Search Documents

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has developed a laboratory apparatus for continuous separation of minerals according to their dielectric properties. The unit consists of a rotating wire grid drum electrode and a fixed curved wire screen electrode positioned 3 mm apart. By applying high voltage across the electrodes, which are immersed in a dielectric fluid medium, a high-gradient electric field is produced. The high-dielectric-constant minerals are attracted and conveyed through the separator by the rotating drum electrode, whereas the low-dielectric-constant minerals settle through the fixed electrode. In typical tests, a sample of Montana chromite ore containing 43 percent chromite was concentrated to 72 percent chromite with 90 percent recovery.

Jan 1, 1977

By J. Budac, E. Krause, C. L. Stewart, D. Wrana, S. W. Laundry

"As part of an over-all arsenic management strategy, Inco has developed a novel process that converts a by-product high moisture copper/arsenic sulphide precipitate into a crystalline copper arsenate suitable for the manufacture of wood preservation chemicals.The copper/arsenic sulphide precipitate is atmospherically leached with oxygen and sulphuric acid, producing a crude (blue) copper arsenate precipitate, elemental sulphur, and a copper and nickel containing solution. The blue copper arsenate is dissolved with sulphuric acid, the molar Cu/As ratio is raised to 2, and a crystalline copper arsenate (olivenite) is precipitated by the addition of sodium carbonate. Dissolved copper is recovered using metallic nickel (or matte) and elemental sulphur, to produce a low-moisture (low-arsenic) precipitate suitable for standard nickel-copper processing.The process was successfully piloted at Inco's Manitoba Division between September 1990 and June 1991. The copper arsenate product typically analyzed 43% Cu and 25% As, and the moisture content was about 10%."

Jan 1, 1995

By John C. Leighton, C. O. Brawner, Doug Stewart

"Despite the availability of established, sophisticated methods for planning and designing stable slopes in rock, comparatively little attention is usually paid to the problems of carrying out the excavation. Blasting should be carefully planned to obtain optimum fragmentation as well as steep, stable working and final pit walls. The principal difficulty facing a blast designer is the lack of prior information about the many critical blasting characteristics of the rock mass. The common practise of trial-and-error lasting will eventually lead to a suitable program, but must be repeated time after time in variable geology. This frequently results in many blast-damaged slopes. Recent research indicates that monitoring drill performance will yield a Rock Quality Index which correlates to a Powder Factor value. The drilling can provide a continual supply of data, reflecting changes in the rock mass which enables the selection of an economical powder factor.IntroductionWhen planning to excavate a large-scale rock slope, engineer s will generally spend considerable effort to produce a safe, feasible and economical design. Much time will usually be spent on the field map ping, 'structural geologic studies, surface and subsurface hydrology, determination of strengths and effective friction angles of discontinuities, and finally checking stability with the aid of mathematical and analytical models. If the rock cut is to be along a transportation corridor, the prime justification for this time and effort is to produce a clean, stable slope which will be safe for those travelling or working beneath it. For the walls of an open-pit mine, there is the additional economic incentive to maintain the steepest stable slope angle for the minimum stripping ratio (Stewart and Kennedy)."

Jan 1, 1982

Cannington Mine is an underground, hard rock, metalliferous mine located in North-Western Queensland, Australia. Weld mesh is installed to prevent the failure of rock from between the installed reinforcement elements. Corrosion reduces the capacity and life expectancy of mesh and presents a real hazard to underground personnel and equipment as it reduces the effectiveness of the support system. Corrosion influences the economics of the mining operation through the need to conduct rehabilitation of the ground support which involves re-installing new mesh or shotcreting over the affected mesh to protect it from further corrosion. The requirement for rehabilitation is determined by the geotechnical engineer based on an individual visual assessment with little or no engineering input. It was identified that a more quantitative method was required that considered the safety and economic risks involved. A project was undertaken to develop a simple method to evaluate corroded mesh and to provide selection criteria for rehabilitation. A weld mesh corrosion classification has been developed that relates the average wire diameter of corroded mesh to the remaining capacity of the mesh. Accompanying selection criteria provides recommendations as to when rehabilitation may be required based on the estimated residual mesh capacity, the remaining development life, and the level of personnel exposure.

