Search Documents

By Antonio Marinucci, Robin Mao

The new Hangzhou West Railway Station, which is currently in the early stages of construction, will be located in the city of Hangzhou, China. To accomplish the ambitious goals of the project, the construction work and station building was divided into three project areas. The original design utilizes 1,580 drilled shafts with diameters of either 800 mm or 1000 mm (32 or 40 inch) to support the new Station and its various ancillary structures. The drilled shafts will be tipped into the moderately weathered argillaceous siltstone a distance between 5 and 15 m (16.5 and 49 ft), resulting in an effective pile length ranging from 35 to 43 m (115 to 141 ft), respectively. For the first phase, approximately 550 production drilled shafts will be installed. Eight (8) sacrificial drilled shafts each with a diameter of 1000 mm (40 inch) were installed to a depth ranging from 50 to 57 m (164 to 187 ft), and were tested to confirm the design parameters used for the first phase, to evaluate the contractor’s installation means-and-methods, and to provide guidance whether redesign is warranted for the subsequent two phases. Bi-directional static load testing was performed using a donut-shaped Super Cell to apply unidirectional axial loads up to 13,200 kN (2,970 kip). This paper will describe the bi-directional testing and select results obtained therefrom. The axial compressive and uplift resistances determined from the testing verified that the available axial resistance of a single drilled shaft exceeded the minimum design requirements.

By Diane Reid, Antonio Marinucci, Robin Mao

Super Cells are an innovative, open-shaped bi-directional static load testing device used to promote concrete flow during placement while utilizing greater cross-sectional area of the pile to achieve large applied axial loads at relatively low hydraulic pressures (≤ 250 bar). This paper describes the results of multi-level load testing performed on a sacrificial drilled shaft that was 3.8 m (12.7 ft) in diameter and 110.6 m (363 ft) in length for the Jiaxing-Shaoxing River Crossing Bridge that spans Hangzhou Bay in Shaoxing, China. The test shaft was instrumented with embedded strain gauges and telltale rods along with displacement transducers at the top of the pile to measure the load-induced displacements along the length of the shaft. Load testing was performed twice using a Super Cell placed near the tip of the shaft, prior and subsequent to tip post-grouting, and then again using a Super Cell placed higher in the shaft. The axial resistance for the tested conventional drilled shaft was more than 5 times greater than the estimated axial resistance. In addition, the axial resistance after tip post-grouting (347,100 kN (39,033 ton)) was about 5.3% greater than the ungrouted axial resistance (329,600 kN (37,050 ton)). INTRODUCTION During the past few decades, the magnitude of axial, lateral, and flexural loading has considerably increased due to updated design codes, larger superstructures, and the manner in which extreme event loading (e.g. seismic and scour) is incorporated into design. The diameter and depths to which bored piles or drilled shafts are constructed have increased considerably during the last three decades due to the advancements in equipment technology and capabilities. In addition, monoshaft foundations have become increasingly used, as one large drilled shaft is able to replace a group of smaller diameter piles connected by a cap. Correspondingly, adequate strata, for both side and end resistance, must be discovered/determined as well as achievable to be able to construct the required foundations to support the greater design demands. As design demands have increased, the need to ensure integrity, quality, and performance of a constructed drilled shaft has become ever more crucial. Load tests are essential to validate design assumptions of side and end resistances, to assess the behavior and load transfer characteristics of the constructed drilled shafts, and to evaluate construction methods. Load tests utilizing a bi-directional static load testing (BDSLT) device can achieve considerably large applied axial loads and can be performed more economically, in less time, and in a much safer manner than conventional top-down static load testing methods.

Jan 1, 2019

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2009

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

By C D. Rose

A review and summary of the results of 120 coal sampling system bias tests is presented. This review supports new methodology using multivariate statistics currently being considered by ISO TC27 SC4. The current difficulties with ISO 13909-8 are explained and the logic behind the current new working draft is discussed in detail. Bias was detected in nearly 36 per cent of tests reviewed, suggesting that much improvement is needed in designing, maintaining and monitoring the performance of sampling systems in order to avoid sampling bias.CITATION:Rose, C D, 2012. Bias testing of mechanical sampling systems for coal - A review of test results and call for use of multivariate statistical analyses, in Proceedings Sampling 2012 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By T. Panhorst

Evaluation of through-deck blasthole sample reliability at the Lone Tree gold mine revealed a non-systematic bias in the sampling system. Ore is primarily hosted within the Powerline fault zone. Clay gouge, present in the fault zone and typically enriched in gold content, forms agglomerates during blasthole drilling leading to a segregation error during sampling. Replicated samples split from blasthole cuttings piles show through-deck samples to be either significantly enriched or depleted by 1.5 standard deviations or more from the mean gold content of their respective cuttings pile quality of through-deck samples correlates strongly with quantity of clay present.

