Search Documents

By D. N. Tallman

The electrokinetic properties of MgO have been utilized to simultaneously filter suspended solids and remove trace amounts of dissolved heavy metals from synthetic mine water. Greater than 95 pct removal of metals from influent at neutral pH containing 1 to 6 mg/L of dissolved Cd, Cu, Mn, Ni, and Zn can be routinely achieved by filtering through a granular bed of MgO at flow rates typical of rapid sand filtration (0.3 cm/s). Filtrate concentrations of most metals can be maintained below 0.1 mg/L for 160 bed volumes or more loading. The more mobile metals (those with larger solubility products) are more difficult to remove, and are strongly bonded to the MgO granules so that chemical stripping with chelating agent is required to clean the bed. Less mobile ions are easily removed by the filter and are effectively stripped by conventional filter backwashing. The fraction of metals recovered by chemically stripping the loaded MgO filters correlates to the zero points of charge of the metals. This process may be applicable to removal and recovery of trace amounts of heavy metals in mine drainage that is partly neutralized by liming. Also, since many of these metals are critical and strategic, the technique can be adapted not only to recycle process water from mineral and milling waste streams, but also to reclaim their metal values.

Jan 1, 1986

By Dennis A. Hansen

The solubility of anhydrous aluminum chloride in solutions of titanium tetrachloride and vanadium tetrachloride was determined as part of a re-search project-by the Bureau of Mines to make a homogeneous alloy sponge of titanium, vanadium, and aluminum. Solubility curves were established using an autoclave at 75°, 100°, 125°, and 150° C. The solubility of AJC13 in TiC14 is 0.2 wt pct at 75° C; it increases to 18.3 wt pct at 150° C. The data concur with data from earlier researchers of this bi-nary system for 75° to 125° C. For the VC14-AlC13 binary system the solubility of AlC13 is 0.1 wt pct at 75° C, increasing to 1.6 wt pct at 150° C. For the TiC14-AlClrVC14 ternary system the solubility of AlC13 decreases from the values found with a pure TiC14-AlC13 system to the lower values found with a pure VC14-AlC13 system at the respective temperatures.

Jan 1, 1986

By J. C. Judd

The Bureau of Mines investigated the recovery of vanadium, uranium, and phosphorus from low-grade phosphorite ores and concentrate by leach-ing with H2S04. Samples containing 0.12 to 0.23 pct V20S, 0.009 to 0.012 pct U30S and 18 to 30 pct P20S were treated by batch-agitation leaching, roasting followed by acid leaching, salt-roasting followed by acid leaching, and leaching under pressure. Maximum recoveries using leaching alone ranged from 78 to 98 pct of the V20S and 74 to 88 pct of the U30S-Leaching under pressure resulted in extractions of 88 to 95 pct of the V20S and 84 to 89 pct of the U30S. Leaching following roasting--with or without NaCI--produced extractions of 97 to 99 pct of the V20S and 86 to 91 pct of the U30a. Depending on the technique(s) employed, phosphate extractions ranged from 89 to 99 pct. Solvent extraction laboratory tests were conducted to selectively re-cover vanadium and uranium values from acid leach solutions. An average of 95 pct -of the U30a was recovered using di(2-ethylhexyl) phosphoric acid, plus trioctylphosphinic oxide. Essentially all of the V20S was recovered with octylphenyl acid phosphate plus isodecanol. The phosphate remained in the raffinate.

Jan 1, 1986

By John W. Kopp

A major concern with blasting at surface mines is generation of ground vibrations and airblast and their effects on nearby residences. This Bureau of Mines report looks at the use of millisecond delays in blast design and their effect on the resulting ground vibrations and airblast. A total of 52 production blasts were instrumented and monitored at a surface coal mine in southern Indiana. Arrays of seismographs were used to gather time histories of vibrations and airblast. The data were analyzed for peak values of vibration and airblast and for frequency con-tent. Various delay intervals were used within and between rows of blastholes. Delay intervals within rows were 17 and 42 ms, and those between rows ranged from 30 to 100 msj these intervals are equivalent to 0.5 and 1.3 ms/ft within rows and 1.2 to 4.3 ms/ft between rows. Sub-sonic delay intervals within rows reduced airblast by 6 dB. Large delay intervals between rows reduced the amplitude of ground vibrations; their frequency depended primarily upon the geology of the mine site.

Jan 1, 1986

By F. W. Benn

The Bureau of Mines investigated flotation methods for recovering fluorite and byproducts from two samples of the Fish Creek deposit in Eureka County, NV. The preferred method for tre.ating a fluorite-beryllium sample included (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, (3) muscovite flotation, (4) silicate flotation, (5) sodium hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concen-trate. Laboratory results showed that over 94 pct of the fluorite was recovered in a recleaner concentrate containing 98 pct CaF2, Beryllium flotation produced concentrates containing in excess of 5 pct BeO with recoveries over 70 pet. The preferred method used for a fluorite-mica sample consisted of (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, and (3) mica flotation using an anionic-cationic collector system. Laboratory results showed that 84 pct of the fluorite was recovered in a recleaner concentrate containing 96 pct CaF2, Mica flotation produced a concentrate containing 95 pct mica at 85-pct recovery.

