Search Documents

By D. W. Lillie

It has been demonstrated that considerable bend ductility exists in bulk specimens of polycrystalline high-purity silicon. The possibility of hot-forming at 1200°C is suggested. EXCELLENT corrosion resistance in many media and low cross section for absorption of thermal neutrons (0.13 barn) would make silicon of interest to nuclear engineers were it not for extreme brittle-ness and the difficulty of fabrication by any reasonable means. The use of silicon for structural purposes also has been considered in view of its light weight and oxidation resistance. Johnson and Han-sen' have investigated the properties of silicon-base alloys and concluded that there was no way of making pure silicon or silicon-rich alloys ductile at room temperature. In view of reports of appreciable ductility in germanium single crystals above 550°C'." and some plastic deformation in single-crystal silicon above 900oC,' the present investigation was undertaken to define more precisely the limits of high-temperature ductility in pure silicon. After this investigation was begun torsion ductility in both germanium and silicon was reported by Greiner." Through the courtesy of F. H. Horn, a small bar of cast extra high-purity silicon was obtained and small bend specimens were made from it by careful machining and grinding. All of the reported tests results were obtained from samples from this bar (bar No. 1) and one other of similar source (bar No. 2). No complete analysis was obtained but, based on analysis of similar semi-conductor grade material, metallic impurities were under 0.01 pct total. Vacuum-fusion analysis for oxygen showed a value of 0.0018 2 0.0003 pct for the first bar tested and metallographic analysis showed no evidence of a second phase. Bend tests were carried out on an Instron tensile machine using a bend fixture with a 1 -in. span loaded at the center. Supporting and loading bars were 0.250 in. round and the load was applied by downward motion of the pulling crosshead of the machine. Specimen thickness and width were approximately 0.10 in. and % in. respectively. Loading rate was controlled by holding crosshead motion constant at 0.02 ipm. In some cases a smaller specimen was used on a 5/8-in. span with a 0.129-in.-diam loading bar. The entire bend fixture was surrounded by a hinged furnace and all heating was done in air atmosphere. Temperature measurement was made with thermocouples fastened directly to the bend fixture within less than 1 in. from the specimen. Autographic stress-strain curves were recorded during each test, and breaking load, total deflection, and plastic strain could be obtained from these curves. Stress was calculated from the beam formula S = 3PL/2bh2, where P is the load in pounds, L the span in inches, b the specimen width in inches, and h the specimen thickness in inches. This formula is strictly correct only in the elastic range but has been used to calculate a nominal stress for convenience in the plastic range. The stress given is the maximum stress in the specimen. Results The results of the complete series of tests are shown in Table I. The first group of tests (specimens Nos. 1-6) showed the beginning of plastic flow at a test temperature of 900°C, so two additional tests (Nos. 8 and 9) were made at 950°C on small-size specimens from bar No. 2. Specimen No. 8 was tested in the as-machined condition, and No. 9 was heat-treated in hydrogen at 1300°C for 2 hr, cooled to 1200°C and held 1 hr, cooled to 1000°C and held 1 hr, cooled to 900°C and held 1 hr, and finally cooled to a low temperature before removal from the hydrogen. It is apparent that the heat-treatment had a significant effect on yield strength and ductility. In addition, the magnitude of the yield point was conslderably reduced in the heat-treated specimen as is shown m Fig. 1 by tracings of the stress-strain curves. After obtaining a furnace capable of reaching higher temperatures specimens Nos. 10 to 13 were tested at 1100 and 1200°C. Strain rate was increased by up to a factor of 10 to see whether the ductility observed was excessively strain sensitive. Specimen NO. 10, strained at 0.02 ipm and 1100oC, was still bending at a deflection of 0.322 in. when the load rate was increased to 0.2 ipm, resulting in immediate

Jan 1, 1959

By A. J. Griest, P. D. Frost, H. A. Robinson

The flow characteristics and uniform elongation of alpha-beta titanium alloys in the solution-treated condition were shown to be markedly affected by the solution temperature. Two classes of alpha-beta alloys were distinguished, based on the effect of solution temperature on the uniform elongation. Martensitic alpha-beta alloys, which are relatively weakly beta-stabilized, showed decreasing values of uniform elongation as the solution temperature was initially increased. However, after solution-treatment at still higher temperatures in the alpha-beta field, the uniform elongation of these alloys was again high, and often attained its maximum value. Nonmartensitic alpha-beta alloys, which are more heavily beta-stabilized, showed a continuous decrease of uniform elongation with increasing solution temperature. The behavior was rationalized in terms of the alpha-beta ratio and the alloy content of the beta existing at the solution temperature. The data indicate that in commercial practice close temperature control may be required to get maximum uniform elongotion, and hence, maximum potential formability, in solution-treated sheet. Bend-test data also were obtained for the solution-treated conditions. A MOST important objective of current titanium research is the development of age-hardenable alloys with superior formability in the solution -treated condition. Alpha-beta titanium alloys have been shown to be amenable to high-strength aging treatments after solution-treatment in the alpha-beta field.' However, heat-treatment data on the properties of solution-treated sheet, such as uniform elongation, minimum bend radius, and flow properties, which have a bearing on the potential formability, have not been widely available. This paper presents only the most significant results of a research program conducted at Battelle for the Air Force in an effort to develop sheet alloys that can be formed readily as solution-treated and subsequently aged to very high strengths. Data for 10 compositions representative of the more than 25 alloys studied in this program are presented. A primary objective of the paper is to demonstrate the pronounced dependence of the flow characteristics and uniform elongation on solution-treatment temperature. This effect is believed to be vitally important in the commercial heat-treatment of age-hardenable titanium sheet alloys. Experimental Procedures Melting and Fabrication—The nominal and actual compositions, beta transi temperatures, and rolling temperatures of 10 of the 30 alloys studied are presented in Table I. Stock :€or two of the alloys, E (Ti- 8Mn) and J (Ti-6A1-4V) was obtained from commercial heats. The remaining heats, except D and I, were double melted as 10-lb heats in a consumable-electrode furnace. Melting stock was 120 Brine11 hardness sponge. The oxygen and hydrogen analyses spotted throughout the heats indicate the range of interstitial levels resulting from the melting practice used. Heats D and I were melted as 20-lb ingots with the same grade of sponge. These ingots were cut in half and one portion used in the present evaluation. The ingots, which were about 4 in. diam and 4 in. in height, were upset forged and drawn at 1750°F to sheet bar 5/8 in. thick by 2 1/2 in. wide in such a manner that the top of the ingot corresponded to the top of the sheet bar. Slabs of the sheet bar, 5 1/2 in. in length were scalped to 1/2 in. thickness and rolled at the temperatures indicated in Table I to approximately 0.055 in. sheet. Elongation during rolling took place at 90" to the original forged length. The fabrication procedure used is described in some detail since the experimental heats showed considerable directionality in mechanical properties. The rolling procedures for the commercial heats were unknown, but were such as to produce essentially isotropic properties. All heats, as rolled, showed microstructures typical of alpha-beta alloys worked in the alpha-beta field; that is, the structures consisted of equiaxed alpha particles in a beta matrix. Heat Treatment— The effects of solution and aging heat-treatments on the properties of the alloys were evaluated uSing longitudinal and transverse tensile and bend coupons sheared from the sheet. Two or three solution-treated conditions were evaluated for each alloy. In addition, the alloys were also tested after annealing at 1200°F for 4 hr and furnace cooling. The solution-treated and annealed conditions were those in which the alloys might be expected to

