Search Documents

By Robert A. Speirer, Richard G. Burdick

Methods of detecting geologic faults and other linear features by means of processed LANDSAT satellite images have gained prominence during the past several years . There have been numerous programs written to pick these " lineaments , " but they have been almost universally tailored to large computers . This Bureau of Mines report describes a detection method developed for use with a minicomputer . The method comprises a suite of programs that scans an image for all " potential " lineaments . From this partially analyzed data , the final lineaments are picked by another routine . The method was field tested in an area of south- central Wyoming , and results indicated good agreement between computer- picked lineaments and ground features . Most of the known geologic faults in the area were picked by the method . Such features as roads and trails were also picked but were easily distinguished from faults during field inspection . The method is relatively new but promises to be a viable reconnaissance technique for the mining industry in geologic structural analysis .

Jan 1, 1965

By M. J. Ferrante

New data on zirconium tetraiodide (ZrI4) have resulted from high-temperature enthalpy and X-ray powder diffraction studies conducted by the Bureau of Mines. These studies were undertaken as part of the Bureau's efforts to provide important thermodynamic data essential to the advancement of mineral resources technologies that can be employed with minimal energy requirements and minimal environmental degradation. Enthalpies were measured with a copper-block drop calorimeter. No transitions or other anomalies were found. Tabulated values are given from 298.15 to 772 K for relative enthalpy, heat capacity, entropy, and Gibbs energy function. Enthalpies are expressed in equation form and combined with data from the literature to calculate values of the standard enthalpy of formation and the Gibbs energy of formation. X-ray powder diffraction data indicate that ZrI4 is primitive cubic with a lattice parameter of 11.79 A and is isostructural with stannic iodide (SnI4).

Jan 1, 1980

By J. M. Stuve

This Bureau of Mines investigation measured the low-temperature heat capacities of FeOC1(c) and FeC13(c) in the temperature ranges of 6 to 305 K and 4.6 to 300 K, respectively. The standard entropies (S°, 298.15 K) of FeOCl(c) and FeC13(c) were derived as 19.73±0.03 cal/deg-mole and 35.33±0.07 cal/deg-mole. A large lambda transition was observed in the heat capacity of FeC13(c) at 8.4 K. The standard enthalpy of formation (?H°f, 298.15 K) of FeOC1(c) was determined to be -98.23±0.22 kcal/mole by HC1 solution calorimetry. High-temperature enthalpy measurements (H-H298.15) of FeOC1(c) were determined to 700 K by precision drop calorimetry. Standard thermodynamic formation data and related functions were tabulated at various temperatures for FeOC1(c) and FeC13(c).

Jan 1, 1980

By George M. Lucich

This report describes a sensitive, proportional temperature controller developed by the Bureau of Mines that is useful in the temperature range from 40 to 400° C with an accuracy of ±0.10 C. A temperature controller of this kind is potentially useful for regulating temperatures in air chambers, liquid baths, furnaces, and reaction vessels, and for other applications. This instrument was developed to control the duration and temperature of the heating cycle of a charcoal-filled adsorber that is part of a special helium analyzer used by the Bureau. The controller was made from commercially available parts, and can be easily modified to provide continuous temperature control. The circuit is solid state and employs no electromechanical devices. Over a 2-year period of use as a component of the special helium analyzer, this temperature controller performed successfully and required no maintenance.

Jan 1, 1979

By M. M. Jones

A procedure for the spectrophotometric determination of uranium has been developed in support of minerals research being conducted by the Bureau of Mines. Uranium is separated from the sample by tributylphosphate extraction from acid solution containing added aluminum nitrate and (ethylene dinitrilo)-tetraacetic acid solutions. The colored uranium-dibenzoy1methane complex is developed in the organic phase by adding an ethanol solution of dibenzoylmethane buffered with triethanolamine. Absorbance is measured at 410 nanometers, and the response is linear up to at least 100 micrograms U30S in the aqueous aliquot taken for analysis. Aliquots containing as little as 8 micrograms U30S may be analyzed with relative errors no greater than ±5 percent. For aliquots containing at least 35 micrograms U308, relative standard deviation at the 95-percent confidence level is about ±2.2 percent. Appropriate procedures are given for analyzing a wide variety of samples.

