Search Documents

By Zhi-biao Yin

Copper smelter flue dusts often cannot be directly recycled to the smelting process and accumulate as hazardous wastes requiring environmentally acceptable disposal. Because of the limited amount of flue dust, a separate copper extraction process must be simple and require-a small plant investment. A flue dust process has been developed, consisting of the following steps: (1) roasting a pelletized mixture of hydrated lime and flue dust to fix arsenic and sulfur as insoluble calcium salts, (2) heap leaching the roasted pellets with a buffered ammonia/ammonium salt solution to extract copper as an ammine complex in a lined cell that is the final repository of the leached pellets, and (3) boiling ammonia from the lixiviant to precipitate copper. Condensed ammonia and the filtered solution are returned to leaching. Heap leaching in the final repository cell lowers the capital investment significantly compared with competing extraction processes. Chemistry with respect to arsenic, sulfur and copper is discussed.

Jan 1, 1992

By W. G. Davenport

Changes in copper extraction from 1960 till today are documented. The top ten changes have been: (a) replacement of reverberatory smelting by high intensity oxygen rich smelting (b) growth of the Outokumpu flash smelting to over 50% of the world's smelting capacity (c) successful development of single furnace coppermaking but only for low slag fall concentrates (d) replacement of the batch Peirce-Smith converter by continuous converting, but only in a few cases (e) increased SO2 capture throughout the industry, mainly-as sulfuric acid (f) development of low initiation temperature `big bight' Cs catalysts for treating the continuous high-SO2 strength gases from continuous smelting/converting (g) complete replacement of reverberatory anode scrap and cathode melting furnaces by the Asarco shaft furnace (h) adoption of stainless steel permanent cathodes and automated stripping technology for electrorefining and electrowinning (i) complete elimination of wire bar casting by continuous bar casting/rod rolling (j) development and adoption of extractants for turning weak impure leach solutions into strong pure electrolytes. It is postulated that the biggest possible change over the next 20 years would be complete replacement of smelting/converting by hydrometallurgical processing. However, this seems unlikely due to copper purity, precious metal recovery, and economic concerns. The increasing value of sulfuric acid to many copper companies gives chalcopyrite smelting/oxide-supergene leaching a nice synergy especially with the energy credits now coming from continuous smelters, and their acid plants.

Jan 1, 1999

By Albert W. Spitz

Profitably recovering copper and precious metals from copper bearing scrap is a demanding and frustrating combination of art, science and economics. With fluctuating markets, varying raw materials and increasingly stringent environmental regulations requiring process revisions, practically everything is changing. The volatile copper market constantly shifts the percentage of copper in the scrap that can be economically processed. Scrap that has value one day may incur a disposal cost the following day. Also with less copper in the scrap, more residuals, slag, fume, etc. are generated which frequently present disposal problems and infrequently generate income. The ever increasing amounts of electronic scrap add value to the copper produced by virtue of the precious metals present. Printed circuit board materials create more slag and organic off gases which must be treated. Finally, the emphasis on reducing emissions of organics and other metals, especially lead, is a continuing challenge. Stack gases, fugitive emissions and ambient air quality all demand constant surveillance.

Jan 1, 1997

By Alan James Parker

Chalcopyrite can be converted to pure copper by the following five steps. An exothermic sulfation roast of chalcopyrite; leaching of cupric sulfate from the calcine with dilute acid; precipitation of Chevreul's salt and or other copper sulfites with ammonium sulfite or precipitation of crude copper by autoclaving ammonium sulfite and cupric sulfate at 150°C; dissolution of Chevreul's salt, or the crude copper, as cuprous sulfate, using acidic cupric sulfate in an acetonitrile-water solution as oxidant; precipitation of pure copper by thermal disproportionation of the cuprous sulfate solution. Acetonitrile and acidic cupric sulfate solution recycle. Advantages over conventional processes include lower cost, lower energy consumption as waste heat, sulfur removal as ammonium sulfate or gypsum, rather than as sulfur dioxide and rapid throughput. The net reaction is: 2 CuFeS2 + 4H20 + 15/2 02 + 8 NH3?2Cu + 4 (NR4)2 SO4 + Fe2O3