Nov 25, 2010

By V. Beskrovnaya

Oxidised lead-bearing ores of one of the deposits of Russian Federation represent complex raw materials. Its main components are lead (3.2%~4.7%), silver (100~300 g/t) and zinc (0.7%~0.8%). The sample is characterized as oxidized ore. Silicium (37.4%) and iron (33.2%) are its main com-ponents and present in oxide form. Lead presents as cerussite, anglesite and plumbojarosite have a subject role. Zinc occurs as smithsonite. Certain part of zinc is associated with manganese minerals (psylomelane-pyrolusite). Close association of valuables with manganese-iron mineralization is ob-served. Silver is present in native finely dispersed form. Three options of flowsheets have been developed to recover valuables from the ore. 1. Hydrometallurgical flowsheet of lead and silver recovery on the basis of chloride leaching. 2. Flotation. 3. Flotation -flotation tailings cyanidation. Hydrometallurgical flowsheet of ore processing on the basis of chloride leaching (option I) al-lows to achieve recovery into saleable products of 68.8% Pb and 70.2% Ag. High quality lead concentrate with 71.7% lead and 700 g/t silver was obtained during flotation (option 2). Flotation tailings cyanidation (option 3) provides 24% silver additional recovery (from the ore). Technical and economical evaluation demonstrated that ore flotation (option 2) and flotation with subsequent flotation tailings cyanidation (option 3) are the most cost-efficient. Option II is the most cost-efficient variant of 1 tonne of ore processing (9.05 US dollars).

Jan 1, 2014

Develop a cost-effective diesel aerosol sampler that can be used by industry and regulatory agencies to determine the diesel exhaust aerosol concentration in mine atmospheres. The sampler must be easy to use, wearable by mine personnel, compatible with current personal sampling protocols, and inexpensive. Approach The University of Minnesota (University) and the U.S. Bureau of Mines (USBM) have developed and tested a prototype diesel exhaust aerosol sampler. The sampler, however, was complicated and expensive to fabricate. Consequently, the USBM redesigned the sampler to simplify both manufacturing and use, and the sampler was evaluated to ensure equivalency with the prototype. Background The National Institute for Occupational Safety and Health (NIOSH) has recommended that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration." In addition, the U.S. Mina Safety and Health Administration (MSHA) has been directed by an advisory committee to establish a diesel exhaust aerosol standard and regulations to minimize exposure to diesel pollutants in underground coal mines.

Jan 1, 1992

By A Mortazavi, M Akhmedya

Mining is recognised as being one of the most dangerous industries in the world due to the difficult working conditions. Working in such hazardous circumstances in an underground mine often results in a variety of accidents. The working conditions at Kazakhstan’s underground mines have deteriorated owing to a lack of a risk-reduction plan and methodology. This paper evaluates different underground mines in Kazakhstan and demonstrates the employed mining method and the observed failure modes. Risk assessment has long been recognised as a valuable technique for preventing accidents. In the underground mining sector, risk assessment tools play an important role in avoiding work-related accidents. However, geotechnical uncertainty is a significant source of severe incidents like stress-induced roof collapse, wedge failure, seismicity etc, which result in human and financial losses. A geotechnical risk assessment performed early in the mine design process might assist justify a different mine design component, such as different support systems for a dangerous location within the mine openings during mining. The goal of this research is to create a damage/failure database aiming at the development of a geomechanical risk assessment methodology. This work identifies a thematic structure linked to risk assessment and management for the examined Kazakhstan mining sector. As part of the developed database, the dominant modes of failure within the Kazakhstan underground mining conditions were investigated. The study will provide opportunities to establish future research objectives for Kazakhstan’s mining industry where there are significant gaps between state-of-the-art research and mining operations in practice.

Nov 29, 2022

By Ruari Soutar-Dawson, Fisher Wang, Alan Boylston, Michael Denzel

Vertical stirred mills are increasingly used for fine grinding applications in the mineral processing industry due to their high energy efficiency. Thus, modeling power draw is of great interest proven by the effort in previous work including analytical models. In this contribution the development of a DEM-CFD coupled model is presented to determine power draw under different operating conditions. These include grinding media filling level, shaft speed and fluidization as well as changes in grinding compartment configuration. An extensive test program on an especially equipped test mill is initiated to validate the model.

