Search Documents

By V. M. Hamza

Analysis of ground and airborne radiometric measurements in the Saquarema region (Rio de Janeiro) provides new insights into the breakdown and transport of mineral aggregates containing monazites, under sub-tropical weathering conditions. The breakdown process, accompanied by loss of low-density clay fractions in weathered materials is considered responsible for the observed patterns in relative enrichment of thorium and uranium along the migration paths of radionuclides. The characteristic features of these patterns provide clues as to the time and distance scales associated with processes of weathering and erosion. It is also possible to determine approximate locations of concentrations of accessory minerals. In this context, we advance the hypothesis that large under-water monazite deposits may be present along the offshore sand banks, in the coastal region of the state of Rio de Janeiro.

Sep 14, 2011

By John G. Groppo, James C. Hower, Cortland F. Eble, Rick Q. Honaker, Alireza Valian, Stephen F. Greb

Coal and coal combustion byproducts are potential candidates for alternative resources of REEs (rare earth elements). The Illinois Basin is a major coal-producing district in the USA, but little work is available on speciation of REEs in the basin’s coals. In this study, a total number of 382 samples from known locations in the Illinois Basin coal beds were acquired, analyzed for their REE contents, and investigated for any spatial trends or chemical correlations. This study includes Springfield, Herrin, and Baker coal beds—the most heavily mined coals in the basin. An average coal ash from the basin contains 320 ppm REE, with Baker being the highest (407 ppm on average). However, the distribution of REEs in the coal beds was laterally and vertically heterogeneous. A number of trends were found in the REE variations. The most important trend was the relationships of the REE concentrations and fractionations with the distance from the syndepositional sandstones. The total REE concentrations were higher in the proximity of the sandstones, likely due to the increased deposition of detrital material. This increase was the most significant in Springfield coal (90%) and least in Baker (6%). Those coal samples from the Springfield and Herrin coal beds distal from the syndepositional sandstones had a heavy to light REE ratio (H/L ratio) of 0.40 on average, whereas in proximal locations, the ratio was dropped to an average of 0.30. This trend was not significant in the Baker coal bed. In general, higher mineral matter in the coals was associated with higher REEs. In coal preparation plants, refuse rocks can have up to 360 ppmREE. However, the ashes of the cleanest coals had higher REE levels. Such ashes also have a higher ratio of heavy to light REEs. The highest REE concentrations were found in the claystones and the shales associated with the coal beds. Since the naturally occurring calcite, quartz, and pyrite samples were depleted in REEs, an association of REEs with the clay minerals can be suggested.

Jul 20, 2020

By N. Choi

The distribution behavior of selenium and tellurium in nickel sulfide smelting was investigated in the temperature range of 1250-1300 °C under an inert gas atmosphere and various oxygen partial pressures. The distribution coefficients of selenium and tellurium between nickel-copper-iron matte and silica-saturated iron silicate slag were detennined in terms of matte and slag compositions, temperature, and oxygen partial pressure. The effect of slag additives such as CaO, MgO, and Ah03 on the distribution coefficients of those elements was also investigated. It was observed that the distribution coefficients of selenium and tellurium increased with increasing matte grade and temperature. The solubility of selenium and tellurium in the slag decreased with increasing the partial pressure of oxygen within the range investigated in this study. The distribution coefficients of selenium and tellurium increased with the amount of CaO and MgO. Tellurium distribution coefficients also increased by the addition of Ah03. Meanwhile, the addition of Alz03 decreased the distribution coefficients of selenium at high matte grade.

Jan 1, 1996

By Alexander Hauck, Dimitri Jung, Uli Leiste

This paper describes results from small scale tests conducted to determine the distribution of impulse on target plates when subjected to loading due to the detonation of a buried mine. The tests were conducted with saturated sand, dry sand, and water as the loading media. Tests were conducted for flat plates and for plates with angled bottoms. Previous testing has shown that angled bottoms can reduce the total vertical impulse delivered to the vehicle significantly. Different stand off distances were investigated as well as loading of the targets both on center and off center. It is very important to know not only the total impulse delivered by a detonating charge but also how this impulse is distributed over the bottom of the vehicle. A complete understanding of specific impulse will permit those parts of the vehicle, taking the greatest amount of loading, to be sized properly. Experimental results were compared to analytical expressions provided by Westine and Tremblay.

