Search Documents

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By I. Cameron, S. Ramjee, A. M. Garbers-Craig

The cause of reduced workability and increased ageing of a blast furnace taphole clay was examined. The investigated taphole clay contained 60 mass% alumina, with phenol-formaldehyde resole resin and liquid pitch serving as the binder system. The workability and Marshall extrusion pressure of the as-manufactured clay samples were evaluated to assess the extent of ageing of the clay. The wettability of all the raw materials was investigated to confirm compatibility between the dry raw materials and both the resin and liquid pitch, while the dry raw materials were analysed using XRF, XRD, and SEM-EDS. The characterisation of the resin and liquid pitch, as well as an analysis of their interaction, was performed using viscosity measurements, Fouriertransform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The analyses confirmed a chemical interaction between the resole resin and liquid pitch, where the chemical structure of the resole resin changed when mixed with pitch, preventing the typical curing behaviour of the resin. Upon ageing of the resin-pitch mixtures, the resin underwent premature cross-linking, causing the curing process to initiate at lower temperatures, i.e., earlier onset of curing. This premature cross-linking was likely due to secondary amines present in the liquid pitch, which acted as a catalyst for the curing process of the resin. This reduction in curing temperature after ageing was confirmed by an increase in binder viscosity, which was identified as the primary cause of reduced workability, accelerated ageing, and increased Marshall extrusion pressure of the taphole clay.

Jul 23, 2025

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

Over 800 mines have closed in Australia in the past 25 years. This paper summarizes the data obtained from those closures and includes all Australian States and Territories and all commodities, including metalliferous, coal and industrial minerals. Twenty five percent of the mines closed due to resource exhaustion or depletion; 24% due to high costs, price drops, or declining grades; 8% due to open pit resource depletion (but with underground reserves remaining) or underground reserves depleted (but plans to open cut remainder) and 7% due to receivership or voluntary administration. The environmental, social and economic impacts of these closures are also significant and include acid mine drainage and impact on mine employees. An understanding of the causes of premature mine closure will better equip mining companies and governments to better manage future mine closures, wherever in the world the mines are operating.

Jan 1, 2007

By Bruce Hebblewhite

An ACARP-funded industry research project in Australia recently investigated the problem of premature rock bolt failures in underground coal mines. The project carried out limited sampling from 9 different collieries in NSW and Queensland, followed by a more comprehensive, controlled sampling from one colliery. Over 50 broken bolts were collected and subjected to metallurgical analysis at UNSW to determine both the steel composition and to analyse the fracture surfaces. Prior to this study, there had been anecdotal evidence of similar bolt failures from a number of sites within the industry. The sampling and analysis conducted by this project - whilst being below a statistically representative sample of the entire industry bolt population - highlighted the fact that bolt failures were continuing to occur at a number of sites, in both older and recently installed bolts. The failures were almost entirely attributable to stress corrosion cracking (SCC). It appears that a combination of factors - including steel composition, bolt manufacturing process, loading environment, geological and hydrological environment, bacterial corrosion - can all contribute to this problem. There is no simple solution, however, as with similar research findings from the UK, it appears that steels with higher values of fracture toughness, or Charpy Index, are less susceptible to SCC. Testing to date has been limited to bolt failures below the resin encapsulation horizon. A real concern is the potential extent of the problem at higher horizons, within the encapsulation. These may require some form of non-destructive testing (NDT) for detection. Initial trials in Australia of the ultrasonic device developed by DMT in Germany have proved encouraging. Further testing using this device is anticipated in future research. This paper describes the outcomes of the project, completed in 2002.

Jan 1, 2003

By E. G. Langille

"The Premier mine; owned by Silbak Premier Mines; Limited; is 14 miles from Stewart at the head of Portland canal. Development of the property began in 1918; and since chat time a very large amount of gold and silver as well as some lead and copper have been produced from the mine.The area in the vicinity of the mine is underlain by greenstones tuffs, and sediments of Mesozoic age, belonging to the Bear River formation of the Hazelton group. These rocks are intruded by a stock 2 miles in diameter, composed of orthoclase porphyry and called the Premier porphyry. It sends numerous sill-like and dyke-like tongues into the Bear River formation, and is intruded in turn by a granodiorite outlier of the Coast Range batholith. The orebodies occupy fractures and fracture or shear zones. Primary ore consists chiefly of pyrite, galena, and sphalerite, with some chalcopyrite. The upper 300 feet, or locally 600 feet, contained presumably secondary silver minerals."

