Search Documents

By C. E. Williams, G. H. Bruce

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By Raffaella Granata, Daniele Vanni

"This paper presents the drilling and grouting program performed at two abandoned landfills located into former calcarenite rock quarries in Manfredonia, Italy. Tests performed after the abandonment of the landfills detected leachate infiltration into the groundwater, which required the implementation of a remedial program. In order to seal the rock fissures and create an impervious basin at the base of the two landfills, sub-horizontal boreholes were drilled and grouted into the rock under the waste deposits. At the same time, sub-vertical boreholes were drilled and grouted along the perimeter, to laterally confine the landfills. Finally, the landfills were properly capped with an HDPE membrane, geogrid, geotextile and topsoil. The methodology implemented to create a watertight barrier under the two landfills was innovative and cost-effective. Moreover, the drilling and grouting minimized the environmental impact of the remedial work, since the waste remained in their original location and were not affected by the remedial process.IntroductionThe two landfills, “Pariti-1 RSU” and “Conte di Troia”, are located approximately 6 km (4 miles) southwest of Manfredonia, a small town close to Foggia, Italy (Fig. 1). These landfills are located into two rock quarries, formerly used for the extraction of calcarenite (i.e., a weak calcareous sandstone, in tuff facies), and were abandoned in the early 90s. The two landfills cover a total area of about 45,000 m2 (11.2 acres), and mainly include urban solid waste with a depth of up to 25 m (82 ft). The main characteristics of the two waste landfills are listed in Table 1."

Jan 1, 2016

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days' rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

By H. C. H. Darley

Particles of montmorillonite-type clays consist of plate-like clay crystals stacked face to face. Under certain conditions in a suspension, these particles disperse to individual platelets with the formation of diffuse double layers round each platelet. This action has a profound influence on the rheo-logical and other properties of the suspension. This paper describes a test for degree of dispersion and uses this test to correlate changes in dispersion with changes in viscosity and gel strength. The test is of practical value in determining and controlling dispersion in drilling muds. INTRODUCTION It has long been recognized that the hydration and dispersion of clays, particularly those of the montmoril-loilite type, strongly influences the rheological and other properties of drilling muds, but little has been done to measure either of these phenomena under conditions that exist in drilling muds. The hydration of clays as such has been extensively studied by those interested in clay mineralogy, but in drilling muds it is to be expected that dispersion is at least as important a factor as hydration because of the much higher water-to-clay ratios and the very high degree of mechanical agitation. The term dispersion as generally applied to colloidal systems means the subdivision of large particles to small. Particles of montmorillonitic clays, however, consist of plate-like particles stacked face to face. Dispersion of these aggregates to individual platelets may be expected to have an unusually large influence on the properties of the suspension because of the shape factor, the enormous increase in specific surface, and the pronounced surface phenomena exhibited by the crystal surfaces. It is this form of dispersion that is particularly considered in this paper, -and the term degree of dispersion is used to imply the number of platelets per particle. The term aggregation is used to denote the opposite of dispersion, the association of individual platelets face to face to form stacks. It is important, as Garrison' has pointed out, to distinguish between the deflocculation-flocculation phenomenon and the dispersion-aggregation phenomenon. Flocculation of clay suspensions is characterized by the formation of voluminous sediments that are stable under quite high centrifugal fields. This indicates an edge to plate association of particles to form an open network type of structure, which obviously will have quite a different influence on the properties of the suspension than aggregation of the platelets face to face. The work described in this paper was primarily concerned with developing a test for degree of dispersion in clay suspensions and by means of this test to follow changes of dispersion brought about by addition of electrolytes and to show the influence of dispersion on the rheological properties. The Clay-Volume Test This test is based on the assumption that the greater the number of particles per unit weight of clay in a suspension the greater will be the volume of sediment when it is flocculated under standard conditions and centrifuged. After considerable experimentation the following procedure was established: 1 cc of the test mud vigorously shaken with 100 cc of 1-N NaCl in an ASTM oil centrifuge tube and centrifuged for five minutes in an International No. 2 centrifuge at 2,000 rpm. When drilling fluids of different solids content are being compared, the clay volume is expressed in cc per gram of clay solids, but generally changes in dispersion in a given mud are being compared and it is more convenient to report as cc of sediment. The test is strictly a comparative test, so that it is not necessary to adhere to the conditions specified above, e.g., with field muds a stronger flocculant such as Al2(SO4)3 may be preferable to NaCl.