Jan 1, 2010

By R. Hogg, T. F. Dumm

"A procedure for evaluating the size/specific gravity distribution of ultrafine coal and the distributions of sulfur and ash with respect to particle size and specific gravity is described. The procedure is essentially an extension of the conventional coal washability technique in which special precautions are taken to ensure particle dispersion in the heavy organic liquids, centrifuges are used to obtain adequate separation rates, and micromesh sieves are used for size separation at fine sizes. An example of the application of this technique to the evaluation of the extent of liberation of sulfur and ash in a coal sample ground to 90Z passing 200 mesh (74 um) is described.INTRODUCTIONIn order to determine the potential for deep cleaning of coal by fine grinding to liberate sulfur and ash-forming minerals, it is necessary to obtain data on the distributions of these species by size and specific gravity. In conventional coal processing operations, this information is obtained by means of a standard ""washability"" analysis. Attempts to extend this procedure to ultrafine coal, however, have generally been unsatisfactory and have often led to unreliable and inconsistent results [11. The present authors have described a modified washability procedure in which cumulative specific gravity fractionation is combined with sub-sieve size analysis (by laser diffraction/light scattering) to determine the particle size/specific gravity distribution of ultrafine coal [2]. Unfortunately, because this technique does not involve separation of the individual fractions, only limited information can be obtained on the specific distributions of sulfur and ash.The objective of the work described in this paper was to develop and evaluate a procedure for size and specific gravity fractionation of ultrafine coal and to use conventional analyses for sulfur and ash to determine their relative distribution in the coal. The procedure is essentially a simple extension of the standard washability analysis [3] but incorporating special precautions for treating ultrafine particles.EXPERIMENTAL Material The material used in the development and evaluation of the ultrafine coal fractionation procedure was a medium volatile bituminous coal from the Lower Kittanning seam. A sample of the coal (nominally - 1/4 inch), obtained from the Penn State Coal Data Base, was ground to 90% passing 200 mesh by the following two-stage grinding procedure: About 2 kg of the as-received coal were ground to about 30Z passing 200 mesh in a Model 4-E Quakertown mill (""coffee grinder""). About 1 kg of this product was then ground to about 90Z passing 200 mesh in a Holmes Model 300 Pulverizer."

Jan 1, 1989

By David A. Sterling

Approximately 50 percent of the uranium resource of the Free World is in deposits of Precambrian age, principally in lower Proterozoic conglomerates in Canada and South Africa (Uranium Resources, Joint Report, ENEA and IAEA, 1967). Most of the uranium resource of the United States is in Mesozoic and Cenozoic continental clastic sedimentary rocks that fill intracratonic basins. The Atomic Energy Commission is investigating the distribution of uranium and thorium in the Precambrian of the Western United States and the relationship of, time-space-facies patterns of uranium and thorium enrichment in the Precambrian to the major resources of uranium in the Mesozoic and Cenozoic host sedimentary rocks. This paper summarizes the results of preliminary studies of the Precambrian in the Southwestern United States including New Mexico, Arizona, southern Nevada, and southern California (Fig. 1). The host rock provenances for the major uranium resources in epigenetic deposits of Mesozoic and Cenozoic age in the Western United States were in areas of extensive Precambrian exposure along the eastern margin of the Phanerozoic geosynclinal belt (Fig. 2). Mesozoic continental clastic sediments in the Colorado Plateau contain about two-thirds of the uranium resource of the United States. These sediments formed from detritus derived from the Mogollon highland in the Southwestern United States where the Precambrian was extensively exposed (Stewart, et al., 19593 McKee, et al., 1959; McKee, et al., 1956; Craig, et al., 1955) (Fig. 2). A genetic relationship may exist between this provenance and the major uranium deposits of the Colorado Plateau. The Precambrian might be equally important in the genesis of uranium deposits whether the most important process in the formation of these deposits was the leaching of low-order intrinsic amounts of uranium from Precambrian granite or from Mesozoic pyroclastics derived from syntexis of the Precambrian basement rocks (Malan, 1968).

