Search Documents

By Ben Murphy, Alejandro Yanez, Tatu Miettinen

"Flotation using large volume cells has grown in importance during recent years, particularly given the increasing demand for minerals whilst ore grades are decreasing. Outotec introduced the TankCell® e300 in 2007 to enable concentrator plants to process these higher tonnages. From the beginning, TankCell® e300s with FloatForce® mixing mechanisms have demonstrated good metallurgical performance with decreased operating costs and high availability. This paper deals with specific engineering challenges that need to be considered when installing these units rather than giving examples of performance. Today there are over 100 TankCell® e300s operational worldwide. As more of these units are installed new technical challenges are encountered and solutions developed to maximize their productivity. Lessons have been learnt by operators, engineering companies and the cell manufacturers on how best to design and layout these cells in modern concentrators to ensure smooth transition from design to installation to operation. This paper presents information on important design considerations and learning that has been obtained through the design, installation and commissioning of the TankCell e300 around the world. Areas pertaining to cells layout such as feed and discharge arrangements along with items of metallurgical concern such as sampling, reagent addition and the potential benefits of installing a variable speed drive on the motor will be covered in depth."

Jan 1, 2014

By A. K. Fallaw, D. L. Taylor, G. Wang, L. R. Moore, S. Dobson, C. B. Parkinson

"Over the years, the decline of high grade ores have become an increasing problem in the global mining industry. As such, techniques and chemistries must change in order to continue to meet the market demand and quality. Reverse cationic flotation of quartz and silicates is one of the most important techniques for generating the industry standard product from minerals such as iron and phosphate ores. Amine collectors are the global standard in such processes. However, as the ore quality continues to decline so must the chemistry change to meet the change in ore composition. This paper will focus on the introduction and full scale application of a novel amine collector towards a cleaner flotation process in phosphate beneficiation with Crago process. The results suggests the collector is capable of improving the phosphate recovery, in this cleaner circuit, to approximately 94% with minimal sensitivity to the everyday changes in feed grade.INTRODUCTION The days of mining high grade minerals are long gone, but the demand continues to increase. Phosphate ore, for example, is most dominantly demanded from the agriculture industry as a fertilizer component (i.e. diammonium phosphate, DAP) (FAO, 2014). Some literature suggests that global food production must increase by approximately 70% by 2050 (Cordell, 2009). It is also suggested that the peak global phosphorus production will occur around the year 2033, which is the period at which the easily accessible reserves have been depleted. Currently, phosphorus is commonly mined with a BPL (Bone Phosphate of Lime) concentration of 12-20% and a remainder typically being gangue minerals such as silica, clays, metal oxides, calcareous minerals, and carbonaceous minerals. These gangue components can lead to various negative processing and utilization consequences. Calcium, from carbonaceous minerals, is problematic due to the elevated levels of sulfuric acid required to convert the phosphate rock to the acid form (SRI Consulting, 2009). Calcium can also lead to elevated dosages of flotation reagents due to the desire of the fatty acid to coordinate to calcium minerals. Carbonate leads to increased levels of foam during the wet acid process. Silica is associated with the level of insols (acid insolubles), which must be less than 10% in the final concentrate that will be transferred to the chemical plant for acidification. Phosphate ore can generally be classified as carbonaceous or siliceous (El-Shall, 2003). Siliceous ores are commonly processed through various sizing steps followed by multi-staged flotation (Figure 1) (FIPR, 2014 & Güven, 2010). Though the higher grade phosphate pebble is declining, many mines are still able to size good enough to produce some amount of such pebble. Unlike most metal flotation processes where grinding is a necessity for an optimal process, Florida phosphate flotation does not generally require aggressive grinding and can typically operate at 0.1-1.0 mm. The rougher flotation step applies pH modification to achieve the optimal pH of 8.8-9.3 followed by conditioning with a fatty acid type collector, which builds a hydrophobic waxy layer on the surface of the particle to assist in the flotation. This generally achieves higher than 85% recovery of a product with 50-60% BPL and 15-30% insols. Unfortunately, DAP production generally requires 3.5 tons of phosphate rock containing greater than 63% BPL to produce 1 ton of phosphoric acid (ArgusMedia, 2014). Thus, further purification is required to achieve the grade by the chemical plant for fertilizer production. After the fatty acid is scrubbed off the phosphate particles using sulfuric acid (pH 2.5-3.5), the pH is generally operationally readjusted to 6.5-7.2 by washing with “fresh” water. A second collector is applied prior to the cleaner, which is a reverse cationic flotation process. This collector is typically a cationic amine based reagent, which should have an affinity for silica containing mineral"

