Search Documents

By J. Willison

Over the past decade, the coal mining industry has faced the difficult task of remaining profitable in the midst of declining market prices. Historically, the industry has been quite capable of meeting this challenge by various means. As total costs to mine and market coal continue to increase, new methods of tackling the problem must be implemented. Studies have shown that although many options exist to influence both inby and outby costs, the greatest potential remains in addressing costs at the coal face. Mining operations can positively effect a change in their profitability by either reducing costs, or by increasing production to in turn lower their net cost per man-hour. Original equipment manufacturers can play a key role in both options through the introduction of new technology that permits higher extraction rates, as well as other advantages leading to lower cost coal. A leading advancement over the past 30 – 40 year period has been the advent of progressively higher voltages to operate the mining equipment. This advance enables higher power transmission for a given cable size, operation at lower amperages resulting in less voltage fluctuation, and reduced heat on the cable and electrical components.

Jan 1, 2003

By H. R. Manouchehri, A. Weh

"High voltage electric pulse comminution (SELFRAG) relies on inducing electrical breakdown that occurs when the resistivity of a dielectric is insufficient to completely block all transfer of electricity while the conductivity is not high enough to fully accommodate the flow of electricity without considerable changes to the crystal lattice. The technology is based on introducing the electrical discharges into solids immersed in water and placed between two electrodes. The technology has received significant attention since investigations have revealed the potential for fully fragmenting particles or pre-weakening rocks in order to reduce the energy consumption in comminution practices, improve liberation and potentially increase the recovery in mineral processing. Mineralogical analysis of samples showed possible liberation at coarser sizes by high voltage breakage in comparison with conventional mechanical comminution.This study explored the potential of implementing SELFRAG to treat the Sandvik’s Mittersill mine tungsten ore (scheelite) for recovery improvement. Accordingly, standard SELFRAG tests were conducted on four samples from the tungsten process plant to evaluate the energy-breakage relation and potential to liberate the value minerals at coarser size fraction for recovery improvement. The size reduction of the ore after processing with SELFRAG revealed that size deportment occurs at 0.4, 0.2, and 0.1 mm, which indicated potential liberation of gangue and target minerals at respective sizes. In comparison with conventional milling, the difference is the deportment of values into 0.4 mm sizes, which was, to some extent, confirmed by SEM liberation analysis. However, more tests are needed to proof the concept. The study has indicated that, despite consuming more energy in comparison with conventional mechanical comminution, there are promising prospects in liberating the values at coarser fraction and improve recovery by making use of SELFRAG. The energy consumption can be reduced through customized generator and equipment setup, which must be further investigated."

Jan 1, 2016

By Madgwick J. C

A new strain of Thiobacil/us ferrooxidans (SPK I) has been isolated which has a higher copper to iron release ratio (2.04) than the standard T ferrooxidans (CPBI) (1.12). The diminished iron oxidizing ability enables almost quantitative release of copper (93 per cent) from a chalcopyrite-rich concentrate without interference by iron reprecipitation. In a single batch leach, Bougainville copper concentrate yielded 9.3 grams/litre soluble copper from a 4 per cent w/v suspension in 100 days at 32°C.Solvent extraction recovery of soluble copper is recommended as a final step in a leaching process.

Jan 1, 1983

By C. Caballero, K. Itagaki, P. Morales, A. Moyano, J. Font

Codelco-Chile is considering different processing options for the new projected concentrate from the Alejandro Hales mine. This concentrate is featured by its high arsenic content of up to 6%. Thus, it is important for Codelco Norte Smelter to define the technical feasibility for processing this high-arsenic bearing concentrate in its main smelting unit as it is the Teniente Converter, which beside of its dual feeding system can enhance the arsenic removal by volatilization. The present paper which is a part of an extensive research work will focus in the performed industrial scale test for processing about 7,000 tonnes of a high-arsenic bearing concentrates in the Teniente Converter at the processing rate of about 2,300 tpd. The impact on the chemical quality of the produced high grade matte will be discussed, and the effect of the As removal by increasing the Teniente Converter processing rate of concentrates up to 3,000 tpd when producing 70% Cu in the white metal will also be addressed.