Jan 1, 1969

By R. Hogg, S. Chander

"The distribution of the wettability of coals of different rank was determined by measurements of contact angles for individual particles. The contact angle was estimated from the equilibrium partitioning of a particle at the water/air interface. Using this technique contact angles were determined for a larger number of particles from a given sample and a frequency distribution of contact angle was obtained. The contact angle distribution was broad for all the coals tested with included an anthracite, a hvA bituminous and a sub-bituminous coal. In comparison, spherical particles of polymethylmethacrylaie gave a much narrower distribution. The distribution for irregular polyethylene particles was somewhat broader than that for the polymethylmethacrylate spheres but broader than that for the polymethylmethacrylate spheres but considerably narrower than that for coal. The broader wetting distribution for coal was attributed to differences in surface chemical properties.INTRODUCTIONA knowledge of the wetting properties of coals is very useful in coal cleaning by flotation and other processes in which separations are based on differential surface properties. The various methods available for measuring wetting characteristics include: contact angle, 1-2 time, time, 3-5 bubble attachment, 6 film flotation,7 displacement pressure, 8-9 penetration rate, 10-11 bubble pick-up, 12 induction time, 13 imbibition time, 14 and calorimetry. 15-16 Of all these methods, however, the measure¬ment of contact angle by the sessile drop and captive bubble techniques have been most widely used. Brady and Gauger"" demonstrated through the use of the contact angle method that the natural hydrophobicity of coal varied greatly from sample to sample. Subsequent experiments showed that this difference correlated well with rank, the larger contact angles generally being associated with the higher rank coals. 18-19 More recent studies by Aplan and co-workers' show that the wettability of various ranks of coals as determined by sessile drop and captive bubble methods is a more complex function of rank. The hydrophobicity of coal usually increases with rank up to about 80% fixed carbon (dmmf) and then decreases."

Mar 1, 1992

By Rong. G., T. Q. Lin, W. Du

Based on analysis of the evolutionary history of the valley in Baihetan, the mechanism of asymmetrical evolution, gradual migration-incision evolved from left bank to the right, is revealed in Baihetan river valleys. The process of in-situ stress evolution is carried out by using the Universal Distinct Element Code (UDEC). Consequently, the numerical results which indicate the main regulations of that stress field are as follow: (1) The phenomenon termed "high in-situ stress fold" appears in the bottom of the valley. With the maximum principal stress being 28-34 MPa, the stress increases significantly at a vertical depth of approximately 130 m. (2) The in-situ stress presents zonal distribution along the bank slope. It is apparent that the in-situ stress field consists of stress relaxation zone (SRZ), stress concentration zone (SCZ) and original stress zone (OSZ). The horizontal depth of stress relaxation zone varies from the left bank (roughly 200 m) to the right (about 120 m). Furthermore, the stress evolution of the left bank slope is studied. As a result, it is found that asymmetrical erosion contributes to the difference of the in-situ stress distribution as a critical factor, between the left bank and the right. And for an asymmetrical valley, the evolutionary process of in-situ stress field is a circular procedure, which includes the incision of valley, the accumulation of landslides and the migration of valley.

Jan 1, 2015

By Tetsuya Yumoto, Toshikazu Shiratori

Information on the elements contained in E-Waste is important from the viewpoint of recycling. We analyzed several components of waste electrical and electronic equipment (WEEE) collected from citizens. The distributions of the minor metals in WEEE were determined with elemental mapping and chemical analyses. The annual change in elemental composition was investigated by analyzing equipment manufactured in different years. The information will be of use for separation techniques required for future advanced recycling.

Jan 1, 2011

By E. L. Brack

ASARCO's copper smelter at Hayden, Arizona has been upgraded to meet the increasing Environmental Protection Agency (EPA) and Occupational Safety and Health Administration (OSHA) environmental standards. Fortunately, means were found to accomplish these standards and provide for more efficient operations. With the adaptation of oxygen flash smelting and other related operations at Hayden, ASARCO has turned to the use of minicomputers and microprocessors for inter-plant communications and local area process control. The applications of distributive and computer controls to the plant operations at the Hayden smelter are discussed in this paper.