Jan 1, 2015

By J. C. Monette

Stripping of gold and silver from carbon is effected by means of two main processes (AARL and ZADRA ). The main rate-enhancing parameter in the stripping of gold and silver is temperature. A secondary rate-enhancing parameter is ionic strength. (1) Stripping is usually conducted within a solution containing sodium cyanide (0.1 -0.5% ) and caustic ( 1 -3%). The development of a chemistry that increases the rate of gold and silver stripping from carbon in a manner proportional to its concentration is described. Its use in atmospheric and pressure strips is also outlined.

Jan 1, 1992

By Sir Robert Hadfield

(New York Meeting, February, 1913.) THE Hadfield method of producing sound steel ingots has been the subject of a paper 1 read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make possible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying additional beat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By-one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molted condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 4, 1913

By Larry S. Diaz

The paper considers the selection of control instrumentation for a modern flotation plant, as well as the best interpretation and most effective use of the process data obtained. Process control computer availability is considered from the outset. A general philosophy of control is proposed which leads toward a system that is its own reliability monitor. The bulk of the problems are in grinding and classification. Alternative control methods are described that use particle size measuring devices. Flotation controls, based to a large extent upon on-stream X-ray analysis, are reviewed in detail. Reagent control methods are also examined. Methods to analyze the data obtained from the various measurement devices are introduced. These methods would enable an estimate of the validity of the data and require some redundant information. Another objective of these methods is the protection of operating equipment from possible control malfunctions. Although the discussion generally considers some degree of computer usage, this paper attempts to describe instrumentation and data analysis methods that enable control with or without the process control computer.

Jan 1, 1972

By Jeffrey T. McGinty, Frank M. Wheeler

Plant layout is the arrangement of equipment, process areas, departments, infrastructure, and support facilities. Plant logistics is the flow of parts, people, resources, and information throughout the production process. This chapter: outlines key factors and provides checklists to facilitate layout development; presents risk management approaches to test the logistics and functionality of alternative layouts; and uses real-world examples to illustrate effective simulation modelling to assess plant layouts.

Jan 1, 2015

By J. A. MacLellan

It is the hope of the author that this paper, largely a compilation of observations and opinions built up over 20 years of experience in cold and remote areas may be of some help to others in designing better plants for the future in the north. The north is not as difficult to operate in as the better story tellers make it appear to be. ()n the other hand for 6 months of the year the cold is always there, and it seems to be waiting for someone to make a mistake. The simplest things can shut a multi-million dollar plant down at -4n' F with a 4n M.P.H, wind. It only takes one man door improperly latched to freeze up all the pumps on the bottom floor. Someone can poke a one inch hole in an outside wall in July and six months later while you are having Christmas dinner, a watchman will call up to report that the whole plant is flooded because the main water line just froze up and burst. Basic things to remember in plant design for cold and remote areas are: everything in these areas is more expensive due to long and difficult supply lines. Fuel is expensive and would be a major cost item even if it were not expensive, due to the extended periods of low temperatures. Building volumes should therefore he kept to an acceptable minimum. Service areas on the other hand must he adequate, because maintenance generally has to be conducted inside in a heated area. Supply vehicles for instance have to get completely inside the building to unload. If you try to unload a supply vehicle with the door open at -50° F, you won't be able to find the vehicle for fog and if you take more than 5 minutes half the water lines in the plant will freeze up. People in a remote area are expensive. The capital investment per employee may be as high as $30,000; with fringe benefits per annum costs of an employee will he as high as 812,000 per year regardless of basic wage rate. It

Jan 1, 1971

By J. S. Johnson, W. C. McCulloch

ALL phases of plant operation must be synchronized so that the number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shutdown. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow. ORGANIZATION Probably the most important item for successful operation of a preparation plant is a capable organization interconnected with the mine organization. A typical organization chart for companies operating in the Pennsylvania anthracite region is shown in Fig. 1. The breaker foreman is in direct contact with the plant preparation operation and reports to the outside foreman, who, in turn, reports to

Jan 1, 1943

By J. S. Johnson, W. C. McCulloch

All phases of plant operation must be synchronized so that the A number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units, parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shut- down. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow.

