Search Documents

By C. W. Chen

MARTENSITE transformations in ß Cu-Al alloys have been studied by Greninger1 and other investigators. According to Greninger, the parent phase ß1 an ordered body-centered-cubic structure obtained from ß phase by suppressing the eutectoid decomposition, transforms into an ordered hexagonal-close-packed phase in composition containing 12.9 to 14.7 pct Al. The M, temperature decreases with increasing aluminum content; for the alloy containing 14.5 pct Al, for example, the ß1??' transformation occurs below room temperature. More recently, Kurjumow2 studied the transformation in ß Cu-Al alloys with the addition of nickel. His report stimulated new interest in the subject due to the observation of completely reversible transformation without hysteresis in the transformation temperature ranging from 10° to —10°C. In the present paper some characteristics are described of the transformation of Cu-Al-Ni alloys that were partly studied by Kurjumow. Experimental Procedure High purity copper (99.999 pct) and aluminum (99.99 pct) and electrolytic nickel were used in the preparation, by the Bridgman technique, of single crystal specimens which contained aluminum and nickel of 14.5 and 0.5 to 3.0 pct, respectively. Polished surfaces were prepared mechanically. Specimens were then chemically etched to remove distorted material, homogenized at 1000°C for several hours, and quenched drastically to room temperature in a 10 pct NaOH bath to produce the parent phase ß1. The transformation was studied under a microscope and, in some cases, recorded by means of motion pictures. A device similar to that designed by Greninger and Mooradian3 was used to cool and reheat the specimens. Results and Discussion When the specimens were cooled below room temperature, the ß1 to ?' transformation began at 10°C with the appearance of ?' crystals In relief, Fig. la. As the specimen temperature dropped further, the transformation continued, either by the growth of the ?' crystals, with the ß1 — ?' interface moving into the ß1 phase, Fig. 1c and 1d, or by the formation of new ?' crystals, Fig. 1b. As a consequence of the former process, banded structure is observed as a common feature of the low temperature phase. According to the theory of the formation of martensite by Wechsler, Lieberman, and Read,' the bands of ?' phase are probably twin-related, as is the case in the diffusionless phase change of In-T1 alloys,5 but this was not revealed by X-ray tech- niques. New ?' crystals, in needle form, often emerged suddenly across the ?' bands during the transformation. These acicular crystals then grew, both in length and in width, see Fig. 2a through 2d. The transformation on cooling is completed at about -35°C. Upon heating, the reverse transformation started at —10° C, in a manner nearly opposite to the transformation on cooling, and completed at 35°C. There was no noticeable change in the transformation temperature when the nickel content was varied within the limits previously mentioned. Through control of the specimen temperature, the transformation can be started, stopped, or reversed at will. This phenomenon has frequently been observed in the martensite transformation of many nonferrous alloy systems. Other systems are Au-Cd6 and In-Tl.5 ow-- ever, in the latter systems, the transformation is accomplished by single interface motion if the specimen composition is homogeneous and the temperature gradient in the specimen is uniform and sharp, whereas in the Cu-Al-Ni specimens, only multiple interface transformation is observed. The speed of the interface motion appears to be a functionof the rate of temperature change and the temperature gradient across the specimen length. In one case, in which the temperature increased at the rate of 10°C per min and there was no temperature gradient along the specimen axis, the speed of the disappearance of a ?' plate was determined, by the study of the motion pictures made, to be 26 µ per sec. Quench markings were observed on the polished surfaces of specimens. The markings were grouped into one or more sets of different orientations, and were parallel in each set. The ?' plates formed in subsequent transformation were parallel to the markings, indicating that the ?' plates and the quench markings had the same geometric relation-ship to the ß1 matrix. The quench markings on two intersecting surfaces of a specimen were therefore used in the determination of the habit plane of transformation, by the trace method suggested by Barrett.' Results obtained from five sets of markings in three specimens indicate that the habit plane is an irrational plane about 2" from one of the {221} planes. This is very close to the habit plane (3" from 221 planes) of ß Cu-Al alloys containing more than 13.0 pct Al.1 The martensite transformation of Cu-Al-Ni alloys is reproducible. No sluggishness was found between consecutive transformation cycles, although a slight difference in the distribution pattern of the ?' plates was observed, compare Figs. Id and 2d. The transformation can be strain-induced. This characteristic has been tested by a simple method. When a specimen was elastically strained slowly in a vise, ?' plates were gradually produced in the same fashion as during transformation on cooling, This test was done at room temperature, and thus above the M,

Jan 1, 1958

By L. D. Jaffe, D. C. Buffum

EARLY papers1-' reported that temper brittleness is influenced by microstructure. This conclusion was based on room temperature impact tests, the inadequacy of which has been pointed out. Pellini and Queneau7 measured impact energy absorption at —80O to +25oC for several microstructures. On the basis of the shift, associated with temper brittleness, in the energy vs testing temperature curve they concluded that tempered martensite is somewhat more susceptible to temper brittleness than is tempered pearlite. The range of temperatures was insufficient to give complete curves covering the transition from tough to brittle behavior, so it is difficult to evaluate quantitatively the shift for the different microstructures. Also, the smaller shift of pearlite might be attributed to its already being temper embrittled at its temperature of formation. Accordingly, blanks 2 3/16 in. long were cut from a heat of SAE 3140 hot rolled steel barstock, 5/8 in. diameter, on which other work has been reported? A set of blanks was austenitized 1 hr at 900°c, water-quenched, tempered 16 hr at 675oC, and water-quenched, giving a microstructure of 100 pct

