Search Documents

By Raphael G. Kazmann

The predicted warming of the earth's surface, presently the subject of much debate, controversy and legislation, is based on what is termed "the greenhouse effect." This is the result of the property of certain atmospheric gases. These gases allow the passage of radiant energy to the earth's surface and reflect back, to the earth, the infrared radiation given out by the heated surface. Physicists have computed that if there were no greenhouse effect the average temperature of the earth, now about 15° C (60T), would be close to -18° C (OT). Just what gases have produced this salubrious effect? Water vapor is the most important. Then come carbon dioxide, methane and a number of minor constituents of the atmosphere, both natural and man-made. Climate change, its cause and its impact on human activities have been the subject of scientific and historical study for more than a century. Recently, some scientists have concluded that if the man-made increase in the carbon dioxide and other greenhouse gases continues, by the late 21st century the earth's global average temperature will rise between 2° to 8° F. This temperature rise would cause the water in the oceans to expand and the massive polar glaciers to melt. In 1980, it was predicted that the sea level would rise 7.6 m (25 ft) by the late 21st century. By 1985, the predicted rise was 1 m (3 ft); and by 1989, it was 0.3 m (1 ft) (Jastrow, Nierenberg and Seitz, 1990). Agricultural scientists have pointed out that an increase in atmospheric carbon dioxide would enhance biological growth including the production of foodstuffs.

Jan 1, 1992

By AIME AIME

IV. THE BOUNDARY BETWEEN STEEL AND IRON. It would be well to decide on a definite carbon-content to serve as a boundary line between ingot-iron and ingot-steel, between puddled-iron and puddled-steel, and between any other varieties of wrought-iron and weld-steel. Two plans have been considered. One is to draw this line at 0.32 per cent. of carbon or its equivalent in other elements, for the reason that this carbon-content appears to correspond to the critical point, 0, in the diagrams of Roberts-Austen and Rooze-boom.8 This has the merit of corresponding to a definite physical boundary. The other plan is to draw the boundary at 0.20 per cent. of carbon, because this is a convenient place to separate the important classes " soft steel " and " half-hard steel," so that if this point was adopted "ingot-iron " would be synonymous with "soft steel," and " ingot-steel " would be the equivalent of the two classes, " half-hard steel " and " hard steel."

Mar 1, 1908

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency has been widely used by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which follows. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided. The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies. OUTLINE Introduction and Background Part 1. Determining the Bond Efficiency of a Grinding Circuit Method Demonstration/Example Calculations Bond Work Index Testing Equipment and Procedures Accuracy of Comparative Circuit WI Efficiency Determinations (under development) List of Symbols Part 2. Data Base of Bond Grinding Circuit Efficiencies (under development) References Annexes: A1. The Bond Crushing WI Test Equipment and Procedure for Bond Efficiency Determinations (Revised March 26, 2015) B1. The Bond Rod Mill WI Test Equipment and Procedure (Revised March 26, 2015) C1. The Bond Ball Mill WI Test Equipment and Procedure (Revised March 26, 2015) Introduction and Background Please see the references and slide presentation “Bond Efficiency SLC (rev3)-print.pdf.” This efficiency determination applies to most brittle materials in their naturally occurring (un-scalped) size distributions being treated in size reduction circuits down to a product sizing of approximately eighty percent passing 70 µm (see below). Unusually shaped materials (e.g. mica) should be regarded with caution. Part 1. Determining the Bond Efficiency of a Grinding Circuit Method In the plant: • Define the circuit for which the WI efficiency is to be determined • Procure samples of the circuit feed and product • Obtain the power draw of the size reduction equipment at the drive pinion(s) • Obtain the circuit throughput rate (dry tonnage) In the laboratory:"

Jan 1, 2016

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By C Hawtin, B Miller, D Ashton

Ernest Henry mine (EHM) is an Iron oxide copper-gold sublevel cave mine located 30 minutes north of Cloncurry in North-West Queensland. The underground mine lies beneath open pit excavations, which were in operation from 1999 to 2011. Fault structures carry large quantities of water from the cover sequence aquifer into the underground mine area. The open cut excavations exacerbates vulnerability of the underground mine to the high intensity wet season storms of northern Queensland. These factors combine to make hydrogeological issues high priority for mine operation. Water-related risks include the cost of removing water from the mine, flooding risk and mud rush potential.Turnover of key technical staff in late 2015 at EHM resulted in the mine being left in an untenable position of losing the primary source of technical knowledge. Due to encouragement of cross-disciplinary activity coupled with workload and resource sharing, the management team were confident in utilising on-site personnel to offset loss of experienced personnel.Remaining geology personnel took additional responsibility for hydrogeological monitoring equipment and planning of upcoming work. Consultant input was limited to review only and an emphasis was placed on knowledge transfer to the geology team. Using this strategy, a 13 hole dewatering program was successfully implemented, achieving a significant water level drop in areas of elevated hydrological risk, whilst also upgrading the hydrological monitoring sensor array.Through a development program centred on cross-disciplinary exposure, the technical team was able to retain key technical knowledge despite staff turnover and produce strong results outside traditional training and roles. This paper serves as a case study on the methods, strengths and drawbacks of putting a focus on cross-disciplinary exposure as a method to combat staff turnover.CITATION:Ashton, D, Miller, B and Hawtin, C, 2017. Go with the flow – managing hydrogeological staff turnover at Ernest Henry mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By M Brady