Jan 1, 1980

By Michael J. Beus

This Bureau of Mines report describes field investigations conducted in the Coeur d'Alene mining district of Idaho to obtain data on rock stress and physical properties. The resulting information has been utilized as input to detailed finite-element analyses to establish structural design criteria for deep-vein mine shafts. Measurement techniques include the Council for Scientific and Industrial Research biaxial and triaxial strain cells, the U.S. Geological Survey solid-inclusion probe, and the Colorado School of Mines dilatometer. Physical property testing was conducted in the laboratory on core obtained from each test site. Limited in situ physical property tests were also conducted. Reason-able success was obtained with the CSIR equipment, which was considered the most suitable for stress measurement in the study area. Test sites ranged in depth from 1,200 to 7,700 feet and are described in detail. The stress data were reduced by least-squares linear regression techniques to enable prediction of vertical and horizontal stresses to 7,500 feet. Ratios between the horizontal stresses as utilized for shaft design varied considerably, and a hydrostatic condition is the exception, based on Bureau measurements. Physical properties also varied widely, due to the complex geologic structure. Analyses of the data in terms of the tectonic history of the area show reasonable correlation. Data from previous rock mechanics investigations from the Coeur d'Alene district were also compiled and presented as part of this report to justify any generalizations regarding stress conditions and physical properties of the district as a whole.

Jan 1, 1980

By August J. Kwitowski

This Bureau of Mines report describes how the reinforcement mechanisms of untensioned, full-column resin bolts were determined during one underground study. Both axial and transverse shear loadings were identified for two instrumented resin bolts that replaced standard resin bolts in an opera-ting room-and-pillar mining section. The strain responses of resin bolt steel cores to local axial and transverse shear loadings are described. This information was obtained from laboratory testing of resin bolts installations; it was also used to analyze the data from the underground test.

Jan 1, 1980

By J. M. Stuve

Low-temperature heat capacities of chiolite (Na5Al3F14) were determined by adiabatic calorimetry in the temperature range 5.8 to 300 K. The derived standard entropy (S°, 298.15) was 115.6 ± 0.2 cal/deg-mole. High temperature enthalpies relative to 298.15 K were obtained by precision drop calorimetry up to 1,000 K. Tables of experimental data and related thermodynamic functions are given for the temperature range of experimental observations.

Jan 1, 1980

By Stephen D. Cramer

The Bureau of Mines conducted a study in which the magnetic fraction of urban refuse was used as melting stock in the preparation of high-strength, low-alloy and carbon steel. Product steels, made from incinerated steel can scrap, nonincinerated-nondetinned steel can scrap, nonincinerated-detinned steel can scrap, and dilutions of these scraps with No. 1 heavy melting scrap, were used in continuing tests in industrial, rural, and marine environments to determine the effect of residual elements and atmospheric pollutants on their atmospheric corrosion resistance. The respective commercial steels were exposed at the same time to establish baseline corrosion data for the test sites. Weight-loss data are reported for atmospheric exposures of 0.5, 1.0, 1.5, and 3.8 years. The marine environment was the most corrosive; the industrial environment was the least corrosive. The atmospheric corrosion resistance of the carbon steel was improved 25 pct by using incinerated scrap and nonin-cinerated-nondetinned scrap in the steelmaking process. In no case was the atmospheric corrosion resistance of carbon steel degraded by using the magnetic fraction of urban refuse as melting stock. The presence of sulfur in the corrosion film was the most important factor affecting the corrosion resistance of the steels. With increasing sulfur concentration, the rate of the corrosion reaction was reduced and the corrosion film became more protective. The residual elements in the product steels most responsible for improving corrosion resistance were copper and tin. These elements tended to increase the concentration of sulfur in the corrosion film. At the levels present in the product steels, Cr, Ni, and Pb had no observable effect on the corrosion resistance of the steels.

Jan 1, 1980

By L. A. Neumeier

The Bureau of Mines investigated hot-rolling and forging characteristics of experimental ductile iron castings, both sand and permanent-mold, made with charges containing up to 70 pct foundry pig iron and 95 pct steelmaking pig iron. Between 1,550° and 1,950° F, most castings could be rolled to 90-pct reduction or forged to 70-pct reduction without serious cracking. Charge and composition have less bearing on workability than on subsequent properties. Permanent mold castings could be worked as readily as sand castings at 1,750° and 1,950° F. Plasticity improved with temperature. Small billets were also forged cold to 50-pct reduction without cracking. With equivalent nodularity, composition affects properties of wrought materials by altering matrix structure and strength. Properties vary with reduction and improve with increasing working temperature. Rolled material has high strength and anisotropy, and low ductility, particularly in the trans-verse direction. Annealing reduces strength and improves ductility, but anisotropy persists. At 70-pct reduction, impact resistance in the longitudinal direction is about twice that in the transverse. Annealing roughly doubles impact resistance. Deformation enhances damping capacity. The feasibility of die-forging and bar-rolling of ductile iron was evaluated in trial tests conducted under a Bureau contract. Although workability and ductility of ductile iron are inferior to those of steel, more advantage could be taken of ductile iron's plasticity to work rough shapes to final dimensions.