Jan 1, 1954

By D. Turnbull, A. M. Turkalo

It is well known that if copper that has been severely cold-worked by rolling (70-98 pct) is heated to high temperatures a small number of large grains are formed at the expense of the fine grained structure that appears upon primary recrystallization. Dahl and Pawlek,' Cook and Mac-Quarie,2 Ward,3 and Boas and Bowles4 have studied this phenomenon in copper. It has been reported as taking place with measurable velocities in the temperature range 700-1080". Boas and Bowles have reported that the time necessary for the transformation is of the order of days at 700°C. According to Ward3 the number of secondary grains which appear in OFHC copper decrease with increasing perfection of cubical alignment after primary recrystallization; also the perfection of cubical alignment increases with decreasing grain size prior to the final reduction. In this investigation two heats, A and B, of especially high purity copper (99.999 pct) supplied by the American Smelting and Refining Co., were used. The behavior of samples prepared from the two heats was qualitatively very similar providing that the grain sizes established prior to the final reduction were about the same. We observed that in specimens prepared from bars which were relatively coarse grained prior to final reduction secondary recrystallization took place at a rapid rate at temperatures as low as 500°C. This is about 200-300°C lower than the temperature necessary to obtain fairly rapid transformation in OFHC copper. A 0.22 in. thick rectangular bar of lot B was cold-reduced 60 pct by straight rolling and given a penultimate annealing treatment at 250°C. Following this it was cold-reduced 90 pct and heated to various temperatures in the range 450-1040°C. The specimens were about 8 mils thick

Jan 1, 1950

By E. C. Roberts

TO facilitate some recent microscopic investigations it was necessary to devise special mounting techniques for the polishing of two quite different metallographic specimens. These techniques are extremely simple and are submitted for whatever value they may be to other investigators. The first specimen mount proved very satisfactory for the study of untempered martensite. Since it was undesirable to heat the specimen, lucite or bakelite mounting materials could not be used in the conventional manner. A cold mount was made by drilling a hole of the same diameter as the specimen in a cylindrical piece of polystyrene then press- ing the steel specimen into the hole on an ordinary vise. A prefabricated disk of lucite should work equally well. The only precautions necessary are that the hole be drilled out cleanly and the piece of steel be pressed into the plastic uniformly, otherwise the mount will crack. The second type of mount was required for the study of slag specimens by reflected light. Mounting these specimens in bakelite and then attempting to rough finish the surfaces on graded emery papers resulted in a considerable amount of chipping and breaking out of the slag particles. This made further satisfactory polishing almost impossible. It was found, however, that if the bakelite-mounted specimen was first rough finished to a point where a good specimen surface became visible, the interstices in the specimen surface could be filled and the polishing completed. This filling was accomplished by placing a small amount of lucite powder in the bottom of the steel specimen mold then reinserting the bakelite-mounted specimen on top of the lucite powder. Reheating the mold to the proper temperature and applying the required pressure resulted in the formation of a thin disk of lucite on the bottom of the bakelite specimen. By carefully grinding the lucite away a uniform surface including the slag specimen was obtained and further polishing was unhampered by slag disintegration.

Jan 1, 1951

By P. R. Hines

Diphenyl guanidine is used as an accelerator in vulcanizing rubber. Other rubber accelerators are also flotation collectors, e.g., dithiocarbamate, thiazole, and the xanthates. Urea and its derivatives are good flotation collectors,' and guanidine is the nitrogen analog of urea. These two characteristics suggested testing diphenyl guanidine as a flotation collector. Diphenyl guanidine has been tried in flotation work previously, but references give no details.'.' Bunker Hill Co. of Kellogg, Idaho, supplied the ore sample used in these tests. The sample was typical of the ore milled in 1949 and contained 4.52 pct Pb and 1.08 pct Zn. A flotation test made by the author with potassium ethyl xanthate as a collector, the same flotation reagents, and the same grind employed in regular Bunker Hill mill practice was the standard for comparing results with the compounds and derivatives of guanidine. The compounds and derivatives of guanidine are only fair collectors of galena. However, if potassium ethyl xanthate were used in the galena float, its presence later in the sphalerite float would make it impossible to introduce another type of collector and be certain which collector contributed the result, so the compound or derivative of guanidine under test was used in both the galena and sphalerite floats in Table I. On both the galena and the sphalerite in the Bunker Hill ore, the depressing action of sodium cyanide and zinc sulfate is much greater with collectors of the guanidine type than with the xanthates. If the depressing agents are left out when a guanidine type of collector is used, but a pH of 8.6 is maintained with either lime or sodium carbonate, the depressing action is approximately the same as in the standard xanthate test. Consequently the depressing agents, sodium cyanide and zinc, were not used in the galena floats of tests 1226, 1228, and 1286, Table I, so the galena floats would be on a comparable basis with the standard xanthate test. As shown by the tests in Table I, the loss in the tail when diphenyl guanidine is used is 8.3 to 9.3 pct, as compared to 17.6 pct with potassium ethyl xanthate, or a recovery of 2.3 to 2.0 lb more zinc. Concentrate grade is 13.7 pct with potassium ethyl xanthate and increases to 22.9 and 31.8 pct with diphenyl guanidine, showing a much higher selectivity. Unless the Barrett's No. 4 coal tar creosote is considered to be a collector, no collector other than diphenyl guanidine is present in the tests, Nos. 1226, 1228, and 1286. Tests 1218, 1253, and 1263 in Table I1 were run to check the effect of the depressing agents used in flotation of the galena (sodium cyanide and zinc sulfate) upon subsequent flotation of sphalerite by diphenyl guanidine. Urea was substituted for potassium ethyl xanthate in tests 1253 and 1263 because it is a good collector for galena and a poor one for sphalerite, and the effect of the depressing agents is more marked with urea than with potassium ethyl xanthate. Test 1205 checks the effect of urea alone without any depressing agents when used for the flotation of galena. Table I1 shows that diphenyl guanidine as a collector for sphalerite is compatible with other flotation reagents used in floating galena. When the depressing agents sodium cyanide and zinc sulfate are used in the galena flotation step, the amount of lime in the sphalerite flotation must be increased (compare 1253 and 1263). Table I11 gives some of the compounds of guanidine which were tested and compared. Some of the compounds and derivatives of guanidine* are solu- * Diphenyl guanidine is in commercial production and is available on the market. ble in water and others are not. Those tested were fed dry. When an organic collector is promising, its compounds and derivatives should be tested and their comparative collecting power recorded. Eventually, in this way, it may be possible to discover some of the essential chemical characteristics of a good collector. For example, it is interesting to compare the diphenyl and dibutyl derivatives in Table IV with those of urea in Table 111, Example 3, U. S. Patent 2,664,198. All are good collectors. Table I shows some of the effects of lime on recovery of sphalerite by diphenyl guanidine. Table V