"It has long been recognised that the barometer infl uences areas of underground coal mines that havebeen sealed off from the current, or active, mine workings but it appears litt le formal research hasbeen done on how the barometer aff ects the goafstream sample point. Based on statistical analysis of samples from a number of mines from Queensland and New South Wales it can be concluded that there is a direct correlation between the barometer and oxygen concentration at a goafstream sample point. To help mitigate some of the high consequence hazards within the underground coal industry and protect the health and safety of the persons within that environment, many monitoring tools are utilised. A control recognised in management plans prescribed under New South Wales and Queensland legislation is the need to conduct monitoring to identify the early warning signs of spontaneous combustion. One of the monitoring tools utilised involves a bagsample being collected from a goafstream sample point then returned to the surface for analysis.When the sample is incorrectly collected, the resultant analysis from a gas chromatograph provides litt le value to the persons charged with the obligation of operating the coal mine at an acceptable level of risk. This, therefore, increases the probability of spontaneous combustion leading to a loss of equipment, mine and in the worst case, life. When the sample is collected correctly, the analysis presents early warning signs of low level oxidation allowing corrective action to be taken, to prevent the oxidation accelerating to spontaneous combustion. The eff ect the barometer has on this sample point should be recognised and the knowledge imparted to persons who conduct sampling to remove a variable in the bag sample collection process. This will ensure the persons operating the mine have a bett er understanding of what is happening within their longwall goaf."

Jun 1, 2012

By R. W. Barbaro, J. M. Mutrnansky

This paper presents a nonlinear integer goal programming model that optimizes a mineral production schedule while considering the penalties and bonuses based on quality variations in the final product. It involves five coal quality goals plus a profit objective in its formulation and uses the weighting method of goal programming for a solution. The goals to be sought involve the sulfur, ash, heat content, moisture content, and ash softening temperature of the blended coal product. The model is linear in its handling of most of these goals but uses a piecewise linear integer formulation for the sulfur and heat content bonus and penalty schedule. The model is applicable to any mineral product blended from several different sources and subject to a varying price dependent on blended product quality or qualities. However, it seems to be most pertinent to optimizing production schedules for coal deliveries to power plants. Accordingly, the model is applied to a hypothetical coal production problem where multiple coal mines are operated to supply a final blended product to a power plant. In this example, the price paid for the coal is assumed to be a function of five of the most important coal qualities. The problem is solved as a direct function of the coal supply contract, thus removing the necessity of determining the weighting coefficients on a subjective basis.

Jan 1, 1987

By Julian Brown, Steve Hicks, Zach Agioutantis, Zachary Wedding

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By Daniel Soares, Rodrigo Moreira

En un escenario altamente competitivo, la innovación se ha vuelto esencial para la supervivencia sostenible de las organizaciones. Sin embargo, proyectos de esta naturaleza poseen características muy específicas, ya que presentan alto riesgo e incertidumbre en comparación con proyectos convencionales. Desde su concepción, las iniciativas de I&D deben gestionarse de forma diferente. En 2011, Nexa Resources reestructuró su área de Innovación y creó el Directorio de Tecnología, con el foco en la implantación de proyectos de I&D. Se desarrolló una gobernanza específica para la gestión de esos proyectos, donde se definieron y estandarizaron tanto los procesos de gestión como la estrategia de innovación que la empresa seguiría en su planeamiento estratégico.