Jan 1, 1954

By J. A. Voster

Premier Mine (a part of De Beers Consolidated Mines Ltd) which is situated 38 km to the east of Pretoria, has the largest known diamond pipe in South Africa. The mine started operations in1903. The Premier Mine kimberlite pipe is unique in that it is intersected by a 75 m thick gabbro sill at a depth of 400 m below surface. The current mining method used is mechanized panel retreat caving, which has been successfully used to extract ore from the different mining blocks. All caving at Premier Mine is below the sill and failure to exercise good draw control could cause the early ingress of gabbro waste. Draw control at Premier Mine is crucial as it aids in preventing conditions of isolated draw, which results in the early ingress of waste, compaction of the kimberlite and the loss of ore reserves. To assist, an underground vehicle monitoring and control (VMAC) system was installed to enable the effective management of the draw control function. The system has evolved graduallyin collaboration with a local developer. The data accumulated is used to decide the most effectivedraw point loading pattern in order to achieve sound draw control principles. This is achieved as each load can be related back to the draw point of origin. The VMAC data recorded also relates back to specific load-haul-dumps (LHDs), tunnels, ore passes, as well as indications of dates, times and payloads recorded. An interface exists between the VMAC and a draw control linear program. Premier Mine’s VMAC system is not a ‘dispatch’ system but rather a draw control system that caters for Premier Mine’s specific block cave requirements. Premier Mine has realized that successful automation is not dependent on technology alone but rather on the successful implementation thereof.

Sep 1, 2001

The most appropriate technology needs to be applied to premining geological investigations to achieve reliable data for predictions of geological conditions ahead of mining. The paper describes the application of various investigatory techniques in BHP's Illawarra Collieries which are used to provide reliable assessments of structure, the nature of the coal and surrounding strata,, and the fluids contained in the strata. The techniques used include surface seismic, in-seam seismic, borehole drilling, electromagnetic and aeromagnetic surveys, hydrogeological investigations and in-mine mapping. The results of various case studies are presented as examples of the application of techniques.

Jan 1, 1988

By Yoginder P. Chugh, M. Silverman

Premining investigations involve the determination of roof, floor, and coal seam characteristics to delineate areas of troublesome ground control prior to development of a mine. Data obtained can be useful in mine design, equipment selection, estimation of face productivity, development of ground control plans and assessing ground control costs, and in conducting feasibility studies and financial analyses. This paper discusses 1) the causative factors associated with ground instability, 2) how useful data can be obtained for these factors during premining investigations, and 3) analysis techniques to delineate probable areas of ground instability.

Jan 1, 1982

By R. D. Caudle, Yoginder P. Chugh, V. K. Agarwala

Longwall coal mining is a growing mining technique in the United States. However, very little premining exploration data are collected presently by coal companies to 1) select coal winning equipment, 2) select and design face supports and supports in gate and tail entries, or 3) optimize operational parameters such as length, width, and orientation of face. The authors are of the opinion that much of the data needed for mine planning and design for longwall mining can be obtained during exploration. In this paper, the authors identify the data requirements, discuss how these data can be obtained during exploration, propose an exploration program and estimate the cost to obtain the necessary data.

Jan 1, 1982

By Ronald D. Hill, Elmore C. Grim

Mining as an extractive process alone is outdated and unacceptable to today's environmentally concerned public. Multiple land use must be considered as well. Only through effective preplanning can the full potential of reclamation result in a lasting asset for future generations. The coal industry is now recognizing that reclamation of mined lands is part of the mining cycle that must be planned and carried out in a timely and orderly manner. It is also finding that planning reclamation in advance of mining is cheaper and more effective than waiting until mining is completed. The decision to open a strip mine must be based on the results of studies to determine if successful reclamation can be achieved and whether the economic benefits to the company will be justified(1). Information regarding the physical, chemical, hydrologic and biologic systems operative at the site must be under- stood or reclamation will be a failure. Working together, engineers, management and reclamation specialists should design the actual mining and reclamation plan before mining is begun.