Jan 1, 1960

By W. B. Lilienthal

A considerable saving in time and money has been effected by use of a specially designed stainless steel container for laboratory drilling mud test work. This container involves use of a standard tall-form stainless steel beaker for service in which the mud sample is heated to an elevated temperature and maintained there for protracted periods of time, while undergoing agitation to facilitate mixing of mud components. Agitation is accomplished by rotating the filled containers on motor-driven rollers within an oven. Several porcelain balls are generally placed in the containers to further improve agitation. Soft glass containers (.Mason jars) were used in this service in early work, and were found to be unsuitable for the following reasons: 1. Poor resistance to thermal shock. 2. Containers could withstand only relatively low pressures. 3. Accidental breakage in handling. 4. Chemical deterioration and subsequent mud contamination from reaction of high pH muds with the glass at elevated temperatures. Pyrex containers were also considered, but, inasmuch as they provided improvement only in items 1 and 4 listed above the additional cost was not believed to be justified. A scale drawing of the container is shown in the figure illustrating details in cross-section. A pressed stainless steel lid was fabricated to match the rolled edge of the beaker

Jan 1, 1950

By E. P. Klier, Volker Weiss, George Sachs

IT has been shown that the isothermal transformation of austenite in a special steel can be modified by isothermal holding in the high subcritical transformation range.' Since this treatment potentially leads to increased hardenability, limited testing has been completed to determine if the stabilization effects observed with this treatment can be used to advantage in the heat-treating of 4340 steel. As an index of the effects of the several austenitizing treatments on the hardenability of the steel, Jominy-type hardenability tests were completed for specimens 2.5 in. in diameter and 8 in. long. Since the steel studied is to be used at strength levels where notch sensitivity is of major concern, notch sensitivity after selected austenitizing treatments has been evaluated by notch tensile tests for several specimen sizes. The steel composition and the austenitizing treatments are given in Table I. The test specimens are presented in Fig. 1. The hardenability data are given in Fig. 2 and the notch tensile properties are presented in Fig. 3. The hardenability of the steel investigated when determined by use of the standard Jominy test specimen2 as high and remained essentially unchanged for the different austenitizing treatments. For the larger test specimen, as has been shown by other investigations," the characteristic hardenability indexes are changed and it becomes possible to isolate austenitizing treatments which promote maximum hardenability. The stepped austenitizing treatment promotes higher hardenability as is indicated in Fig. 2. The evaluation of notch sensitivity for very high strength steels is best accomplished by means of the notch tensile test. The experimental conditions of the test, however, modify the notch strengths measured, and in the present experimentation an effort was made to achieve a limiting notch condition by fixing the notch root radius at 0.001 in. while the specimen diameter was allowed to increase from 0.3 to 1.1 in.* For this root radius the notch strength, 0.3-in.-diam specimen, and this trend differs from that for the larger specimens. At the highest tempering temperatures the 1.1-ip.-diam specimens yield comparable results for the austenitizing treatments compared. However, as the tempering temperature is progressively lowered below 800°F, em-

Jan 1, 1958

By E. Maxwell, C. J. Bechtoldt, H. C. Vacher

IN the course of an investigation of the properties of metals at low temperature there was occasion to determine the constitution of four iridium-osmium alloys. There is very little information in the literature1 on the constitution of synthetic Ir-0s alloys. Zvyagintzev' s has made a comprehensive study of different natural Ir-0s alloys and concludes that alloys containing more than 32 pct 0s have the close-packed hexagonal structure of osmium, whereas those containing less than 32 pct 0s have the face-centered cubic structure of iridium. The alloys studied in this work were prepared by the American Platinum Works, Newark, N. J., and were received in the form of fragments approximately 1.5 mm average diameter. The fragments had been obtained by crushing ingots made by fusing charges of iridium and osmium under an arc and air cooling. The ingots were not given a homogenizing heat treatment. Sample fragments Table I. Results of X-Roy Diffraction and Microscopic Examinations Phases Present as Determined by X-ray Diffraction Osmium Alloy Close- Iridium Face- Packed Centered Osmium, Iridium, Hexagonal Cubic Mlcro- WtPot Wt Pct Structure Structure scope 0 99.9 None Present 1 23.6 76.4 None Present 1 38.7 61.3 Present Present 2 59.4 40.6 Present Present 2 79.0 21.0 Present Not detected 2 99.9 0 Present None 1 Note: Chemical analyses of the iridium, osmium, and alloys were furnished by the American Platinum Works. of the iridium and osmium used in making the alloys also were included. Several fragments of each metal and alloy were examined microscopically and by X-ray diffraction. For the X-ray method the fragments were crushed further to pass a 270-mesh screen, then sealed in evacuated fused-silica tubes, heated to 1100°C for 18 hr, and allowed to cool in the furnace. Powder X-ray diffraction patterns were obtained from the annealed fragments by means of a Norelco camera having a diameter of 114 mm, and unfiltered cobaIt radiation. For the microscopic examination several fragments in the as-received condition were mounted in Melmac, (American Cyanamid Co.) and ground using the conventional series of abrasive papers. The polishing was done with 0-2 diamond abrasive on a Microcloth (Buehler Ltd.) lap, wet with xylene. After polishing, the surface was etched electrolytically in a 10 pct solution of chromic acid or in a 10 pct solution of potassium cyanide. Both reagents attacked the osmium-rich constituent, whereas the iridium constituent was attacked slightly by the chromic acid reagent and not noticeably by the potassium cyanide reagent. The results of the X-ray diffraction and microscopic examinations are summarized in Table I. Fig. 1 shows the microstructure of a 21 pct Ir-79 pct 0s alloy. The results indicate an appreciable solid-solu-bility range of osmium in iridium as was reported by Zvyagintzev.' The solid-solubility range of iridium in osmium is more restricted, apparently less than 21 pct Ir. This implies a large range of composition in which two phases can coexist that was not reported by Zvyagintzev.