Sep 20, 2019

By John P. Turner, Mark Jen, Bobby Daita

"The Port Authority of New York and New Jersey is replacing the existing Goethals Bridge built in 1928 which is deemed to be functionally obsolete. The replacement bridge will consist of a dual cable-stayed Main Bridge crossing the Arthur Kill with elevated approach spans connecting Elizabeth, New Jersey and Staten Island, New York. The main bridge towers are supported on a group of six nine-foot diameter drilled shafts that transition into a pier cap. The anchor and approach piers are supported on two column bents with each column supported on a single drilled shaft. The 4.5 to 10 feet diameter drilled shaft foundations have permanent steel casing to rock and socketed into bedrock. Subsurface conditions consist of Passaic Formation bedrock overlain by varying thicknesses of overburden soils. The foundation design assumes permanent casing extending a minimum 2 feet into the weathered bedrock. Rock socket lengths below the permanent casing vary between one to two shaft diameters based on the quality of the bedrock. The reinforcing design was based on AASHTO LRFD minimum requirements, force demands, seismic detailing requirements and also considering the continuity between the shaft and socket.The bridge is currently under construction with approximately 70 percent of the foundations installed. Several field conditions encountered at various stages of shaft construction between casing advancement and concreting required design and construction modifications. Based on the driving method and the quality of the bedrock, the tip of the permanent casing hit refusal either above or below the design elevation, requiring modifications to the drilled shaft design and its reinforcement. This paper provides an overview of the general subsurface conditions at the site and its impact on foundation design and discusses the detailing worked into the design to accommodate tip elevation variations, as well as various foundation design modifications in response to actual conditions encountered during construction."

Jan 1, 2016

By Chunli Wei, Mark Jen, Xiaojun Wang

"After more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges. Each bridge includes 1,650 feet long signature steel composite cable-stayed bridge, a 2,789 feet long New York approach and a 1,889 feet long New Jersey approach. The superstructure of each approach is supported on a series of two-column concrete piers and each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock.A performance-based methodology was followed for the strength and extreme event limit states design of the drilled shaft foundations. The design for seismic loads has been performed using the AASHTO Guide Specifications for LRFD Seismic Bridge Design. For all strength and service loads, the AASHTO LRFD Bridge Design Specifications were used. Since the longitudinal and confinement requirements in the two specifications vary, the minimum longitudinal reinforcement was based on the more stringent requirements of the two codes. A design example is presented to illustrate the methodology in bridge deep foundation design using nonlinear time-history global analysis results with soil-pile interaction represented by sets of horizontal and vertical nonlinear soil springs along the drilled shaft, based on the soil and rock properties from the boreholes test results. In this paper the design methodology implements strain limits related to earthquake intensities and damage levels to calculate the capacity using XTRACT analysis, which aids designers to adopt applicable provisions that meet specific design requirements.INTRODUCTIONAfter more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges designed to carry vehicular traffic and a future mass transit corridor. They include two 1,650 feet long signature steel composite cablestayed bridges with 260 feet tall V-shaped concrete gateway towers (Figure 1). The approaches consist of continuous pre-stressed concrete girders. The New York approach is a single structure consisting of 18 continuous spans, sloping at 4% for a total length of 2,789 feet without expansion joints. Similarly, the longest continuous portion on the New Jersey approach, with a similar slope, consists of 11 spans for a total length of 1,889 feet without expansion joints. The superstructure of each approach is supported on a series of two-column concrete piers that vary in height from 121.3 feet near the cable-stayed bridges to 11.8 feet near the abutments. Each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock."

Jan 1, 2016

By J. Winters, L. Vos, C. Canoo

Committed to a sustainable development of zinc applications, Union Miniere is investigating processes for the minimisation of waste and residues originating from the classic hydrometallurgical zinc process. In that context, Union Miniere has developed a method for the cold inertisation and solidification of goethite, the Graveliet® process. The result is a hard and inert gravel that can be used in the building industry. During the past two years, a pilot plant for the production of Graveliet® has been built and operated. In the present paper, the Graveliet® process and the pilot plant are described after which the properties of the produced gravel are discussed, from both a mechanical and an environmental point-of-view. Graveliet fulfils the criteria for use as a secondary building material. The GravelietJ process is a viable technology to avoid stockpiling of goethite residues and it thus assures the long-term development of the hydrometallurgical zinc process.

Jan 1, 2000

By K Blay, C McCamley, P Petrucci

The Newmont Boddington Gold (NBG) processing plant was designed for 35Mt/y with ball mills expected to deliver a combined new mill feed rate of 4837 tonnes/hr. Since beginning commercial production in late 2009, the plant has steadily increased throughput to meet design capacity in 2014 and reached 37 Mt/y in 2015. Through improved efficiencies, changes to the milling circuit have taken place since commissioning to take the plant beyond its design to an actual throughput of 39.0 Mt in 2017 and a budgeted throughput of 39.4 Mt/y this year.The NBG milling circuit has four parallel ball mills, each consisting of a 7.9 x 13.4 m ball mill with twin 7.5 MW fixed speed motors in closed circuit with twelve 650 mm cyclones. Each mill is fed by two wet screens with the undersize gravitating to a mill discharge hopper where it is combined with the ball mill discharge and pumped to hydrocyclones for classification. The cyclone underflow is re-ground to a target P80 of 150 µm.This paper will focus on process improvements made to the NBG milling circuit which include cyclone reconfiguration, fine screen panel redesign, implementation of an expert control system, mill power draw increase and grinding media changes to take NBG beyond its design throughput.CITATION:McCamley, C, Petrucci, P and Blay, K, 2018. Going beyond design at Newmont Boddington Gold, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 497–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Jake Gibson

