Search Documents

By Adrian J. Moore, Alan B. Richards, Rob Evans

Air and ground vibration from blasting is influenced by the delay pattern that is used. Wavefronts from blastholes fired in a blasting pattern can combine in certain circumstances to give increased blast vibration levels. A simple computer model has been developed which shows the combined effect of wavefronts from a multi-hole blast and identifies if wavefront reinforcement occurs, and permits delay patterns to be designed which will avoid or reduce wavefront reinforcement.

Jan 1, 1994

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

Blast vibration analysis under relatively near-field conditions has been carried out in a narrow-vein underground operation. The objective was to characterize the vibration signal (particle acceleration and velocity) from carefully controlled stope blasts. The limitations of such analysis in deriving design guidelines for reducing dilution has been elucidated. It has been shown that identification of each individual hole with specific explosive types can yield explosive-specific predictive equations for particle velocity. This has been coupled with measurement of actual overbreak to arrive at a limiting vibration level to generate a realistic design tool for controlling dilution in narrow-vein mines.

Jan 1, 2003

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Willard P. Ward

SOME TIME in the year 1874 or 1875, I conceived the idea that spiegeleisen might be made -in a blast furnace from ores that were not carbonates, and which did not contain both manganese and iron in the same ore. Up to this time, such ores had formed the basis of all the spiegel that had been produced; and all the ferromanganese that was on the market before 1875 was made in crucibles, and cost about 00 per ton, for 80 per cent. Mn. I consulted the great steel metallurgist of the day, Alexander Holley, who listened attentively to what I had to say, and told me he did not think my plan was practical, so I abandoned it for the time being. But I was so stubborn that I could not get the notion out of my head. It seemed to me that a good metallurgist should be able to work the thing out in some way. I had already had some experience in smelting refractory lead ores in Utah, and was young and not lacking in self confidence, so after waiting a bit, I got Anton Eilers, the best all-around metallurgist I knew, and J. H. Bramwell, the best iron blast-furnace man I knew, both intimate friends of -mine, to come to my place in Bartow County, Georgia, and look over things. They remained for several days, and made all the examination they thought necessary; and they also advised me to give up the project, and either to keep the furnace running on car-wheel iron or to blow it out. After my talk with Holley, I improved my plant in several ways. I closed the top of the furnace, put in a hot-blast stove, a steam boiler and a Weimer blowing-engine which gave me blast enough, at a pressure high enough for all the requirements of, the furnace, and which I could bring up to a temperature of 600° to 700° F.

Jan 1, 1921

By C. C. Furnas

IT is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investigations1 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper.

Jan 1, 1929

By Ralph H. Sweetser

IN these days of the almost exclusive use of byproduct coke as the blast-furnace fuel in this country, it may seem out of place, and smacking too much of reminiscing, to say anything about the use of anthracite coal for blast-furnace fuel. Viewed in the light of present day research and of developments in alloy steel, some observations seem appropriate regarding this raw material that played such an important part in the development of the iron and steel industry during 50 years of the past century. The research work of that period, in which the whole iron and steel industry was revolutionized, passing from wrought iron to steel and from charcoal to three new mineral fuels for blast furnaces, was done chiefly in the full-sized plants of that day; and it was done largely by the ironmasters themselves. The laboratory had not become a part of the ironworks, and scientific instruments were lacking around the blast furnaces; "rule o' thumb" and erroneous theories prevailed-and have not yet all been eliminated. The recent interest in meteoric iron in connection with nickel steels and other alloys proves that it is worth while to search for the reasons for excellence and the causes for failures in the metallurgy of bygone days. Turner1 gives the reasons why the blast furnace of Dr. F. W. Geissenhainer on Silver Creek, Schuylkill County, Pennsylvania, about 10 miles northeast of Pottsville, was operated successfully with anthracite2 in August and September, 1836, and why several other attempts failed. It has taken a long time for us to find out that there are great differences in the behavior of anthracites from the several parts of the anthracite region, as well as differences in coking coals from the bituminous fields.