Jan 1, 1980

By K. O. Bennington

The thermodynamic properites of petalite (Li2A12Si8O20) were determined by the Bureau of Mines. The enthalpy of formation was determined by hydro-fluoric acid solution calorimetry. The values from the elements and from the oxides are ?Hf°298.15 = 2,335.8 ± 3.0 kcal/mole and ?H°295 (from oxides) = -50.60 ± 1.20 kcal/mole. Low-temperature heat capacities were determined by adiabatic calorimetry from 10.69 to 302.11 K. The derived standard entropy is S°298.15 = 111.0 ± 1 cal/deg-mole. Enthalpy increments above 298 K were measured by copper block calorimetry from 298 K to 1,193.6 K. The various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature from the elements and constituent oxides. The Gibbs energy of formation is ?G°f298.15 = 2,203.8 kcal/mole.

Jan 1, 1980

By C. E. Jordan

The Bureau of Mines is conducting research into the pneumatic recovery of coarse mica and has used this method to produce mica concentrates that contain more than 90 percent mica. This research is being carried out pursuant to the Bureau's objective to develop technology that will help maintain an adequate supply of minerals and metals to meet national economic and strategic needs. Researchers used a Bureau-designed system of crushers, screens, and zig-zag air classifiers to concentrate coarse liberated mica particles from mica-bearing materials. This pneumatic system was used to concentrate four mica ores from Arizona, North Carolina, and South Dakota and three waste tailings from Alabama, Georgia, and South Dakota. Using these samples, it was demonstrated that plus 65-mesh size mica can be effectively recovered by the pneumatic method. Not only were the concentrates high in mica content; it was also demonstrated that this method can be used to recover up to 78 percent of the mica that was originally contained in the samples. Because it is a dry concentration method, the pneumatic beneficiation technique may be advantageous in areas where water resources are limited.

Jan 1, 1980

By H. J. Heinen

The Bureau of Mines, investigated a cyanidation-carbon adsorption technique for extracting gold from arsenopyrite concentrates. Agitation leach experiments were conducted on 85-pct-minus-35-mesh gravity concentrates containing 21.8 oz gold and 6.4 oz silver per ton. Results obtained in leaching the concentrates showed that 96.9 pct gold and 90.7 pct silver extraction could be achieved in 96 hours of agitation. Gold and silver were recovered from the resulting pregnant solution by exposure to granular activated carbon in a countercurrent system. Carbon loadings of 2,556 oz of gold and 502 oz of silver per ton were achieved. These loadings are significantly higher than heretofore thought practical.

Jan 1, 1980

By Franklin B. W. Woodbury

The Bureau of Mines, as part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic A needs, is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed on a prototype monitoring system utilizing a Californium-252 (252-Cf) neutron source and a thermal neutron capture-gamma ray spectra analysis method to measure the amount of iron and percent solids in process slurries. The prototype system was used to monitor the concentrate and tailing streams in a 900-lb/hr flotation pilot plant during continuous around-the-clock tests. The iron content of the process slurries was determined by measuring the total peak areas under the capture spectrum peaks at 7.626-7.632 MeV, the associated escape peaks at 7.136-7.122 and 6.626-6.612 MeV, and the iron doublets at 4.900 and 4.998 MeV. A potential method for determining the percent solids in process slurries using the 2.22 MeV hydrogen capture peak is discussed. Results of this work demonstrate a potential method for providing process control parameters using the data from thermal neutron capture-gamma ray reactions.