Jan 1, 1959

By C. Feng, C. Elbaum

Knoop hardness measurements were carried out on large grains of iodide titanium containing different amounts of oxygen. For each oxygen content the hardness is recorded ainingas a function of the crystal orientation and of the angle 4 between the indenter diagonal and the projection of the C (hexad) axis in the surface. The results can be expressed by the following relation; hardness = n-k cos 2ø, where n and k are constants for a given oxygen content and crystal surface orientation. A NISOTROPY of hardness is a well-known phe-nomenon and has been reported for many metals.1-3 At the present time, however, such information is not available in the literature for titanium. Consequently, a systematic study of the simultaneous effects of oxygen content and crystallographic orientation on the hardness of titanium was undertaken in this laboratory. Evaluations of oxygen content in titanium are frequently carried out through hardness tests. Although such procedures may be justified in small grain specimens, the results of the present investigation indicate that the anisotropy of hardness should be taken into account in the case of coarsegrained specimens as well as in the case of pronounced preferred orientation. Materials and Experimental Procedures Iodide titanium, 99.99 pet pure and containing of the order of 0.002 wt pet O, was used throughout this investigation. The metal was arc melted in an argon atmosphere and cold rolled into strips 1/16 in. thick. These strips were subsequently recrystal-lized and strain annealed in vacuum (10" mm Hg or better) at 850°C in order to produce crystals varying in diameter from 10 to 25 mm. Oxygen was introduced into selected large crystals by heating at 700°C in an atmosphere of pure oxygen under an observed pressure of approximately 50 mm Hg. Each sample was subsequently annealed in vacuum at 850°C for 100 hr, in order to homogenize the oxygen content throughout the specimen. It was found that longer annealing was not necessary, for no change of surface hardness in a given direction was detected after prolonged annealing. The oxygen content was determined by the difference in weight of the specimens before and after the oxidation-annealing cycle. The accuracy of oxygen determination is within ±0.1 mg in samples weighing 0.5 to 1 g. A vacuum fusion analysis of oxygen was performed on several samples and gave results in good agreement with the ones obtained by the weight change. It should be emphasized that expected weight losses through evaporation of the metal in vacuum at 850°C' are many orders of magnitude lower than the precision of these measurements. Following the annealing treatment, both oxidized and unoxidized crystals were carefully polished. All detectable traces of surface cold working were removed by repeated polishing and etching. Laue back reflection X-ray patterns were taken for each crystal for the purpose of determining the orientation and ascertaining the absence of substructures detectable by this method. Hardness measurements, using a 1 kg load, were subsequently carried out on a Tukon hardness tester equipped with a Knoop indenter. The Knoop indenter was used throughout this work because indentations obtained by means of a Vickers indenter are considerably distorted due to the anisotropy of the elastic constants in titanium. Such distortions are much less pronounced in the case of Knoop indentations, although for some orientations a cer-

Jan 1, 1959

By W. M. Parris, P. D. Frost, H. A. Robinson

The effects of hydrogen content and strain rate on the static tensile and notch-rupture properties of the Ti-3Mn-complex alloy heat-treated to differed strength levels were investigated. The extent of embriulement was found to be proportional to the amount of hydrogen present and the strength to which the specimens were heat-treated. The research suggests the possible necessity of specifying lower hydrogen limits than are now allowed when titanium alloys are heat-treated to higher strengths than are presently used. The research also supports a hypothesis advanced earlier for a mechanism of hydrogen embrittlement. MUCH attention has been focused on the effects of hydrogen in in Most of the published in- formation has dealt with the effects of hydrogen on alloys in the annealed or lowest-strength condition. The work of Kotfila and Erbin3 is one of the few exceptions. In view of the fact that heat-treatments are now being used to produce high strength in titanium alloys,' it is necessary that more attention be given to the effects of hydrogen on these alloys in the heat-treated condition. Research was initiated to establish the effects of hydrogen on the properties of the Ti-3Mn-complex alloy at various strength levels. This research, which supplemented that of Kotfila and Erbin, was started because it was found that high-strength tensile specimens of this alloy were strain-rate sensitive. The essential results of the research are summarized in this paper. MATERIALS AND EXPERIMENTAL PROCEDURES Material for this investigation was a 41/2-in.-diam bar forged from a single commercial heat of the Ti-3Mn-complex alloy having the composition given in Table I. The as-received forging was reduced further by forging at 1750°F to 3/4-in. square bars. About one fourth of this material was vacuum annealed at 1400°F for 24 hr to obtain a base hydrogen content of 25 ppm. The remaining bars were hydrogenated to levels of 90, 140, and 260 ppm in a large Sievert's apparatus in the following manner: Four 3/4-in. square bars, 5 in. long, were placed in the reaction chambzr. The chamber was evacuated, heated to 1400°F, and a measured amount of hydrogen was introduced. When absorbtion was complete, as indicated by the drop in pressure, the reaction tube was cooled and the bars removed. Each batch of bars was then sealed in individual evacuated Vycor containers and heated for 24 hr at 1400°F in order to distribute the hydrogen homogeneously. After vacuum-annealing or hydroge nation, the bars were rolled at a temperature (1400°F) below the ß-transus to 1/2 - in. - diam rounds. Groups of the rolled specimens representing each of the hydrogen levels were given the following heat-treatments: 1) One hr at 1300°F, water-quenched. 2) One hr at 1300°F, water-quenched, and aged 8 hr at 1100°F. 3) One hr at 1300°F, water-quenched, and aged 4 hr at 1000°F. 4) One hr at 1300°F, water-quenched, and aged 48hr at 800°F. Heat-treated bars were machined into standard 0.250-in.-diam tensile specimens having 1-in. gage lengths. Throughout the processing and testing of this material, hydrogen analyses were made by vacuum-fusion methods to check for accuracy of hydrogen additions, homogeneity, and possible losses during processing. A summary of these analyses is given in Table II It may be seen that the actual hydrogen contents were reasonably close to the desired levels. In addition, it was noted that the variation in hydrogen content within any one bar did not exceed

