Search Documents

By Rolf A. Knopp

This paper discusses how design differences in FLP diesel equipment in underground coal mines came about. "Design standards" tend to create differences between countries while fostering uniformity among products of competing manufacturers. "Performance requirements," on the other hand, tend to eliminate differences between countries while encouraging competitive development of better products. Examples of regulations from the U.S., Canada. Great Britain. Australia. South Africa, etc., are used to illustrate differences in the design and certification of diesel equipment for underground coal mines.

Jan 1, 1978

By T. W. Wlodek

In this paper the relative merits of shot peening, induction surface hardening, spiral-rolling, and the combination of these surface treatments, are evaluated on the basis of their capacity to increase the fatigue strength of drill steel. The S-N relations for plain car-bon steel (SAE 1080) and Ni-Cr-Mo drill steels in the as-rolled condition were determined previously, using the new Canadian method of testing drill steel introduced at the annual meeting of the Institute in Toronto in 1950 (19). S-N curves have now been determined by this method for these two drill steels in the following conditions: shot-peened and drawn, induction hardened, induction hardened and shot-peened, and spiral-rolled. ( S.R.) . The ratios of the fatigue strengths of these steels after surface treatment, to their fatigue strengths in the as-rolled condition, are compared and the most beneficial treatments are thereby pointed out. The expected range of stresses and their distribution during actual drilling operations are estimated from data available, and the mechanism of failure of drill steel in the as-rolled and surface-treated conditions is analyzed. The magnitude of the surface compression stresses and their effect on ?fatigue strength are discussed.

Jan 1, 1958

By W Shamu

The mechanical properties of rock samples of identical lithologicalcomposition may vary significantly due to existence of materialdiscontinuities. Laboratory tests were carried out to determine the effect of material discontinuities on rock sample mechanical properties. The investigations consisted of detecting discontinuities, observing the failure mechanisms during uniaxial compressive strength tests, and analysing of the factors affecting the strength. A non-destructive testing method has been adopted to assist in thedetection of discontinuities. Laboratory testing proved that fractures leading to failures initiated on the detected discontinuities. The location, orientation, size, density and extent of the discontinuities contribute to different modes of failure and these affect the mechanical parameters of rock samples. Four modes of failure were distinguished for hard and brittlecylindrical rock samples. These modes were referred to as simple shear failure, multiple shear failure, multiple fracturing and vertical splitting. To evaluate the effect of discontinuities on mechanical parameters, the ratio of uniaxial compressive to tensile (Brazilian) strength was calculated and analysed for the different modes of failure. It was found that the value of the ratio depended on the mode of sample failure. The lowest value of the ratio was observed for shear mode of failure and the highest for vertical splitting mode of failure.

Jan 1, 1999

By Qingwen Shi, Yun Zhao, Brijes Mishra

The effect of discontinuities on the fracturing and mechanical behavior of shale has been extensively investigated on a laboratory scale in previous works. It is well agreed that the lamination properties, including discontinuity and lamina properties, affect the behavior of shale. However, it is still unclear how the lamination properties are affecting the stability of the shale roof in an underground coal mine entry. This paper investigated the effect of lamination properties using the discrete element method on a mine-scale entry model as an extension to the previous work conducted on laboratory scale models.

Jan 11, 2022

By S. Hume, J. Shepherd

Meso-2,3-dimercaptosuccinic acid(DMSA) was studied as an additive for thiosulfate leaching of gold. DMSA was added to solutionscomposed of either sodium thiosulfate or calcium thiosulfate and the solutions were tested for their ability to leach pure gold samples as well as a calcined gold ore from Barrick Gold Corp. Results showed prolonged leaching of pure gold samples when DMSA was added at a concentration of 5µM; however, higher concentrations were shown to inhibit leaching. Differential capacitance measurements of the interface indicated that DMSA adsorbed as a defective monolayer on the surface of gold at low concentrations and formed a more compact monolayer with increased concentration. It is proposed that a concentration of 5µM DMSA produces a defectivemonolayer on the surface that still allowsthe transport of oxidants to the underling metal while inhibiting the formation of polysulfide passive layers that arise fromdecomposed thiosulfate.The 5µM DMSA/CaS2O3 system was also studied using calcined ore. Results showed that the initial leaching rates in the presence of DMSA are lower than those obtained in thiosulfate alone. However, after 10h, prolonged leaching is again observed when DMSA is included.