Jan 1, 1958

By F. H. Deily, L. W. Ledgerwood, J. E. Eckel

A new method for drilling the earth's formations has undergone extensive laboratory and shallow earth drilling experimentation. This method, pellet impact drilling, uses the energy of a large mass of high velocity steel spheres to break and crush the rock. Pellets are confined to a region close to the hole bottom. Motive fluid for transporting and recycling the pellets is supplied by a modified jet pump. The pellet drilling method has inherent advantages over conventional rotary drilling. First, only a nominal amount of weight need be applied to the hole bottom. Second, only a very small amount of torque is required for bit rotation. Third, means are available for continual replacement of the cutter medium. The experimental laboratory work and analytical procedures necessary for the design of a pellet drill bit are described. In the laboratory program approximately half the effort was devoted to the development of a better understanding of the physical process, and half to the empirical testing of new bit configurations. Factors such as pellet size and velocity, jet pump characteristics and modifications, and power distribution are discussed. The design and construction of a pellet impact bit for drilling a 9 in. hole with 1 1/4 in. steel pellets are described. Drilling performance in representative rocks, hydraulic operating characteristics, and metallurgical problems are discussed. INTRODUCTION This paper discusses an attempt to reduce drilling costs through the development of a drilling method basically different from rotary drilling. Publications on drilling research indicate that the major effort on the part of manufacturers and operators has been confined to research in rotary, or rotary-percussion drilling. This applied drilling research has produced significant gains in drilling rates and bit life, but thus far it has failed to achieve any major decrease in general drilling costs. From recent statistics released by Drilling Contractors, it can be shown that the total cost of drilling an "average" well in 1953 was about 2 1/4 times the corresponding cost in 1935. Analysis of the costs will show that they are not due to inefficient field operations; they are due instead to both an inflated economy and greater "average" well depths. Diligent work by the industry has reduced the backlog of potential economic improvements in rotary drilling to a group of rather marginal prospects. Increasing depths and poorer quality reservoirs at these depths continue to make the drilling cost problem more acute. Hence, the aim of the work reported here was to develop a new drilling method not limited by the inherent characteristics of rotary drilling and thus capable of attaining further significant reductions in drilling costs. The effort devoted to research on this proposed new drilling method was of considerable magnitude and represented .in excess of 37 man-years of research. The affiliates of Standard Oil Co. (N. I.) sponsored this development program which was conducted by the Drilling Methods Section of the Carter Research Laboratory in Tulsa, Okla. The purpose of this paper is to