Jan 1, 2007

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk, either at the commissioning of a concentrator or at the point of implementing an improvement to an existing concentrator operation. High-confidence flotation testing (HCFT) was developed for this purpose and is part of the list of technologies at various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of research on this methodology at Xstrata Process Support, Sudbury, several improvements to the HCFT method and complementary connections between sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified. Key words: Flotation testing, Flotation

Jan 1, 2010

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk either at concentrator commissioning, or at the point of implementing an improvement to an existing concentrator operation. High-Confidence Flotation Testing was developed for this purpose, and is part of the list of technologies of various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of practice and continuous improvement with this methodology at Xstrata Process Support, Sudbury, several improvements to this method and complementary connections into sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified.

Jan 1, 2009

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By Richard Cole

The Energy Act of 1992 has many users of ac-induction motors eyeing premium-efficiency motors with mixed feelings and perhaps some confusion. When the October 1997deadline arrives for compliance with the1992 standards, the winners will be the environment due to reduced need for more power generating plants and the petroleum economy because of reduced dependency on foreign oil. But what will it mean for industrial users? The most obvious benefit is the potential for smaller electricity bills. Motors account for about 64% of the electricity consumed in the United States, at a yearly cost of $112 billion. Every 1% reduction in motor demand cuts 0.64%, or $716 million, off the industry wide bill. Higher efficiency motors also run cooler. This lightens the load on air-conditioning systems and further reduces plant demand. Lower total demand can lead to lower rates by helping to minimize peak-demand surcharges. As rates increase over time, these savings get bigger.

Jan 1, 1996

By E. E. Bauer

Oversize boulders in mines and quarries must be broken for waste disposal or further processing of ore. Early methods involved drilling and "shooting" or using a drop ball of sufficient weight to accomplish the purpose. The first "high-energy" hammers for breaking concrete or boulders were pneumatically operated. Blow energy was limited by valving and air pressure. However, smaller boulders of lower compressive strength could be broken. A hydraulic excavator-backhoe type machine was required for either a drop ball or hammer. Standard practice was to break oversize boulders in the pit before hauling to the grizzly or crusher. Generally, quarry boulders were not valuable enough for further processing. Quarry roads were lined with oversize boulders. As safety requirements were advanced, "drill and blast" for boulders was ruled out.

Jan 1, 1994

By Henrique D. G. Turrer, Robert F. Winterfield, Jobe E. Wheeler, Marcello R. Cru, Baojie Zhang, Pedro P. Pinto

Efficient particle classification is essential to enhance gravity and magnetic separation stages in one iron ore beneficiation plant. This study investigates the use of high-frequency screens to process finely ground iron ore, focusing on two size cuts: 400 μm and 100 μm. Pilot-scale trials were performed on four ore blends using a full-scale screening unit. A total of 48 tests were conducted, evaluating the effects of panel aperture, solids concentration, wash water, and feed particle size distribution. Results showed that wash water improved efficiency by up to 5%, while a solids concentration near 40% w/w delivered high separation performance with minimal ultra-fines in oversize streams. Apertures slightly larger than the target cut sizes yielded better precision in particle separation. Feed particle size distribution had limited impact on efficiency. The investigation successfully identified optimal screening conditions, including aperture selection, to achieve the most effective separation performance for downstream concentration processes.

Feb 22, 2026

By C. D. Harrison

This paper presents the results of 18 high-G centrifuge tests performed at the Electric Power Research Institute's Coal Cleaning Test Facility in January 1985. These tests, using -28 mesh (0.6mm) froth flotation product, show that the high-G, solid-bowl centrifuge can produce clean-coal moistures of less than 12 percent at solids recovery rates exceeding 98 percent. The high-G centrifuge achieved these low moistures by applying centrifugal forces up to 2,000 times gravity. Because these forces are two to three times the forces used in a screen-bowl centrifuge, the high-G centrifuge can use a solid bowl and still produce a low-moisture product. The solid bowl captures ultrafines that would pass through a screen bowl, and thus obtains higher recovery rates than a screen-bowl centrifuge.