Jan 1, 1999

By Monte R. Hieb

Study of moisture-induced swelling strain in Pennsylvanian Period rocks of the Appalachian Plateau in West Virginia shows a 2:1 biaxial horizontal anisotropy which trends NW-SE. Oriented in-situ slabs of coal mine roof rock were collected across West Virginia, dry-sawed to size, air-dried to stability, and then monitored for moisture changes and deformations in the horizontal plane through one wetting cycle and drying cycle. Biaxial swelling strains were exhibited in nearly all rocks tested, with maximum horizontal deformations occurring normally-incident to the strike of regional geologic fold structures. This relationship persists as fold strike varies across the study area. A connection with Alleghanian fold development and/or post-Alleghanian fold relaxation is suggested. Deformations were largest in shales, but occurred in sandstones and siltstones as well. During testing, moisture-induced fractures (MIF) developed parallel to the regional fold structure and ranged in size from hairline cracks to sample-destroying cracks that were orthogonal to the observed biaxial swelling strain direction. Preferential wetting and swelling of clay minerals along NE-trending fractures, related to a fold-parallel fracture fabric of regional extent across West Virginia, is the most likely reason for the observed systematic NW-oriented biaxial swelling strains. The testing methods used in this study are simple and inexpensive and produce robust results that offer insight into a regional, anisotropic mechanical weakness that imparts a dynamic, asymmetrical horizontal stress to moisture-sensitive coal mine roof rocks over time. Because a similar mechanical fabric has been reported in Devonian-age shales, these findings may have implications for shale gas developers in the Appalachian Basin challenged by rapid aperture closure rates along horizontallydrilled induced fracture networks in Devonian rocks like the Marcellus Shale. The paper concludes with an example of how the concept of a preferred swelling strain direction might be applied to improve the effectiveness of roof trusses.

Jan 1, 2013

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Ahmed, M.,• "Development of an Integrated Control System for Mine Ventila¬tion and Firedamp Drainage," Mining Engineer, Vol. 127, No. 91, April, 1968, pp. 382-392. Andrews, J. W., "U. S. Mine Ventilation Standards," Paper presented at the International Mine Ventilation Congress, Sept., 1975. Boyle, J. A., and Conn, 0. S., "The Control of Mine Ventilation Utilizing Multiple Main Fans," Paper presented at the Seventy-second Annual CMIA Meeting, Pittsburgh, December 1958. Collinson, P. L., and Vance, W. E., "Mine Ventilation Planning," The Mining Engineer, Volume 121, No. 14, 1961, pp. 141-156. Committee on Industrial Ventilation, Industrial Ventilation, 12th Edition, 1972. Grever, R. E., "Automatic Monitoring of Ventilation Conditions in European Coal Mines," Symposium on Engineering Systems Design for Mine Safety, Michigan Technological University, August 1973. Hall, C. J., Airflow in Mines - Thermodynamic and Motive Column Analyses, The Book Concern, Printers, Inc., Hancock, Mich., 1967, 263 pages. Hargraves, A. J., "Planning and Operation of Gaseous Mines," Canadian Mining and Metallurgical Bulletin, Vol. 66, No. 731, March 1973, pp. 119-128. Harris, E. J., "The Fluid Network Analyzer as an Aid in Solving Mine Ventilation Distribution Problems," SME-AIME Transactions, Vol. 228, 1963, pp. 391-395 Higgins, J., and Shuttleworth, S. E. H., "A Tracer Gas Technique for the Measurement of Airflow in Headings," Colliery Engineering, November 1958, Vol. 35, pp. 483-487. Kaiser, K. M., and Bhowmick, B. C., "Recent Developments in Mine Ventila¬tion Instrumentation," Journal of Mines, Metals & Fuels (INDIA), June 1974, pp. 155-162. Kalasky, J. D., and Krickovic, S., "Ventilation of Pillared Areas by Bleeder Entries, Bleeder Systems, or Equivalent Means," Trans¬actions AIME, Volume 254, December 1973, pp. 284-291. Mahajan, J. K., "Ventilation Planning for a Deep Metal Mine," Min. Geol. Met. Inst. India, Volume 69, 1972, pp. 31-38.