Jan 1, 1957

By C. D. Cochran, F. H. Deily, M. M. White, Victor Horner

A laboratory study of the effects of physical and easily measured rheological properties upon dynamic filtration was carried out. The purpose was to determine the factors affecting dynamic filtration and thus learn how to control this important property. The recommended procedure for determining the amount of fluid loss prescribed by API Code RP 29 "Field Procedure for Testing Drilling Fluids,"' is very useful for mud conditioning purposes, but inadequate for comparing filtration properties of different muds under dynamic conditions. Where dynamic filtration control becomes important for purposes such as logging and coring, other means of evaluating filtration properties are needed. A special device and testing technique were developed to provide reliable data on filtration characteristics of different fluids under dynamic conditions. Liquid saturated rock samples were drilled with a microbit, and the amount of connate liquid displaced by the fluid being investigated was measured. The empirical testing procedure was considered reliable. A large number of laboratory-prepared and field-mixed dritling fluids with a wide range of physical properties were studied. These properties included: (I) shape of consistency curves, (2) apparent viscosity, (3) plastic viscosity, (4) yield value, (5) density, and (6) API filter loss. Test results indicate that very little, if any, trend could be established between changes in these fluid properties and dynamic filtration. INTRODUCTION During the process of drilling, excessive loss of liquid from the mud to the formation is undesirable for many reasons. Filtration can reduce production-zone permeability, cause sloughing of formations, affect electric log curves, and render the fluid data obtained from cores unreliable. Thus, it is very important that we gain a knowledge of the factors that control filtration. It is generally agreed that in any type of filtration (static, dynamic, or combinations thereof), the mechanics of filtering depend in great part upon the composition of the fluid. Moreover, it is also true that the physical and rheological properties are influenced by the composition of the fluid. Indirectly, then, it was hypothesized that a relationship existed between dynamic filtration and physical-rheological properties, two effects of a common cause—fluid composition. This paper discusses an attempt to relate filtration-while-drilling to physical and easily measured rheological properties. It is believed that the results of this study may prove useful to others in the industry who are working on the problem of understanding filtration. The industry accepted practice for determining fluid loss from drilling mud is described in API Code RP 29. The practice is to measure the amount of filtrate that passes during a given interval of time from a quiescent drilling fluid under applied pressure through a piece of filter paper. This is primarily a test of static filtration properties. Other investigators have studied filtration under dynamic conditions. Williams5 and Pro-kop5 studied radial filtration and filter-cake buildup by circulating fluid through a porous cylinder under conditions similar to actual mud flow. Nowak,4 Krueger,3,4 and Vogel3 studied the effect of filtration upon permeability by flowing mud past the face of rock Samples. In their tests, the bit action was simulated by mechanical scrapers that kept the filter cake from building up. Ferguson and Klotz2 studied three types of filtration: static, dynamic, and beneath-the-bit. They investigated each type separately, using a model well in which bottom-hole hydraulics and mechanics were closely approximated.

Jan 1, 1958

By R. A. Generes, H. C. H. Darley

Laboratory tests showed that at elevated temperatures a reaction takes place between all metal hydroxides and clay muds, which results in a thickening or solidifying of the mud, the extent of which depends on the nature of the ingredients. Calcium hydroxide gave the strongest solidification whereas barium hydroxide only caused a mild thickening, indicating that the use of barium hydroxide muds instead of lime muds would be a good way of preventing high-temperature solidification. It was found possible to prepare barium mud in the laboratory with caustic soda and a thinner in the same manner as lime muds, and these barium muds had the same or better toleration of high solids content, resistance to salt contamination, and low gel strengths as the corresponding lime muds. Three field trials have been made with barium mud. The principal difficulty encountered was in determining the correct proportions of the tourly treatments required to maintain low gel strengths. A satisfactory systern was finally developed, and low gels were maintained throughout the third test. The wells on which the trials were made were not carried deep enough to test the resistance to solidification adequately, but oven tests at 350°F were made periodically and no tendency to solidification was noted except immediately after severe cernent contamination had introduced excessive amounts of calcium into the system. Although barium hydroxide costs considerably more than lime, the total mud costs were as low, and on the last well significantly lower, than the average cost of lime mud wells drilled in the vicinity. INTRODUCTION The advantages of repressing dispersion and hydra-tion of clay cuttings carried in the mud, particularly when drilling through thick clay formations, are well recognized. This repression is generally achieved by the use of lime, and lime muds have in consequence the desirable characteristics of high toleration of solids, low thixotropy, and good resistance to contamination. They have, however, the disadvantage of high-temperature solidification. This phenomenon has been described in detail by Gray et al, who have shown that it is the result of a chemical reaction between the hydroxides and the clay minerals. The work described in this paper was undertaken to find a substitute for lime which would not cause this solidification. LABORATORY EXPERlMENTS The principal positive requirement for a substitute for lime is that it should repress the hydration and dispersion of clay. It is well known that monovalent cations promote hydration while polyvalent cations repress it. Therefore, a few representative polyvalent salts and hydroxides were tested to determine whether they could be used as substitutes for lime. Their efficiency at repressing hydration and dispersion was measured by means of the clay-volume test. It has been shown elsewhere' that this test is a good measure of degree of dispersion of clay in suspension and that hydration accompanies and correlates with dispersion, so that measuring one measures the other. The test is made by centrifuging a 1:100 mixture of mud and 1-N NaCl and observing the volume of sediment—the greater the volume, the greater the dispersion. The tendency to caux solidification was measured by heating the muds in pressure vessels for 16 hours at 150°F and 370°F. An approximate quantitative