Feb 22, 2026

By L. Patts, J. Rohrbaugh

The Mine Safety and Health Administration (MSHA) has received several reports of filters igniting when high-temperature disposable filters were used on non-cooled diesel exhaust systems in underground coal mines. Based on laboratory testing (to determine the ignition temperature of these filters, which were loaded in the field with diesel particulate matter, or DPM), MSHA determined a maximum safe operating temperature for high-temperature disposable filters. When the results of the laboratory filter ignition testing were reported to the Coal Diesel Partnership (comprised of members of the Coal Industry, Labor, NIOSH and MSHA) the Partnership charged NIOSH with investigating the safe use of high-temperature disposable filters. This paper reports on the design, fabrication and testing of a unique exhaust gas cooling device and the ability of this device to successfully lower filter inlet temperatures and thus reduce the potential for fires.

Jan 1, 2009

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By T. Rockley, B. Goertz, S. McDaniel, J. Brune, K. Bakhsh

"Researchers at the Colorado School of Mines, under a project funded by the Alpha Foundation, have developed a working prototype of a dust sample collection device designed to determine if sufficient rock dust has been placed in an underground coal mine to prevent coal dust explosions. When used in conjunction with the Coal Dust Explosibility Meter (CDEM), the device will provide near instantaneous results on the quality of rock dusting at the tested location. The sampling device applies a pulse of air to a testing surface and collect a representative sample of mine dust based on the pneumatic entrainment process during a mine explosion. The use of both physical testing and Computational Fluid Dynamics (CFD) modeling has allowed researchers to refine the design to accurately represent the particle entrainment and optimize the sample size collected for the CDEM. The prototype is being tested in a mine environment to produce information of usability and practical aspects of mine dust sampling. This paper is a progress report summarizing the current status of sampler development. Researchers expect to have a fully developed and tested sampler in early 2016. INTRODUCTION Underground coal mines face the danger of methane and coal dust explosions. The disaster at Upper Big Branch mine (2010) has demonstrated the impact of a violent coal dust explosion that fatally injured 29 miners. Reviewing the history of coal dust explosions, researchers found that that mine operators and mine inspectors do not have a reliable method of collecting dust samples to assure that sufficient amounts of rock dust have been places to inertize the coal dust. This is a problem specifically with small mines that do not have dedicated safety departments to track rock dusting work. The aim of this research is to develop a simple, portable device that can help underground mine examiners collect dust samples from workings and test the explosibility of the sample near instantaneously. Researchers determined that the current brush-and-pan sampling method required by MSHA (MSHA 2013) is flawed in several aspects: Mechanical sampling with a brush exerts forces on the mine dust that may differ significantly from those present during an explosion. Also, U.S Bureau of Mines research (Nagy 1965) has determined that only the top 0.125 inches of the mine dust layer will be entrained in a coal dust explosion. Using a handheld pan and brush, it is difficult to correctly and repeatably sample a layer of this exact thickness. The following will describe the CFD modeling and experimental testing for the development of the prototype sampler. Researchers analyze the accuracy and performance of the prototype during the course of the build process."

Jan 1, 2015

By Weiguo Xie, Malcolm Powell, Lian Liu, Ping Yu

"In order to develop a common mathematical and simulation platform for tumbling mills, a review of existing mechanistic models was made identifying the key aspects of grinding and slurry transport which are common to all tumbling mills. A mill model structure has been developed for all types of tumbling mills based on the population balance framework by incorporating breakage characteristics, slurry and solids transport, product classification and discharge, and energy consumption. A size-dependant breakage model developed by the JKMRC is applied. Transport is separated from breakage events and treated as a main sub-model in the new model structure. The model structure is based on dynamic time-stepping technique to enable dynamic simulation capability for non-steady-state simulation and control modelling. It is envisaged that the new model will cover a full range of milling conditions. It should enable a smooth transition between different mill types, such as from AG (Autogenous Grinding) to SAG to ball mill. The dynamic mill model structure developed here is the first step towards mechanistic modelling of grinding mills and provides great potential for the optimization of the comminution process."

