 1919

By Y. Maeda

Non-ferrous smelting furnaces generally install a gas cooling system for treatment of waste gas containing SO2,. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system is the best way to cool gas, however this system requires high initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled jacket system, are more suitable if the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In additton, the water-cooled jacket system is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace was planned in our factory and it was necessary to install waste gas cooling equipment. In our case, a water-cooled jacket system was more feasible because of the low gas volume and high dust content. It was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cooled jacket had been experienced in the past. That is because SO2 In the waste gas changed into sulfuric acid which corroded the jacket material. As the first step, several data from actual' usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled jacket system was newly designed and tested for three months in a pilot plant. After this system's performance was confirmed, it was installed in a new furnace as a commercial plant. After one year of operation, the initial thickness of carbon steel jacket remains almost the same.

Jan 1, 1992

By Y. Maeda

Non-ferrous smelting furnaces generally lnstal1 a gas cooling system for treatment of waste gas containing S02. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system Is the best way to cool gas, however this system requires high Initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled Jacket system, are more suitable If the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In addition, the water-cooled Jacket system Is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace. was planned tin our factory and It was necessary to install waste gas cooling equipment. In our case, a water-cooled Jacket system was mo11e feasible because of the low gas volume and high dust content. H was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cool1ed Jacket had been experienced In the past. That is because S02 in the waste gas changed into sulfuric acid which corroded the Jacket material, As the first step, several data from actual usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled Jacket system was newly designed and tested for three months in a pilot plant. After this system's performance was confirmed, It was installed In a new furnace as a commercial pl.ant. After one year of operation, the initial thickness of carbon steel Jacket remains almost the same.

Jan 1, 1992

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

By L. Alan Weakly

The U.S. Department of Energy (DOE) has entered into a $l.5 million Cooperative Agreement with Alpine Equipment Corporation/Astro International Corporation ("Alpine") of State College, Pennsylvania, for the evaluation of water-jet-assisted (WJA) mechanical cutting of oil shale under actual mining conditions. A commercial-sized, heavy WJA mechanical miner is being assembled based upon the successful "factory testing" of a smaller prototype miner utilizing standard tungsten-carbide and Polycrystalline Diamond Composite (POC) bits in large oil shale boulders. Actual field testing of the machine will be conducted in an oil shale mine located in the Piceance Basin of Western Colorado. In-mine logistical support is being provided by several oil shale companies through the Colorado Mining Association (CMA) and the U.S. Bureau of Mines (USBM).

Jan 1, 1990

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987

By JULIAN HINDS

Industrialization is raising the standard of living of people everywhere. The common man is demanding and getting more of everything. Perhaps more markedly than most other things, he is consuming more water. A hundred years ago water for domestic use, in all but a few large centers, was lugged from wells in buckets. This still is true in many rural areas, even in the enlightened United States of America. but pumps and pressure systems are rapidly replacing the "old oaken bucket," even on farms and in isolated country homes. Nevertheless, many still fail to see water as a ?commodity? in the same sense that coal, lumber, fertilizer, and bread are considered as commosities. Water is too frequently taken for granted.

Jan 1, 1949

Capture airborne respirable dust generated by an auger-type continuous mining machine to reduce workers' dust exposure. Approach Install a water-powered scrubber system, operating at 1,400 psi, on the sides of the conveyor. The scrubber draws the dusty air from the face area and discharges cleaned air into the face return. How It Works Auger-type continuous miners pose unique ventilation and dust control problems. To protect face workers from the dust, the end of the brattice is usually maintained close to the face to increase ventilation effectiveness. However, it is taken down as the machine cuts toward the exhaust side to allow the machine to complete its cut. Often, the brattice is not reinstalled in a position to most effectively control

Jan 1, 1989

Develop technology that can reduce the dust exposure of a mine worker at the tailgate end of the longwall face by providing him with a clean split of air. Approach Use the jet spray air mover (JSAM) developed under a Bureau of Mines contract (refer to Technology News No. 117 for details on the development), to clean a small portion of the face air and to discharge the clean air behind a brattice partition. How It Works At most longwalls, air flows along the face from head-to-tail. Most of the airborne respirable dust generated along the face during mining is transported to the tailgate with the airflow. Any miner required to work at the tailgate is exposed to this dust. The only practical means of removing airborne respirable dust is with a scrubber. Simplicity and size made the JSAM the best choice for cleaning a portion of the tailgate air. The scrubber has no moving parts and is operated by water at low flow rates (<10 gpm) and fairly high pressures (250-500 psig). Many longwalls have sufficient water systems to supply the JSAM with adequate water pressures and flow rates. Also, the JSAM&apos;s size (4&apos;x 2&apos;x 1&apos;) allows it to be hung on one of the tailgate&apos;s shields or at some other convenient location. A clean split can be maintained at the tailgate by discharging the cleaned air behind a brattice partition at the work area. This should effectively seal off the clean air from the dusty air and provide the tailgate worker with a less dusty work environment.