Jan 1, 1959

By W. S. Hyler, L. W. Berger, R. I. Jaffee

Hydrogen additions of 390 ppm to A-55 titanium and 368 ppm to Ti-8 pet Mn have no deleterious Hydrogenadditionseffect on the unnotched and notched rotating-beam fatigue properties of these materials. 'These amounts of hydrogen, however, are sufficient to cause severe notch-impact thesematerials.embrittlement in A-55 titanium and pronounced loss of tensile ductility in Ti-8 pet Mn. The lack of embrittling effect in fatigue in the latter alloy is consistent with the postulated strain-aging mechanism of hydrogen embrittlement in a-ß alloys. There is a significant strain-agingincrease in the unnotched endurance limit of A-55 titanium with the addition of hydrogen. This increase may be explained as the result of internal heating effects which would dissolve the hydride and cause solid-solution strengthening. TITANIUM and its alloys may be seriously embrittled by relatively small amounts of hydrogen. The form which this embrittlement takes has been shown to vary with alloy type. The a alloys, for example, suffer most strongly from loss of notch-bend impact toughness' when sufficient hydrogen is added, and this effect has generally been associated with the presence of hydride phase in the micro-structure. In a-ß alloys, on the other hand, hydrogen is most detrimental to tensile ductility in slow-speed tests,2-1 and the embrittlement may be detected in a most convincing manner by means of rupture tests at room temperature. This particular kind of embrittlement has not been associated with a change in microstructure, but has been classified rather generally as associated with a strain-aging type of mechanism.' In the present paper, the effect of an embrittling amount of hydrogen on the rotating-beam fatigue properties of both an a and an a-ß titanium alloy is covered. For this study, annealed commercially pure (A-55) titanium was chosen as an a alloy, and equilibrated and stabilized Ti-8 pet Mn as representative of a typical a-ß alloy. Nominal hydrogen levels of 20 and 400 ppm were evaluated, the latter amount having been shown previously to be severely detrimental to the impact toughness of commercially pure titanium and to cause pronounced strain-aging embrittlement in the Ti-8 pet Mn alloy. The only report of the effect of hydrogen on the fatigue properties of titanium is given by Anderson et al.,° in which a push-pull type of fatigue test was conducted on as-received commercial-purity titanium sheet. Much scatter was found in the results, but generally the presence of hydrides slightly decreased the fatigue strength of unnotched specimens in the longitudinal direction. The results of notched tests were masked too greatly by scatter to be significant. Experimental Procedure Preparation of Materials—Analyses of the A-55 titanium and the Ti-8 pet Mn alloy used in this investigation are given in Table I, which indicates the 8 pet Mn alloy to be more nearly a 6 pet Mn alloy. This alloy will be referred to as Ti-8 pet Mn, however, since this is the commercially designated composition. Both alloys were received in the form of5/8-in. diam rod and, after suitable surface preparation, 5-in. lengths were vacuum annealed at 820°C. Half of the rods for each material were then hydrogenated at 820°C to a nominal hydrogen content of 400 ppm. The hydrogenated and vacuum-annealed A-55 rods were hot swaged at 700°C from 5/8-in. diam to 1/4-in. diam, and then annealed 1 hr at 800°C and air cooled prior to preparation into test specimens. Fabrication of the Ti-8 pet Mn alloy was by hot swaging to 3/8-in. diam at 760" and then 1/4-in. diam at 704°C. This material was then annealed 1 hr at 704", followed by furnace cooling to 593"C, and finally air cooling to room temperature. Evaluation—In order to examine more completely the effects of hydrogen on the particular materials studied, slow-speed tensile and notch-bend impact properties were determined in addition to fatigue data. Tensile specimens were of the standard ASTM type with a reduced section of 1/8-in. diam and a gage length of 1/2 in. A subsize cylindrical Izod specimen was used for impact tests. These specimens had a 45" notch with a 0.005-in. radius and a 0.150-in. root diam, and the stress concentration factor of this notch in bending was Kr = 3. Both the ten-

Jan 1, 1959

By W. B. Triplett, H. I. Aaronson, G. M. Andes

THE morphology and mechanism of the proeutectoid a and the eutectoid reactions have been recently investigated in some detail in an iodide-base Ti—7.22 pct Cr alloy.' These studies have now been extended to an iodide-base Ti—10.8 pct Cr alloy in order to evaluate the effects of composition on the proeutectoid and eutectoid transformations in titanium-chromium alloys. The alloy used in this investigation had the following composition: 10.8 Cr, 0.0327 0, 0.011 N, 0.0063 H, and 0.011 pct C. Specimens of this alloy were heat treated in evacuated and internally get-tered Vycor capsules. The specimens were solu-