Jan 1, 2014

By A. Dale Marcy, Pamela L. Drake

Workers who perform routine welding tasks are potentially exposed to fume that may contain manganese. Manganese may cause respiratory problems and is implicated in causing the occurrence of Parkinson-like symptoms. In this study, a field colorimetric method for extracting and measuring manganese in welding fume was developed. The method uses ultrasonic extraction with an acidic hydrogen peroxide solution to extract welding fume collected on polyvinyl chloride filters. Commercially available pre-packaged reagents are used to produce a colored solution, created by a reaction of manganese(II) with 1-(2-pyridylazo)-2-naphthol. Absorbance measurements are then made using a portable spectrophotometer. The method detection limit and limit of quantification (LOQ) were 5.2 mg filter-1 and 17 mg filter-1, respectively, with a dynamic range up to 400 mg filter-1. When the results are above the LOQ for the colorimetric method, the manganese masses are equivalent to those measured by the International Organization for Standardization Method 15202-2, which employs a strong acid digestion and analysis using inductively coupled plasma-optical emission spectrometry.

By M. M. Masood, G. Y. Raju, T. Verma

The inverse velocity method has proven to be an effective approach for predicting slope failures in surface mines by analysing displacement monitoring data. However, the accuracy of inverse velocity method predictions is significantly affected by instrumental noise and natural environmental variations, which influence the identification of different deformation stages. To enhance predictive accuracy, this study applies and evaluates three filtering techniques to velocity time series data: Exponential smoothing filter, short-term smoothing filter, long-term smoothing filter and also compares it to raw data (no filtering). A refined prediction framework, that is, filtered inverse velocity method analyser, is proposed to improve slope failure forecasting in surface mining operations. The results demonstrate that filter selection plays a crucial role in optimising failure time predictions, offering valuable insights for geotechnical monitoring and early warning systems in surface mines.

Sep 1, 2025

By A. M. Thyer

Throughout the history of mining, underground fires or explosions have killed many hundreds or thousands of people. Fortunately, the safety record has gradually improved as a result of many people’s work on improving safety standards and work practices. However, fire and explosion still remains a threat in many situations. As a result the UK Mines Inspectorate commissioned a project to study materials used underground and to develop a fire/explosion risk assessment system. Such a system has been developed, following the study of incidents, specified fire resistance criteria, and fire safety practices. The final methodology uses a series of check sheets to identify potential fuels and ignition sources, preventative measures, fire/explosion mitigation systems, and items for inclusion in emergency plans.

Jan 1, 2003

By P. Mendoza, R. Siwale, H. Amini, R. Silva, M. Richards, V. Ngcoza, D. Rivera, C. Canaza, R. van Reenen

Development of a realistic flotation model to predict its performance is of paramount importance to the processing plant and operators, a model that accounts for predictive and no-predictive maintenance simulating individual equipment downtime and the effect of it in the metallurgical performance on the flotation bank with final recoveries and grades has a huge advantage on optimizing the flotation circuit/bank in terms of mechanical and metallurgical side. The Model was developed in a dynamic environment that allows for a better and more realistic simulation of the flotation bank. The maintenance model accounts for the Failure rate, Mean Time Between Failures (MTBF), Mean Time to Failure (MTTF) and Reliability (R(t)) those characteristics are combined to a multi-compartment process model that consists of a slurry recovery model, two options of froth recovery models, entrainment and carry capacity as a final check for the system. In addition to the maintenance and process model, a dynamic dart valve model was added to the simulation in order to have a realistic model to control the slurry level at the flotation cell. The paper goes over a study case for a current flotation operation trying to explore all the elements and the simulator to optimize the Rougher flotation bank.

Mar 2, 2022

By A. Vahed

The Goro Nickel Project is situated in the Southern Province of New Caledonia. Inco Limited and Goro Nickel S.A. have developed a process that features the use of pyrohydrolysis to produce nickel oxide. The process treats a blend of laterites by Pressure Acid Leaching followed by solvent extraction of nickel and cobalt using Cyanex 301®. Purified nickel chloride solution is converted to high purity NiO product and 6M hydrochloric acid, which is recycled back to the SX circuit. In co-operation with Andritz AG, spray roaster and fluid-bed pyrohydrolysis technologies were examined for this purpose. Tests were conducted at the Andritz AG pilot plant in Vienna, Austria, and at Goro in larger scale installations. The latter served to establish process engineering design parameters for scale-up. Several process variables were investigated in both technologies and the off-gas characteristics were established. Fluid-bed pyrohydrolysis was selected for the Goro commercial plant, primarily because it produced a granular nickel oxide. The main focus of this paper is to outline the results obtained in pilot plant studies of liquid fueled fluid bed pyrohydrolysis for the Goro Project. Keywords: lnco Goro Nickel, Fluid Bed Pyrohydrolysis, Pilot Plant Tests