Jan 1, 1943

By J. H. Fourie

This paper highlights modern practices in ore-treatment plants, with particular reference to the flotation of P2O5 at the plants of the Phosphate Development Corporation (Foskor) at Phalaborwa in the northern Transvaal. The following aspects are covered: design criteria, equipment and personnel, production standards and control. cost control, maintenance, and process development.

Jan 1, 1981

By Michael A. Eamon

Magma Copper Company has operated its San Manuel SX-EW Plant facilities since 1986. The original plant facilities have a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solutions from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing leach solutions from an insitu leaching operation. This paper presents a general overview of plant practices with particular emphasis on process innovations developed and implemented by Magma during construction and operation.

Jan 1, 1991

By J Li, H Hooi, D Payne

Caval Ridge Mine (CVM) is one of the newly established open-cut coal mines of BHP in Queensland, where no tailings dam is planned to be built in order to minimise environmental impacts from mining activities. The waste streams from the Coal Handling and Processing Plant, including fine tailings dewatered by belt filter presses, coarse rejects, and mixed plant rejects, are co-disposed within waste dumps built with pre-strip and dragline spoils. Due to high rejects output (35 – 60% of feed) and low spoil to reject ratio (< 5) the large quantities of rejects bring significant geotechnical and operational challenges to CVM, which are exacerbated by increasing annual production rates and additional rejects from washing coal from an adjacent mine. Further in-house geotechnical review commenced in mid-2014 based on the initial geotechnical studies during the project stage of CVM between 2011 and 2013. The outcomes have enabled rejects disposal at CVM by constructing large belt filtered tailings cells, coarse rejects only dumps, and co-disposal of the mixed plant rejects at dump tip-heads. This paper presents the rejects disposal strategies at CVM from both technical and operational aspects. It also discusses future projects for belt filtered tailings moisture reduction including assessment of tailings clay mineralogy, as well as mixed plant reject co-disposal verification and optimisation.CITATION:Li, J, Payne, D and Hooi, H, 2018. Plant rejects disposal strategies applied at Caval Ridge open cut coal mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 50–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R. R. Klimpel

In three recent publications, Klimpel et al (1988) and Klimpel and Hansen (1988, 89), the theory and invention process behind the identification of two new classes of sulfide mineral collectors were summarized. These two new families can be represented by the 111 generalized formulate: R1-S-R1 -NRI III (denoted as the F-series chelation family) and R-S-R or R -CHSCH-R (denoted as the S-series redox family). The influence of systematic changes in the various R groupings on laboratory batch flotation cell tests has been covered in the above references and will not be repeated in this paper. In particular, the recent article by Klimpel and Hansen (1989) should be studied as a research introduction to this paper.

Jan 1, 1989

By Dale K. Fields

With today's technological advances in mineral processing equipment, there is an increasing demand for accurate system control. This can only come about through representative sampling. The purpose of this paper is to guide you in the selection of sampling equipment and outline design parameters for the cutters used in dry and wet sampling without adding redundant mathematical probability formulas to your files. Special attention will also be given to the equipment used in conjunction with samplers and sampling systems, such as feeders, crushers, chutes, launders, and controls.

Jan 1, 1979

By Norman O. Lotter, Dominic Fragomeni, Lori J. Kormos, Guy Comeau, Antonio Di Feo

"A performance opportunity was identified for the Raglan concentrator operation by changing the selection of xanthate from Potassium Amyl Xanthate (PAX) to Potassium Isobutyl Xanthate (PIBX). This opportunity was identified by a Statistical Benchmark Survey of the operation and QEMSCAN measurement of these survey samples, in which fine liberated pentlandite was found in the final tailings. This was confirmed by some laboratory scale flotation testwork using High- Confidence Flotation Testing. A statistically designed plant trial was implemented in 2007 to measure and confirm the performance gain. This trial design used on-off switching following a three-month reference distribution of normal operations using PAX. This layout provided both external and internal reference distributions on PAX to be established. These were used to evaluate the internal reference distributions on PIBX. This trial format was deliberately designed so as to block out the effects of autocorrelation in the operations data. In this way, small but significant metal recovery gains may be measured and proven in a plant trial. The paper describes the case study to show that this approach successfully blocks out autocorrelation in time, which is an obstacle in analysing concentrator operations data. The results showed that the PIBX had produced clear and statistically significant recovery gains for Ni, Cu, Pt and Pd. Adjusted for feed and concentrate grades, these recovery gains were: Ni: 1.00, Cu: 0.96, Pt: 5.07 and Pd: 1.90%.INTRODUCTIONConcentrator OperationsMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes. These have traditionally been used to treat ore that has been mined, producing a lowbulk concentrate containing a high percentage of the paymetal(s) in the ore mined. These concentrates are more economically treated in subsequent beneficiation processes than the ore from which they were produced.This choice of a concentration process results in a significant and variable paymetal loss to the concentrator tailing. This tailing is discarded and disposed of in an impoundment area, and has no immediate business use. This paymetal loss forms the largest loss of paymetal in the entire flowsheet by which refined, or saleable, metal(s) are produced [Cramer, 2001]. The question arises as to whether any particular concentrator is performing at its full potential, and how this answer may be determined. In a concentrator operation, there is always an ongoing performance improvement programme for this reason."