Jan 1, 1957

By R. R. Angel

Drilling rate is a parameter that should be considered in determining the volume requirements for air and gas drilling. The use of past methods which ignore the effects of the solids content upon the pressure and velocity of the annulus flow stream can result in undercalculation of the required volurne by as much as 50 per cent. A vertical-flow equation is presented for determining volume requirements. This equation includes the effect of the solids that are transported up the annulus in the flow stream by incorporating the drilling rate as one of the parameters. The effect of down-hole temperature on required circulation rates is also ana-lvzed. A simple approximate method of determining volume requirements is presented. This method is more accurate than the methods used in the past. Hole cleaning difficulties are analyzed for a recent air drilling job where past methods indicated that - excess air was being used. Sample curves of calculated boitom-hole pressures are presented for air and gas drilling in several hole sizes. INTRODUCTION In certain areas the use of air or natural gas as a circulating medium for drilling oil and gas wells is becoming a common practice. Large increases in penetration rate and bit life are achieved through the use of these media in preference to mud or water. Drilling rates as high as 90 ft/hr have been obtained in shales. The importance of maintaining adequate circulation rate is generally recognized; however, much disagreement exists among drilling operators as to what constitutes "adequate" circulation rate. In quarry drilling, where annular velocities can be accurately determined, an annular velocity of 3,000 ft/min of standard air is required for best results in rocks having approximately the same density as those commonly penetrated in drilling oil or gas wells'. Although this standard air velocity has proven satisfactory for quarry drilling, some oil and gas well drilling operators believe that an equivalent annular velocity of more than 4,000 ft/min is required; others believe that as little as 2,000 ft/min . is sufficient. Much of this disagreement results from determining the required circulation rates with methods which fail to incorporate the drilled solids in an equation which is applicable to vertical flow. Hughes Tool Co. Bulletins No. 23' and 23-A3 present data for determining circulation rates based on the Weymouth formula. These data do not include the drilling rate as a parameter and, therefore, neglect the effect of the solids being transported up the annulus. In spite of this apparent defect and the fact that the Weymouth formula is not applicable to vertical flow, the Hughes data have well served the drilling industry in many areas and are important and timely contributions to the science of air and gas drilling. The Hughes data purposely omit a correction for increasing down-hole temperature. At slow drilling rates this effectively compensates for the use of a formula which is not valid for vertical flow; however, volumes determined by the Hughes method are not sufficient to support rapid drilling rates at moderate and great depths. For example, Phillips Petroleum Co.'s Cauthorn "D" No. l in the Vinegarone field for Val Verde County, Tex., was air drilled from 1,500 to 9,300 ft using a compressor delivering 1,400 cu ft/min. The 8 3/4-in hole was drilled with 5-in. drill pipe, and drilling rates as high as 90 ft/hr were obtained between 7,000 and 9,300 ft. No water or caving hole was encountered. At 7,728 ft it was necessary to wash-out 60 ft of cuttings to reach bottom after a trip to change bits. At 8,130 ft a twist-off occurred and the drill col-lars were stuck in drill cuttings. These difficulties indicate that the 1,400 cu ft/min of air was not sufficient to keep the hole clean. Hughes data indicates that 1,180 cu ft/min is sufficient to produce an annular ve-