Jan 1, 1976

By R. S. Boorman, H. G. Ansell

"Poor separation of lead from a copper concentrate of a major base metal producer was thought to have resulted from copper (0.2-0.4%) in the galena which caused it to float with chalcopyrite. No inclusions of copper mineral were detected which could account for the flotation of galena. The tendency for copper-bearing galena to float with chalcopyrite was confirmed by Hallimond-tube experiments in which the floatability of copper-doped synthetic galena (0.1-0.4% Cu) was approximately four times as high as copper-free galena. The difference in the cell edge (5.9338 ± 0.0003 A, Cudoped galena; 5.9361 ± 0.0002 A, Cu-free galena) indicated that the copper was lattice-bound and did not occur as submicroscopic mineral inclusions."

Jan 1, 1973

By John V. Beall

Copper production in the. United States in 1972 amounted to 1,658,000 tons according to the USBM. This figure is up over 1971 but falls below 1970 production of 1,719,101 tons. This report is essentially about the status of copper mining operations in the U.S. and is an update and expansion of the report "Southwest Copper-A Position Survey" published in [A=], October 1965. At that time, the trend was toward using larger equipment to mine lower grade ore and toward the expansion of dump leaching practice. That trend continues today but, it is overlain by intensive activity to comply with existing environ¬mental legislation and uncertainty over proposed revisions of venerable laws governing mining. In the U.S. today there is, practically speaking, no excess smelting capacity so that expansion of copper production through the startup of new mines is inhibited. Owners of a large undeveloped orebody would have to decide before going into production whether to sell the concentrates offshore, which has many problems, whether to try one of several unproved chemical processes for producing refined metal from concentrates or embarking on the construction of a traditional pyrometallurgical plant in the face of considerable uncertainty over the pollution standards that eventually must be met. The situation is such that not only is the present rate of U.S. copper production threatened but the ability to meet projected increased demand in the years ahead may have been severely retarded.

Jan 4, 1973

By J. G. LECKIE

During the first ten months of 1943 copper was produced at a higher rate than in 1947. However, on Oct. 24 one of the large mines was shut down due to a strike. As of Dec. 31 the strike was still in effect and had already resulted in a loss of production of 50,000 tons of copper. The demand for copper was considerably greater throughout the year than the supply. The price of electrolytic copper delivered at the Atlantic Seaboard refineries advanced from 21.20 to 23.20 cents per lb during the year. This sustained demand for copper, together with the increase in price, has had the natural effect of spurring interest in uncovering new deposits, and in re-examination of known low-grade deposits and old tailing clumps. This is in addition to the usual reevaluation activities which normally result from the constant improvements in efficiency of ore concentration.

Jan 1, 1949

By R. L. Player

"The Copper Isasmelt process has been developed over the past 15 years by Mount Isa Mines Limited (MIM) and the Commonwealth Scientific and Industrial Research Organisation (CSIRO). The first two commercial plants were commissioned in mid 1992.The results of four heat balances on the Mount Isa plant are presented. At a smelting rate of 98 t/hr of chalcopyrite concentrate plus 14 t/hr reverts, the total heat generated was -91MW. Approximately 39% of this energy came from coal, while 50% of the energy reported to the process waste gas. To a first approximation the furnace is near chemical equilibrium.The impurity distribution in the Mount Isa plant was presented. Approximately 91 % As, 85% Cd, 75% Bi, 68% Zn, 60% Sb and Tl, 45% Pb and 30% Te in concentrate was eliminated from the matte.The ""bubble"" frequency of the gas cavity below the foot of the lance was measured at -2. 1Hz. Side bands displaced by -l.lHz modulated the bubble frequency. This was consistent with radial gravity wave motion in the slag bath. The two processes, gas bubbling and wave motion appeared to be coupled together; the bubble frequency was twice the slop wave frequency. IntroductionCopper Isasmelt has been developed over the past 15 years by Mount Isa Mines Limited and the Commonwealth Scientific and Industrial Research Organisation. The process is based on the Sirosmelt lance, invented by researchers at the then Division of Mineral"" and ProcessEngineering ofCSIRO in 1973.The first two commercial scale copper furnaces were commissioned at Mount Isa and the Cyprus Miami Mining Corporation smelter at Miami, Arizona in August and June 1992 respectively.The process concept, the history of the development, and the Mount Isa plant have been described (1, 2, 3).This paper sununarises heat balances obtained on the furnace, the impurity distribution among the output streams and lance injection characteristics."