Jan 1, 1986

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986

By J. H. Tylczak

The Bureau of Mines studied the effect of alloy additions on abrasive wear of low-alloy steels. A dry-sand, rubber-wheel abrasion test appa-ratus using ASTM G65-Sl procedure B was used for the abrasive wear tests. Eighty-six material heat-treatment combinations were abrasion tested. Results of these tests were analyzed statistically using regression analysis to see if additions of Cr, Mn, Mo, Ni, Si, AI, Cu, and S were significant in affecting the abrasive wear rate of low-alloy steels. Regression analysis was also used to confirm hardness and C affect on the abrasive wear rate of these steels. It was found that for all the steels taken as a group, increased amounts of Mn significantly reduced the wear rate, while increased amounts of Mo and S1 increased the wear rate. Analysis also confirmed previous research done by others, that increasing hardness and amounts of C reduced the wear rate. For the hardened steels taken as a class, only increasing amounts of C and Mn reduced the wear rate, while increases in Si increased the wear rate. In the class of unhardened steels, increases in C, Mn, and S re-duced the wear rate, whereas increases in Mo increased the wear rate. The steels with the best resistance to wear were two hardened experimen-tal steels similar to AISI 1055 and AISI 107S.

Jan 1, 1986

By R. D. Wilson

Ten to twelve million tons of dust is produced by cement kilns annu-ally in the United States, resulting in a serious waste disposal problem. The Bureau of Mines investigated two alkali volatilization methods for converting this dust into materials for making portland cement and a useful potassium product. Portland cement kiln dust was found to be composed of finely ground cement raw materials (CaC03 and 8i02) having a layer of alkali sulfate (K2S04 and Na2S04). In this form, it cannot be directly recycled to cement kilns because concrete is weakened by a reaction between the alkali and the aggregate. Portland cements with 28-day strengths above 5,000 psi were produced from low-alkali residues using sintering and melting methods. For nearly complete removal of alkalies, primarily potassium sulfate, from cement kiln dust, a temperature above 1,300° C and a reducing atmosphere were required.

Jan 1, 1986

By Laxman S. Sundae

The Bureau of Mines designed, fabricated, and is using an in-seam tester (1ST) for in situ determination of coal cutting forces. This re-port describes the results of field tests conducted in the Pocahontas No. 3 and Upper Freeport seams to obtain peak and mean cutting forces during coal cutting with several bit geometries, including radial and point attack bits currently used on drum-type machines. Comparisons were also made between new and worn bits, and using data obtained from a Bureau-modified chisel bit. The test results show that longwall plough cutting (horizontal cuts) in bony coal bands (shale) requires >3 times the cutting force for the same cuts in a vertical direction. When no bony coal is present, the cutting forces required to make horizontal and vertical cuts are equal. Worn bits require 4 to 5 times more cutting and normal force than new or undamaged bits. Normal force increased drastically for the worn chisel bit. Peak force encountered in making independent cuts was found to be ~3 times higher than that required to make interactive cuts using a spacing-to-depth-of-cut ratio of 2. Both rake and clearance angles were found to have a significant effect on normal and cutting force.

Jan 1, 1986

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau's measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau's investigations. Typical comparative data are included.

Jan 1, 1986

By Steve W. Webb

The Bureau of Mines is researching a new technology for dewatering clay suspensions that consists of flocculation by high-molecular-weight poly-ethylene oxide (PEO) polymer and subsequent removal of water from the floes via a trommel. The minimum amount of PEO required to dewater the clays depends on the ions adsorbed on the surface of the elay particles. Infrared studies were performed on clays with Li+, NH4+, K+, Mg2+, Ca2+, Ba2+, or 8r2+ adsorbed, with and without adsorbed PEO, to develop data to aid in understanding the dewatering mechanism. Hydroxyl stretching modes between 3,400 and 3,250 em-I, associated with water adsorbed on the clay, showed changes in intensity proportional to the ionic eharge-to-radius ratio; that is, the ionic potential. In addition. a water-bending vibration of adsorbed water at 1,630 cm-1 showed variations associated with water desorption. The data are consistent with changes in adsorption of PEO resulting from variation of the acidity of water coordinated with the exchange ions, induced by the variation in field strength of the ions with the ionic potential.

Jan 1, 1986

By Robert A. Jankowski

Through laboratory and underground studies, the Bureau of Mines has evaluated the use of passive barriers (dust shields) to help confine dust generated by longwall shearers to the face area. Laboratory studies focused first on selection of the optimum barrier design, which proved to be a simple, gobside barrier (made of conveyor belting), coupled with a headgate splitter arm, which was found necessary to prevent the dust cloud from entering the walkway at the headgate end of the shearer when cutting tail to head. Further laboratory testing was done to determine whether using passive barriers in combination with different water-spray dust-reduction methods, including the shearer-clearer system developed by the Bureau, would improve dust reduction over that from using the water sprays alone. It was found that the combination of gobs ide passive barriers plus the full shearer-clearer system was most effective, and surmised that this would be especially useful in thicker seams. However, underground testing revealed that the shearer-clearer system alone was 35 pct more effective in reducing dust contamination than when used with the gobside passive barriers, and far more effective than using passive barriers with a conventional water spray system. For such an effective system as the shearer-clearer; the reduction in avail-able space over the top of the machine actually impeded system performance; this was shom1 in both eastern and western mines. But when used with comparatively inefficient water spray systems, the passive barriers, used in combination with a headgate splitter arm, provide consider-able help in reducing dust levels in the walkway.