Jan 1, 1977

By H. B. Humphrey

WHEN THE BUREAU OF MINES was created in 1910, the organic act had as one of its main provisions the following: That it shall be the province of said bureau and its director, under the direction of the Secretary of the Interior, to make diligent investigation of the methods of mining, especially in relation to the safely of miners and the appliances best adapted to prevent accidents, the possible improvement of renditions under which mining operations are carried on, the treatment of ores and other mineral substances, the use of explosives and electricity, the prevention of accidents, and other inquiries and technologic investigations pertinent to said industries, and from tinge to time make such public reports of the work, investigations, and information obtained as the Secretary of said department may direct, with the recommendations of such bureau. The nationwide nature of the health and safety work of the Bureau of Mines has given its representatives an opportunity to study and report on matters pertaining to health and safety in mines and related operations from the time the Bureau was established to the present. Regular annual reports and numerous additional papers and reports have been published each year to place on record and to make available the information gathered. While the basic purpose of this bulletin is to describe health and safety reports for the period January 1947 through June 1955, a selected number of earlier publica¬tions that are believed pertinent for reference purposes are included.

Jan 1, 1956

By E. P. Carman

1. DAVENPORT, S. J. Bibliography of Bureau of Mines Publications Dealing With Health and Safety in the Mineral and Allied Industries, 1910--46. Tech. Paper 705, 1948, 154 pp. 30 cents. 2. FJELDNER, A. C., FISHER, P. L., AND POLLOCK, M. B. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1940 to 1945. Tech. Paper 698, 1947, 53 pp. 15 cents. 3. GOOD, J. E., ABREU, ALVARO, AND FRASER, THOMAS. The Coal Industry of Brazil. Part 1. General Economy, Production, and Marketing. Tech. Paper 713, 1949, 38 pp. 20 cents.

Jan 1, 1954

By Samuel S. Wyer

THE following abbreviations have been used in, the text: Cassier's, Cassier's Magazine. Eng. Lond., The Engineer (London). Eng. Mag., Engineering Magazine. Eng. and Min. Jour., Engineering and Mining Journal. Eng. News, Engineering News. Eng. Rec., Engineering Record. Engng., Engineering. Engr., The Engineer (Chicago). J. I. and S. I., Journal of the Iron and Steel Institute. Jour. F. I., Journal of the Franklin Institute. Jour. Assn. Eng. Soc., Journal of the Association of Engineering Societies. Mar. Eng., Marine Engineering. . Mem, Soc. Ing. Civ., France, Memoires de la Society des Ingenieurs Civils, France. Prac. Eng., Practical Engineer. Proc. Digs. Soc. of W. Pa., Proceedings of the Engineers' Society of Western Pennsylvania. Proc. I. C. E., Proceedings of the Institute of Civil Engineers. Proc. I. 1M. E., Proceedings Institution of Mechanical Engineers. Trans. A. I. M. E., Transactions of the American Institute Mining Engineers. Sci. Am., Scientific American. Sci. Am. Sup., Scientific American Supplement. Zcitschr. d. V. D. Ing., Zeitschrift des Vereines Dentscher Ingcnieure.

