Search Documents

E.T. CONNER;. Scranton;. Pa-I had the honor of being associated with Mid. Griffith in an investigation of the Scranton mine cave problem several years ago; in the course of which we investigated rather carefully the bearing strength of various materials that might be utilized for, the support of over We found that there were no reliable data as to the resisting strength, for instance, of gob pillars or timber cogs or cribs, nor as to the amount of compression that might be expected under a given burden. We made a series of tests at the Fritz engineering laboratory of Lehigh University, from which we, reduced certain conclusions, subject, however, to further test before they could be definitely recommended. Onr study of the subject was later checked by a commission appointed by the Governor of the State of Pennsylvania, to investigate the same subject the subsidence of the surface, and the danger entailed thereby. The State, commission made a series of tests on a much more ambitious scale at Pittsburgh, in the laboratory of the U. S. Bureau of Mines, and their tests agreed quite closely with those that Mr. Griffith and I had made. As the result of our study, we determined that the most elastic support is the ordinary timber cog or crib, while the most rigid support is a

Jan 1, 1918

By H. A. Bedworth

ALLOYS of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry1 proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche3 and Corson.4 The constitution of the system has also been recently investigated by Matuyama,5 and in the laboratories of the American Brass Co. by Smith.6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of, the constitution of copper-silicon alloys, the solubility reaches its maximum value, 6.7 per cent. silicon, between 721° and 782° C. At 852° C. the solubility is 5.25 per cent., while at 400° C. it is only 4.1 percent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent. silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By G. B. Misra

Though installations of main mine fans vary widely, the commonest installation is of a surface exhaust fan connected to an upcast shaft some distance below its collar by a horizontal fan drift bending sharply. downwards near its junction with the shaft. The junction of the fan drift with the shaft often causes considerable shock pressure loss if not properly designed. In one of the major coal mines in India circulating 180 m3/s of air through the mine a pressure drop of 229 Pa out of the total fan pressure of 568 Pa occurred at this junction while in a smaller gold mine circulating 9.4 m3/s it was 147 Pa out of a fan-drift pressure of 382 Pa. With larger mines circulating larger volumes of air, ill designed fan drifts can lead to considerable wastage of the power of ventilation. Shock loss at the junction of fan drifts with exhaust shafts depends on (1) the angle of deflection of the bend, (2) sharpness of the corners (both inner and outer) at the junction, (3) the degree of contraction of the flow-stream which depends on the cross- sectional area ratio of the shaft and the fan drift as well as the amount of leakage through the shaft collar. It must be noted here that the friction pressure loss in the bend is negligible compared to the shock pressure loss.

Jan 1, 1980

By T. L. Joseph

THE United States Bureau of Mines has been studying the blast-furnace process for, about ten years. An experimental furnace was developed by the bureau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.1 Royster, Joseph and Kinney§(48) found that the particle size of ore had an important effect upon the blast-furnace, process. Kinney(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of the stock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or . formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust.

Jan 1, 1930

By N. A. Ziegler

A CERTAIN amount of interest has been indicated recently in the resistance to oxidation at high temperatures of iron-aluminum alloys (rich in iron). Hautman1 published a paper in which some interesting results are given. According to his paper, only alloys containing at least 8 per cent aluminum indicate a marked improvement in their resistance to oxidation. At about this aluminum content, however, alloys become brittle, which considerably reduces their commercial value. About two years ago the author performed a series of experiments, the results of which are presented here. A series of iron-aluminum-carbon alloys was prepared by melting electrolytic iron, aluminum and high-carbon iron alloy in an induction vacuum furnace.2 The list of these alloys is given in Table 1. Each alloy was forged in the ordinary way to

Jan 1, 1932

By N. A. Ziegler

A CERTAIN amount of interest has been indicated recently in the resistance to oxidation at high temperatures of iron-aluminum alloys (rich in iron). Hautman1 published a paper in. which some interesting results are given. According to his paper, only alloys containing at least 8 per cent aluminum indicate a marked improvement in their resistance to oxidation. At about this aluminum content, however, alloys become brittle, which considerably reduces their commercial value. About two years ago the author, performed a series of experiments, the results of which are presented here. A series of iron-aluminum-carbon alloys was prepared by melting electrolytic iron, aluminum and high-carbon iron alloy in an induction vacuum furnace.2 The list of these alloys is given in Table 1. Each alloy was forged in the ordinary way to