Jan 1, 1935

By Ralph Sweetser

IN these days of the almost exclusive use of byproduct coke as the blast-furnace fuel in this country, it may seem out of place, and smacking too much of reminiscing, to say anything about the use of anthracite coal for blast-furnace fuel. Viewed in the light of present day research and of developments in alloy steel, some observations seem appropri-ate regarding this raw material that played such an important part in the development of the iron and steel industry during 50 years of the past century. The research work of that period, in which the whole iron and steel industry was revolutionized, passing from wrought iron to steel and from charcoal to three new mineral fuels for blast furnaces, was done chiefly in the full-sized plants of that day; and it was done largely by the ironmasters themselves. The laboratory had not become a part of the ironworks, and scientific instruments were lacking around the blast fur-naces; "rule o' thumb" and erroneous theories prevailed-and have not yet all been eliminated. The recent interest in meteoric iron in connec-tion with nickel steels and other alloys proves that it is worth while to search for the reasons for excellence and the causes for failures in the metallurgy of bygone days. Turner1 gives the reasons why the blast furnace of Dr. F. W. Geissen-hainer on Silver Creek, Schuylkill County, Pennsylvania, about 10 miles northeast of Pottsville, was operated successfully with anthracite2 in August and September, 1836, and why several other attempts failed. It has taken a long time for us to find out that there are great differences in the behavior of anthracites from the several parts of the anthracite region, as well as differences in coking coals from the bituminous fields.

Jan 1, 1935

By Carlo Massa

THE Societá Auonima di Miniere e di Alti Fourni, familiarly known as the " Elba Company," works the rich ore-deposits of the Island of Elba under a long-term contract with the Italian Government. The ore-deposits are scattered over the eastern and southeastern coast; but as those parts of the island are not well provided with ports, the blast-furnaces were built at Portoferraio, the principal town of the island, situated on the northern shore, and possessing a magnificent natural harbor where even vessels as large as the battleships of the Italian navy can comfortably anchor. In the selection of Portoferraio. the cost of transporting the iron-ore from the different mines to the blast-furnaces has been reduced to a minimum, and shelter has been provided for the Company's flotilla of tugs and barges, as well as for the steamers carrying coal and pig-iron. The whole plant, of which a general view is given in Fig. 1, comprises 1. A discharging-pier with unloading-cranes. The ore and coal are transported from this pier by means of an aerial cable-rail¬way to the coal- and ore-storage yards. This cable-railway is supported by an iron bridge extending from the pier to the shore and by a wooden trestle extending from the shore to the yards. , 2. Blast furnaces, two in number, with all the accessory appa¬ratus, such as blowing-engines, dry purifiers, Cowper hot-blast stoves, hoists, etc. 3. Coke-ovens, two batteries, with coal-bin, crushers and boilers. 4. Engine-house containing the blast-engines and the electric generating-station. 5. Pumping-plant. 6. Narrow-gauge railways.

Mar 1, 1905

By Chas. B. Dudley

A Discussion of the papers of Mr. James Gayley, on "The Application of the Dry-Air Blast to the Manufacture of Iron," and of Mr. J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," by Messrs. Charles B. Dudley, R. W. Raymond, J. E. Johnson, Jr., William F. Mattes, James Gayley, David Baker, John Birkinbine and F. E. Bachman. (Washington Meeting, May, 1905.) CHAS. B. DUDLEY, Altoona, Pa.:-Pam not a blast-furnace man, and this always puts me it a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, " I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of water-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 18S5, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are for the moment interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satis¬factory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much simpler way, simply saturate the air at a constant temperature, and thus get uniform working and

Sep 1, 1905

J. S. Unger,* Pittsburgh, Pa. (written discussion?).-I heartily agree with the author's suggestion, near the close of the paper, that greater uniformity in the making and use of brick is desirable. The effect of the manner of laying the brick, the mortar or cement used, the necessity of standardizing the shapes, the elimination of irregular or poorly designed brick, and the necessity for uniform operating conditions were pointed out by me some years ago. Many factors influence the quality of firebricks. The following figures obtained from bricks during their making or after completion show the need for greater uniformity in their quality. These results were obtained from regular commercial bricks, shipped to the consumer. In many cases the samples were from the same car load.

Jan 11, 1919

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By J. J. Bodmer

ALTHOUGH the similarity between puzzolana, or trass, and blast-furnace slag, as seen by comparison of the analyses, is a well-known fact, blast-furnace slag has not been used commercially as a substitute for those cementing materials. The reason, the writer apprehends, lies in the fact that unless such slag is disintegrated or subdivided by rolls, the process must either be too costly, or the material is not in a fit and proper condition for the purpose. In order to produce a reliable slag cement, the slag must be ground together with the lime into an impalpable powder. The subdivided slag must, therefore, be perfectly dry, and, at the same time, friable. The stronger the hydraulic properties of the lime, the more reliable the slag cement will be, and practice has proved, that the slag from a gray-iron furnace gives the best results. The slag cement which has given the results shown in the annexed table, under pressure tests, was composed of six parts of slag, from a blast-furnace producing No. 3 foundry iron, and one part of lime, of medium hydraulic properties. The above-described class of cement bears storing as long as most Portland cements, and the cheapness of its production is self-evident.