Mar 1, 1905

By Persifor Frazer

1. SMOKE PREVENTION. Report of Select Committee of House of Commons (1843). Nuisance considerably abated in Leeds (Wm. Backerd, July 13, 1843, 239 pages). A synoptic index, p. 211, gives, in alphabetical order, the digest of every subject taken up. 2. FUEL : ITS COMBUSTION AND ECONOMY. D. Kinnear Clark, C. E. 24mo, 1354 pp. Crosby Lockwood & Co., London (1880). Includes abridgement of treatise on combustion of coal and prevention of smoke, by C. W. Williams, A.I.C.E. 3. DIE RAUCHSCHÄDEN IN DEN WÄLDERN DER UMGEBUNG DER FISCALISCHEN HÜTTENWERKE BEI FREIBERG. Dr. J. v. Schröder, Professor in Tharand, and Dr. A. Schertel, Vorstand des Hüttenlaboratoriums zu Freiberg. Royal 8vo, 27 .pages, 19 pages of tables and a map. Ernst Maukisch, Freiberg (1884). (Aus dem Jahrbuch für das Berg- und Huttenwesen, 1884.) In 1861, Reich and Stockhardt examined the extent of injury to vegetation by the Muldner works. Needles and twigs of pine showed in 100,000 parts : Pb, 5 to 50 ; As, 3.3 to 14.3 ; S02, 62 to 120. In the top twigs, 5 to 8 ; needles, 10 to 16 ; thicker twigs, 10 to 22 ; thinner twig-ends, 17 to 54 of lead. Lead greater in amount in sickly twig-ends with few needles ; also in the bark than in the naked wood of the trunk, which had hardly a trace ; also in the part turned toward the works than on the opposite side. Pb and As diminished in the vegetation with distance from the smelter ; and the same with regard to the soil. Fresh snow was collected, and SO, As, and Pb detected in it.

May 1, 1907

By H. Britton

This bulletin is the seventh in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, 216, and 220 being compilations for the years 1915, 1916, 1917, 1918, 1919-20, and 1921, respectively. In this bulletin the same general plan of classification of references has been followed, but several additions have been made. ACKNOWLEDGMENTS Acknowledgment is made to the following organizations for the use of their libraries in the preparation of this bulletin: University of California, Stanford University, California State Mining Bureau, Union Oil Co. of California, Standard Oil Co. of California, and the Mechanics Mercantile Library of San Francisco; acknowledgment for their assistance is also made to H. H. Hill, C. P. Bowie, A. L. Foster, M. J. Gavin, H. C. Miller, E. B. Swanson, and Miss Louise Janssen, all of the Bureau of Mines, and to Miss Elizabeth H. Burroughs of the Union Oil Co. of California.

Jan 1, 1929

By J. L. Wiley

THIS REVIEW contains abstracts of the technical literature and patents dealing with the history, development, and commercial application of the Bergius and related processes for the hydrogenation, under greater than atmospheric pressures, of liquid and solid carbonaceous materials such as coal, lignite, their distillation and extraction products, pitches and tars, and petroleum and its distillation residues. An attempt has been made to include abstracts of all the published information on this process and of as much of the captured foreign documents and reports compiled therefrom as could consistently be reviewed during the time allotted for the work. Contact with the current literature and patents and review of the foreign documents will be continued and the information will appear in Synthetic Liquid Fuels Abstracts, which is being issued bimonthly as a Bureau of Mines publication. The material in this review is divided in two sections-literature (part I) and patents (part II)-and each of these is arranged alphabetically by author or patentee with further chronological arrangement under each author or group of authors. Secondary authors and patentees as well as assignees are cross-indexed to the main entry. In serial articles or reports the complete series appears in the alphabetical arrangement according to the author of the first member of the series. Succeeding members as well as secondary authors are entered as cross references; Titles of the journals are used as the authors in anonymous references. By following such a procedure, an author index is not required. However, a detailed subject index and a numerical patent list by countries are given as part III.

Jan 1, 1950

By J. L. Wiley

[NOTE. - P before the number indicates that the ab tract appears in patent section. Abstract numbers without. P appear in literature section. A Abietic acid, hydrogenolysis - 404 Acetone, recovery - P-4024 Acetylacetonate catalyst - P-3352, P-3664, P-6067 Acetylene, production - P-2556, P-3169, P-4064, P-4221, P-4222, P-5002 Acid catalyst - P-4584 Salts - P-4555 See also Specific acid. Acid treatment. See Procedure. Adsorption. See Hydrogen, adsorption. Agitation. See Equipment, agitators; Procedure. Alcohols: Decomposition -1128 Hydrogenation - P-3288, P-4743 In motor fuel - 1486]