Jan 1, 1959

By A. Keil

TO measure the absolute conductivity of metallic specimens it is generally necessary to have exact geometrical shapes and good electrical contact with the test-piece. To overcome limitations of the standard methods, an electronic conductivity-meter* Trade name, Sigmatest; model Dr. F. Forster; Reutlingen, Ger-many. has been developed, which works on the principle of inducing high frequency eddy-currents in the specimens and measuring the reaction of these curients on a measuring coil.',' To attach the instrument to the test specimen, a flat area of about 10 mm diam is all that is necessary. The reading is taken off a scale calibrated in pet of International Annealed Copper Standard. The induced eddy-currents are propagated in a circular motion parallel to the surface. Thickness of the layer included in a measurement depends on the frequency used. With a frequency of 60 kc per sec, the penetration of the currents was 0.8 mm at the upper limit of the scale, and 2 mm at the lower limit. The method is limited to nonferrous metals and other applications have been described elsewhere." The object of the present investigation was to detect the formation and growth of surface layers of differing conductivity, and to determine the depth to which these changes could be observed. A well known phenomenon which illustrates the problem is the internal oxidation of certain silver alloys containing base metal solutes, such as copper or cadmium, when they are annealed in an oxidizing atmosphere.4, 5 Until now, the only methods available for following these phenomenon have been metallo-graphic examination and hardness tests.0, 7 Changes in mechanical properties of copper alloys by internal oxidation were recently discussed in a more general way by Martin and Smith." When measuring these conductivity changes it must be remembered that the only absolute values of conductivity are those of 1) the nontreated homogeneous specimen, and 2) the final values obtained with a surface layer of depth comparable to the penetration of the eddy-currents. All intermediate values refer to the mixed conductivities of the transformed surface layer and the untransformed alloy, and are thus readings of relative value only. Experimental Results Specimens were annealed for 1/2 hr at 800°C in hydrogen, and the internal oxidation was carried out by thermal treatment in air at 800°C. Fig. 1 shows the results of the first series of experiments. With internal oxidation of a solid solution of 8 pet Cd in silver, the conductivity rises continuously until the surface layer formed has become thick enough to be the deciding factor (about 400µ). Precipitates of CdO are mainly in the form of points, Fig. 2, and, as a result, the electric contact between the silver crystals is not distorted by them. Brine11 tests were run with a 1.25 mm ball and a 7.812 kg load. The specimen annealed in hydrogen and oxidized to a depth of 400µ had a hardness of 40 Bhn,

Jan 1, 1959

By D. D. Pollock, D. I. Finch

PREVIOUS work' on a four-component system (Cu-Mn-Ni-Fe) resulted in the development of consistent relationships between the chemical composition and the electrical properties of these manganin-type alloys. The present study was undertaken to develop alloys with temperature coefficients of resistivity and thermoelectric properties more desirable than those of the manganin type, and to determine whether the relationships which had been found for the Cu-Mn-Ni-Fe alloys could be extended to five-and six-component alloy systems. PREPARATION OF ALLOYS The five- and six-component alloys were made from OFHC copper rod, ARMCO iron, electrolytic nickel, manganese cathode chip, and special high-purity aluminum and indium. A Cu-Mg master was used for deoxidation. The compositions of these materials are given in Table I. The alloys were melted and cast as indicated previously,' except that no cover was used and the melts were teemed. EXPERIMENTAL PROCEDURE The finished wire size of 0.0808 in. diam was again selected for the reason that the test specimens would be self-supporting, thus eliminating any extraneous effects which might have been introduced by winding smaller diameter wire on spools or forms. The following tests were performed on the finished wires: A) Chemical Analyses—All of the components of these alloys were determined by premium gravimetric methods. The principle residual impurity contained in these alloys is 0.008 pct Mg (by weight), maximum. Tables II and 111 present the mean analyses computed from at least four determinations of each constituent. B) Electrical Characteristics—The test procedures forthe determination of the thermal emf vs copper, resistivity, and the resistance-temperature relationship are given in detail in Ref. 1. It was also shown that the resistance-temperature relationship is of the form Pt = P,n + At -B/2, [1] where P, is the resistance at t C expressed in percent of a given standard resistance, P, is this per- 0 centage at 0°C, and A and B are constants for a given, properly treated, composition. The results of the electrical tests are also given in Tables II and 111. INTERPRETATION OF DATA The modified Linde2 formula, known to be valid for dilute binary solid solutions, was applied to the complex Cu-Mn-Ni-Fe type alloys. This relationship is of the form where Ap is the increase in resistivity. Zb the valence of the solute, Zn the valence of the solvent, and K and K are designations assigned by Robinson and Dorn3 to the constants for the periodic group to which solute element belongs. The units of K, are -cm per valence difference squared per at. pct; those of K2 are pa-cm per at. pct. For the sake of brevity, these units are not repeated in the following discussion. Calculations were made to determine if this formula was accurate for five-component systems. No experimental studies were made of the Cu-In and Cu-A1 binary systems. The effects of indium additions upon the resistivity of copper are given by Linde. These data, along with those of the effects of Mn and Fe, permitted the calculation of the effects of Al.

Jan 1, 1959

By A. P. Young, F. C. Holden

IN many of the early investigations of the aging of titanium alloys, it was observed that the retained beta phase could be aged to a high hardness without an apparent change in microstructure; moreover, in some alloys it was found that even a very rapid quench produced beta having an anomalously high hardness. What appeared to be hard beta phase was designated as "beta prime," to distinguish it from the softer normal retained beta phase. Frost and co-workers'.' demonstrated that the increased hardness is caused by the formation of a metastable phase, omega, which can be identified from its X-ray diffraction pattern. This reaction also has been studied by Brotzen, et a1.,3 and the structure of the omega phase has been published by Silcock, et al.," and by Austin and Doig.3 The X-ray diffraction analysis by Austin and Doig indicated that omega is low in alloy content, approaching the composition of the stable alpha. The aging process proceeds by the path Thus, overaging results in the formation of alpha and the ultimate disappearance of omega. This is accompanied by a decrease in hardness and a recovery of ductility. The present work represents a study of the aging process in a high-purity Ti-6.4 Mn alloy, in which optical and electron microscopy, X-ray diffraction, and hardness data were correlated. The specimens, 1/8-in. sections cut from 1/4-in.-diam rod, were heated in argon to a temperature just into the beta field (810°C), held for 1 hr, and water-quenched. The aging samples were heated in air for 1 hr at 300 to 500°C. The specimens were ground and mechanically polished, finishing with alternate etching and polishing on a slow-speed wheel to remove disturbed metal from the surface. The surface finally was swab-etched, rinsed with tap water, and air-dried. The etchant used was an aqueous solution containing 1 1/2 pct HF and 3 1/2 pct HNO3. This procedure is identical with that used for preparing metallographic specimens, except that the optimum degree of final etching required for electron microscopy may vary from that used for light microscopy. Metal replicas, backed with silica, were prepared from plastic strip-pings for examination with the electron microscope. Complete details of the procedures used for preparing these replicas are available elsewhere." Fig. 1 shows a comparison between the structures revealed by the electron microscope and those obtained by conventional light microscopy. Hardness and X-ray diffraction data are listed in Table I. No evidence of a second phase is apparent in the optical micrographs for the as-quenched sample, or for the specimens aged at 300 or 400°C; fine alpha particles can be seen in the specimen aged at 500°C. In the electron micrographs, visible equiaxed pocks appear in the as-quenched specimen, and, with increasing density, in the samples aged at 300 and 400°C. After aging at 500°C, the structure becomes markedly coarser and develops an oriented appearance of a second phase, coincident with the appearance of visible alpha particles in the light micrographs. These observations are confirmed by X-ray diffraction and hardness data. In these specimens, aged for 1 hr, the intensity of the omega pattern increases to a maximum at the 400°C aging temperature, corresponding to maximum hardness and the maximum density of pocks in the electron micrographs. At this point the beta phase shows a definite enrichment in Mn. At 500°C, little or no omega re-