"As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action toward decreasing greenhouse gas (GHG) and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel, accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery-powered ac systems and diesel-fired heaters, going noidle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, standalone mobile equipment HVAC.The history of GHGs and climate changeIn 1896, Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960s, Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Fig.1).In 1988, the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgment of a rising global annual temperature. The IPCC consists of more than 2,500 scientific and technical experts from more than 60 countries. Because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998, requiring all participating countries to reduce their GHG emissions by at least 5 percent from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States). In 2002, the Bush administration announced a policy for climate change relying on domestic, voluntary actions to reduce the "greenhouse gas intensity" of the United States economy by 18 percent by 2012. The U.S. still attends the Kyoto conference of parties (COPs) but does not participate in negotiations, as it is not bound by its terms."

Jan 1, 2014

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By Ken Bright

This paper is an overview of approaches to assessment of ore grade for gold and the platinum group at the exploration stage of a project. Proper sampling techhniques must be complemented by good assaying. In turn, correct assaying has its roots in thoughtful, systematic sampling and sample preparation procedures. While intricacies of the subject matter could occupy a book, we will comment on acceptable sampling approaches, outline a lab hand- ling scheme, and discuss preferred analytical methods. Pitfalls previously encountered by the mining and exploration industry will be highlighted with emphasis on a perceptive under- standing of the nature of ore occurrence. Lastly, focus will be centered on reliable assay approaches.

Jan 1, 1988

By N. D. Ilankoon

"The use of thiosulfate as an alternative lixiviant for cyanide to treat complex refractory ores followed by the use of ion exchange resins (IX resins) for gold recovery has become an industrial reality. In this study, polyethylenimine (PEI) coated iron oxide magnetic nanoparticles (MNPs) were used to recover gold from the leaching solutions that consist of calcium thiosulfate, copper and gold. The gold loaded MNPs were easily separated from the solution using an external magnetic field. Proposing a novel adsorbent with characteristically easy solid-liquid separation, to recover gold from synthetic thiosulfate leaching solutions and gold elution and reuse of MNPs were the main objectives of this study. Adsorption isotherm studies revealed that the data fitted both Langmuir and Freundlich isotherm models equally well. The maximum adsorption capacity was 18.5 mg/g at pH 8 and 50?C. According to thermodynamic studies the physisorption process was exothermic and spontaneous. Gold and copper elution, and the regeneration and reuse of the nanoparticles were investigated and promising results were obtained. Different elution systems comprising sulfites, chlorides, glycine, EDTA (ethylenediaminetetraacetic acid) and sodium hydroxide were considered. Among them, EDTA for copper elution and NaOH for gold elution were the most efficient eluants. Regeneration and reuse studies revealed that the MNPs can be used for several cycles without significant performance loss. INTRODUCTION Although cyanidation has been used for gold leaching for more than 100 years, some major drawbacks associated with cyanidation have led to a quest for alternative lixiviants for gold leaching. Cyanide is ineffective in treating carbonaceous refractory ores as gold cyanide complex is adsorbed onto the native carbon in the ore itself known as preg-robbing. On the other hand environmental concerns associated with cyanidation drives the need for environmental friendly alternatives for cyanide. As of today, thiosulfate is known to be the most extensively studied and most promising alternative lixiviant for cyanide in both technical and environmental perspectives (Aylmore and Muir 2001, Oraby 2009)."

Jan 1, 2018

By Michael M. Kimberley

Gold is sufficiently valuable that concentrations as small as 1 p.p.m. may support low-cost mining. Mindful of this, Sunoco Energy Development Company (Sunedco) obtained fire-assay analyses on some sulfide-rich sandstone encountered during routine drilling. Initial fire-assay values from independent laboratories indicated some significant gold values and independent analysis by atomic-absorption spectroscopy also indicated detectable gold at economically interesting concentrations. Sunoco geologists realized the potential for spurious results inherent in both fire assaying and atomic-absorption spectroscopy. Fire assaying that relies on gold measurement by weight requires perfect separation of gold from all other elements, Imperfect separation may artificially enhance apparent gold concentrations. Atomic-absorption-spectroscopy (AAS) measurements are potentially subject to interferences from other elements. For example, Beamish and Van Loon (1977, p.4) report AAS measurements of 4 p.p.m. Au to be characteristic of completely barren soil samples when samples are prepared by standard dissolution in HC1 to form solutions of about 10,000 p.p.m. total cations (mostly Na, Ca, Mg, Al, and Fe) .

Jan 1, 1981

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017