Jan 1, 1952

By J. Keith Haddock

"IntroductionThe Bienfait Mine is operated by Bienfait Coal Company Ltd., one of the Luscar Limited group of companies. Situated 5 km southeast of the town of Bienfait, Saskatchewan, it can produce 2.0 million tonnes of lignite annually in addition to 158,000 tonnes of char from a carbonization plant located on the property. Geology The economically mineable coal seams of the Estevan area are found in the Ravenscrag Formation. The lignite-bearing sands, silts and clays were deposited in Early Tertiary age, in an inland sea centred in the Williston Basin of North Dakota. The top of the Ravenscrag is an erosional surface, overlain by Tertiary or Quarternary sands and gravels or glacial till. The regional structure is a gently plunging syncline which dips to the southeast at about 0.3 degrees. There are minor undulations in the Bienfait area which are due to differential subsidence during deposition. Sporadic faulting is probably a result of glacial pressures, and preglacial and glacial channels are responsible for washout zones and the abrupt irregular subcrop found in the area. There are two economic coal seams in the Bienfait area, an uppe; seam locally known as the Roche Percee, and a lower seam, the Estevan. Both seams have been extensively mined since lignite mining began in the area in the late 1800s. The Roche Percee remains only in a small portion of the Bienfait Mine and comprises a very minor portion of the reserves. It averages 1.74 m thick under 8.1 m of overburden. The till rests on top of the Roche Percee and due to weathering the seam is generally of poorer quality. The Estevan seam comprises the majority of reserves at Bienfait. The main seam which is being worked on consists of an upper bench averaging 2.75 m, a carbonaceous parting of 0.21 m, and a lower bench of 0.92 m. Overburden depth above this seam varies from 21.0 m to 38.0 m."

Jan 1, 1985

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By H. Dudycz, A. Skoczylas, P. Stefaniak, P. Pyda

In the era of Industry 4.0, technologies such as Big Data (BD) and the Internet of Things (IoT) play a key role, especially for multi-site manufacturing companies. In such companies, the challenge is to collect and process massive amounts of data from industrial devices and extract key information from this data in real-time for ad hoc decision-making. The ability to analyse data from industrial devices translates directly into streamlined production processes, cost optimisation, prevention of unplanned events, and safety during operation. In this context, particular attention should be paid to Big Data Analytics (BDA), whose main source is the Industrial Internet of Things (IIoT). The purpose of this paper is to propose an IT system architecture incorporating BD and the IoT for a mining company. The paper presents results from a literature review focusing on available BD and the IoT solutions for industry (mining in particular) for the purposes of the acquisition, integration, and advanced analysis of data. The advantages and disadvantages of the different solutions were indicated and gaps in the accessibility to dedicated functionality are identified. Based on the analysis of a multi-site mining company, the main challenges faced by such companies planning to implement BD and IoT solutions are identified. Also, a proposal for an IT system architecture incorporating BD and IoT for a mining company is described in the paper. The contribution of the article consists of the identification of the challenges faced by mining companies planning to implement BD and the IoT solutions, and the proposal of an IT system architecture that allows BDA whose main source is the IIoT.

Sep 1, 2021

By Martha Gross, Amanda Wachenfeld, Brian Keaney, Jean-Michel Charpentier, Frank Perrone

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing four-lane bridgetunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. As part of the design-build contract, a supplemental geotechnical investigation was completed to support the design. The investigation for the subaqueous tunnel segment consisted of over 48,400 linear feet of drilling and 7,100 laboratory tests. This paper discusses the challenges of planning and executing a large-scale geotechnical investigation for underground works in a marine environment and the use of big data for effectively managing, interpreting, and transmitting data to the design-builder consistently throughout the investigation.

Jun 23, 2024

By AIME AIME

THE Iron and Steel Division and the Institute of Metals Division are laying plans for a rousing meeting the week beginning Sept. 21 in the land of the bean and the cod-at Boston. The two divisions are collaborating with the American Welding Society, the American Society for Steel Treating, and the Iron and Steel Division of the A. S. M. E., to have technical sessions of widespread interest and social affairs that will compare with the best of previous years. In connection with the meetings an exhibition of production and testing equipment, heat-treating equipment, furnaces, welding equipment, and metal products will be held on Commonwealth Pier all week, where those attending may see the latest developments in the field of their own work.

Jan 1, 1931