Jan 1, 1983

Reduce workers&apos; dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the boom of a continuous miner at the conveyor throat. Dusty air from the face area is drawn through the scrubber and cleaned air discharged into the return. How it Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator and contaminated air behind the line curtain to the return. The problem with exhaust ventilation is that the line curtain should be within 10 ft of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back towards the operator. An effective way of removing this dust is with a scrubber mounted on the mining machine.

Jan 1, 1988

By G Mudd, N Haque, S A. Northey

Life cycle assessment (LCA) provides an internationally standardised framework for estimating the environmental impacts associated with products or services (International Organisation for Standardisation, 2006). A particular strength of LCA is the ability to consider indirect impacts that occur at different stages of a product’s life (eg raw material acquisition, manufacture, use, disposal or recycling) and through its supply chain (Figure 1). A wide variety of impact categories are able to be considered by LCA, such as the potential contribution to global warming, ozone depletion, marine eco-toxicity or freshwater eutrophication.CSIRO has a long history of using LCA to compare the environmental impacts associated with alternative mining, mineral processing and metal production technologies (Haque and Norgate, 2014; Norgate and Haque, 2012, 2013). These ‘mine-to-metal’ assessments have primarily focused upon estimating embodied energy and greenhouse gas impacts associated with these production processes; however, more recently there has been a refocus to also consider consumptive water-use impacts in more detail (Northey et al, 2014).CITATION:Northey, S A, Haque, N and Mudd, G, 2016. Water-related data requirements for improved life cycle assessment of mining, mineral processing and tailings management, in Proceedings Life-of-Mine 2016 Conference, pp 16–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Kenneth L. Nash

The control of solubility of waste actinide ions, by conversion to highly insoluble mineral phases has been demonstrated in the laboratory. Actinide metal ions are removed from neutral pH solutions by a combined ion exchange-decomposition-mineralization process based on the application of the naturally-occurring hydrolytically unstable.polyphosphate organic compound phytic acid.

Jan 1, 1999

By S. A. Pence, A. I. McCallum, V. de Korompay

"Special salt protection rings containing a water-swell• able, polymeric sealant are in successful operation in Canadian potash shafts. Installed above the Prairie Evaporite salt formation at a depth of 3,000 feet, the sealant is preventing formation water migration into the salt and pressure build-up on the concrete lining of both production and service shafts. The salt protection rings are not under the hydrostatic pressure of the formation water.The chemical sealant in use has the unique property of imbibing water and swelling. •Therefore, any water at• tempting to flow by the seal ring actually produces a tighter seal.The purpose of this paper is to discuss the sealant and its properties and uses. Installation of the material and its operation in two Canadian mine shafts is described."

Jan 1, 1971

By Ram V. Ramachandran

As an industry with major potential impacts (both good and bad) on water resources and due to the rising costs of process water, the mining and metallurgical processing industry has a key responsibility to contribute to the overall goal of preserving both the quantity and quality of water available within the watersheds they operate in. As we plan for new and existing mining and metallurgical projects, we need to consider a hierarchy of options to minimize our impact within the watersheds we operate; keeping clean water clean by diverting around our operations; reduction in the amount of water we use; reuse of water wherever possible, and improvements to water quality for recycling and/or release to environment. Technology is needed to treat water to improve its quality for reuse or release to the original watershed. While lime precipitation followed by sulfide polishing is effective for removal of most of the metals, it does little or nothing to remove ammonium ions and anions such as chloride, nitrate, molybdate, arsenate and selenite/selenite. Regulations on sulfate limits in treated discharge water has drawn close attention to the treatment of acid mine drainage (AMD). Management of brine and salt disposal is also posing a problem due to strict regulations and cost of disposal. This paper will: (a) address issues associated with managing water with the objective of maintaining water sheds—status quo-during and after operation (b) discuss potential technologies for advanced water treatment plants.