Jan 1, 1996

By G D. Richmond, J C. Chomley

Copper has been mined intermittently at Gunpowder, north of Mount Isa, since 1927. Most ventures have had some initial success but fluctuating copper prices, the small-scale of the operations and the remoteness of the site led to closures or sale. Processing routes have included direct sale of high grade ore, flotation of oxide and sulphide concentrate, and copper cement production from mine solutions. Copper cathode has been produced by heap and in-place leaching coupled with solvent extraction and electrowinning (SX/EW). Aberfoyle Limited recently purchased the Gunpowder operation and is expanding operations. An innovative high recovery tank leaching process, including a low temperature, low pressure autoclave, has been adopted. Copper cathode will be produced from an expanded solvent extraction/electrowinning plant at approximately 45 000 tonnes per year. The combination of expanded throughput and high metal recoveries will make Gunpowder a cost competitive producer.

Jan 1, 1998

By G. Sedelnikova

This paper is aimed to elucidate the problem of copper losses in pyrometallurgical slag. Currently, flotation is used to recover copper from the slag and return the metal into the pyrometallurgical process, but the percentage of recovery frequently remains unacceptable. The process of copper leaching from the slag flotation tailings using biologically regenerated ferric sulfate is considered here as an approach to the issue. A sample of the slag flotation tailings containing 0.67% Cu and 4.99% Zn was supplied by the Urals Mining and Metallurgical Company (UGMK, Russia). The Cu and Zn speciation analysis of the sample demonstrated that Cu occurred as 58.1% oxide, 15.4% native Cu, and 18.1% secondary sulfides whereas chalcopyrite proportion was as low as 8.4%. Prevailing Zn species were refractory (58.9% Zn ferrite), and zinc oxide and silicate species made just 37.2% of the total metal content. The silicate generated silica gel that strongly hampered filtration. As demonstrated, Cu recovery is a possibility, which is apparently not the case with Zn. In this work, the stirred tank bioreactor acid leaching employing bacterial Fe3+ sulfate solutions was studied, with ferric sulfate being a product of Fe2+ biological oxidation and not the chemical reactant adding of Fe3+ sulfate. Acidithiobacillus, Sulfobacillus, and Leptospirillum bacilli were employed in Fe2+ biooxidation. Temperature, pH, Eh, S:L ratio, leaching time, and Fe3+ concentration in the source leachate as the process controls were considered. As demonstrated, the process employing biologically regenerated ferric sulfate proved to be more efficient than conventional chemical leaching. Under the optimum conditions, the proportion of Cu extracted into leachate during 2 hours was 79.1%, and that of Zn 27.2%. Precipitation of high-grade Cu sulfide served to extract the metals from the leachate, and Cu extraction was 99.7%. All in all, 23.2% Cu, 0.03% Zn, and 0.02% Fe was returned into the pyrometallurgical process. Keywords: slag flotation tailings, copper leaching

Sep 1, 2012

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By H. M. Shepard

THE copper industry operated at high capacity throughout 1947, with no serious tie-ups in operation as was the case in 1946, when almost the entire industry was shut down by a four-month strike. Refined copper production in the United States averaged 94,250 tons for the first eleven months and deliveries to domestic consumers, including foreign copper for domestic consumption, averaged 114,000 tons per month. On April 29 the import duty of 4d per lb was suspended until March 31, 1949. Copper prices fluctuated considerably for a short time thereafter. Over the year the price of domestic electrolytic copper at refineries on the Atlantic seaboard advanced from 19.225¢ on Jan. 2 to 21.200d on Dec. 24.