Jan 1, 2015

By T. V. Johnson

The microstructural relationships in dolomitic fluxed taconite pellets were studied. The influence of basicity (in the range 0.75 to 2.1) and firing temperature (to 1340°C) on the grain structure, macrostructure, and mineralogical phase relationships are described. Extensive slag bonding of hematite grains begins at temperatures between 1220 and 1230°C, and results in fundamental changes in grain structure. Successive temperature increases result in little change in grain structure until 1340°C, when extensive coalescence of the hematite grains begins.' Increasing flux additions have little effect on grain structure but greatly influence pore character. The compressive strength decreases with increasing flux addition, increases with increasing firing temperature, and is related to the macrostructure of the pellet. The compositions of the slag phases are represented on the CaO-Fe2O3-SiO2 phase diagram, and the compositional path of slag development is described.

Jan 1, 1980

By J Seccatore, T Marin, M Cardu, G De Tomi, F Galvão, A Rezende, E Melo

Small-scale mining operations are characterised by a large variety of equipment availability and a high level of operational flexibility. Mine planning is usually scarce or absent in small quarries in Brazil, and mine management generally focuses on daily operations. As a result, analysis of the effects of unit operations, such as blasting, over the whole mining process is often neglected. The goal of the following project was to study the effect of production blasting on loading and hauling times, secondary breaking times and primary crushing times at the Experimental Mine of the Research Center for Responsible Mining of the University of São Paulo, Brazil. The operations analysed included blasts that performed:under the average operational standard, defined in this paper as Case 1according to quarry standards, defined in this paper as Case 2.In order to establish the effects of blasting on the downstream process, three key performance indictors were used:The time taken to load the truck, when there is the need for material selection. Due to the fact that we do not have an operational baseline, the increase in time cannot be established, meaning that we must content ourselves with comparing the mean time in each scenario.The average time used for secondary breaking machinery.The time required for the primary crusher to fully process the load of a single truck. The results obtained indicate correlations between the coarseness of the blasted material and these operational times. Solutions are suggested and evaluated for the improvement of the small-scale mining process.CITATION:Marin, T, Melo, E, Seccatore, J, Cardu, M, Galvão, F, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The effect of drilling and blasting performance on fragmentation in a quarry and time for loading, secondary breakage and crushing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 355–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By Alain Jardy, Thibaut Quatravaux, Denis Ablitzer

"A numerical model of the Vacuum Arc Remelting process has been developed and applied to simulate remelting of various metallic materials, such as specialty steels, titanium and zirconium alloys. In practice, electromagnetic stirring is sometimes used, resulting in a complex 3D molten metal flow. After having validated the numerical model for different remelting conditions, we can use it to study the effect of applying a constant or alternated magnetic field on the thermohydrodynamic behaviour of the melt pool. The intensity of flow turbulence, computed with a classical k-E model, is shown to depend strongly on the nature of electromagnetic stirring.IntroductionThe principle of the Vacuum Arc Remelting (VAR) process, illustrated in figure I, consists in melting a consumable metallic electrode of the required grade under a high vacuum, in order to obtain a sound ingot of good structural quality.During remelting, an electric arc is maintained between the tip of the electrode and the top of the secondary ingot, in order to ensure melting of the electrode. The metal droplets fall through the arc plasma and progressively buid up the ingot, which solidifies in contact with the walls of a water-cooled copper crucible. The secondary ingot formed in this way contains three distinct zones, corresponding to the liquid pool, fully solidified metal and intermediate mushy zone. In order to stabilize the arc, it can be confined with the aid of a magnetic field created by an external induction coil. This field can also be used to stir the liquid metal, the rotation induced being in the orthoradial direction. By reversing periodically the coil current, stirring can be alternated."

Jan 1, 2004

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By I Zh Bunin, V A. Chanturia, V G. Minenko, M V. Ryazantseva, A L. Samusev