Jan 1, 1932

By Norman Pilling

THE solubilities of a series of experimental alloys covering the range 0 to 100 per cent. Ni, 0 to 30 per cent. Cr have been studied under conditions of complete submersion in several fully aerated acid solutions, and in solutions containing sulfurous acid. In nonoxidizing, hydrogen-discharging acids, if the nickel content is below a certain critical amount, chromium increases the rate of solution and nickel decreases this rate; this critical content of nickel is about 13 per cent. Alloys containing more than this corrode at a constant minimum rate independent of iron, nickel or chromium contents. Austenitic chrome-nickel steels may thus have a resistance to these acids equal to that of nickel-chromium alloys. In nitric acid and in unaerated sulfurous acid rather sharp limits of attack occur which are principally dependent on chromium content. In the former the limit of attack is not related to a particular chromium content but varies continuously with acid concentration. The action of sulfurous acid on these alloys is highly dependent on the presence of small amounts of other substances in solution, and many sulfurous acid mixtures rapidly attack alloys to which the pure acid is wholly inert. The observed effects are. not compatible with Tammann's theory relating corrosion resistance to lattice structure but are believed to be concordant with current views of the electrochemical nature of corrosion.

Jan 1, 1929

By D. O’Connor, A. Pytlik, D. J. Corbett

The resistance of yielding rockbolts to multiple impact loads was tested by means of a drop hammer. The methodology was based on the ASTM D7401-08 standard as well as the requirements specified for rockbolts by Luossavaara-Kiirunavaara Aktiebolag (LKAB – a Swedish mining company) and the Safety In Mines Research Advisory Committee of South Africa (project number GAP 423). During the tests, the loading force and bolt elongation were measured with a sampling frequency of fs = 19.2 kHz. In order to analyse the phenomena involved, the tests were recorded using two independent high-speed video cameras (600 and 1000 frames per second) and one thermal camera (128 frames per second). The tests demonstrated that all the samples transferred double the gravitational potential energy of Ep = 50.85 kJ from the impact load of mass m = 2825 kg and impact velocity of v = 6.0 m/s without failure. Damage to the bolt-resin contact in the upper anchoring zone of the bolt in the steel tube occurred after subsequent impacts. As a result, the macro-deformed bolt exhibits additional yield, and its operation following the shearing of the resin bond is similar to that of a ‘cone bolt’. Only one test resulted in damage to the threaded bolt rod-nut coupling, during the fourth impact; however, no damage to the bolt-resin contact zone was observed.

Nov 6, 2023

By R. C. Nkhoma, K. A. Annan, S. Ngomane

The effects of welding current, electrode force, and welding time in a resistance spot weld were studied to investigate the effectiveness of welded joints between a thin EN10130: DC04 material and a thicker 817M40 part, through analysis of the microstructural and mechanical properties. All welded specimens were subjected to tensile testing at room temperature (25°C) and sub-zero temperature (–46°C) to test the strength of the welded joints. No full button failure was observed at either room temperature or sub-zero temperature after optimization of the weldng parameters. The fusion zone was observed to consist mainly of martensitic phase, due to rapid quenching, while the HAZ was composed of clusters of martensite in a ferrite and bainite matrix. The base 817M40 metal remained fully ferritic after welding. The hardness was found to increase with increasing welding current. An increase in nugget size, indicating good fusion of the weld, was observed with an increase in the welding current.

Oct 1, 2021

By F. W. Robinson

THE temperature coefficient of electrical resistance of pure metals is high and therefore the resistance increases rapidly with rising temperature. In 1871, Siemens suggested the use of this property as an accurate means of temperature determination. Owing to practical difficulties, particularly the contamination of the metal and consequent permanent change in its resistance and its resistance-temperature relation, this method fell into disrepute as a practical standard until revived later by Callendar and Griffiths, and subsequently by Holborn and Wien, all of whom showed that the earlier difficulties were not inherent in the method but incident to the mode of protection of the resistance coils. Following .the work of these investigators, the problem of temperature measurement by this means has been the subject of careful study and has now assumed an importance second only in practical adoption to the thermo-electric method. It is generally recognized, both here and in Europe, that the standard temperature scale should be the thermodynamic as it permits the evaluation of high temperatures on the basis of the radiation laws of Stefan and Bolzmann, of Rayleigh, and of Wien and Planck, on a scale consistent with that obtained by means of the gas thermometer at low temperatures. Lord Kelvin showed that only. a very small correction, amounting to about +0.7° at 1000° C.-almost within the limits of experimental errors-is necessary to adjust the constant-volume nitrogen thermometer to the ideal thermodynamic scale.