Jan 1, 1984

By W. Dziurzynski, St. Wasilewski, T. Palka, A. Krach

"Air parameter monitoring systems, regardless of gasometrical protections, provide a significant number of measurement data. The obtained data broadens the knowledge on processes taking place in underground workings and shows the relationships and influence of machines and technological processes on the variability of ventilation parameters in the areas of longwalls. Nowadays, computer simulation methods are increasingly used to reproduce the flow of air and methane mixture in the area of longwalls equipped with shearers. The paper presents the results of a research experiment covering a long-term observation of a longwall area during mining with a shearer using sensors from the mine's monitoring system. Data from sensors for methane concentration, pressure and velocity were used and additional ventilation measurements were taken to determine the parameters characterising the air flow in the area. The influence of different machine cycles in the longwall on the changes of air parameters in the area of the longwall was shown. A numerical model of the ventilation area was developed and the computer program VentZroby was used for the calculations, which allows for the simulation of the process of ventilating the area of the active longwall during the extraction of coal with the use of a shearer and haulage of the run-of-mine. Computer simulation of the influence of the shearer's operation and the methane inflow associated with the distribution of the mixture of air and methane was carried out. The results of the simulation were compared with the data recorded by the monitoring system’s sensors during the measurement experiment. Comparison of the recorded methane concentration courses with the results of a computer simulation of the air and methane flow conditions in the mining area showed changes in the gassiness. INTRODUCTION Studies carried out in the Polish and global mining industry show that methane is an obvious factor in limiting mining production due to the loss of continuity in the operation of longwall complexes in hard coal mines under methane emission hazard (Schatzel et al., 2008). In addition, methane hazards have a significant impact on the safety of the operators of machinery in the longwall. The requirements of Polish regulations and the practice of safe operation of mining longwalls require correct determination of gas concentration, volume flow, as well as pressure and temperature of the flowing air. As part of the research undertaken in the Budryk (Wasilewski, 2010) and Bielszowice (Dziurzynski et al., 2009) mines to assess the methane hazard in the longwalls and workings in the vicinity of the longwall, research experiments were carried out, during which air parameters were recorded by the mine monitoring system and additional testing equipment in different cycles of shearer operation."

Jan 1, 2019

By M. Robson

Water & Earth Technologies, Inc. (WET), Habitat Management, Inc. (HMI) and Chevron Mining, Inc. (CMI) together developed a solution for reclaiming steep southwest facing slopes in mining Area 12C that have historically been prone to excessive erosion, low vegetation establishment and continuing maintenance. Area 12C is located in the east wing of the Chevron McKinley Coal Mine, 27 miles northwest of Gallup, New Mexico, on Navajo Nation land administered by the Office of Surface Mining (OSM). Mining in this area was completed in May of 2007. Challenges encountered for this reclamation project included the need to reclaim graded material on a slope of 18-35% with southwest facing aspect, the presence of undisturbed rock outcropping that needed to be avoided during reclamation, the operational need to limit bulldozer pushes and the inability to import or export additional materials for construction. Two different reclamation alternatives were considered for Area 12C. The first alternative would use a traditional reclamation approach including three levels of draining terraces designed to convey water on a 3% slope to a single riprapped down drain. Terracing and down drains have been used to reclaim areas with similar terrain conditions elsewhere at the McKinely Mine and have failed to adequately control erosion (Williamson 2006). Terrace overtopping and down drain blowouts have been issues in maintenance and functionality for the mine. Maintenance routines consist of cleaning out terraces where they have filled in with sediment and repairing damaged or blown out terraces and down drains.

Jan 1, 2010

By William B. Plank

IN my studies during the past twenty years of the enrollments in the mining and metallurgical schools of the United States and Canada, I have been struck with the great diversity in the curricula offered by these schools. In 1933 when I made my first complete study of the schools (Mining and Metallurgy, May 1934, p. 211), I discovered 19 different curricula or programs of study, leading to almost as many different bachelor degrees, in the 49 schools in the United States and the 4 schools in Canada. These were: (1) Mining Engineering, (2) Coal Mining, (3) Metal Mining, (4) General Mining, (5) Mining Administration, (6) Mining and Metallurgy, (7) Metallurgical Engineering, (8) Metallurgy, (9) Petroleum Engineering, (10) Petroleum Refining, (11) Petroleum Geology, (12) Petroleum and Natural Gas, (13) Ceramic Engineering, (14) Ceramics, (15) Geological Engineering, (16) Mining Geology, (17) Economic Geology, (18) Geo- physics, (19) Fuel Technology.