By Raphael G. Kazmann

Water occupies a dual role in our industrial society. It is the indispensable raw material, essential to life itself. It is equally an industrial nuisance, interfering with the production of industrial minerals, making construction difficult, flooding valuable land, and generally producing problems because it is in the wrong place at the critical time. The legal position of water as a nuisance, and the counter measures to be taken, have been well established procedures for determining the responsibility for damage caused by water, and the organization of drainage districts and flood control and levee districts have been legally tested many times. Thus there is rather adequate legal doctrine concerning water, the common enemy. But recently efforts have been made to regularize the position of water as a useful, industrial, commodity. Such laws are not new to the West, where the doctrine of appropriation for beneficial use is slowly becoming the water law. Elsewhere the University of Michigan has produced a "model" water law and efforts are being made to induce all of the states to use this law, or a slight variation of it, as the basis for legislation. There are many serious criticisms of the proposed "model"-law, and the writer strongly opposes many of the provisions. But the fact remains that water is, in itself, so useful and essential that laws have been, and will be, passed to insure the orderly development of our water resources and to prevent waste. The, most important aspect of these "water-use" laws is that, wise or unwise, the existing laws and the proposed laws have been "water oriented". "Water oriented" means that it has been tacitly assumed that the beneficial use of water, either surface water or ground water, is the overriding consideration.

Jan 1, 1960

By Frederick J. Browne

Water, water everywhere, but not a drop (fit) to drink! Trite, but how often only too true? What is there met with in mining which, under various circumstances, may be said to be the most sought-for and highly-prized and also the most objectionable and most feared? Water! What visions that combination of five letters brings to all thoughtful minds? Up to near the end of the eighteenth century water was thought lo be an element but was then discovered to be the result of the combustion of two volumes of hydrogen with one volume of oxygen, and water so produced is chemically pure. Pure water is a clear and colourless liquid when seen under ordinary conditions, but appears bluish when seen through a long tube, and this same bluish tint may be observed in many lakes, especially those of glacial origin. A story often told describes a prospector in the desert who, failing to find water to replenish his canteen, suffers torture and death under fearful circumstances. Then again we may recall the flooding of mines, where water poured in so quickly that there was no opportunity of saving the unfortunate workmen. Instances might be multiplied without number showing that either the lack or excess of this essential fluid has taken heavy toll of human life. In all branches of mining and associated industries water must be dealt with to a larger extent, from an economic point of view, than any other substance, and very often the purity of the water is a matter of considerable importance.

Jan 1, 1925

By E. S. Geskin, W. L. Chen, A. Vora

"This paper is concerned with the application of an abrasive waterjet for metal shaping. The waterjet cutting technology uses water compressed to the pressure up to 55,000 psia which is accelerated in a cylindric nozzle. Abrasive particles are then supplied into the water stream and accelerated by the water. Cutting occurs via the interaction between the water-particles stream and a workpiece that causes material erosion at the impingement zone. The mechanism of this interaction enables shaping of practically any material with a minimal effect on the metallurgy of subsurface. The motion of the jet penetrating through a material body is guided by a robotic arm. A waterjet cutter is becoming one of the principal tools for shaping titanium, super-alloys and other hard-to-machine metals and composites. The shaping, resulting from the waterjet cutter, is very similar to laser beam cutting. However, unlike laser processing, there is no damage to the subsurface structure.The presented work discusses the experimental study of cutting of titanium plates. The results of these experiments demonstrate the potential of the abrasive waterjet as a shaping tool. IntroductionOne of the main avenues in the development of metal shaping is the use of high energy beams as cutting tools (1,2). There are a number of advanced beam oriented material removal technologies, such as laser, electron beam, plasma and abrasive waterjet (AWJ) cutting. The advantages of AWJ cutting are well understood and documented (3-14). This technology has the potential of becoming the principal tool for netshaping and netsurfacing of parts. However, the use of AWJ is currently limited to cutting of hard-to-machine materials such as titanium, superalloys, glass, composites, etc. The cost of A W J cutting is much higher and the productivity is much lower than those of the thermal cutting. At the same time abrasive waterjet can be used for shaping any existing technological material from fabrics, plastics, aluminum to glass, composites, and diamonds. The material losses during AWJ shaping are minimal. The roughness and waveness of the surfaces generated during AWJ cutting are substantially less than those of the thermal cutting. Due to the size of the jet cross-section total force exerted by the jet on a workpiece does not exceed 30-50 newtons. This terminates the need in the use of complex fixture for material holding. Low applied forces and low surface temperature prevent the damage of metal subsurface in the course of cutting. The small size of the impingement area will determine the limited width of the kerf. Due to the size of kerf and unidirectional character of the water jet the formation of practically any metal contour is possible."

Jan 1, 1988