A promising source for the extraction of rare metals and REEs in Russia is the eudialyte ores of the Lovozero deposit, which do not contain active uranium components. The eudialyte ore reserves of the Lovozero Massif are considered virtually unlimited and therefore have the potential to become a primary source of a number of rare and rare earth metals. The goal of this study was to comprehensively examine the effect of the parameters of high-power nanosecond electromagnetic pulses (HPEMP) and dielectric barrier discharge (DBD) on the leaching performance of eudialyte concentrate and the selective separation of zirconium and REEs from productive solutions. Using scanning electron microscopy and infrared spectroscopy, the mechanism behind the intensification of acidic dissolution of eudialyte as a result of pretreatment with energy impacts was described. During the HPEMP treatment, weakening and destruction of the eudialyte surface was observed, which at the substructural level is expressed in the deformation and local destruction of Si10O27, Si9MO30 resulting in formation of microcracks. During the DBD treatment, the formation of characteristic defects was observed in the form of imprints of dielectric breakdown microchannels and individual mineral fragments. Pretreatment of eudialyte concentrate using HPEMP made it possible to increase the recovery of zirconium into the pregnant solution of leaching by 3.4–4.3 per cent (from 86.6 per cent to 90.9 per cent) and by 4.1 per cent (from 86.6 per cent to 90.6 per cent) when using DBD. The increase in the total recovery of REEs was 1.2–1.8 per cent (from 87.7 per cent to 89.2 per cent). The effect of pH values, solution temperature, initial concentrations of valuable components on the successive recovery performance of zirconium and REEs from the pregnant solutions nitric from the acid leaching of eudialyte concentrate by chemical precipitation was examined. The possibility of selective separation of the zirconium product and rare earth elements with a zirconium recovery of 99.95 per cent and a REE recovery of 87.5 per cent was established. REE loss with the zirconium product was 8.0 per cent and 4.5 per cent with the spent pregnant solution.

Aug 24, 2022

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

By Nicholas J. Welham

"The effect of extended ball milling has been studied for two industrial processes: (1) the processing of metal sulphide concentrates; and (2) the carbothermic reduction of ilmenite to synthetic rutile. The plant concentrates were a gold ore with 128 g/t Au of which 8% was non-refractory and a zinc concentrate with copper impurities.The gold concentrate showed complete dissolution of the gold bearing minerals after milling giving almost complete gold liberation. The zinc concentrate showed almost all of the sulphides had solubilized leaving the gangue and elemental sulphur. A study of pure pyrite and arsenopyrite shows that selective dissolution should be possible by a simple leaching process directly after milling.The milling of ilmenite and coal together results in a temperature decrease of 150°C in the subsequent carbothermic reduction of ilmenite, in addition to improving both the rate of reaction and the selectivity of reduction to rutile. IntroductionAlmost all mineral processing plants use mills for the size reduction of particles prior to physical and chemical processing. When continuing beyond size reduction the energy transferred causes deformation, breakage and realloying of particles giving a steady-state particle size. The breaking also causes increasing damage to the crystal structure by formation of smaller grains giving an increasing number of grain boundaries and increasing crystalline defects due to deformation. The increasing number of grain boundaries and defects leads to increased reactivity, which can be seen directly by a reaction within the mill, or indirectly, via a decrease in the subsequent annealing temperature required for reaction."

Jan 1, 1997

By James M. Fragomeni

"The mechanical behavior of an Al-Li alloy was studied and related to the extrusion processing parameters, the plastic metal flow during defonnation, the anisotropy, and the microstructure. The extrusion temperatures, strain rates, extrusion ratios, billet temperatures, and extrusion geometries were varied during processing and correlated with the microstructure and properties. The extrusion processing variables were related to the mechariicar behavior, anisotropy, and microstructure through the ZenerHollomon parameter i.e., the temperature compensated strain rate. Based on optical and electron microscopy studies it was found that regardless of the extrusion conditions, the various microstructures for the most part were unrecrystallized for both the as-extruded and the solution heat-treated conditions. Smaller grain sizes were correlated to larger Zener-Hollomon parameters. The extrusion temperature and ratio did not significantly affect the strength or ductility as did the section geometry, which had a large affect on these mechanical properties. The anisotropy of the properties varied substantially when comparing the extruded longitudinal versus transverse grain orientations.IntroductionThe extrusion process also has a substantial influence on: the microsfructure and mechanical properties of a material that is Athens, Ohio, 45701 fonned The plastic defonnation that occurs during the extrusion process alters the grain size, crystallographic texture, anisotropy, subgrain size, dislocation density and various other microstructural features. Often the material being extruded is not homogeneous, therefore variations in the microstructure and properties occur across the cross-section of the final extruded product. The mechanical properties and microstructure can also vary with length since it is hard to maintain a constant temperature throughout the extrusion process. The extrusion temperature often varies from the heat generated during the extrusion process. The demonstration material that was extruded for this .study was an aluminum alloy containing 2.6wt, % lithium and 0.09wt.% zirconium. This alloy was strengthened by heat treatment causing nucleation, growth, and coarsening of coherent metastable o' (Al3Li) precipitates in the microstructure. The ? precipitates which are a consequence 9f artificially aging the AlLi alloy, are spherical, ordered, and coherent with the aluminum matrix and impede the dislocation glide inotion during plastic defonnation. Theo particles grow homogeneously in the matrix, and have the Cu3Au (L 12)"" superlattice crystal structure. Aluminum-lithium alloys are used primarily for aerospace structural applications since they have attractive properties such as a lower density and higher elastic modulus than conventional 2XXX and 7XXX alloys."