Jan 3, 1950

By J. S. Marsh

TUESDAY, Feb. 16, was no day for strolling along the cold sidewalks of New York, and a large number of metallurgists sat down with pleasure to the warming task of wiping a few soldered joints. Presented by a joint-wiper of the modern school, G. M. Bouton, of the well-known team of Schumacher, Bouton, and Phipps, the initial paper brought into focus the theme of conservation of strategic metals and described the technique of making the fillet-type joint now employed by the Bell System. Using an over-all average of only 40 per cent of the solder formerly used by the conventional method. this important development bids fair to stick when the war is over. D. L. Martin and E. R. Parker then described the embrittling effect of hydrogen on silver previously heated in oxygen and the less serious but troublesome result obtained under the converse conditions. An interesting example of grain growth restriction created additional material for the lively discussion that ensued among those who have encountered one or another of these phenomena in silver and copper.

Jan 1, 1943

By A. G. Bulaev

Biohydrometallurgical technologies based on activity of acidophilic microorganisms oxidizing ferrous iron, sulfur, and sulfide minerals are widely used to extract base and noble metals from sulfide ores and concentrates. As sulfide minerals oxidation is exothermic, industrial processes are usually preformed at 40–50°C. Moderate thermophiles predominate under these conditions. Most of moderately thermophilic acidophilic microorganisms that oxidize metal sulfide are mixotrophic, i.e., they use both organic nutrients and CO2 as carbon sources. Carbon availability is crucial for microbial activity and affects efficiency of biohydrometallurgical processes. Aeration with CO2-enriched air is often used to increase microbial activity in biooxidation reactors. Organic nutrients can be used as alternative carbon source for moderately thermophiles performing biooxidation of sulfide concentrates. We performed several experiments with different sulfide concentrates to study effects of organic carbon sources on biooxidation efficiency and demonstrated that application of such organic nutrients as yeast extract (YE) and molasses made it possible to increase biooxidation efficiency. For example, addition of 0.02% YE in the nutrient medium increased biooxidation rate of pyrite–arsenopyrite gold bearing and chalcopyrite concentrates in batch mode at 45°C. YE addition increased oxidation rate of sulfide sulfur and gold recovery level from 65 to 87% and from 73 to 81%, respectively. Similarly, YE addition increased copper extraction from 47 to 54%. At the same time, YE addition increased efficiency of biooxidation of pyrite–arsenopyrite gold bearing concentrate in continuous mode. Without YE addition, oxidation rates of pyrite and arsenopyrite were 65.7% and 94%, while gold extraction was 71%. YE addition (0.02%) made it possible to oxidize 74% and 95 % of pyrite and arsenopyrite and extract 78% of gold. Addition of molasses (0.02%) similarly affected biooxidation efficiency. Thus, addition of organic nutrients in nutrient media is a promising strategy for improvement of biohydrometallurgical processes.

Jan 1, 2018

By G. Wozniak, R. Rostanski, H. Pfanz, G. Aschan, E. Sierka

"Industrial wasteland is a typical element of the landscape of all the industrialised regions in Europe. There are many examples from Poland as well as from other European countries that post-industrial sites have been undergone natural colonisation and succession to establish in some cases ecosystems of greater biological diversity than the original ecosystems. The post-industry sites regardless of any reclamation carried out, undergo natural successional processes. The respective biological diversity (number of species, and number of plant assemblages) reflects the micro-variety of the specific habitat. This paper summarizes the results of investigations, which have been carried out since 1989 on coal mine water sedimentation pools in the Upper Silesia Industry Region. The aim of this study is to demonstrate the diversity of spontaneous plant communities recorded on post-industrial waste sites. In the course of the long time fieldwork, plant assemblages representing nine phytosociological groups have been identified."