Jan 1, 1959

By D. C. Buffum, L. D. Jaffee

THAT the path of brittle fracture in temper brit-tle steel differs from the path in unembrittled steel has been known for some years1 More recently it has been recognized that alloy steels, at least, display two forms of temper brittleness1 which may be called upper-nose and lower-nose. No experimental evidence has been published, however, to show that the two forms can be distinguished by simple inspection of brittle fractures. Fig. 1 is a photograph of the fractured surface of a V-notch Charpy specimen of SAE 3140 steel in which temper brittleness developed during heat treatment in the lower-nose temperature range.' The steel was austenitized 1 hr at 900°, tempered 1 hr at 675", and embrittled 48 hr at 500°C, with water-quenching after each treatment. The temperature of transition from ductile to brittle fracture in the Charpy test was + 2°C (criterion of transition: 100 pet fibrous). The hardness was Re 25; the austenite grain size ASTM 8. This specimen was broken at 150°C in the standard Charpy test and absorbed 6.6 ft-lb; its fracture was rated 0 pet fibrous. Fig. 1 shows that the fracture appeared rough to the naked eye. At the side of the specimen away from the notch (the side which was in compression during the test), the surface as a whole deviated sharply from a plane. At higher magnification, X60, the surface gave

Jan 1, 1959

By E. I. Alessandrini, A. U. Seybolt

Selective oxidation (preferential oxidation of a single alloy component) can be an important oxidation mode in the case of alloys such as Si-Fe, Al-Fe, and so on, when heat-treating in atmospheres of low oxygen potential. It was the purpose of this work to identify the oxide films formed on iron containing 31/4 pct Si at low oxygen potentials, and to make some observations on the H2O/H2 ratios required to form them. EXPERIMENTAL METHOD HYDROGEN of varying water content offers a very convenient method of establishing a wide range of oxidizing power, or oxygen potential. The method chosen to provide a desired H2O/H2 ratio was to nearly saturate hydrogen at room temperature by bubbling the gas through water at room temperature, and then to wring out the excess water by passing the wet gas through a long glass spiral immersed in a refrigerated liquid at a desired dew point. After oxidation, the samples were examined by electron diffraction in order to identify any film which might be present. PREPARATION AND TREATMENT OF SAMPLES The samples were prepared from a Si-Fe alloy made in the laboratory using electrolytic iron and 96 pct ferro-silico11, vacuum-induction melted, hot-rolled then cold-rolled to 0.015-in. thickness. After the cold-rolling the samples were annealed at 1000°C. Transmission Laue X-ray patterns showed very little evidence of preferred orientation, but it is likely that a weak texture could have escaped notice. The chemical analysis was as follows: 3.34 Si, 0.01 Al, 0.001 0, 0.006 C, 0.002 N. Before each sample was oxidized, it was polished through 4/0 emery paper, cleaned and dried using benzene, carbon tetrachloride, acetone, absolute alcohol, and ether. The method of oxidizing the samples was as follows: Samples about 1/2 by 1 by 0.015 in. were held in the upper, cool part of a vertical vacuum furnace until the desired temperature was established in the furnace, Fig. 1. The sample was then lowered into the uniform hot zone where it was heated quickly to the desired temperature, and subjected to hydrogen of controlled moisture content (dew point) as mentioned previously. Temperatures from 400" to 1000°C were used, and dew points from room temperature to —78°C were explored. In general, the runs lasted about 6 hr, but a few runs were of different duration, as will be indicated later. After the predetermined period of time had elapsed, the specimens were withdrawn by the hollow stainless steel-quartz holder to a cool zone at the top of the furnace. EXPERIMENTAL RESULTS The results are summarized in Table I. Most of the electron-diffraction patterns were obtained by glancing-angle reflection, but in a few cases it was possible to strip the oxide films from the surface by a total immersion in a 3 pct bromine-methanol solution. Some of the thinner stripped films yielded quite satisfactory transmission patterns. However, both diffraction techniques yielded the same results; the patterns while most frequently showing a (low) tridymite, also showed a (low) cristobalite in some cases. A few patterns showed evidence of both phases. Because of the known nonequilibrium behavior of silica, it is not surprising that both forms of silica could coexist on one sample. It was noted that at fairly low dew points such as —40°C, there was a tendency for diffuse diffraction rings, suggesting a very small crystallite size. Also some subsequent experiments to be reported later show that thin silica films can be amorphous.

Jan 1, 1959

By M. J. Sinnott, J. C. Tobin

A technique for collecting and analyzing the small quantities of gases desorbed on heating metal powders has been developed. The gases collected from copper powders of various types of manufacture have been analyzed and found to contain H2O, CO2, and SO2. The quantities of gas evolved vary from 0.05 to 1.0 milliliter, under standard con-ditons of temperature and pressure, per gram of powder. The source of the gas has been traced to surface films on the powder. IN the powder-metal industry it is recognized that the presence of gases in the powders affects the processing and resulting properties of the sintered product. Several sources for these gases are possible; namely, chemical reactions with the sintering atmospheres, inclusion. of gases during compacting, dissolved gases in the metal powder, and sorbed gases on the metal-,powder surfaces.1, 2, 3 Since the quantities of the gases are relatively small, no direct attempt has been made to collect and analyze them nor to isolate their source. The work that has been done has been concerned with the dimensional stability of the product., its porosity, density, or mechanical and physical properties. Conclusions are drawn on the basis of studies of this type as to the probable effect of gases on these properties. 4, 5, 0 In the present investigation an attempt has been made to obtain quantitative data on the analysis and quantities of gases associated with copper powders manufactured in different ways. Apparatus was constructed to collect gases evolved from loosely packed powder samples on heating to various temperatures under a reduced pressure of helium. The powders were outgassed thoroughly in a vacuum prior to starting the collection operation in order to eliminate mechanically entrapped gases and to prevent the possible reaction of the powder with these gases. Experimental Procedures Materials—The major portion of the investigation was carried out on a single heat of water-atomized, oxygen-free, high-conductivity copper. A relatively coarse fraction of this powder, 20 to 100 mesh, was tested as a mixed powder and as various graded size fractions. The microstructure of this powder showed equiaxed grains and was clean and free from oxides and oxide eutectic. The particle size, as determined