Jan 1, 1958

By Albert D. Brokaw

The accompanying charts are presented to extend and improve a chart published under the title "A Chart to Provide Approximate Correction for Temperature and Deviation from Boyle's Law."' The applicability of this earlier chart was limited by the fact that it was based on the work of Burke and Keyes² and Kvalnes and Gaddy3 whose experiments were conducted with pure methane, the adjustments suggested for natural gases of higher specific gravity were unsatisfactory except within limited ranges of temperatures and pressures, and precise interpolation was difficult. The extensive work of G. G. Brown, D. L. Katz and their associates on the heavier natural gases has provided better bases for the needed corrections, and the present charts. which are based largely on their work, are intended to simplify the computations involved. The design of the charts has been changed by plotting temperatures as a function of pressure and correction factor, on a semilogarithmic or "ratio" grid, which gives fairly even spacing of the graphs and simplifies interpolation. Charts have been prepared for natural gas with specific gravities of .60, .65, .70, .75 and .80. The standard computation for use in estimating the quantity of gas in a reservoir may be expressed as follows: _ PA X 520 X VR ZT where: Q is the volume of gas at 60°F and one atmosphere pressure PA is the absolute formation pressure in atmospheres

Jan 1, 1949

By Albert D. Brokaw

The accompanying charts are presented to extend and improve a chart published under the title "A Chart to Provide Approximate Correction for Temperature and Deviation from Boyle's Law."' The applicability of this earlier chart was limited by the fact that it was based on the work of Burke and Keyes² and Kvalnes and Gaddy3 whose experiments were conducted with pure methane, the adjustments suggested for natural gases of higher specific gravity were unsatisfactory except within limited ranges of temperatures and pressures, and precise interpolation was difficult. The extensive work of G. G. Brown, D. L. Katz and their associates on the heavier natural gases has provided better bases for the needed corrections, and the present charts. which are based largely on their work, are intended to simplify the computations involved. The design of the charts has been changed by plotting temperatures as a function of pressure and correction factor, on a semilogarithmic or "ratio" grid, which gives fairly even spacing of the graphs and simplifies interpolation. Charts have been prepared for natural gas with specific gravities of .60, .65, .70, .75 and .80. The standard computation for use in estimating the quantity of gas in a reservoir may be expressed as follows: _ PA X 520 X VR ZT where: Q is the volume of gas at 60°F and one atmosphere pressure PA is the absolute formation pressure in atmospheres

Jan 1, 1949

By C. W. Binckley, F. R. Burgess, E. R. Haymaker

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By E. R. Haymaker, C. W. Binckley, F. R. Burgess

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By Arthur Knapp

No oil territory in the world has been so rich in large producing wells, in a comparatively small area, as the Baku field. Particularly is this true of the Bibi Eibat field, which formerly produced millions of "poods," of " gusher," or as it is called in Russia, " fountain " oil. The Bibi Eibat and Balachany fields have been exhausted of gas and ruined by water, but the Surachany and Benegadi fields are still fountain territories and many outlying districts that have only been prospected produce rich fountains. The method of controlling fountains, or gushers, is the result of growth, along with the Russian system of drilling, where large diameters and riveted casing have been in vogue. The screw casing is seldom used except to exclude water. Formerly the method of finishing wells and the condition of the casing at the top of the well would not permit the use of gates, manifolds, and connections as is standard elsewhere. The life of the flowing wells is very short, particularly those 10 in. (25 cm.) or more in diameter, which produce large quantities of sand and often flow for but a few days and are then a complete loss. More than 1,000,000 poods in 24 hr. have been claimed in several instances, but in no case was the flow for more than a few days. The oil sands of this district are free uncemented sands and vary in thickness from paper thin to a maximum of 10 ft. (3 m.). The sands are interlaid with strata of soft clay. In spite of this, the practice has been to drill into such sands and produce from the open hole without screen or liners. Sometimes the casing is set below the oil sand but in this case holes from 2 ½ to 3 in. in diameter are drilled opposite the oil sand, which would not have the effect of a screen.