Jan 1, 1955

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.' The damaging action of sulfur on the malleability of cobalt has not been generally recognized,'; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

By F. D. Rosi

IN the production of single crystals by the Bridg-man method of solidification from the melt in vacuum at a crucible lowering rate of 0.25 in. per hr, a cellular structure was frequently observed in copper and copper-base alloys at the terminal surface of the as-cast crystals (i.e., the surface representing the last portion of the crystal to solidify). The geometrical form of this structure varied from crystal to crystal, but, in general, could be classified as either hexagonal or quadrilateral. Fig. 1 shows examples of this cellular structure, which is similar to that reported by Buergerl and, more recently, by Pond and Kessler&apos; and Rutter and Chalmers. In the micrographs of Figs. lb and c, the cubic structure in the alloy crystals is obscured somewhat by excessive surface evaporation in the final stages of solidification. X-ray orientation studies indicate that the traces outlining the various geometrical forms correspond to octahedral planes, which are the planes of greatest reticular density in the face-centered cubic lattice. It would appear from this that the view first propounded by Bravais,4 that the surface energies and normal growth velocities of the different crystal planes are inversely proportional to their reticular densities, applies to this cellular structure, since those surviving are the planes of greatest atomic density. Thus, the observed variation in the geometrical form of this structure in crystals of different orientation is readily understandable from the distribution of the (111) planes in the standard {111}, (1101, and (1001 stereographic projections. Depending upon whether the crystal axis (i.e., the direction of crystallization) coincides with a <111>, <111>, or <100> direction, the cellular structure viewed from a surface perpendicular to the crystal axis will consist of a network of regular hexagons, skewed hexagons (with interfacial angles of 110" and 125"), or cubes, respectively. It follows, moreover, that off-orientations from these principal directions will yield modifications of these three basic geometric configurations. In this connection, it is interesting to note that the bounding planes of the hexagonal structure observed in tin by Rutter and Chalmers3 showed no preferred orientation.

Jan 1, 1954

By L. D. Jaffe

IN 1945-1946, the author measured temper brittle-ness in ingots of varying composition prepared by remelting SAE 3135 bar stock under vacuum. Since other investigators1-" have been referring to this hitherto unpublished work, belated publication seems worthwhile. Steel in 7 lb batches&apos; was induction melted with nickel additions in a magnesia crucible under a pressure of 10 microns of Hg or less and cast into a 2 in. diam chill mold. The compositions of ingots A, B, and C prepared in this way are shown in Table I; the vacuum melting lowered carbon, manganese, sulphur, and nitrogen content. Ingot B was homogenized 24 hr at 1095°C; ingots A and C were not homogenized. Blanks, M in. square, were cut from each ingot, austenitized 1 hr at 870°C, water quenched, tempered 1 hr at 595"C, and water quenched. Half the blanks from each ingot were given an embrittling treatment of 50 hr at 455°C and water quenched. A few specimens, embrittled and unembrittled, were finally heated 1 hr at 580°C and water quenched. Charpy specimens machined from the blanks were V-notched on the side closest to ingot mid-radius and paired as to radial position in the ingot, one of each pair having received the embrittling treatment and the other not. Specimens were broken in a standard impact machine at various temperatures, the same temperature, in general, being used for both bars of a pair. Fig. 1 shows the results. It is evident that temper brittleness, as measured by the increase in temperature of transition from brittle to tough failure introduced by the 455°C treatment, was decreased but not eliminated by reducing carbon to 0.006 pct, manganese to < 0.004 pct, and nitrogen to 0.001 pct. In another study," temper brittleness was apparently eliminated by -reducing carbon to 0.003 pct, with 0.80 pct Mn and 0.0015 pct N (ingot D)." • Analyses given for carbon below 0.02 pct were made by Jensen method; for nitrogen, by Kjehldahl method. Values quoted else-where&apos;-&apos;." for carbon content of ingot C and for nitrogen content of ingot D were obtained by conventional combustlon and by vacuum fusion methods, respectively, and are considered much less accurate. The 580°C final treatment removed previous em-brittlement (ingot B particularly), indicating that this was "reversible embrittlement."" Metallographic examination of ingot C with 1 pct nital etch revealed only ferrite; ingot A had carbide spheroids uniformly distributed in a ferrite matrix. With ethereal picric acid plus zephiran chloride etchant.&apos; no differences between embrittled and un- embrittled specimens of ingots A, B, or C were noted. Fracture of C and D below the transition temperature was predominantly transcrystalline, with traces of intercrystalline, in both embrittled and unembrittled conditions. The corresponding fracture of unembrittled B was mixed transcrystalline and intercrystalline; of embrittled B, predominantly intercrystalline with some transcrystalline areas. . . . Acknowledgment The efforts of J. C. Leschen, formerly of National Research CO~P., in preparing the ingots are acknowledged with thanks.