Jan 1, 1959

By J. E. Hove

The high temperature physical properties of graphite are reviewed and interpreted in the light of present day knowledge of the mechanisms affecting these properties. The thermal and mechanical behaviors only are discussed and, whenever possible, comparisons are made with other refractory materials. Possible further studies are indicated, including some carbide work. AS long as the term high temperature implied only temperatures up to about 1000°C, the materials problems which arose could usually be handled by fairly conventional metal alloy types, such as the Co-Cr-Ni superalloys, for which there exists a great deal of technology. Perhaps this temperature can still be considered an upper limit for normal applications, but it is certainly true that the number of abnormal applications is increasing rapidly. The advent, in recent years, of ram-jet and rocket missiles and of high power nuclear reactor heat sources has raised a host of questions concerning the basic problem of what material to use in the temperature range up to 2000°C and higher. While there are, of course, many metals, in the second and third transition series, which melt at considerably higher temperatures than this, these metals are, at present, pretty well excluded from practical use by other considerations, such as re-crystallization, chemical activity, or excessive plastic deformation. The behavior of metals, from the standpoint of dislocation theory, is just beginning to be understood and thus there is some hope for the future development of very high temperature metals, but the immediate problems would most logically appear to have solutions involving the nonmetals, such as the refractory ceramics and graphite. For this reason, there is presently a great deal of engineering and experimental research being performed on the latter materials, much of this research being exploratory in the sense of gathering new property data. The situation, so far as graphite is concerned, is somewhat more fortunate than with the other refractory solids in the sense that a great deal is already known about its basic properties. This stems both from the fact that the carbon-carbon bond has been of interest to chemists for a long time (and graphite can be considered as a very large aromatic molecule, if desired) and the fact that its properties, both as a function of temperature and of radiation damage, are of critical importance to nuclear reactor designers. It is still true, of course, that such fundamental questions as why graphite remains solid to such a high temperature and why it has such a high thermal conductivity cannot entirely be answered at the present time. It is, nonetheless, meaningful and instructive to consider such problems in the light of existing knowledge. This is what the present paper will attempt to do. Before going on, it may be appropriate to classify graphite and justify its discussion before readers primarily interested in metals. Graphite is comparatively unique among materials in that there is always a property or group of properties which precludes calling it either a metal, a semiconductor, or a ceramic. It has the high electrical and thermal conductivities of a metal, but the artificial, poly-crystalline types show a negative thermal coefficient of electrical resistivity, generally characteristic of semiconductors. On the other hand, semiconductors, by definition, show an ever increasing resistivity as the temperature is lowered, whereas graphite approaches a finite, and, indeed, a rather low resistivity in the region of 10°K and, furthermore, a good single crystal of graphite has a positive temperature coefficient, as for a metal.' On still another hand, its porosity and brittleness at lower temperatures would put graphite in the ceramic class although, unlike most ceramics, it is readily machinable and has a high resistance to thermal shock. All things considered, it is probably more nearly appropriate to call graphite a metal than anything else. Although certainly outstanding in some ways, graphite has its peculiarities and, especially if the reader is unfamiliar with the data, it is probably valuable to review some representative property variations at high temperature. This review is meant to be mainly illustrative and no attempt has been made to be exhaustive. Review of High Temperature Properties At ordinary pressures, graphite does not melt, but sublimes directly into the gaseous phase at about 3700°C. Although the phase equilibrium diagram is still in some doubt, graphite will melt, at a slightly higher temperature, at pressures in excess of about 100 atm. The chief difficulty of using graphite in an oxidizing atmosphere is that the reaction rate becomes quite high at fairly low temperatures. If a threshold oxidation temperature2 is defined as the temperature at which graphite loses 1 pet of its weight in 24 hr, the value in air is 450°, the value in steam is 700°, and the value in carbon dioxide is 900°C. Efforts are presently being made to raise this threshold temperature either by impregnation with a retardant of some type (sodium tung-state and phosphoric acid, for example) or by a suitable metal or oxide coating. It is probably fair to say that, to date, these attempts have not shown any outstanding success in all respects. Most commercial graphites are fabricated by impregnating a carbon flour (say of coke or lampblack particles) with some type of hydrocarbon

Jan 1, 1959

By J. W. Evans

ONE possible method for the separation of hafnium from zirconium is by the vapor phase oxidation of the purified mixed chlorides. An important factor for success depends on the difference in free energies of the following reactions: ZrCl(g) + O2 = ZrO2(s) + 2C12 [1] HfCl4(g) + O2 = HfO2(s) + 2C12. [2] Prakash and Sundaram1 have calculated these values from certain data and carried out experimental work with partial success. However, their free energy values for reaction 2 diverge rather widely from other data which are presented here. The possibility of successful separation is briefly considered in the light of these alternative values. Table I shows the free energy values (?F°) for reactions 1 and 2 derived from the recent compilation of data on oxides and chlorides by Glassner.2 The corresponding values of Prakash and Sundaram for the same temperatures are also shown. The alternative values to those of Prakash and Sundaram for reaction 2 are substantially confirmed by the data of Kubaschewski and Evans" and Cough-lin' on heats of formation, entropies, and heats of vaporization. In spite of the considerable uncertainty in the hafnium data it is reasonable to suppose that the oxide-chloride free energy difference for two such chemically similar elements would not be very far apart. These figures indicate clearly that the oxidation of hafnium chloride is appreciable at all temperatures. Nevertheless, there is a significant difference between the values for reactions 1 and 2