Jan 1, 1986

By Kenneth E. Hay

The Bureau of Mines collected coal and coal waste aggregate material from two different mine sites to determine their strength characteristics for use in concrete. The concrete would be placed underground as support walls for ground control in adverse conditions or unique mining applications. A standard mix design was established for a "wet" mix using a water-to-cement (w/c) ratio of 1.0 to facilitate pumping into place. Later, material was collected from four more mine sites and used to make 2-by 2-by 2-ft test blocks with the same w/c ratio. A pull-out cone device and borehole shear tester were used to determine the in situ material strength of the test blocks. These techniques will provide a simple and quick way of determining support wall strength in an underground environment. Test results from the pullout cone de-vice showed a good correlation of 0.98 to test cylinder compressive strengths of the same mix. Results of the borehole shear tester were inconclusive.

Jan 1, 1986

By M. J. Ferrante

Relative enthalpies of V20S from 298.15 to 1,101.0 K were measured at the Bureau of Mines to provide data needed for the advancement of min-eral technology. Enthalpies were measured with a copper-block calorimeter. A sharp melting point was found at 951 K, with [~~ = 15.690 kcal/ mol ] for the standard enthalpy of melting. Tabulated values are given at selected temperature increments between 298.15 and 1,500 K for the standard relative enthalpy [(HO -H~98),] heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)/T]. Standard relative enthal-pies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1986

By Jeffrey M. Listak

The Bureau of Mines has conducted a rock mechanics study to monitor deformation of near-seam strata above a longwall panel in the Pittsburgh Coalbed. The primary goal was to determine the height of caving immediately behind advancing longwall face supports. This study, although site specific, provides information on the caving mechanism associated with longwall extractions so that strata behavior and its interaction with longwall face supports can be better understood. Two holes were drilled, approximately 550 ft apart along the center line of a longwall panel, from the surface to the coalbed approximately 650 ft below. Various downhole geotechnical instruments were used to monitor strata deformation. In addition, surface elevation surveys were conducted to differentiate between surface and subsurface activity. This report discusses the caving characteristics of the strata as the longwall panel approached and passed beneath the boreholes. Physical property data are also presented to demonstrate the relationship between caving behavior and local geology. Data show that immediate caving of strata above the longwall face occurred at a height less than 23.5 ft and that strata behavior above longwall extractions is highly dependent upon lithology, with major disturbances occurring at weak lithologic zones.

Jan 1, 1986

By Seth C. Schaefer

The Bureau of Mines investigated the standard Gibbs energies of forma-tion AGfo, for NiCr204 (nickel chromite) and CoCr204 (cobalt chromite). High temperature galvanic cells employing stabilized ZrOz (zirconia) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1986

By Stephen C. Tadolini

The Bureau of Mines conducted field investigations in two underground mines to determine the actual loads to which bearing plates were subjected when installed in conjunction with full-column resin-grouted bolts and the roof movements generated by the applied loads. Measured loads indicate that the bearing plate is an integral part of the support system. Vertical displacement gauges installed to monitor roof displacements in the test sites show that the highest degrees of loading occur in conjunction with the largest amounts of movement.

Jan 1, 1986

By Margaret R. Egan

This Bureau of Mines report presents results from experimental studies on wood crib fires in an intermediate-scale fire tunnel. Gas concentrations, smoke particle characteristics, heat release rates, and ventilation rates were determined. These measurements form a data base for wood, which can be used with previous analyses for coal and future studies of other mine combustibles, to comprehend the potential hazards of these materials in underground mine fires. A knowledge of the combustion products emitted from these materials will benefit fire detection and control. Results show the changes in burning rate and heat release rate produced by different crib configurations and ventilation rates. Also included are the effects that the burning rate has on smoke characteristics and gas production.

Jan 1, 1986

By P. D. Kovscek

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted mechanical cutting system to determine the effect of the high-pressure sprays on machine performance, airborne dust levels generated, and size of particles formed. Testing was conducted on a simu-lated coal block (coalcrete) while cutting at a water pressure of 190 psi and at water-jet-assisted pressures ranging from 1,000 to 6,000 psi. The shearer motor energy used by the shearer while cutting coalcrete was determined for each cutting condition. Results indicate that the motor energy required by the shearer for each ton of material cut did not vary significantly as the water pressure was increased. Results of dust measurements recorded near the cutting drum indicate that at water pressures above 3,000 psi, dust reductions up to 85 pct were achieved com-pared with cutting with conventional sprays. Analysis of the particle size distribution during cutting showed that increasing the water pres-sure resulted in increased median particle size. In light of these results, various mechanisms for water-jet-assisted cutting are discussed.

Jan 1, 1986