Jan 1, 1956

By Frank G. Miller, Ralph A. Seban

Problems relating to thermal methods of oil recovery have been given increasing attention during the past year. The nature of the physical and chemical processes underlying thermal recovery are not yet well understood. The need for pertinent basic information is recognized generally. One of the processes involved is the transfer of heat by conduction in oil reservoir rocks containing moving reservoir fluids. This technical note deals with heat conduction in a laboratory sand column filled with a moving hydrocarbon and therefore should be contributory to the presently inadequate fund of knowledge on thc over-all subject. In an analysis of the flow of vaporiziny propane through a horizontal column of sand, one of the present author9 demonstrated correspondence between thc measured values of pressure along the length of the column and those predicted by a theory which postulated that the enthalpy of the propane was invariable along the length of the column. This postulate way implied as a deduction from the principle of conservation of energy but the details of the deduction were not given. The specific purpose of this technical note is the presentation of these details both as an adjunct to the earlier analysis and to supply some additional details on the processes involved in this type of flow. Results disclose that rates of heat transfer by conduction, in the direction of fluid motion, generally would be small for systems of the type studied. FUNDARIENrAI. ENERGY EiQUAI-[ON The principle of conservation of energy may be applied to a section of the porous material on the basis that heat transfer, like fluid flow, is possible in the x direction only. Transfer of heat in the y and z di&apos;rections is prevented by suitable insulation or by taking the medium as infinite in directions perpendicular to the x axis. For steady state heat conduction and conditions of steady fluid flow the principle of conservation of energy specifies that any reduction in the enthalpy rate increases the flow of heat in the same proportion. Stated mathematically, dH KA 87 —- = - — - — U) * dx W dx........ Lvhere is the flow of heat in the positive x W dx direction. TEMPERATURE DISTRIBUTION IN DIRECTION OF FLOW The column of sand used in the previoi~sly described research is divisible into three different flow regimes. each of which may be analyzed independently. In the entrance region the liquid approaches the saturation state. A transition region is postulated following the transverse section at which the saturation state of the liquid is attained. In this transition region gas and liquid phases are both envisioned as present, with no vaporization occurring and with fluid movement restricted to the liquid. The upstream end of the exit region is at the transverse section of the column where the fraction of the pore space occupied by gas first becomes great enough for gas flow and where vaporization of the liquid begins. Fig. 1 indicates schematicaHy the thermodynamic processes undergone hv the fluid in the three flow regimes.

Jan 1, 1956

By J. S. Brown, A. G. Guy

With the exception of the work of Tammann and Hartmann,1 no published information has been found on the structural changes produced in eutectic structures as the result of heating following plastic deformation. In part this lack of information may be due to the fact that many eutectic structures contain an intermetallic compound as a prominent phase, and as a consequence have been considered to be unworkable. For example, Tammann and Hartmann were able to obtain useful data only on those alloys that they could greatly reduce in thickness by cold rolling. This restriction placed on the investigation of alloys containing intermetallic compounds has been largely removed by the work of Savitskii2 which showed that large deformations of such alloys can be produced by relatively slow compression at temperatures near the melting range. It was possible, therefore, to carry out the present work on a range of binary eutectics including one composed of two intermetallic compounds. The essential results obtained on the alloy systems studied are illustrated by the Pb-Mg eutectic containing 33.2 pct Mg, Fig 1. The cast structure, Fig la, was obtained by melting together magnesium of 99.8 pct purity and chemically pure test lead, casting into a heated, small steel mold, and furnace cooling in the mold from about the eutectic temperature. The fairly coarse eutectic structure thus obtained was too brittle to work at room temperature without cracking. Fig 16 shows the worked structure obtained by compressing a 1/2-in. cube 70 pct in about 15 sec at 550°F and then water quenching. The pronounced changes in the distribution of the two phases produced by heating the worked alloy at 850°F for 1 hr are shown in Fig lc. Recrystallization of both phases appears to have taken place, and the mechanical properties of the cast alloy must have been significantly changed by the working and heat treatment. Similar results were obtained with the Mg-59.5 pet Bi, Mg-36.4 pet Sn, Mg-65.4 pet Cu, and Bi-40 pet Cd eutectics, only the last of which could be worked at room temperature. Tammann and Hartmann reported a thickening and shortening of the needles of the eutectics which they heated about 10°C below the melting range for 1 hr after drastic cold rolling. They found the following eutectics, given the indicated amounts of reduc- tion, to have a granular structure after heat treatment: Sn-9 pet Zn (98 pet); Cd-82.5 pet Pb (60 pet); and Bi-43.5 pet Pb (90 pet). On the other hand the alloy Al-11.7 pet Si (60 pet) showed no change after heating. Tammann and Hartmann observed a distinct shrinking of the needles in unworked eutectics subjected to heat-treatment. In the present work inappreciable change in the eutectic structure was found on heating undeformed alloys. In summary, it appears that eutectic structures can be recrystallized into a "spheroidized" condition by heating near the eutectic temperature after severe deformation. If the eutectic contains one or more brittle phases the necessary deformation can be accomplished by pressing at high temperatures. It is reasonable to expect that this tendency towards equiaxed grains from the plate- or needle-like eutectic structure should be general since the energy relations and mode of growth in recrystallization are so different from those that hold for eutectic crystallization. References 1. G. Tammann and H. Hartmann: Ztsch. Melallkunde (1937) 29, 141-144. 2. E. M. Savitskii: Doklady Akad. Nauk S.S.S.R. (1940) 62, 349-351. Abstr. in Melal Prog. (July, 1949) 56, 126, 128.