Jan 9, 1919

By Charles Frey

TIE fundamental principle of resistance thermometry lies in the determination of temperatures by the measurement of an electrical conductor subjected to various temperatures and the translation of the resultant changes, in ohms, into temperature equivalents. Such resistance measurements can be made with maximum precision by the use of a standard Wheatstone bridge and a reflecting galvanometer of high sensitivity. Under such conditions, results are obtainable that may be accurate within 0.1 or even 0.01 per cent., and the "idiosyncrasies" of heated electrical conductors can be studied with advantage and profit, even if the latter is not of a financial nature. The chief requisites for producing a serviceable -commercial instrument may be enumerated as follows: First, there must be a resistor or "bulb" that can stand the maximum temperature without deterioration and which has a pronounced temperature coefficient. Second, there should be constructed an "even" bridge, having two fixed arms of equal values, in ohms. Third, a rheostat, the maximum resistance of which will be equal to the total change in the resistance of the bulb, between temperature extremes, is required. Fourth, there must be a sensitive galvanometer which is aperiodic, or nearly so. Finally, there should be a fairly steady source of direct current. The general scheme of this type of apparatus, in its simplest form, can be readily understood by reference to Fig. 1. Resistors A and B are constructed of manganin, therlo, or some other resistance wire having a negligible temperature coefficient. The sensitive D'Arsonval galvanometer G has its zero in the center. R is a rheostat and X is a resistor or bulb made of insulated platinum wire, or else of nickel, copper, or some alloy, according to requirements. K is a battery, but a direct-current service line is often used instead, with sufficient ballast in series to properly reduce the current.

Jan 8, 1919

G. A. ROUSH,* South Bethlehem, Pa. (written discussion?).-Mr. Frey is correct in his impression that ice floats, but "frazil" ice happens to be the exception to the rule. The requirements for the formation of

Jan 12, 1919

We live in a world in crisis. One where the tides of change run ever faster. Where the only thing we can be sure of is change itself. The challenge we face, therefore, is not how to resist the forces that move us nor even to try to predict where they will lead us, but to harness their energy and use their momentum to find new and innovative solutions to problems that can seem intractable. Indeed, crisis is often the catalyst which energises a business to change its technology and to form a partnership with a company which specialises in pioneering new technology.

Jan 1, 1993

By A. Yousefpour, M. Hojjati, M. Simard, M. Laramée, M-A. Octeau

The need for effective and reliable joining methods grows as the use of advanced thermoplastic composites becomes widespread in aerospace industry. An experimental investigation of resistance welding of APC-2/AS4 thermoplastic composite laminates is presented. In this method, a heating element is placed between the bond-surfaces then the interface is heated by passing electrical current through the heating element. The polymer at the weld interface is melted due to resistance heating, then diffuses and consolidates under applied pressure, resulting in a weld. APC-2/AS4 prepreg, APC-2/AS4 commingled, and different grades of metal mesh heating elements were considered. A custom made resistance welding rig was designed and developed to perform lap-shear welds. The mechanical performance of the welds was quantified using single lap shear tests. The effects of different heating elements on the mechanical performance of the resistance-welded parts were investigated. Also, quality of the welds was examined under optical microscopy.

Jan 1, 2004

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

A new least-squares method for inversion of d.c. resistivity soundings from horizontally layered earth is proposed. Powers are used as measured data. Apparent resistivity is generalized and apparent parameters curves are defined. Estimates for parameter errors are often possible even when data errors are unknown or large. Acceptance or rejection of a model is made an easier decision. Total computational effort is often reduced when compared to global least-squares methods, because although several optimizations are needed, few data points are involved in each, and initial guesses are requested only once and not all at the same time. Correlations between parameters may be used to improve solutions. Precise indications for extra needed data points can be conveyed. A test example is worked out and a field sounding, taken by Rijo (1973, personal communication) in an alluvium-filled river valley in north-eastern Brazil, is studied.