Jan 1, 1948

By A. E. Isaacson

The U.S. Bureau of Mines is studying the effect of supercritical water, at 400' C and 3,500 psi, and subcritical water, at lower temperatures and pressures, on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water'. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. 'Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By J. H. Puffer

The copper mineralization of the Mesozoic Passaic Formation of New Jersey is typical of copper deposits in eastern North American Mesozoic sediments. Most such deposits are located at the base of the first of several basalt flows that are interbedded with continental, red-bed sediments. The copper mineralization is similar in most respects to that of the Keweenawan Basalts of the Lake Superior area. The first basaltic flow units of the eastern North American Mesozoic basins, and the Keweenawan Basalts, are continental quartz tholeiites of similar chemical composition and copper contents. The copper minerals and associated zeolite facies metamorphic mineral assemblages of these two rock units are also approximately the same. Stoiber and Davidson (1959) suggested that Keweenawan copper was mobilized and concentrated during metamorphism. The evidence pertaining to the Mesozoic copper deposits of New Jersey is consistent with such an interpretation and also with DeVore's (1955) suggestion that ore fluids commonly arise as a result of the mobility of metals under metamorphic conditions. There is additional evidence that final metamorphic concentration of Mesozoic copper was preceded by an initial stage of hydrothermal precipitation related to fluids emitted by basaltic magma.

Jan 1, 1987

By E. D. Gardner

From the standpoint of tonnage and dollar value copper is the most important nonferrous metal mined in North America. The opening of copper mines has had an important bearing on the development and settlement of many sections of the continent. The prosperity of many of the mining States or provinces depends directly upon the copper-mining industry. Normally, about 35,000 men are employed in the copper mines, mills, and smelters of the United States. The United States is the most important producer of copper among the nations; more copper is mined in North America than in any other continent, and for many years the United States alone produced about half of the copper of the world. During the last 10 years increasing production in South America and Africa has reduced the relative importance of North America and the United States.

Jan 1, 1938

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By M. van de Vijfeijken

This paper will first give a short overview of the Copper Mountain project in British Columbia, which just has started commercial operation earlier this year. The grinding process with one 34' x 20' SAG mill and two 24' x 39.5' ball mills will be briefly discussed. All three mills are gear driven by a ring gear, dual pinion and two low speed synchronous motors. Copper Mountain has installed on all three mills, the new state-of-the art dual pinion mill drives. All the inherent operation and maintenance features of this drive technology will be discussed, as well as the advantage of having variable speed control also on the ball mills. The installation and commissioning of the mills and drives at Copper Mountain will be briefly reviewed. Finally the first field measurements on these low speed mill drives will be presented, with the main focus on the low mechanical stress impact of these mill drives on the pinion and ring gear, as well as the accuracy of the load sharing between the two motors.

Jan 1, 2012

Copper nickel separation is performed by mineral processing techniques both pre and post smelting in Copper Cliff at Vale Canada?s Operations. The separation at Clarabelle Mill takes advantage of the ore mineralogy to affect a separation on the rougher concentrate where chalcopyrite and pentlandite exhibit high liberation and high recoveries thus their separation is simple although incomplete. The copper concentrate comprises only 50% of the copper in ore with the remaining copper being separated post smelting in the Matte Separation plant where the slow cooled Bessemer Matte is again treated by mineral processing operations using flotation to separate the chalcocite and heazlewoodite and magnetic separators to remove a metallic nickel alloy. This paper discusses the mineralogy, separation processes and work currently underway to improve the separation of copper from nickel in these plants.

Sep 1, 2012