Jan 1, 1950

By R. F. Mehl, J. T. Ransom

For many years the Metals Research Laboratory of Carnegie Institute of Technology has been concerned with the statistical nature of the engineering properties of steel from an experimental viewpoint, particularly those properties representing ductility.&apos; In the past three years new work has been directed toward evaluating the statistical nature of the endurance properties. It has been shown that both the fracture curve and the endurance limit in fatigue are markedly statistical in nature. The S-N curve (and the endurance limit) of ferrous materials is often determined with specimens which number as few as ten. The common procedure is to test the first specimen at a stress well above the expected endurance hmit. Each succeeding specimen is then tested at a progressively lower stress, until, after five or six tests, a specimen runs ten million or so cycles without failing. Two or three more specimens are then used to find the highest stress at which failure will not occur; the limiting stress determined in this way is called the endurance limit. It has now been found, however, that the variability in the fracture curve and in the endurance limit in heat-treated alloy forging steels is so great that S-N curves must be drawn on the basis of distribution curves which can be appraised only by statistical methods. Two methods have been adopted in this study: (1) straightforward statistical studies of cycles to fracture of a number of specimens at each of a series of stress levels, and (2) a new abbreviated statistical method, known as "staircase testing."2 The latter corisists in testing a series of specimens, one by one, with the test stress for any given specimen automatically

Jan 1, 1950

By Gearge C. Wallick

This paper describes experimental procedures for the calibration of capillary tubes to be employed as comparison standards in gas flow-rate measurements and considers several types of flow which were observed in the calibration of seven capillaries of varying diameter. It is shown that under certain experimental conditions deviations from Poiseuille flow are observed which may not be attributed to turbulence, and that this flow behavior may be described empirically by introducing the classical kinetic energy correction into the Poiseuille equation. INTRODUCTION Techniques have been developed for the measurement of the volume rate of flow of nitrogen through glass capillary tubes as a function both of the differential pressure applied and of the absolute gas pressure. Capillary tubes thus calibrated are frequently used to determine the rate of gas flow through a porous sample in the measurement of slip-corrected permeability. The purpose of this note is to describe the calibration procedure and to discuss some observed deviations from the ideal flow behavior predicted by the Poiseuille equation. EXPERIMENTAL PROCEDURE The volume flow rate of nitrogen as a function of the differential pressure was determined experimentally for a series of seven glass capillary tubes of varying diameter. As is shown in Table 1, the capillary radii in the series ranged from 0.004 cm for K1 to 0.07 cm for K7. The capillary tubes were cut from capillary tubing purchased on special order from several manufacturers and the bore radii were determined by microscopic measurement. The gas volume flow rate was measured for each capillary tube at a series of differential pressures in the range from 0 to 3 cm of mercury and at average absolute pressures of 1.0, 2.5, 4.0, and 6.0 atm. Experimental Procedure for Small Capillaries A schematic diagram of the apparatus used to calibrate the three smallest capillaries, Kl, K2, and K3, is shown in Fig. 1. By means of a standard Ruska Instrument Corp. volumetric pump (equipped with a synchronous motor drive, two stages of gear reduction, and a quick-change lathe gear box), nitrogen was displaced by mercury from a metal cell immersed in a constant-temperature bath. The pump, the line to the cell, and a part of the cell were filled with mercury. As mercury was forced into the cell, it displaced nitrogen which passed through the capillary tube being calibrated and into a large container with a volume of approximately 30 liters. Since the volume of this container was very large compared to the total volume change of the gas resulting from the action of the displacement pump, the absolute pressure of the system was essentially constant throughout any one run. Prior to any determination this pressure could be set at any desired level by means of an auxiliary nitrogen cylinder. The differential pressure across the capillary was measured with a Meriam Red Oil manometer and recorded together with the corresponding pump displacement rate which was equal to the gas flow rate. By repeating this process for a series of different displacement rates at each of the absolute pressures of interest, the data necessary for plotting the calibration curves for capillaries K1, K2, and K3 were obtained. All calibration measurements were made in a constant temperature room to minimize errors due to temperature fluctuations. In each run. the flow was maintained until equilibrium was established. Experimental Procedures for Large Capillaries The flow rates through Capillaries K4, K5, K6, and K7 required to obtain the pressure drops desired were larger than could be obtained from available constant displacement pumps, and it was thus necessary to employ an alternative calibration procedure. The arrangement of apparatus used in calibrating these capillaries at an average pressure of one atmosphere is shown in Fig. 2. Each capillary was calibrated by flowing nitrogen through the capillary and recording the differential pressure as a function of the flow rate. &apos;The differential pressure was measured with a Meriam Red Oil manometer and the flow rate was determined by collecting the effluent gas over water at constant pressure and recording the increase in volume per unit time after an equilibrium had been established. Appropriate corrections were made for the

Jan 1, 1953

By William H. Hartwig

A paper by Rose1 has called attention to some of the problems of wetting-liquid relative permeability measurement. The premises and conclusions set forth by Rose, namely the applicability of the Hassler scheme of measurement, will be accepted. In addition, it will be concluded that certain electrical analog circuits can be used as a pattern for consideration of possible hydraulic systems of measurements. NEW SCHEME OF MEASUREMENT The object of this note is to propose a new scheme of wetting liquid relative permeability measurement. It is significantly different from those heretofore described, nonetheless it is based on Hassler concepts. The scheme is illustrated in Fig. 1 in terms of the corresponding electric circuit analog. It may be designated descriptively as the "comparison" method of wetting-liquid relative permeability measurement. In this circuit, R, represents the resistance of the core sample which is being studied for relative permeability characteristics, R represents a "standard" resistance, R represents the combined series resistance of the barrier pads, R R2 represent the combined series resistance of barrier pads in the manometer circuit, C, C represent the capacitance of the manometers, E is a constant voltage source, S is the switch or stopcock. The following conditions are imposed upon .the network: Rb » R, and R, R,» R, R, » R., and the condensers C, and C,