Jan 1, 1920

By A. P. Wickland

The characteristic problems related to drilling a hole for evaluation of an orebody are generally quite similar, whether we're drilling a core hole, or a hole to obtain chip samples. The basic objective in each case is fundamentally an economic factor; to produce the maximum amount of usable information per hole at a reasonable footage price. The success of the drilled hole depends largely upon the amount of investigation and research spent on the prospective area and the ability to forecast the capable personnel needed plus the right kind of drills, ancillary equipment such as bits, muds and various additives necessary to make the drilling program successful. The driller is confronted with a wide variation of drilling problems due to the nature of subsurface conditions. Some of these problems are: overburden, which may consist of clays; sand; boulders; or glacial till. These surface conditions may exist up to 2,000 feet in depth and upon reaching bedrock, formations may consist of swelling shales, broken sandstones, and every conceivable rock-type, coupled with every known structural problem such as dips, faults, folds, etc., and to this added extras such as permafrost and/or ground water problems combine to increase the necessity why an understanding of the problems along with the proper reaction of the driller plus the formula to compensate for ground conditions is necessary to complete a drill hole. Since most geologists are familiar with diamond core drilling techniques, I would like to discuss other methods used in evaluating ore deposits.

Jan 1, 1973

By Leon W. Dupuy

Many articles have been written describing peculiar and particular types of drilling. Little correlation has been made between the character of ground to be drilled and sampled and the type of drilling most desirable for procuring satisfactory samples. In development work, the engineer and metallurgist often desire the recovery of a sample in as physically natural a condition as possible, particularly when the sample must provide material for process tests as well as chemical and physical analyses. This paper describes the results of experimentation in drilling unconsolidated materials carrying titanium minerals in the Magnet Cove area, Ark. The drilling was most difficult in that the ground varied much in consistency, and it was vitally necessary to recover a physically natural sample. Ordinary churn drilling recovered a sample that could be analyzed chemically, but the sample was not in its natural state. The problem was successfully solved by utilizing and further developing methods used in the oil and clay industries.

Jan 1, 1949

By Elton A., Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11 mile bus ride up Railroad Creek to Holden. All freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting.

Jan 1, 1949

By Roscoe C. Clark, Henry F. Coffer, J. J. Reynolds

A cement slurry lightweight additive has been adapted in the Conoco laboratories for use in oil well cements. This additive makes possible the use of air to lighten oil well cement slurries. Specifically, the additive consists of small clay bubbles of air having sufficient strength to resist crushing by bottom hole pressures. Clay bubble cement slurry weights can be safely reduced to 10 Ibs/gal. In addition, the clay bubbles tend to act as lost circulation materials and to provide a cement texture which should produce good perforating characteristics. Clay bubble cement is relatively impermeable. INTRODUCTION In many areas in Oklahoma, Texas, Wyoming, and California, difficulties are experienced during casing cementing operations with lost returns caused by the high density of the cement slurries. Wells in these areas are ordinarily drilled with 9 to 11 lbs/gal. drilling mud while neat cement slurries may range in densities from 14.5 to 17 lbs/gal. In these areas, cement slurry weights are at present being successfully reduced to around 12 lbs/gal. (under bottom-hole conditions) by the use of additives in the cement. Since the use of additives will decrease the strength which the cement will develop, the amount of additives which can be used must be based on the minimum cement strength which is acceptable; and thus the maximum slurry weight can be reduced. At present, the minimum tensile strength generally acceptable is 50 lbs/sq in. cured for 24 hours under bottom-hole temperature. This figure is based on laboratory tests1 and on a large number of cement jobs which have been conducted using cement which will not develop more than 50 psi tensile strength in 24 hours under bottom-hole conditions. Two additives are now in use for decreasing cement slurry weights. These are expanded perlite and/or bentonite. The density of both of these materials is greater than that of the cement slurry; however, large quantities of water may be added with these materials without producing a slurry which will settle out of suspension. It is these large quantities of water which contribute to the reduction in the slurry weight. The minimum slurry weight at present obtainable with expanded perlite and/or bentonite is approximately 12 lbs/gal. using a standard Portland cement slurry. In many areas, this weight reduction is insufficient; and returns are still lost during casing cementing operations. In many cases, the pay formation itself is fractured; and a considerable quantity of this cement is lost to the pay zone. It is therefore believed that if cement slurry weights can be reduced to as low as 10 lbs/gal., two advantages will accrue: 1. The lighter densities (10 to 12 lbs/gal.) should mitigate or eliminate lost returns during casing cementing operations. 2. Cement slurries above 12 Ibs/gal. (the present minimum limit ) should develop considerably more strength than is now being obtained. A tensile strength of 100 psi is desirable.' It is the object of this paper to describe a cement slurry having a weight of 10 lbs/gal. and capable of