Jan 1, 1959

By P. D. Zemany, G. W. Sear, B. W. Roberts

Vanadium metal is embrittled by hydrogen at a temperature as low as 250°C when held in the presence of manganese metal and water vapor in a rough vacuum. It is established that the property changes are caused by the catalytic decomposition of water vapor at the vanadium surface and the diffusion into and solution in the vanadium of the resultant hydrogen. It is found that manganese is a necessary component of the catalyst. The manganese is transported in the vapor phase by an unknown molecule. A deuterium tracer experiment demonstates the role of water vapor in the embrittle-ment process. VANADIUM metal foils were observed to become embrittled' at a temperature of about 300 °C when held in the presence of manganese metal and a small amount of moist air, This paper describes the investigation to find the embrittling agent and an understanding of the relatively low temperature reactions that are involved. Experimental The vanadium metal foil used was prepared by cold-rolling and pack-rolling 32 mil sheet" in a series of steps down to 1 mil foil. The original observation was confirmed by sealing vanadium foils of 3 x 10 sq cm into individual Pyrex tubes with manganese powder† and a con- trol tube containing only the vanadium foil. These tubes were evacuated to 10 -5 mm Hg without baking and sealed. After heat treatment for 200 hr at 300°C, the control foil showed no change in duetility, whereas the foil contained in the manganese— containing tube was embrittled. The visual appearance of each was unchanged. A series of Pyrex sample tubes, about 2.5 cm diam and 25 cm long, were prepared, each containing a 3 x 10 sq cm piece of foil and 5 g manganese powder at the lower end of the tube. By reducing the time of anneal and the temperature of these samples, it was found that embrittlement could be created at 250°C in a time as short as 1 hr. Since the vanadium metal used here has been drastically cold-worked by rolling, it is assumed that it contains a maximum number of dislocations. To check the possible necessity of dislocations in this low temperature reaction, a vanadium foil sample was annealed in Vycor for 2 hr at 800°C to re crystallize and reduce the dislocation concentration. Metallographic examination showed grains which were not visible before annealing. The embrittlement procedure was carried out at 300°C and 3 hr. Upon checking the foil no embrittlement was observed. Further experiments demonstrated that about 6 hr at 300°C are required to create embrittlement in the foil. This delay in the onset of embrittlement in the vanadium foil suggests but does not prove that dislocation channels play a role in the embrittlement phenomena. If manganese metal is necessary for this low temperature embrittlement, do other elements in the transition metals group yield the same result? To check this qualitatively, a group of elements of similar atomic radii were obtained and sealed as before into Pyrex tubes with a sheet of vanadium foil. These tubes were annealed at 250°C for 6 hr and included (with radii)-2 A1 (1.4A), As (1.25A), Be (1.2A), Co (1.25A), Cr (1.45A), Cu (1.25A), Fe (1.25A), Ga (1.2A), Ge (1.25L%), Mn (1.3A), Ni (1.25A), Si (1.2A), Ti (1.45A), Zn (1.3A), air, H,O, 10 cm Hg of dry hydrogen, and MnO, powder. Upon testing the above sample foils for brittleness, only the manganese-containing tube yielded a brittle foil. Manganese Transport—To eliminate contact of manganese metal powder and vanadium foil, sample tubes were prepared with fritted glass barriers. The embrittlement reaction was still found to occur. Thus, the mode of transfer of manganese is certainly vapor transport. A vanadium foil was embrittled by this mechanism in an evacuated Pyrex tube for 8 hr at 300°C. By means of X-ray fluorescence analysis,' the amount of manganese added to the surface was established at 5 ±2 x 10 -6 g per sq cm. Since the average rate of manganese deposition is known, an effective average pressure of an assumed carrier compound can be computed. ___ P = M/T v2p mkT

Jan 1, 1959

By W. M. Albrecht, M. W. Mallett

The solubilities of hydrogen in titanium and several of its alloys were determined at 600 to 1000°C and pressures of 0.05 to 10µ of mercury. Solubility increases with increasing beta phase in the alloys. Factors found to affect degassing rates are specimen size and presence of thick surficial oxide. Removal of hydrogen by heating in vacuum and in flowing inert atmospheres was studied. Practical curves predicting minimum degassing times are presented. THE presence of hydrogen in titanium and titanium alloys has detrimental effects on the mechanical properties of the metal.'"," The hydrogen content of commercial titanium is sometimes of the order of 200 ppm by weight' and varies with alloy composition. As a consequence, titanium and some titanium alloys as normally processed are sometimes not ductile unless treated to lower the hydrogen content. The best known hydrogen-removal treatment is heating the material in a vacuum. The rate of removal (degassing) at a give temperature determines the duration of the treatment required to attain a satisfactory low hydrogen level.

Jan 1, 1959

By B. J. Reid, J. N. Greenwood

It has been shown1 that cavities are formed in the grain-boundaries of copper and 70:30 brass (as well as in magnesium) by the application of tensile stresses at elevated temperatures. For a given rate of strain, cavities are formed in brass at a lower temperature than in copper, and they are larger; it was thought that this earlier onset of cavitation in the alloy might be caused by the distortion produced in the metal lattice by the alloying element. If the cavitation is caused by the vacancy-migration mechanism, ' the distortion of the lattice would reduce the energy required for vacancy formation, and thus provide vacancies more readily to assist in the cavitation process. It was decided to study a range of alloys to find out whether increasing amounts of an alloying element would cause any progressive increase in, or modification of, the cavitation in copper. Nickel was chosen for this purpose, since it is soluble in copper throughout the whole range of alloys. A further advantage was its low vapor pressure, which enabled the preparation of the alloys in vacuum and the consequent reduction of their hydrogen content. It has been suggested that cavities may be nucleated by the migration of hydrogen atoms to the less regular atomic spacing at the boundary, and their combination to form molecules. The latter being too large to diffuse back into the lattice, form stable cavities into which vacancies could condense. PREPARATION OF ALLOYS All alloys, ranging from pure OFHC copper to 43.7 at. pct of nickel (carbonyl), were prepared in a vacuum furnace employing high-frequency induction heating. When a charge was melted, vigorous gas evolution occurred initially, after which the pressure was reduced to 10-4 mm Hg, using an oil-diffusion pump. After remaining molten for a further 1/2 to 1 hr to aid degassing, the melt was allowed to solidify in the crucible. In this way contamination by gases evolved from the surface of a separate mold was avoided. The list of alloys prepared is shown in Table I. The percentage of hydrogen present in the OFHC copper was reduced from 0.0054 at. pct to 0.0012 at. pct, as measured by a vacuum-fusion method. The alloys were cold-rolled to 0.03-in.-thick strip, and were homogenized in vacuum for 1 hr at 900°C after every 30 pct reduction. At a thickness of 0.05 in., the strip was held at 450°C for 24 hr under high vacuum (10-5 mm Hg) in an attempt to reduce the hydrogen content still further. Tensile specimens were prepared with a gage length of 1 in., and were finally annealed for 2 hr at 800°C to give an average grain diameter of 0.1 mm. TENSILE DEFORMATION The specimens were deformed in a tensile straining machine operated by a synchronous motor at a constant rate, equivalent to 1.7 pct per hr on a 1-in. gage length. The specimen and grips were contained in a vacuum jacket. A pressure of 10-2 mm Hg was maintained, which was sufficient to prevent surface tarnishing of a specimen held at 650°C for 24 hr. Tests were made between 20. and 650°C and the temperature was controlled to within ±3° over the gage length. The load was measured by the deflection of a cantilever spring. a) Mechanical Properties-The ductility curves shown in Fig. 1 fall into two groups. Figs. 1(a) and (b) for copper and the 5 pct nickel alloy, respectively, show a continuous fall in ductility with a steep fall between 200° and 400°C. Figs. l(c) to (f) show the same sudden loss of ductility between 200° and 400°C. With higher temperatures, however, there is a recovery in ductility values to a maxi-