Jan 1, 1953

By M. J. Sinnott

WITH the advent of nodular iron as an engineering material, considerable interest has been shown in developing this material for various applications. Generally the strength, hardness, or ductility are the more common properties used for design purposes but occasionally applications involving a knowledge of the thermal conductivity of the material is required. A search of the literature showed, rather surprisingly, that relatively little work has been done on this property for all types of cast iron. Insufficient data are available on thermal and electrical conductivities to develop the Weidemann-Franz ratio, or the Lorentz relationship, for estimation purposes. There are no data on nodular irons and the published data on malleable irons are quite sketchy. For these reasons the conductivity of the group of nodular irons listed in Table I were measured. Irons I to IV were made in such a fashion as to maintain the carbon and alloy content essentially the same while varying the silicon content. Test specimens were cut from the mid-section of 4-in. keel castings. Iron V is a commercial casting of nodular iron. The test specimen of this iron was cut from the center of a large cast billet 3x10x26 in. All alloys were tested in the as-cast condition. A microstructural examination showed that each iron had spheroidal graphite but the size and distribution varied with the silicon content of the iron. The spheroid size decreased while the number of graphite nodules increased as the silicon content of the iron was increased. The matrix structures of each iron consisted of pearlite and ferrite with the proportions varying from predominantly pearlite in the low-silicon iron to mostly ferrite in the high-silicon iron. The commercial heat, iron V, was predominantly pearlite probably because of its higher manganese and phosphorus content. Two methods for measuring the thermal conductivity were used. The first was a modification of the techniques described by Powell and Hickman and Van Dusen and Shelton,² the second method was a simpler technique described by Jakob and Hawkins." Since the agreement of both methods as tested on two sets of duplicate samples was excellent, the simpler experimental technique was used. The results of the measurements are given in Table II along with a summary of the microstructural constituents. These conductivity data indicate that as the percentage of silicon increases there is a corresponding decrease in the thermal conductivity even though the structure is changing from pearlitic to ferritic. Such a change in microstructure is usually accompanied by an increase in conductivity. A third factor involved in the behavior of these irons is the size and distribution of the graphite nodules. The relative amounts of graphite do not change greatly but the size and distribution do. Generally graphite improves the conductivity but in the present case such an effect is probably masked by the alloying effect from the silicon and its dispersion through the matrix. The thermal conductivity of the nodular irons studied is less than that of regular foundry irons by some 10 to 30 pct and is less than that of regular malleable irons.&apos; The cause of the decreased conductivity is probably the more highly alloyed fer-rites obtained in these irons and the changed mode of distribution of the graphite as compared to the regular foundry irons. References R. W. Powell and M. J. Hickman: Journal Iron and Steel Inst. (1946) 154, No. 2, p. 99. &apos;M. S. Van Dusen and S. M. Shelton: U. S. Bur. Standards Journal of Research, RP668 (1934) 12, p. 429. ³M. Jakob and G. A. Hawkins: Elements of Heat Transfer and Insulation. 2nd Ed. (1950) New York. John Wiley and Sons. &apos; J. W. Donaldson: Journal Iron and Steel Inst. (1933) 128, No. 2, p. 255.

Jan 1, 1954

By G. J. Wolga, W. W. Tyler, A. C. Wilson

THE physical properties of uranium have been reviewed by Katz and Rabinowitch.1 Their review includes thermal conductivity data for ternperatures above 375°K. Recently, Mendelssohn and Rosenberg&apos; have published data on the thermal conductivity of uranium from 2" to 20°K. Our measuremerits indicate the temperature dependence of the thermal conductivity in the temperature interval from 20" to 300°K. Electrical resistivity and thermoelectric power were measured on the same sample. The material studied was normal uranium which had been heated at 700°C in a lead bath for 10 min and then quenched in a water bath held at 50°C. From this material a rod M in. in diameter and 2 1/2 in. long was machined. Two 0.040 in. holes were drilled into the rod 1 3/4 in. apart. Copper-constantan thermocouples for temperature and potential measurements were soldered to copper pins which were pressed tightly into these holes. Details of the equipment and experimental techniques used in making the measurements have been described elsewhere." Fig. 1 shows micrographs of a section of the sample studied. Fig. la was taken with unpolarized light and shows impurity inclusions, probably uranium carbide. Fig. lb, showing the same field, was taken with polarized light and gives some indication of the grain size and twinning within the grains. Experimental Results Thermal conductivity and electrical resistivity data are shown in Fig. 2. Table I shows values of