Jan 1, 1987

By Omnes G

Sixty Schlumberger electrical soundings were carried out in the Depot Springs area, near Agnew, Western Australia as part of an investigation into the availability of groundwater for the Agnew nickel project. The object of the survey was to locate calcrete aquifers related to Tertiary drainage channels on the Pre- Cambrian surface. The electrical soundings were initially interpreted using sets of master curves and auxiliary point methods. Electrical sections were produced and contour maps prepared of apparent resistivity for AB=80m, total conductance of the overburden and transverse resistance.

Jan 1, 1975

By Vitor Luiz Sordi, Gustavo Henrique Pelissari

O AISI201LN é um aço inoxidável austenítico com teor reduzido de Ni em relação aos tradicionais da série 300 e com adições de Mn e N como estabilizadores da austenita. Os aços da série 200 se propõem a substituir outros inoxidáveis em algumas aplicações com vantagem econômica pela redução do Ni, porém há pouca informação sobre o seu comportamento em temperaturas elevadas. Este trabalho avalia a resistência à tração do AISI 201LN na temperatura ambiente e na faixa de 500ºC a 800ºC e a resistência à fluência na temperatura de 700ºC. Observou-se que, comparado a outros inoxidáveis austeníticos, o material estudado tem resistência à tração comparável em temperatura ambiente e mantem boa relação ductilidade – resistência no intervalo de 500ºC a 800ºC. O aço AISI201LN apresentou desempenho em testes de fluência na temperatura de 700oC comparável ao de outros aços inoxidáveis austeníticos largamente utilizados para aplicações em altas temperatura, incentivando assim a ampliação dos estudos em outros intervalos de tensões e temperaturas.

Oct 21, 2019

By Luís Carlos da Silva

Vários motivos levaram a priorizarem o uso de fibras naturais em detrimento do uso de fibras sintéticas, sobretudo as razões sociais e ambientais. A fibra deste trabalho é extraída da folha da planta - Furcraea Andina (da Colômbia, onde usam esta fibra para a produção de artesanatos e sacos) e demonstra um grande potencial como reforço de compósitos poliméricos. Este trabalho avaliará o teste de impacto de Izod e Charpy de compósitos com matriz epóxi reforçada com diferentes porcentagens de fibras. Para os testes, as fibras de fique foram misturadas com à resina epóxi em um molde metálico retangular, o conjunto foi submetido a uma pressão e sofreram um processo de cura à temperatura ambiente durante 24 horas. As amostras produzidas foram submetidas aos ensaios seguindo a norma ASTM D256 (Método de Ensaio Padrão para à Determinação da Resistência ao Impacto do Pêndulo Izod para Plásticos) e a norma ASTM D6110 (Método de Ensaio Padrão para Determinar a Resistência ao Impacto Charpy para Plásticos). Os compósitos continham até 30% em volume de fibras de fique, que foram alinhadas ao longo de todo o comprimento da matriz. As amostras submetidas à ambos os ensaios (Izod e Charpy) tiveram suas fraturas analisadas por microscopia eletrônica de varredura (MEV). Houve um aumento significativo da resistência ao impacto de acordo com o aumento da porcentagem volumétrica das fibras de fique. Esse desempenho pode estar associado ao mecanismo de fratura gerado a partir da adesão entre as fibra de fique e a matriz colaborando na absorção da energia de impacto, além do fato de que a fibra é capaz de dificultar a ruptura das amostras.

Oct 30, 2017

By Caroline Gomes de Oliveira

Os impactos causados pela exploração dos recursos naturais pelo homem geram uma crescente inquietação em relação futuro do planeta a longo prazo. Assim, as fibras naturais vegetais ganham destaque como material de reforço por suas boas propriedades mecânicas, baixo custo e por serem biodegradáveis. Umas das fibras que mais ganhou destaque nas últimas décadas é a fibra de rami, objeto de inúmeros estudos. Neste trabalho, analisou-se o efeitodo tecido produzido com a fibra de rami como reforço para a matriz epóxi sob esforços de impacto Charpy e Izod. A metodologia utilizada foi a produção de placas laminadas sob afeito de vácuo. Os resultados mostram notável diferença na resistência ao impacto do compósito comparado à matriz sem reforço.

Oct 30, 2017