Jan 1, 1874

By Julian Kennedy Edgar

THINKING that it may prove of interest to the Institute, I have prepared a short account of the blowing in and subsequent working of the "A" furnace of the Edgar Thomson Steel Works. This furnace was built for the purpose of making spiegel, but has been started and is now running on Bessemer iron. The shape and size of the furnace are shown in the accompanying drawing. It will be seen that the section is formed of lines making very small angles with each other. In fact, an arc of a circle can be drawn, from the top to the tuyeres, which will nowhere deviate more than two inches from the lines given. In building, also, great pains were taken to gradually round the angles, so that the most careful observer, standing in the crucible and looking upward, could not tell at what points the slopes changed. It will also be seen that the widest part of the furnace is almost exactly midway between the bottom and the stock line, The flattest slope is maintained for 20 feet above the crucible, and is about 1 s inch to the foot from the perpendicular. The furnace is lined with small brick throughout, and has six tuyeres four inches in diameter, which project seven inches inside of crucible. There are three Siemens-Cowper-Cochrane stoves, each 15 feet in diameter by 50 feet high. Blast is furnished by an upright engine with 32-inch steam cylinder, 84-inch air cylinder, and 48-inch stroke. The steam cylinder has balanced poppet valves, working horizontally. The steam valves are worked by a Porter link-movement in order to obtain a variable cut-off. The exhaust valves are worked by a separate eccentric. It is intended to attach a governor to the cut-off, but at present it is set by hand. The steam cylinder is

Jan 1, 1880

By G. M. Proudfoot

IN June, 1940, a .Longyear 3420 blast-hole drill rig was purchased by the Hudson Bay Mining and Smelting Company for the purpose of experimental blast-hole drilling. The early work showed that the diamond drill could compete successfully with the Leyners then in use and by January 1st, 1941, the diamond drills were placed on contract. They may be considered to have gone into production at that date. Prior to the introduction of the diamond drill, our bench drilling was clone with Ingersoll-Rand S-70 and S-83 Leyner drills. Holes up to 40 feet were drilled, using coupled 1 1/4-inch round steel. Bits with a gauge of 3 inches were used in starting these holes, with a drop of 1/8-inch gauge for each 2-foot run. The holes normally ended with 1 1/2 or 1 5/8-inch gauge, though bits down to 1 1/8 inches were available for holes longer than normal or for holes drilled in abnormally abrasive ground. This method of drilling was very satisfactory and was a distinct improvement on the three-bench method of drilling used previously (1). During 1937 and 1938, when experienced miners were available, Leyner long-hole drilling was carried on with great efficiency. However, in 1939 and 1940, labour turnover in-creased and experienced long-hole drillers became scarcer. This resulted in a marked decline in the efficiency of the drilling operations, with increased costs and less tonnage drilled per shift. EXPERIMENTAL WORK The initial diamond drilling test work was carried on with a Longyear 3420 air-driven blast-hole drill rig, drilling a 1 3/16-inch hole. Tests indicated that diamond drilling could be successfully adapted to local conditions and that overall costs compared favourably with costs obtained with the Leyner long-hole method. Leyner long holes on stope benches usually bottomed at a larger diameter than the 1 3/16 -inch diamond-drill holes. More powder could therefore be introduced into the Leyner holes than could be placed in the diamond-drill holes. To achieve the same fragmentation, additional footage was required when diamond drilling. Diamond-drill holes of larger diameter were indicated.

Jan 1, 1943

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

By K. M. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 m (1 MPa, tensile strength) into the rock mass, a distance that is sufficient to have an impact on the pitscale slope over the long term. In addition, the damage zone was calculated using the assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone — up to 2.2 m (43 MPa, rock mass compressive strength) — indicates that microfracturing can occur throughout 20-50% of the entire rock mass in the blasting area, depending on the blast geometry, burden and spacing. Finally, an economic analysis was conducted by comparing two assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond’s law after increasing the blast energy from 180 kcal/t to 350 kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. However, the benefits of blast-induced microfracturing must be balanced against the potential impacts to slope stability to ensure safe conditions, a top priority in mining operations.

Jan 1, 2014

By K. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 meters (1MPa, tensile strength) in the rock mass, a distance that is sufficient to impact the pit-scale slope over the long term. In addition, the damage zone was calculated using the reasonable assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone ? up to 5.6 meters (30MPa, 30% of the compressive strength) ? indicates that microfracturing can occur throughout the entire rock mass in the blasting area. Finally, an economic analysis was conducted by comparing two reasonably assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond?s law after increasing the blast energy from 180kcal/t to 350kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. An optimal blast design should consider both slope stability (safety) and downstream comminution energy (production).

Feb 23, 2014

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.