Search Documents

[Module 10. Internally Cued Operating Contingencies Prerequisite: Modules 1-7 - Estimated Instructional Time: 2.42 hrs. Module Abstract Trainees, using programmed instruction, describe the cues, consequences, operational sequences, and possible causes resulting from loss of air pressure from power fluctuations, and from a failure of the automatic lubrication system. Although some of the contingencies may be initially signaled by an alarm or from the oiler, each trainee will demonstrate proficiency in the appropriate operating techniques and procedures. This module also includes a review component for those trainees identified in the assessment exam as requiring less detailed instruction.]

Jan 1, 1976

By Kent W. Hawley

An improved visibility system was developed for use on the large (100 ton+) haulage trucks typically operated in open pit and surface mines. The improved visibility system provides the truck driver' with a means of viewing hazardous situations that occur in the extensive blind areas adjacent to his true. The cost effective, reliable, visibility system consists of a closed-circuit television three unique fresnel viewers, and two improved mirrors. This report describes the visibility problems of Large trucks in the surface mining environment, shows the performance of existing mirrors, substantiates concept selection, and describes the prototype improved visibility system.

Jan 1, 1978

By John L. Dahle

This report documents the research efforts that were undertaken to design, install and test noise abatement devices for use on off-highway haul trucks operating in surface mines. The objective of the program was to reduce the environmental noise from haul trucks. The noise reduction devices that were developed utilized existing technology and were tested on a 50-ton haul truck. The efforts emphasized the reduction of noise emitted from the engine compartment which included the use of side shields, sound absorbing material, improved radiator shroud design, and a modulating clutch fan. Noise tests were conducted using modified SAE test procedures for measuring sound levels around a stationary and moving machine, and inside of the operators compartment. Test results showed a maximum of 4 dB(A) reduction measured 16 feet from the truck. Interior cab noise was reduced 6 dB(A) with the windows and vents closed.

Jan 1, 1983

By Wils L. Cooley

Several aspects of mine safety grounding systems and equipment are studied. Electrolytic corrosion of test ground beds has shown a high incidence of stray current damage, while efforts to build a reliable continuous ground bed monitor continue. Laboratory and field investigations of trailing cable splices have yielded strong evidence that splices can contribute to stray current problems in the mines, but a method is suggested for discovering deteriorating splices before they pose a serious hazard. A prototype device has been constructed to evaluate the electrical resistance of rail bonds underground as a source of stray current. Theoretical modeling of ground electrodes, has advanced considerably, now covering measurements of large cylindrical electrodes, multiple-rod ground beds, rod electrodes in stratified earth, and measurement of connected beds. A prototype instrument design is given for a potential gradient plotter to quickly evaluate voltage gradients near earth electrodes. Additional ground-check monitor testing is reported.

Jan 1, 1977

By Dennis R. Kasper

This study evaluates selective environmental impacts of two distinct in situ mining techniques. In situ leaching of uranium, porphyry copper and native copper and in situ borehole (slurry) mining of uranium, sandstone, and pebble phosphate ores are the techniques and minerals investigated. The potential impacts onsite in the desert southwest (porphyry copper), Michigan (native copper), Texas and Wyoming (uranium), and Florida and North Carolina (phosphate) are addressed and discussed. The study emphasizes those impacts which are unique to in situ solution leaching and borehole slurry mining. Impacts which are characteristic of all construction projects in the general geographical areas investigated, such as socioeconomic effects on surrounding communities and site-specific impacts, such as rare and endangered species, are beyond the scope of this study. For each of the in situ processes and associated ores investigated, the physical and chemical characteristics of the systems are described, the toxicity of the leaching solutions are presented, and the potential impacts on the environment are developed.