Jan 1, 2005

By J. Platt

Recent EPRI research on utilities? likely strategies to reduce sulfur emissions differs sharply from policy analyses showing all- switching or all-scrubbing choices. Energy Ventures Analysis, with Stearns-Catalytic and A. T. Kearney, estimated sulfur-removal costs for scrubbing or switching at virtually all affected plants in the 31 Eastern States. Cost tradeoffs occur between $30 and $40-plus per ton FOB mine in Central Appalachia ($33-44-plus per tonne). 1/2 to 3/4 of total sulfur reductions comes from scrubbing, whose costs act as a cap on low-sulfur coal prices. In a severe environmental scenario, low- sulfur coal demand evaporates, replaced by very low-sulfur (0.7%) coal demand. Additional findings and implications of EPRI coal supply and market studies will be reviewed.

Jan 1, 1987

By Scott A. Anderson, Benjamin S. Rivers, Derrick D. Dasenbrock, Silas Nichols

Unknown geotechnical conditions are a major source of risk. Unexplored places vastly outnumber the sampled and tested ones, and widely spaced boreholes with intermittent tests and samples are the norm. Sometimes site-specific planning and thought goes into locating these special, tested places, such as basing them on the geologic understanding or anticipated key locations for the structure; more often they are simply evenly distributed. We demonstrate a holographic model that allows viewers to see real data in real space, scaled or not, and to visualize where measurements are taken, what those values are indicating, and where there exists more unknown and more risk. The holographic model shows in an intuitive way, values from Standard Penetration and Cone Penetration tests, and surface geophysics. The mixed reality of this future is that a wide audience – owners, designers, project managers, contractors, and stakeholders interact together in a real space where they see and talk to each other, while at the same time are individually looking all around below or above ground, like a gopher, in a virtual one. Risk in the future will be better managed through more thoughtfully designed investigations and better communication of 3D data in a world of augmented reality. INTRODUCTION This paper explores the use of augmented reality to convey understanding of the subsurface conditions of a bridge site. This is in contrast with the current state of practice where this information is contained in a geotechnical report, and the ideas are also applicable to other structures, earthworks, and excavations. “Augmented reality” describes a situation where a 3D holographic model is displayed for users in such a way that the users experience both the model and the real environment of their setting- such as at a desk, in a meeting room, or in an open space at a project site (Figure 1). The 3D holographic model is used to directly visualize underground features, to see through the earth to the actual locations where explorations are made, samples are obtained, or measurements are taken, design values are assigned, or construction is planned. An immersive model provides the following three powerful functions for users:

Jan 1, 2019

By Albert J. Phillips

The effect of impurities on the flowsheet in the smelting and refining circuits for copper, lead and zinc is reviewed and the interflow of by-poduct metals from copper, lead and zinc plants is pointed out. The principal points of separation of all impurities in the circuits are indicated and the additional steps added to these circuits in order to effect impurity separation me shown. In this day and age, when difficult metallurgy is mentioned, one thinks of the extraction of more refractory or possibly the alkaline earth or rare-earth metals. It is true that the extraction of metals having a high affinity for oxygen and deleterious solubility for that element in the liquid metal, affords some of the most difficult extractive metallurgy problems. When this is coupled with an affinity for hydrogen, nitrogen, and carbon a devious approach is required that sometimes rivals the complexity of the metallurgy with which this paper deals. However, in all such cases the aim is for a simple

Jan 1, 1962

By L. M. Pidgeon

The reactive metals are above manganese on the electromotive series. Their compounds are characterized by large heats of formation and they cannot be reduced from their ores by classical methods. Three general production methods have been used: a) Fused salt electrolysis, b) reduction of a halide by another metal, and c) reduction of the oxide by another metal. Method (a) is highly developed, as in the case of aluminum, (b) in the case of titanium, and (c) has been successful in the case of volatile metals such as magnesium and calcium. It is suggested that future improvements will take place in (a), and particularly in (c), but are rather less likely in the case of (b). THIS year of 1963 is the centennial of the birth of both Charles Hall and of Heroult, the founders of the aluminum industry. Aluminum is the one reactive metal which has reached massive stature in modern industry and perhaps the only such metal to have been produced in any quantity before the turn of the century. It has been joined by others, some on a very modest scale, but all of importance and all of fascinating interest. When invited to give the Fifth Extractive Metallurgy lecture, it seemed appropriate to look back upon the short history of this group to trace the developments which brought extraction methods to their present state and, at great risk, offer opinions as to future trends.

Jan 1, 1963