Jan 1, 1955

By C. K. Ferguson, J. A. Klotz

This paper describes experimental investigations conducted at the California Research Corporation's model oil well. The first part describes filter loss from several drilling muds through bore hole walls during mud circulation and drill string rotation. The effect of mud properties and drill string rotation with mud circulation is described. Filtration from a bore hole full of drilling mud, not circulating, but under pressure for extended time periods, is also discussed. The second part describes filter loss to permeable formations from beneath a drilling bit where filter cuke has no opportunity to develop appreciable thickness. If potential flow theory is applied to predict filtrate invasion from this hole bottom, targe invasions arc calculated. But model well experimentation shows that filtrate invasion from the hole bottom is controlled by mud particles that penetrate the formation ahead of the bit. This experimentation provides data to estimate the effect of mud particle penetration on fluid loss to formation. The third part presents an estimate of mud filtration during drilling of a well. INTRODUCTION As oil wells are drilled by the rotary method, drilling mud circulates up the annulus between drill pine and well wall. Drillers adjust mud density so that the pressure at the bottom of the mud column is several hundred psi greater than the pressure of reservoir fluid. As a result of this pressure difference, the liquid part of the mud filters into the rock around the bore and mud solids deposit as a filter cake on the well wall. For many reasons the petrogleum industry, within the past 20 years, has spent much money and energy to determine the volume of mud filtrate that enters rock around the well bore and dedicated much research effort to reduce this volume. Among the reasons for attempts to determine the volume of mud filtrate and to reduce this volume are the following: 1. If filtrate damages the permeability of oil sand, the resultant damage to oil well productivity will depend on the distance that the filtrate invades the oil sand; reduction of filtrate volume may, therefore, increase well productivity. 2. Filtrate that penetrates shale sections may cause the shale to swell and to slough into the well bore. Uncontrolled sloughing may stick drill pipe. Reduction in filtrate volume may reduce drilling trouble. 3. Electric log resistivity curves are changed by invasion of a mud filtrate; the change depends on the depth to which filtrate invades. Knowledge of this depth is necessary before resistivity logs can be interpreted accurately. For these reasons, specifications the place an upper limit to drilling mud filter loss are now written into almost all drilling programs. These specifications are based on APT Recommended practice 29, Standard Field Procedure for Testing Drilling Fluids,' which describes a static filtration test operated at 100 psi filtration pressure and at ambient temperature. Although this test is adequate for mud control, it cannot be used to compare filtration properties of different muds. Schremp and Johnson' showed, for example, that mud with a low API filter loss does not necessarily have low filter loss at bottom hole temperature and pressure. Also, no information has been available about the effect of bottom hole mechanics (mild circulation, drill string rotation, and bit action) on mud filtration. This paper discusses filtration data measured in the California Research Corporation's model oil well, which models closely oil well bottom hole geometry and hydrodynamic conditions. The filtration processes that

Jan 1, 1955

By Joseph J. Larry

In hard siliceous sandstone strata overlying coal seams, roof bolting is often the bottleneck in the coal production cycle. In the past, these strata have been drilled by pneumatically operated stopers. Although slow drilling is cumbersome and uncomfortably noisy, the stoper was the most effective drill in these harder strata. However, because of the (U.S.) Coal Mining Safety Act, which limits noise levels for operating drills, FMC Mining Equipment developed the water-through-the-drill-steel method of drilling high-compressive-strength strata. Although water-through-the-drill steel had been developed earlier, the real impact of wet drilling techniques surfaced when the dual-boom roof drilling machines were installed at the Virginia-Pocahontas Division, Keen Mountain, Virginia, in 1974. This paper covers some of the technical details of the water-through- the-drill-steel design and its application.

Jan 1, 1979