Jan 1, 1979

By GJ Hundman

The Multiple Unit Continuous Haulage (MUCH) System was designed to provide the capacity to continuously convey coal from the mining machine to the main haulage belt. The MUCH System has an operator who steers the lead vehicle, ever following the mining machine. All the remaining vehicles follow the path of the lead vehicle, with their conveyors automatically lining up between the lead vehicle and mine section panel belt. This is accomplished by mechanical linkages on the vehicles which are interconnected by steering bars between vehicles (patent pending). The MUCH System has an operator who steers the discharge vehicle when outby travel is required. Outby travel is just like inby, with each vehicle following the path of the preceding vehicle. Surface tests overwhelmingly indicate the "UCH System should track/retrack successfully in square pillar underground room and pillar coal mines with 18 ft. wide entries and slopes up to 10 percent. For 60 degree pillar plans the minimum entry width required is 15 ft. Surface tests also indicate the MUCH System will convey over 8 TPM of coal around 90 degree corners without excessive spillage.

Jan 1, 1983

Auger operations produced 14 million tons of coal in 1974, or approximately 5% of all surface mined coal. It was the most efficient of all coal mining methods, producing 40.0 tons per man-day. Exhibit 1.1 gives a breakdown of productivity of all coal mining methods. Exhibit 161 PRODUCTIVITY OF COAL MINING METHODS (Short tons per man-day) [Method - 1971 1972 1973 1974 Conventional 11.00 10.00 9.75 9.30 Continuous 13.00 12.50 12.25 11.90 Strip Mines 35.69 35.95 36.00 36.00 Auger Mines 39.00 43.00 45.33 40.00 ] Unlike other surface mining methods, augering produces clean coal, largely uncontaminated by foreign materials, other than those existing in the coal seam itself. However, compared to other methods, the coal recovery rate is relatively low. For example, a triple-headed auger in a 35-inch seam would recover approximately 50% of the coal in the seam as compared to a 90 to 95% recovery rate for strip mining and a 55 to 65% recovery rate for deep-mining. The low auger recovery rate is due to the circular cuts and pillars left in the seam.

Jan 1, 1975

By Paul J. Guay

This report presents the results of evaluating a longwall mining system specifically designed to extract a very deep web (60 inches or deeper) from a longwall panel. The report includes a productivity and cost analysis comparing the new mining sys-tem with a high capacity conventional longwall operation taking a 30-inch wide web. The analysis shows the new system will increase annual production 44 percent and decrease cost per ton off the face 21 percent. The report also includes conceptual drawings and specifications for a high capacity four-drum shearer and a unique shield type of roof support specifically designed for very wide web operation. The advantages and problems associated with wide web mining are discussed in general and as they relate specifically to the equipment selected for the new mining system. The study concludes by recommending that surface coal loading tests be conducted as the follow-on work.

Jan 1, 1978

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By F. S. Kendorski

This report presents the results of a search for viable-self-drilling roof bolt concepts, detailed development, design, and manufacture of such bolts that drill their own holes, and testing in the laboratory and in the field in two different coal mines of three self-drilling roof bolts. Three new types of bolts were designed and tested, which drill their own holes and then anchor in continuous operation. These were a spring-actuated mechanical expansion shell, a slot and wedge, and a self-contained resin anchor bolt. Such bolts when fully developed for mine use would allow safer and remote installation of ground support and increase productivity. Recommendations are given for further work to improve drilling and anchorage performance.

Jan 1, 1979

By F. J. Prokoski

The COALSTAR Project, which operated from November 1981 to December 1982, was a research and development project aimed at providing a reliable and inexpensive means of monitoring various waste site conditions via the GOES satellite system. The GOES system provides data transfer from unattended isolated sites where neither power nor telephone lines exist. The reliability and resolution of the data received while using the satellite link were excellent; however, the site instrumentation gave considerable trouble. The disastrous failure of a large coal waste embankment in 1972 led the Bureau of Mines to undertake a comprehensive program to reduce the likelihood of such an occurence again. Part of this program involved the installation of instruments to monitor the stability of a specially-selected embankment operated by Armco Incorporated near Montcoal, West Virginia. Initially, the instruments were monitored by normal telephone lines and used normal commercial power from the local utility. The project described here was initiated to replace this monitoring system with an unmanned, solar-powered data collection system which transmitted data via satellite to a central computer facility. The satellite data network is the National Earth Satellite Service of the National Oceanic and Atmospheric Administration.