Jan 1, 1985

By B Morey, J Gordon, P Mackenzie

Mount Tom Price Mine is peerless amongst Rio Tinto iron ore resources around the world. It has provided Hamersley Iron with premium quality, high lump yield haematite ore over the last four decades. The Brockman type bedded ore, containing bands of haematite and shale of varying thicknesses has been traditionally bulk mined to either high-grade or low-grade based on alumina cut-off grades. As open pit mining has progressed deeper into the orebody approaching the keels of the megastructure, increased structural complexity, chemical and physical variations in the ore, unfavourable ore presentation and reduced blending options have become an issue for grade control and may have serious impacts on product stockpiles. The grade blocks and boundaries must be accurately defined according to geological contacts and where identified, selective mining may be applied. Therefore in-pit geological mapping is the definite and ultimate guide to achieve target grades and grade predictions. Under this scenario, it is absolutely vital that the mine geology team ensures this geological knowledge is passed onto the related departments including mining crews as well as to the short- and long-term planners.

Jan 1, 2002

By T Davis

Cameco Corporation operates the high-grade 140 tpd fly-in/fly-out underground McArthur River Uranium Mine in Northern Saskatchewan in a joint venture with Cogema Resources Inc. Reserve grade is in excess of 20 per cent U3O8 with current mining grade averaging 16 per cent U3O8. Due to the high radiation potential of the ore, the non-entry mining method of raiseboring was chosen to minimise worker radiation exposure potential. The raisebore and extraction horizons are located in waste rock with the orebody located between horizons. Ore produced by raiseboring is delivered by LHD to an underground SAG mill and is then hydraulically hoisted to surface receiving facilities after underground thickening to 50 per cent solids by weight. Concrete backfilling is utilised. The orebodies at McArthur River are adjacent to water bearing sandstone. Ground freezing is therefore employed to isolate the ore from this water bearing ground. Calcium chloride brine at -35¦C is circulated through a series of cased boreholes to establish freeze walls up to 25 metres in thickness. At 18 000 000 lb of low cost U3O8 production per annum, McArthur River ranks as the worldsÆ largest uranium mine. Over 50 per cent of the workforce resides in this sparsely populated area of Canada with approximately 40 per cent being of aboriginal ancestry. Site operations must cater for winter temperatures as low as -50¦C.

Jan 1, 2002

By O. E. Palasvirta

Close examination of most so-called new processes in mineral dressing reveals that they were conceived and developed a long time ago. High-intensity magnetic separation is no exception. Although its application in iron ore beneficiation seems new, in Germany the process has been commercially successful for almost two decades. High-intensity separators have long been standard equipment in the glass sand industry; they have also been used in concentrating some of the more unusual paramagnetic minerals. The basic features of an induced-rotor, high-intensity magnetic separator were described by Désiré Korda in Paris in 1905,1 and many patents have since been issued for improvements on the original design. Fig. 1 shows the basic design of an induced-rotor separator. Several U. S. manufacturers have been supplying induced-rotor separators for many years, but these are all devices of relatively low capacity, not suitable for treating such low-cost commodities as iron ore. On the other hand, two German manufacturers are offering induced-rotor separators of high capacity, both proven in the field.