Jan 1, 2009

By F. Rudloff, C. Karageorgos, J. Moyo, I. Boadi, M. Struble, B. Lumsden

Over it’s more than 100-year history, the Kennecott operation has often been at the forefront of innovation; driven by the demands of the lower grade ore-body and the higher costs of operating in the US where wages are generally higher and regulation more restrictive. One way of reducing operating costs in c/lb is to increase the lbs produced at minimal cost. Despite the relatively coarse grind at Kennecott - about 30% >150μm, approximately 20% of the Cu lost to tail is liberated chalcopyrite in the <20μm fraction, and about 30%-40% in the <37μm fraction. In 2020 Kennecott undertook a detailed plant scale test of the magnetic aggregation technology to increase copper recovery by reducing fine copper losses. A paired statistical plant test of magnetic conditioning on one rougher line showed a 1.12% increase in Cu recovery to 97% statistical confidence. The next challenge, unforeseen at the start of the project, was the fabrication and transportation to site of the equipment for the three remaining rougher rows, during the severe supply-chain constraints of the Covid pandemic in 2021. This resulted in delays and unforeseen costs as world-wide transportation became chaotic, particularly transportation via west coast USA. Nevertheless, the project was completed and commissioned, with only minor delays and cost increases, due to a flexible approach to overcoming the hurdles encountered.

Feb 1, 2023

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By B. S. Xakalashe, I. J. Geldenhuys, M. W. Erwee, Q. G. Reynolds, R. T. Jones, S. P. Tsebe

Aspects of the production of platinum group metals by reductive smelting in direct-current arc furnace processes are investigated using a computational modelling approach. The replacement of fossil carbon as a reductant by alternative reductants such as silicon carbide, ferrosilicon, and hydrogen is desirable for reducing direct greenhouse gas emissions from such processes, but the impact of these changes on the electrical operability of the process is poorly understood. This paper presents a study of plasma arc behaviour in the context of the ConRoast® reductive smelting process for Upper Group 2 ore as well as processes for recycling of automotive catalysts, using an integrated computational modelling workflow. It was found that the freeboard gas compositions, plasma properties, and arc behaviour were all affected by the choice of reductant, particularly in carbon-free smelting using ferrosilicon or hydrogen.

Mar 6, 2026

By Patrick R. Taylor

A novel method for Chemical Vapor Infiltration (CVI) using plasma technology is proposed, Plasma Enhanced CVI (PE-CVI). Due to the low rates at which CVI is currently performed, the use of plasma as a source of heat may be considered to be a faster and less expensive production method. Precursors fed in the hot region of the plasma gas are completely vaporized and forced by the same flow through a porous preform where it condenses as a new material. In this research, silica and methane where used as precursors to form SiC/on a / graphite felt (preform). To enhance the infiltration process, vacuum was used to increase the flow through the preform. Characterization of infiltrated graphite was perfontied using Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD). A uniform distribution of Sic was observed along the felt with only twenty minutes of infiltration process, yielding a 178% increment in weight.

Jan 1, 1997

By Alan DonaldsoN

Plasma Quench production of titanium is the thermal dissociation of titanium tetrachloride into gaseous titanium and chlorine followed by rapid quenching to prevent back reactions. Titanium tetrachloride dissociates into titanium and chlorine atoms at 5000 K. Expansion through a Delaval nozzle accelerates the gas to supersonic speed cooling it very rapidly. Cooling rates are as high as 7exp 1 0 Kelvins per second. Injected hydrogen reacts with condensed titanium particles to form titanium hydride and with the chlorine to form hydrogen chloride. We have produced titanium powder at 20 kglh in a continuous reactor. Costs are projected to be lower than the Kroll Process at large enough scale. Most of the cost reduction would result from elimination of magnesium as a reducing agent and much lower capital costs.

Jan 1, 2001