Jan 1, 1980

By H. R. Beard

The Bureau of Mines investigated the absorption of radium and thorium from waste uranium leach liquor by clays and other materials. This work was conducted in support of the Bureau's goal of minimizing the environmental conflicts, impacts, and occupational hazards associated with mining and milling operations. Tailing and soil samples from New Mexico were evaluated for their potential to absorb radium and thorium from tailing liquors. Absorption ranged from 0 to 97 pct for radium and 0 to 60 pct for thorium. Some samples that readily absorbed radium were contacted with various salt solutions that could be present in tailing solutions to determine whether desorption would be a potential problem. The desorption of radium ranged from 0 to 75 pct. An alpha spectrometric method was used to determine the radium and thorium concentrations in the solutions and solids.

Jan 1, 1980

By E. L. Litchfield

Four short-term studies of practical ignition problems were undertaken and completed during the course of the Bureau of Mines project "Development of Specifications for Intrinsically Safe Equipment." Conclusions were as follows: (1) the most easily ignitible mixture of propane-air in a PTB break flash apparatus is approximately 5.2 percent propane; (2) miniature lamp bulbs to be used in intrinsically safe circuits are about as incendive to coal dust-air as to methane-air and should be tested in gas mixtures containing about 7.0 to 7.5 percent methane; (3) the sodium amalgam contained in high-pressure sodium lamps does not present an ignition hazard for coal dust or methane, where the lamps contain no more than 30 milligrams of amal-gam; (4) the maximum allowable surface temperature of permissible electrical enclosures should remain at 150° C despite efforts by industry groups to raise the value to 200° C.

Jan 1, 1980

By W. D. Riley

The U.S. Department of the Interior, Bureau of Mines, has been conducting minerals recovery research in support of the nation's geothermal program since 1974. The Bureau's program of laboratory and field studies has focused on determining the materials of construction for geothermal resource recovery plants and an the recovery of mineral values from the geobrines. An analytical program has been conducted at the Avondale Research Center to determine the chemical constituents of some high- and low-salinity geobrines found in the Imperial, Valley of California. Data are reported for the early stages of brine production of femur geothermal wells--the low-salinity, medium-enthalpy brines from the East Mesa Known Geothermal Resource Area (KGRA), Mesa 6-1 and 6-2, and the high-salinity, high-enthalpy brine from the Salton Sea KGRA, Magmamax 1 and Woolsey 1. The reported results indicate the importance of the operating and engineering history, the operating parameters during sampling, and the method of sampling in order to evaluate the chemical analyses.

Jan 1, 1980

By Steven J. Page

The Bureau of Mines used fiber-laden air to test two identical fibrous aerosol monitors (FAM) in order to establish the FAM-optical count correlation. The FAM is a unique instrument developed by GCA Corp. (GCA) to measure real-time fibrous aerosol concentrations. It will also respond to particulates that have sufficient shape irregularities to possess fiber characteristics such as the 3:1 length: diameter (L:D) aspect ratio. Results of the Bureau's laboratory tests showed that the FAM response is linearly correlated to concentration data obtained using the optical membrane filter count technique approved by the National Institute for Occupational Safety and Health (NIOSH), U.S. Department of Health, Education, and Welfare. A plot of the FAM-optical count correlation showed that FAM concentration readings are generally well within ±25 pct of the optical membrane filter count. Initial tests to estimate the best ratio control setting of the FAM for 5-µm fiber-length discrimination were performed using one instrument only (the ratio control setting determines the minimum threshold fiber length that will be detected by the FAM). The estimated setting was then used to correlate both FAM units. The result was a 65 pct difference in correlation between the two units. It appears that the major factor responsible for this difference was the internal adjustment of the photomultiplier detector sensitivity for each of the two FAM units.

Jan 1, 1980

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980

By H. O. McDonald

Solutions containing Cr6+ and sulfuric acid are used in a number of surface-finishing operations. Substantial quantities of chromium and copper are lost and pollution problems are created when the spent solutions are discarded. To minimize the undesirable environmental effects while improving secondary resource recovery technology, the Bureau of Mines is conducting research to detoxify and recover metals from these solutions. Spent etchants are treated to remove copper and reduce Cr6+ to Cr 3+ in an electrolytic cell. The anodes and cathodes are granulated coke. The spent solution is continuously pumped through the electrodes. Hexavalent chromium is reduced to trivalent chromium, and copper is recovered at the cathode. Reoxidation of Cr3+ at the anode was not observed. The removal and recovery of copper reduction of Cr6+ lessen chemical demand and increase efficiency in waste in treatment operations associated with the use of these solutions.

Jan 1, 1980