Jan 1, 1954

By H. Margolin, E. Ence

Two versions of the Ti-Mn binary diagram have been published recently.&apos; , -0th diagrams show two compounds in the region between 40 and 70 wt pct Mn, but disagree as to the reaction in which these compounds are involved. The investigation of the manganese-rich portion of the Ti-Mn binary diagram was undertaken at New York University as part of an investigation of ternary systems with titanium and manganese in order to determine which of the proposed diagrams is correct. A number of alloys between 31 and 70 pct Mn were prepared in a manner similar to that described by Cadoff and Nielsen; except that low currents (110 amp in argon atmosphere) and long melting times (up to 20 min) were used to prepare the alloys. Compositions were determined from weight-loss data, assuming all loss as due to manganese. Heat treatments were carried out with relatively large pieces, since there was a tendency for manganese to be lost during heat treatment. When X-ray diffraction data was to be obtained, the central parts of heat-treated specimens were used to make filings or powders which were not heat treated. Specimens were heat treated from the as-cast state. Heat-treatment times were as follows: 1150°C, 1 day; ll00°C, 2 days; 1000°C, 5 days; and 900°C, 15 days. It should be noted that equilibrium was not attained at 900°, 1000°, and in one case, at 1150°C. Metallographic specimens were electrolytically polished and strain etched by a technique described elsewhere.&apos; At least four, and possibly six, phases were found in the region investigated. On the basis of information available at this time, a completely self-consistent diagram cannot be constructed, and therefore data are presented only for those phases which have been identified by both X-ray and microstruc-ture. Of the compounds detected, the one highest in manganese is the Laves phase, TiMn,, which is hexagonal with a MgZn, type of structure.V he diffraction data for TiMn2 from a 70 pct Mn alloy annealed at 1150°C are shown in Table I. The c/a ratio and parameters of TiMn2 agree well with those of Wall-baum hnd Rostoker et al. The values obtained here are c/a = 1.641, a = 4.825A. Another compound is the y-phase which is estimated to contain about 60 pct Mn. The y-phase has a structure which is identical to that of TiMn, with c/a = 1.639, a = 4.906Å. The fact that y has a Laves-type lattice would suggest that TiMn, has a range of solubility which extends from the composition of TiMn2 (69.6 Mn) to that of y (60 pct Mn). However, this could not account for microstructures which, in the 60 to 70 pct Mn region, show several phases in both the as-cast state and after annealing at 1150°C. Fig. 1 shows a two-phase structure of a 60 pct Mn alloy annealed at 1150°C. The phases present are y (white) and e (dark). If y were TiMn, then, according to Rostoker et al.,&apos; the second phase of Fig. 1 should be P-Ti. The diffraction data for the 60 pct Mn alloy of Fig. 1 are shown in Table I. The starred d-values are from the e-phase and these lines do not correspond to those of &Ti. Comparison of as-cast and 1150°C microstructures of the 60 pct Mn alloy indicates that e precipitated from y. Since y has a

Jan 1, 1955

By G. H. Miller

With the recent advances which have been made in science and technology and the increased use of mathematics in this area, the question of the best mathematics courses for a mining engineer to take is of major importance. The question becomes even more difficult to answer due to the recent increase in the number of different mathematics courses in the last two decades offered by the mathematics departments. Therefore, the National Study of Mathematics Requirements for Scientists and Engineers (NSMRSE) was designed to provide some answers to these questions. Approximately 10,000 scientists and engineers were selected for the Study, These individuals were placed in two categories: (1) The Awards Group, recipients of national honors or awards and those recommended by the members of the Board of Advisors as having national and international reputations in their areas of specialization and (2) The Abstracts Group, persons exceptionally productive in their research, based on the number of journal articles listed in the last five years in the Engineering Index, Scientific and Technological Aerospace Reports, Chemical Abstracts, Biological Abstracts, and the Physics Abstracts. The NSMRSE Course Recommendation Form and the Instruction and Course Content Sheet were constructed with the aid of the Board of Advisors and other consultants. For the Study, 40 courses were selected by the mathematical consultants. In order to make sure that the basic content of the mathematics courses was the same for all respondents, a brief resume of each of the 40 courses was given. The NSMRSE Course Recommendation Form consisted of seven sections. These sections were as follows: Section 1, 38 different specializations; Section 2, orientation of work (applied through theoretical); Section 3, highest degree obtained; Section 4, place of employment (academic, nonacademic); Section 5, administrative capacity (administrative or nonadministrative); Section 6, age groups (five-year intervals). Section 7 contained the 40 courses which were to be marked according to five categories: (1) Course Length, 3 to 36 weeks; (2) Applied-Theoretical Orientation, a five-point scale; (3) Course Level, freshman through graduate; (4) Knowledge of Course; and (5) Use of Course Content in Work. The Analysis The report of the data is based on the replies received from 44 mining engineers. This group was part of the Awards and Abstracts Group for all engineers. The resume of the recommended courses is reported in quintiles (upper fifth to lower fifth), since recommendations of this kind are not precise. The results of the Study are based on recommendations of the most active research men in engineering in the U.S. today; therefore, the reader should realize that these course recommendations represent an upper bound of mathematics requirements for the Ph.D. in both undergraduate and graduate work. Conclusions and Recommendations 1) Mining engineering students who plan to be active research specialists should take all those courses which are "very highly recommended" (80-10070) and "highly recommended" (60-79.9%). Those courses in the upper two quintiles and recommended by most mining engineers are: first-year calculus, third-semester calculus, elementary differential equations, applied statistics, and machine computation. Courses of "moderate recommendation" (40-59.9%) are: vectors, intermediate ordinary differential equations, the first course in partial differential equations, elementary probability, and linear programming. 2) The great majority of mining engineers indicated that they prefer a course which is concerned primarily with applications. Only the standard courses such as first-year college mathematics, calculus, differential equations, and advanced calculus received a recommendation for 50% theory and 50% practice. Therefore, all mathematics courses given to mining engineers should contain many applications and little theory. Engineers in both the applied and the combination (ap-plied-theoretical) groups indicated a definite need for applications in all courses. 3) In general, recommendations were for mathematics courses to be given for short intervals of time such as 3, 6, or 12 weeks. Only the standard courses mentioned previously received the usual one-semester or one-year recommendation. Therefore, it is of value to combine several related courses into a one or two-semester course so that the mining engineering student could acquire important mathematical knowledge at an early date in order to prepare him for his research. 4) There was little use for the newer courses in modern mathematics such as the functional analysis sequence, the modern algebra sequence, and the group theory sequence. In addition, there were uniformly very low recommendations (0-19.9%) for multilinear algebra, complex variables, mathematical logic, special functions, integral equations, approximation theory, analytic mechanics, integral transforms, and geometric algebra. Therefore, these courses should be given a low priority. 5a) Comparisons among mining engineers with different backgrounds showed that the combination ap-plied-theoretical group recommended more mathematics than the applied group. 5b) There was little difference in recommendations between the administrative group and the nonadminis-trative group. 5c) Analysis of age groups showed that those in the lower age groups gave significantly higher recommendations to courses such as the first course in partial dif-

Jan 1, 1971