Jan 1, 2000

By Takeshi Yoshikawa, Kazuki Morita, Yuichi Kato

"A composite composed of carbon fiber and a Cu-Si alloy is a promising candidate for next generation brake disc materials used in high-speed trains. The composite can be prepared by vacuum infiltration of the Cu-Si alloy into the fibrous carbon matrix. The activity of Si in the alloy plays an important role in controlling the formation of SiC; this formation is attributed to the reaction between the Si in the alloy and the carbon fiber during the infiltration process. Because Fe has strong affinity with Si, the addition of Fe is expected to decrease the activity of Si in the alloy. In the present work, the variation in the activity of Si in the alloy with the addition of Fe has been investigated by equilibrating a Cu-Fe-Si alloy with solid SiO2 and graphite under controlled CO partial pressure. The first-order and second-order interaction parameter of Fe on Si in molten Cu was determined to be -16 and 160, respectively. The negative value of the first-order interaction parameter clarified the addition of Fe to the Cu-Si alloy is effective in decreasing the activity of Si in the alloy.IntroductionIron-based materials have been commonly used for brake discs in high-speed trains. It becomes critical for brake disc materials to withstand high thermal loads with an increase in the maximum speed of high-speed trains. The fabrication of high heat-resistant, light-weight brake disc materials is then crucial for their use in next-generation high-speed trains. Carbon fiber is known to be a light-weight, high-strength material, and is considered to be a promising matrix material for use in brake discs. The Cu-Si alloy exhibits high thermal conductivity. The composite in which the Cu-Si alloy is added to the carbon fiber matrix is expected to be a high performance material for brake discs. The composite can be prepared by the infiltration of the Cu-Si alloy into the carbon fiber matrix at a temperature higher than 1700 K."

Jan 1, 2012

By H. Bradley Johnson

A number of Federal laws affecting safety and health in the mining industry has been enacted and revised over a period of many years. We have tended to classify these laws and their applicability into three categories: 1) coal mines, 2) metal and nonmetallic mines, and 3) mines with Federal supply contracts. With the growing attention which is being given to mine safety by the Federal government, the entire mining industry should keep aware of all developments in the administration of each of these laws.

Jan 1, 1970

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By M. Misra

The processing strategy for the effective separation of bitumen from low grade (< 10 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1979

By J. D. Miller, M. Misra

The processing strategy for the effective separation of bitumen from low grade (<l0 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However, the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1981

By R A. Anand, N N. Viswanathan, M M. Pande

Slags are the most voluminous solid by-products generated in pyrometallurgical operations, and, as such, finding an application for these oxidic materials is pertinent to maintaining resource efficiency. In particular, pyrometallurgical copper production is associated with high slag rates, typically ranging from 2.2 to 3.0 tons of slag per ton produced copper, which necessitates slag valourisation. A possible application for these iron silicate slags is as supplementary cementitious materials (SCMs), which effectively lowers the CO2 emissions per ton of cementitious material. Although utilising iron silicate slags as SCMs has been studied in previous work, the scientific literature has limited data on the effect of composition on the inherent reactivity in cementitious systems. More specifically, no reports on the impact of FeO/SiO2 ratio have been presented in previous publications. Therefore, the present study aimed to isolate this parameter in a synthetic FeO-SiO2-Al2O3-CaO-MgO-Cr2O3 system. Since the amorphous content is a pertinent parameter for SCMs, a high-temperature confocal laser scanning microscope (HT-CLSM) was utilised to assess the crystallisation behaviour at continuous cooling conditions. Furthermore, high-temperature rheological experiments were conducted to measure the viscosities of the slags in relation to the crystallisation behaviour. The experiments showed that depolymerising the slag by increasing the FeO/SiO2 ratio generated a less viscous slag, which showed higher tendencies for crystallisation. Furthermore, experiments assessing the inherent reactivity as an SCM showed that depolymerising the slag by increasing the FeO/SiO2 ratio as the sole independent parameter generated an initially more reactive slag. However, replacing SiO2 with FeO was found to negatively affect the reactivity as measured over seven days within the tested compositional range.

Jun 19, 2024