Jan 1, 2004

By A. Nuric, S. Nuric, L. Kricak, M. Negovanovic, S. Mitrovic

"SynopsisRotary drilling with rolling tricone bits is the most widely used method for drilling large-diameter blast-holes in large surface mining operations. This drilling method is applicable to a wide range of soft to hard rock materials. This paper presents a fuzzy model for predicting the penetration rate of tricone rotary blast-hole drilling. The model is based on data obtained during the drilling of blastholes in rocks with various uniaxial compressive strengths in the Veliki Krivelj open pit mine, Bor, Serbia. The model was developed using the fuzzy logic toolbox of MATLAB with the Mamdani inference system. The fuzzy model was tested with 23% of the total dataset. The results obtained show the high reliability of predicting the penetration rates. Although there are possible limitations in applying the model to other open pit mines because of differences in rock properties, the prediction methodology applied in this paper can be used in many other predictions of the penetration rates.IntroductionAccording to Tamrock, rotary blast-hole drill operations depend on four important elements:•,Torque in the drill string drive sufficient to turn the bit in any strata encountered•,A high bit loading capability (pulldown force) sufficient for optimum penetration•,An air volume sufficient to remove chips generated during the drilling and to provide cool air to the drill bit bearings•,The selection of the proper type of bit for the material being drilled (Tamrock, 1984).The effects of rock mass parameters on the choice of the type of tricone bits were investigated by Kricak (1997)."

Jan 1, 2015

By S. Jeon, J. Kim, H. Lee

Though the importance of the engineering rock mass properties such as deformation modulus, cohesion and friction angle is emphasized, the researches on the reliability of these values are rarely performed. By using modified Takagi-Sugeno (TS) fuzzy inference system, a fuzzy model was developed based on the data obtained from domestic tunnel construction sites, and the ability of prediction was compared with the empirical equations conveniently used for estimating these values, which finds that fuzzy model is better than empirical equation. Sufficiently large database, however, is required for training the fuzzy model for more accurate prediction. Obwohl die Wichtigkeit der technischen Eigentümer der Felsenmassen wie zum Beispiel Verformungsmodulus, Bindekraft und Reibungswinkel betont werden, wird die Forschung auf der Zuverläßigkeit dieser Werte selten durchgeführt. Mit modifiziertem Takagi Sugenos (TS) Flaumigenschlußsystem wird die Flaumigenmodelle von den Daten, die von inländischen Tunnelbaustellen erhalten werden, entwickelt. Zum Schätzen dieser Werte ist es viel günstig, Flaumigenmodell zu benutzen, als zu adoptieren die empirische Gleichung für die Fähigkeit der Voraussage. Genügende große Datenbank wird aber zum Ausbilden flaumigen Modells für genauere Voraussage erfordert. Quoique l'importance sur la caractéristique d'ingénierie de la masse de roche comme le module de déformation, la cohésion et l'angle de friction, soit soulignée, la recherche sur la confiance de ces valeurs est rarement effectuée. Avec le système modifié de Takagi-Sugeno(TS) fuzzy inférence, le nouveau modèle fuzzy s'est développé. Après avoir estimé sa valeur, nous pouvons savoir que ce modèle fuzzy, basé sur les données venant du chantier de construction de tunnel national, est mieux que l'équaton empirique. Pourtant plus de données de base sont indispensables pour produire le modèle fuzzy plus précis.

Jan 1, 2003

By D. W. Alexander

Researchers from the U.S. Office of Mine Safety and Health Research (OMSHR) of the U.S. National Institute for Occupational Safety and Health (NIOSH) completed field trials during coal mine rescue contests using simulated gas detectors in place of placards. The gas monitor simulator (GMS) devices replaced static, paper placards to deliver gas concentration data. Eleven teams were observed during the field contest, which was approved by the Mine Safety and Health Administration (MSHA). GMS devices were given to three team members (the captain and both gasmen). Observation of teams revealed that team members changed behavior by acknowledging and sharing information more often while using the GMS. As a result of this research, it has been demonstrated that under the existing contest format, the newly developed GMS device may be used with no adverse impact on team contest performance. Furthermore, when GMS technology advantages are used, contest realism is improved. In the future, competency assessment may be incorporated.

Jan 1, 2012