Jan 12, 1959

By E. Yan, M. Mankosa, G. Luttrell

"During the past decade, column flotation cells have become widely accepted for upgrading ultrafine sulfide ores. However, the use of columns has been widely relegated to cleaner circuits due to their comparatively high selectivity derived from the use of wash water dispersed over a deep froth. High tonnage rates and low feed grades make using column technology in roughing and scavenger stages challenging due to the resulting size of the needed equipment. To specifically address this challenge, a new high-intensity flotation system known as the StackCell™ was developed. This technology makes use of a novel pre-aeration method coupled with froth washing to simultaneously provide improved flotation kinetics and selectivity. The novel aeration system provides efficient bubble-particle contacting thereby shortening the residence time required for particle collection. This article reviews the technical design features of this new flotation technology and presents recent data from in-plant pilot testing in a copper-sulfide application. INTRODUCTION Column flotation cells have become very popular in the minerals processing industry for cleaner circuits due to their ability to produce a high-grade froth concentrate via the use of froth washing (Luttrell et al., 1999; Kohmuench et al., 2004). The use of wash water minimizes the nonselective recovery of ultrafine impurities that are normally entrained into the froth product from conventional flotation machines. On the other hand, the unique design of a column cell typically requires a large tank volume. Column cells must be tall to ensure that the pulp residence time is long enough to offset their inherently slow flotation kinetics and to minimize internal mixing that is detrimental to overall cell performance. The tall design minimizes the total floor space required for the column installation, but substantially increases the foundation load. The large size of the column tank can also create issues during fabrication, transportation and installation. To address these concerns, the engineering team at Eriez Manufacturing developed a next-generation flotation technology called the StackCell?. This high-intensity flotation machine was designed to provide column-like separation performance within a very compact volumetric footprint. This article describes the key working features of this new technology and provides data from recent pilot-scale tests conducted in gold and copper-sulfide applications"

Jan 1, 2016

By B. Wasmund, M. Parravani, M. Jastrzebski, Z. Coull

"One of the main drivers of overall profitability of pyrometallurgical vessels is refractory lining campaign life. Increased economic pressure to improve vessel life requires innovative solutions to the problem of refractory cooling. Hatch has recently developed a high-intensity, waterless cooling system that bridges the performance gap between external shell cooling and internal water-cooled copper elements. External shell cooling has a limited effectiveness in protecting the refractory lining, because it is thermally insulated from the hotface of the lining by its thickness. This situation does not improve until the lining itself has become worn near the end of the campaign. The patented technology developed by Hatch overcomes this problem by positioning high-velocity air-cooling channels within the lining, closer to the hotface where the cooling benefits can be realized throughout the entire duration of the campaign. The current paper presents the development and application of Internal Air Cooling technology as well as results from the pilot campaign in an operating commercial vessel. Various adaptations for this novel, cost-effective and inherently safe system are also discussed."

Jan 1, 2015

By Diego L. Romero, Joy P. Romero

"IntroductionMinerals may be classed broadly as ferromagnetic (magnetite for example), as paramagnetic (attracts to regions of magnetic field convergence) and as diamagnetic (attracts to regions of magnetic field divergence). High-intensity separators are not necessary to separate ferromagnetic minerals from other classes. Rather, low-intensity units that generate fields below 5000 gauss are adequate for this purpose. However, paramagnetic minerals, such as ilmenite, with high magnetic ""attractability"" require fields of up to 10 000 gauss; those with low attractability may require even higher fields. Table 1 shows approximate ranges of field intensities necessary to separate ferromagnetic and paramagnetic minerals from minerals of lower attractability, along with the force with which they are attracted relative to iron in a standardized magnetic field.Uniform magnetic fields, not useful for separators, are generated between flat parallel surfaces; non-uniform fields, useful for separators, arise when at least one of the surfaces is of irregular shape. The diagrams below show how magnetic lines of force align relative to north and south poles.If a particle is placed in a uniform field, it feels no displacing force unless the particle distorts the applied field assymmetrically. This is not the case in non-uniform fields which are required for magnetic separators.Magnetic fields can be generated by permanent magnets (low intensity), by electromagnets (medium and high intensity) and even by superconducting coils (100 000 gauss fields and higher), although the latter are not as yet useful in production environments .The magnetic force of attraction per unit of mass, that acts on a paramagnetic mineral such as hematite, increases in proportion to the strength of the field . Unfortunately, the highest fields attainable with electromagnets is of the order of 20 000 gauss. Fortunately, the gradient of the fie ld (that is, the degree of convergence of magnetic lines of force) is important, because the attractive force per unit mass is proportional to it also . This can be stated:"