Jan 1, 1974

By J. C. Johnson

High-grade ore found in a shaft pillar at the Homestake Mine prompted a request for a Bureau of Mines study to determine if selected areas of the shaft pillar could be mined without jeopardizing the shaft. The design approach was to perform a finite-element study of the shaft pillar. Plan view and vertical sections were developed using two-dimensional, elastic, plane strain assumptions. Input into the model consisted of in situ stress measurements geologic mapping rock mass properties, and previous mining history. Results from the study indicated that ore-beating sections of the shaft pillar could be removed within the displacement tolerances acceptable for the shaft. Homestake engineers, using the results of the finite-element study and considering other factors, have designed and are beginning to mine the shaft pillar.

Jan 1, 1989

By Dan White

Stress measurements taken at Climax, El Teniente, Henderson, Lakeshore and Urad mines indicate that the deposits cited are generally subject to an inclined stress field that can be highly anisotropic. The horizontal stresses vary significantly between deposits and exceed the measured vertical stresses at Henderson and El Teniente mines. Experience at Henderson, Lakeshore and Urad mines is used to suggest a relationship between cavability and the premining stress. In poorly fractured, high strength rock masses, high stresses can assist the caving process. In well fractured, low strength rock masses, caving is ensured by breakage along fracture planes. The relationship between ground weight and the premining stress is also investigated. Ground weight problems appear to be most related to the competence of the ground rather than the magnitude of the premining stress as supported by experience at Climax and El Teniente mines. Recent developments in block caving favor the extraction of poorly fractured, high stressed rock. Accompanying the development of these deposits are new problems such as rock bursts. These pose particular problems to mine designers in that no experience currently exists in combatting rock burst problems at block caving mines.

Jan 1, 1984

By William F. Eichfeld, Robert J. Wenzel

INTRODUCTION The phrase "subsidence control planning" can refer to the use of specific mining methods and-specialized techniques to control subsidence events or it can refer to planning for subsidence by predicting its magnitude and timing and further planning mitigation strategies. In the first case the objective is actually subsidence prevention while in the second it is a design procedure that seeks to maximize the use of both surface and subsurface resources. Neither technology is well developed at this point. The purpose of this presentation is to briefly outline the Department of Energy's Subsidence Program. This program is, in general, bases on the premise that subsidence control technology, by any definition, can be accomplished only through a thorough and rigorous understanding of subsidence phenomena. This understanding must come from many well planned and executed studies of stress redistribution and strata deformation as they occur during mining activities. There is presently considerable incentive to improve our subsidence engineering capabilities due to the desire for increased coal utilization with acceptable environmental impact. Considerable research in this area is being sponsored by federal and state governmental agencies, universities, and the coal industry. Federal sponsorship has been borne by the Department of Energy, the Bureau of Mines, the Office of Surface Mining and the U.S. Geological Survey for the most part. These agencies have carried out basic research in their laboratories and have contracted with other organizations for additional work. At this time most of the available resources are directed toward contract research, especially in DOE. It is the DOE research plan which will be addressed here.

Jan 1, 1982

By R. Q. Honaker, D. Tao, D. Taulbee, B. K. Parekh

A significant amount of energy exists in the waste generated by the coal and timber industries. In the coal industry, the energy loss is mainly due to the discharge of fine coal to the waste impoundment. Despite the fact that the fine coal has the greatest cleaning potential, dewatering, handling and transportation concerns prevent its use as product in many cases. Likewise, the sawdust generated from wood production has energy value and is used as industrial boiler fuel when the transportation distance is relative short. However, wood waste is often discarded into cumbersome landfills due to uneconomical transportation alternatives. Recent research found that these two waste materials can be combined to provide a high energy fuel of around 13000 btu/lb that can be easily handled and transported to end users.