Jan 1, 1984

By D. A. Paice

Direct current electrical systems are used in most coal mines primarily to power the main haulage trains and secondarily to feed other equipment and passageway lighting. Electrical power is supplied from rotary machines or static rectifier equipment and is distributed through the mine by open trolley wires and feeder cables. The rails of the haulageway are used as a current return path. This exposed power distribution system is very vulnerable to conditions which lead to undesired leakage currents and short circuits and, consequently, the possibility of fires or other hazards to personnel. Present techniques and equipment have been utilized in so far as practical to improve the safety of the dc electrical system; however, there still appears a need for further improvement. Because of this need, this program was sponsored by the Bureau of Mines to investigate two specific technical areas related to improvement of dc electrical system safety. One area included the determination of the characteristics of mine electrical systems and their protection requirements and the verification of the adequacy of available protective devices for mine service. Despite the widespread application of industrial protective equipment in mines, there was little detailed technical information available related specifically to the performance of this equipment in service. Our task was not only to develop useful information regarding mine system protection, but also to define and verify the adequacy of the protective devices available. The second area of investigation called for development of a practical technique for detecting low level electrical fault or leakage currents. Conventional protective devices

Jan 1, 2012

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine would be drilled. The geologic formations encountered in this hole are discussed. Correlation of the geologic horizons encountered in this hole with those encountered in nearby drill holes was accomplished by the use of geophysical logs. Data on the geophysical interpretations are provided. The anticipated geotechnical characteristics of the geologic units encountered in Pilot Hole "X" are described.

Jan 1, 1977

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining' the potential fur reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Michael L. Clar

The U.S. Bureau of Mines contracted a study to determine the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. All relevant published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines was reviewed and organized into a bibliography. The impacts of mine water with respect to health and safety, production, environment, and costs were assessed. Sources of water inflow into underground mines were described. A summary description and evaluation of techniques that can be used to reduce the amount of water entering underground coal mines was prepared. A review of engineering practices currently used by operating coal mines in the Appalachian region to prevent the movement of ground and surface water into active coal workings was conducted. Major emphasis was placed on the identification of the geologic and hydrologic con¬dition of the site, onsite inspection of the methods used and an evaluation of their technical and cost effectiveness.

Jan 1, 1981

By D. A. Paice

Under the first phase of this contract as reported in the Phase I report it was determined that certain types of commercially available molded case breakers are capable of interrupting mine dc power supplies of nominally 300 volts or 600 volts rating. These circuit breakers incorporate conventional overcurrent trip units but also can be operated by means of low power signals fed to a shunt trip coil. Further development in the Phase I program produced a means whereby a discriminating circuit breaker detector unit could sense the presence of illegitimate loads on the dc electrical system and cause the circuit breaker to trip. The detector unit operated by detecting the presence of 3000 Hz currents which were generated in the illegitimate loads by means of a 12 volt, 3000 Hz signal applied to the dc system. Further development of the program has continued in Phase II with the aim of verifying the practicability of the complete discriminating circuit breaker concept and developing other types of equipments required to implement a system. These other equipments include electronic means for raising the apparent impedance of high power legitimate loads and static filters for smaller loads. The results of laboratory work and limited underground tests have been successful. This report describes the system and the tests that have been conducted on the various equipments that comprise the complete Discriminating Circuit Breaker Concept.

Jan 1, 2012

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Michael L. Clar

This volume is an annotated bibliography of published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines. This literature was used to develop Volume 1 of this report, which assesses the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. Each abstract is followed by subject descriptors. the abstracts are listed alphabetically by title and are numbered consecutively. These numbers are used in the subject index to help the reader locate the appropriate articles.

Jan 1, 1981

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. The history of the drilling of Pilot Hole "XI' is presented. This historical summary provides the details of method used during the drilling of this hole. Problems encountered during drilling are discussed. The quantities of drilling mud and other materials used to drill the hole are documented.

Jan 1, 1977