Jan 1, 1989

By Takayoshi Fujii, Mitsumasa Hoshi, Chikashi Suenaga, Yoshiaki Suzuki

"In a bid to renovate its Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, Nippon Mining & Metals undertook major - restructuring efforts since 1993.One of its themes was the shift from a two-flash furnaces operation to a single-flash furnace operation. The shift was successfully completed in 1996 while maintaining the production at the same level (330,000 metric tons per year of copper) by adopting such measures as improvements in pneumatic concentrate dryers, the concentrate feeding system, concentrate burners, the furnace cooling system, and a new cryogenic oxygen plant was constructed.With a view to realizing high matte grade operation (at 65%Cu) and increasing the concentrate feeding rate, further steps were taken the capacity of waste heat boiler was expanded and technical improvements were added, including optimization of the smelting reaction in the furnace shaft. As a result, the smelting capacity, as of the year 2000, has increased to 450,000 metric tons per year of copper.IntroductionThe feed rate to the flash furnace was doubled to 140 t/h from 70 t/h in 1996. Teething problems, as a result of the renovation, were almost solved by the end of 1996, and the operation of the single furnace operation has become stable.The main theme was the shift from a two-flash furnaces operation to a single-furnace operation to maintain the production capacity at the same level, namely 330,000 metric tons of copper per year. Then, in a bid to further renovate the Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, further enhancement of the flash furnace's productivity was planned.The purpose of this plan was to raise the copper production capacity to 450,000 mtpy building on the potentialities of existing plants and without installing new equipment."

Jan 1, 2000

By Yuanfei Chen, Jianfeng Zha

"China is the largest producer and consumer of coal in the world. The mining-induced surface subsidence has bad influences on the surface and structures above the surface. In order to minimize disasters, removal, reinforcement, or maintenance structures are often adopted. In the application of maintenance methods, it is necessary to carry out dynamic surface subsidence prediction to choose maintenance methods, optimize maintenance time, and evaluate the amounts of work. Time series methods and influence function methods are common for dynamic surface subsidence prediction, but the former is difficult to consider with underground mining conditions, and the latter has low prediction precision. Therefore, this paper develops a dynamic subsidence prediction model aided by field-measured data and realizes the model programming. The model could achieve high-precision prediction of dynamic surface deformation through optimizing the parameters in time by using field-measured data of surface subsidence. The research results of engineering cases show that, with the method of dynamic prediction, the standard error can be controlled in the range of 5%, greatly improving the accuracy of dynamic prediction of mining subsidence, which provides strong technical support for the maintenance and management of structures. INTRODUCTION With the rapid economic development and continued industrialization process, the demand for energy is growing in China. Today, China is one of the largest coal, oil, and gas consumers in the world. Coal consumption accounts for 47.7% of the total consumption in the world (Tian, 2016). In order to meet the demand for coal resources in the process of modernization, more and more coal mines carry out coal mining under villages, buildings, highways, and bodies of water. The mining-induced overlying strata and surface subsidence have bad effects on surface and on various structures (such as buildings, railways, highways, high-tension transmission lines) and could even cause various disasters (Williams et al., 1998; Bell et al., 2000; Doyle et al., 2002). Generally, methods, such as removal, reinforcement, or maintenance are taken to eliminate the adverse impacts (Kraatz, 1984; Bell and Genske, 2001; Wang, 1989). When reinforcement or maintenance is selected to remove bad effects, the proper maintenance methods must be chosen. In addition, maintenance time, as well as an evaluation of time it will take to do the work are necessary to predict the surface subsidence with high precision."

Jan 1, 2017