Jan 1, 2004

By S. S. Churchill

Introduction Amidst the apparent chaos of the final push to complete a major construction project, a small group of specialists works with great intensity. Armed with yellow "in test" and green "turned over to operations" tags, these startup engineers follow detailed preoperational test procedures to confirm that a plant is ready to operate. They follow a test schedule designed to complete individual process system in the order they will be needed by operations. After extensive preliminary testing, the startup engineers begin the truly exciting part of their work - initial operations. The thrill of engaging the clutch for the first time on a 10,000 horsepower grinding mill makes all the long hours worthwhile. Preoperational testing and startup are of critical importance to the success of a project. No other aspect of a construction project allows such opportunities for success or failure, and no other aspect is so critically influenced by careful planning. At Bechtel, the tasks of preoperational testing and startup are among the responsibilities of the Mine and Plant Operations group. The Preoperational Testing Process Preoperational testing is the transition phase between constructon and startup on a new plant. It includes the preparation of detailed test schedules and procedures. The schedules are used to coordinate construction completion activities, so that systems are available for startup and operations in a rational sequence. The procedures form the basis for performing the testing and documenting its completion. Tests include instrument calibration, wire insulation tests, wire termination verification, mechanical alignments and inspections, and system cleaning and flushing. Where possible, the systems are then operated on water and their performance recorded. Normally, either the construction contractor or a team of specialists has the responsibility to perform preoperational testing. Witnesses to the testing may be owner operations and maintenance personnel, engineers from the design firm, or specialists assigned to the project who provide assistance and guidance to the contractor in addition to witnesing the work.

Jan 1, 1986

Consolidation Coal Co. is solving the abrasion problem and cutting maintenance costs at its Georgetown preparation plant by using ceramic alumina tiles from The Carborundum Co. The Georgetown complex handles the output of four deep mines and three strip mines in the Cadiz, Ohio, area-washing about 73 000 tons (80,000 st) weekly. Plant superintendent Duke Zinko is using wear-resistant Dura-frax® tiles in several applications, replacing wear plates, profile rubber, and other materials he has tried over the years.

Jan 7, 1979

By R. P. Smith

PRIOR to June, 1937, the employees of Hollinger Consolidated Gold Mines, Ltd., at Timmins, Ontario, received medical care for themselves under a contract system developed through an agreement between the employer, employee, and a contract physician. This form of practice is common to the mining industry in Ontario. But with the improvement in mining methods and conditions of living, and through an increasing demand for provision of a complete medical care, it was not any surprise when the employees of the Hollinger mine approached organized medicine and indicated their desire for a plan to provide their families with a more or less complete medical service in addition to that supplied for themselves. In April, 1937, this approach was made, and on June 18th, 1937, the Hollinger Employees' Medical Services Association was formed and started to provide medical services. A review of five years' experience is now presented. The Association provides complete medical service for the employee, his wife and family, as well as those dependents who are the total responsibility of the employee. The employee membership is limited to employees at the Hollinger mine in Timmins who reside in the immediate vicinity. The employee is examined by a Company doctor on application for employment and is subject to further examination by a specialise in chest diseases under the direction of the Workmen's Compensation Board of Ontario. The wife and family are not subject to examination but have to be registered when the employee is accepted for employment. The dependents, other than the immediate family, are subject to medical examination and approval after the employee has applied for such dependent or dependents to be admitted. Membership in the Association is obligatory when the employee is hired, but at the end of any Association year he may drop out if he so wishes.

Jan 1, 1943

By J. Bese.

El presente texto señala un método de solución para el establecimiento de una mina. Este método se aplica a través del análisis de factores de los principales gastos; el costo del transporte en las principales galerías de exploración y los procesos directos de producción. Asimismo, se estudia las inversiones, los requerimientos de mano de obra en conexión con la producción y los factores de gastos de producción observando el efecto de los parámetros tecnológicos sobre los factores diversos de gastos.

May 1, 1975

By Thomas Fraser

"El siguiente estudio señala las recomendaciones para la preparación de las antracitas del Santa de la mina ""La Limeña"", así como las modalidades para determinar los efectos de la ""trituración"" diferencial y ""maceración"" en agua del carbón del tipo ""Limeña"". El resultado de estas pruebas en Bradford, mostraron que el carbón de ""La Limeña"" es adaptable para la ""trituración"" diferencial. Dicho mineral es mucho más blando que el relave, de allí que una gran proporción del carbón limpio disponible permanezca en su tamaño lógico inferior a 5/16"" producido en la extracción y manipuleo. Así también el tratamiento experimental de los tamaños mayores en una planta del tipo Bradford se divide en dos: el primero refiere un relave ""duro "" de tamaño mayor, que contiene una pequeña cantidad de carbón limpio, brillante y fácilmenteescogido a mano; y lo segundo, es una mezcla de tamaño inferior, de ""middling"" y carbón para lavado posterior."

Jul 20, 1955