Jan 1, 1959

By E. H. Greener, M. E. Fine

The internal friction (1/Q) of cobalt Fig. 1 (measured by an electrostatic dynamic method1) near 250°C begins to increase rapidly on heating and continues to increase until 560°C, the highest tem- perature measured. In the plot of log of 1/Q against 1/T, above 250°C the data nearly fit two straight lines intersecting at 400°C, approximately the temperature of the hexagonal-cubic transformation. The higher temperature branch corresponds to an effective activation energy of 6500 cal per mole, the lower temperature branch 11,000 cal per mole. Young's modulus Fig. 2 increases approximately

Jan 1, 1959

By L. S. Castleman, L. L. Seigle

THE formation and growth of intermetallic phase layers is of considerable practical importance to metallurgists interested in diffusion bonding and cementation processes and has been the subject of extensive qualitative investigation. In contrast, it is somewhat surprising that so little quantitative data have been amassed. The need for additional fundamental work was pointed out by Mehl in 1936,' and persists to a large extent to the present day. The early studies have been reviewed by Rhines,2 and his conclusions have been summarized by Lustman and Mehl3 substantially as follows: 1) All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two metals; however, in some cases, certain of the phases may be too thin to be observed and identified easily. 2) The isothermal growth of intermetallic phases generally obeys a simple parabolic equation of the form X2 = Kt, where x is the thickness of the alloy layer, K the temperature dependent reaction rate constant, and t the time. 3) The rate of thickening varies with temperature according to the Arrhenius equation k = Ae -Q/RT , where k is the parabolic rate constant, A, a temperature independent constant, Q the heat of activation for the process, R the gas constant, and T the absolute temperature. Subsequently, Lustman and Mehl made a quantitative study of the laws of growth in intermediate layers in a number of binary systems, in which one of the components was either zinc or cadmium, and the other component was one of the following: nickel, copper, silver, cobalt, gold, iron, or Monel metal; the interdiffusion times used were for the most part less than 24 hr. It was found that the simple parabolic law was not obeyed in general, but that a generalized parabolic law of the form xn = kt was valid, where n was a temperature dependent constant; also,

Jan 1, 1959

By M. T. Simnad, R. F. Mehl, L. Yang

Techniques for studying marker movement in K-Rb interdiffusion have been worked out. The results indicate that Rb diffuses faster than K and that the ring mechanism of diffusion cannot be the dominant one operating in this case or probably in cases involving other alkali metals, despite their low ion core repulsive energies. SEVERAL theoretical attempts have been made in the past decade to elucidate the mechanism of diffusion in body-centered-cubic metals. No general agreement, however, has been reached by different authors. Zener,1 and later LeClaire,2 on the basis of a correlation between the entropy of activation for self-diffusion and the temperature dependence of the elastic constants, predicted that a ring mechanism should operate in the diffusion of body-cen-tered-cubic metals. Paneth3 calculated the activation energies of various ring, vacancy, and interstitial mechanisms for the self-diffusion in alkali metals and concluded that the most likely one was based on the linear motion of "crowdions," which is in fact a different form of interstitial diffusion. Fumi,1 however, showed that the experimental values of the activation energies for self-diffusion in the alkali metals could be better accounted for if the diffusion process in these metals was assumed to follow a vacancy mechanism. The same conclusion was reached by Kojima5 for the self-diffusion in lithium. Experimental evidences published during the past few years seem to exclude the ring mechanism as the predominating one in the diffusion of body-centered-cubic metals. For instance, maker movement has been observed in ß-brass, first in this laboratory" and later by Resnick and Baluffi.5 Shewmon and Bechtoldh also found marker movement in the body-centered-cubic system Ti-Mo and showed that the argument which led Zener and LeClair to favor a ring mechanism was not incompatible with a vacancy mechanism. In spite of this, it seemed to the authors that further experimental tests should be made by studying the Kirkendall effect in body-centered-cubic systems that characteristically have small ion core repulsion, such as the alkali-metal systems. Since the ion core repulsion term constitutes the main part of the activation energy needed for the rotation of a ring, such a test should be the most critical of all. The system K-Rb was chosen for experimental study because these metals form a continuous series of solid solutions. Experimental Investigation Owing to the extremely active nature of these two metals, a brass dry box (18 x 11 x 10 in.) was built for making the diffusion couple. It had a big lucite window on top, two side ports through which neo-prene-rubber gloves were inserted, and another side port covered with an optically flat-glass window for microscopic examination of the sample. Inside the box there were a circulating fan driven with a rotating horse-shoe magnet located outside the box, a heater used to generate potassium vapor for getter-ing the box, and a cold trap for keeping the inside of the box cool. Chemically pure grade K and Rb were triple distilled before they were transferred in vacuum into cylindrical steel molds kept in pyrex-glass ampules, Fig. 1. The latter together with the tools needed for making the diffusion couple were put into the dry box. After the box was flushed with purified argon and gettered with potassium vapor, generated from a heated steel crucible inside the box, the glass ampules were broken and the mound on the top of the alkali-metal ingot was cut off with a razor blade to yield a flat surface. To make the diffusion couple, one K ingot and one Rb ingot were pushed out of the molds together with their steel supports by screwing a metal plunger into the bottom of each mold. They were then laid on a brass cradle inside the assembling carriage (shown separately in Fig. 2) with the flat faces opposite to each

Jan 1, 1959