Search Documents

By Wendell H. Nielson

Flotation processes contain disturbances which make material balance closures difficult to achieve. Lack of closure also arises from instrument errors. A portion of these problems can be overcome by proper equipment selection; the primary measurement installation and methods of initial data filtering are discussed below. The problem of data adjustment has been considered before (2). The technique described here is essentially that of Ripps (2). The technique was expanded to include linearization of non-linear material balance equations. An additional large error detection portion was also added to Ripp's formulation. Ripp's technique is based on a Lagrange-Multiplier optimization method. The Lagrange-Multiplier technique is generally applied when there are equality constraints on the variables. Steady-state material balance equations fit in this category. The basic Lagrange-Multiplier method is described. It is followed by a description of the modified material balance data adjustment technique. An example is presented to illustrate the use of this method.

Jan 1, 1970

By William Petruk

An investigation was conducted to determine whether mineral liberation data obtained by one image analysis technique are the same as data obtained by another image analysis technique. The liberated vs non-liberated, volume % and weight % techniques for measuring mineral liberations by image analysis were tested. The results show significant differences between the values obtained by the different techniques. The lowest liberation values were obtained by the liberated vs non-liberated technique and highest by the weight % technique. It is interpreted that the weight % technique produces the most realistic results. The weight % technique also produces data that can define mineral associations for the unliberated grains. These include (1) mineral quantities in particles that contain different amounts of unliberated mineral, (2) mineral quantities in particles that have different size ranges, and (3) mineral quantities and degrees of liberation for specific minerals in particles of different size ranges.

Jan 1, 1996

By C. Groccia

As the search for new ore bodies drives mines to be developed at greater depths, the associated high stress environments present challenges for rock support design. Excavations in highly stressed brittle rock are often subject to large volume increases due to rock failure, a phenomenon known as rock mass bulking, which can result in significant wall convergence. Support systems need to be designed to minimize the amount of bulking and to accommodate large wall convergences. In order to design such a support system, empirical guidelines are often used to predict the amount of bulking. However, the empirical guidelines that are currently available are based on a limited number of case studies and consider few input parameters, which may result in an inaccurate bulking assessment. This paper describes methods of collecting quantitative field data at Creighton mine in Canada to better understand rock mass bulking and to further develop the empirical guidelines for bulking assessment for tunnels in highly stressed grounds. Measuring

Aug 1, 2013

By Jon C. Yingling

Techniques for optimization of mineral processing flowsheets are reviewed. Though not yet widely used in the minerals industry, approaches for chemical process optimization based on successive quadratic programming (SQP) algorithms may be employed to determine optimum unit design and control settings for a mineral processing flowsheet. Moreover, in certain mineral processing flowsheet applications, specialized techniques can be applied because of the nature of the system relations. These techniques offer advanta es in efficiency. Moreover, their capability exceeds that o f the SQP approaches since simultaneous optimization of circuit configuration and unit controls can be addressed.

Jan 1, 1990

By Partridge AC

The measurement of particle size is very important in many industries. Comments in this paper refer principally to the Mineral Industry and in particular to Coal Mining and Coal Preparation. The objective is to indicate the importance of particle size in process design and process assessment and to describe techniques for particle size measurement and the presentation of results.

Jan 1, 1984

By Garfield Schnee

MACHINERY has not taken the place of manual labor in steep pitch coal in the anthracite field and there is a shortage of miners experienced in this type of work. To overcome these difficulties several coal companies have resorted to different types of mining such as the diamond or zig-zag method, the slant method, long hole drilling, and several other variations. For the past 5 years the diamond shape method has been used extensively in the heavy pitching beds of both the Knickerbocker and Yatesville basins at Knickerbocker colliery of the Philadelphia & Reading Coal & Iron Co.

Jan 10, 1950

Blast performance is related to rock structure and strength, as well as to factors such as site geometry, drill patterns, explosives loading, firing sequences and delays.

Jan 1, 1986

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT Data frequently can be collected by several dif¬ferent methods. The method required for the nec¬essary precision for inflow prediction to mines should be selected and other methods avoided. Pre¬cision monitoring or measuring techniques fre¬quently require more time, expertise, and expense in their implementation that may not be justifiable. The temporal distribution of the data needs also may dictate the method used for data collection. Continuous recording devices may be required for time sensitive data whereas point measurements of other parameters may be adequate. Data needs will vary as the hydrologic investigation proceeds. In¬itial data needs may require only a qualitative col¬lection of data such as the areal distribution of precipitation. Subsequent data needs may require the measurement of ground water levels to the near¬est hundredth of a foot. Data requirements can be difficult to fulfill for ground water systems. This is particularly true for anisotropic, heterogeneous hydrostratigraphic units since the hydrogeologic parameters vary both ver¬tically and areally. Techniques exist for determining the storage characteristics of both unconfined and confined hydrostratigraphic units but these pro¬cedures require the installation of multiple wells in the same unit which may be impractical. Specific tests are discussed subsequently that permit the determination of vertical hydraulic conductivity. Data collected from field procedures or tests are generally preferred to laboratory derived data. This is especially true for hydrogeologic parameters such as hydraulic conductivity. SURFACE WATER SYSTEMS Precipitation Precipitation data can be collected from sources that maintain a historical record. The US Depart¬ment of Commerce, National Oceanic and Atmos¬pheric Administration (NOAA), maintains weather observation stations across the country. Such a sta¬tion frequently can be found near a proposed mine site but the type of weather data collected varies from station to station. Fortunately, precipitation data are collected ubiquitously. The data collected by NOAA can be purchased for the area of interest in the form of monthly and annual tabulations. Private weather stations constitute a second source of precipitation data. Existing data usually are analyzed by one of three methods. The station average method merely sums the depth of precipitation at each station and divides the sum by the number of stations as fol¬lows: [ ] where Pavg is the average precipitation (L), P, is the depth of precipitation at station i (L), and N is the total number of stations. This method is applicable where there are a relatively large number of stations uniformly distributed across the area (Hjelnfelt and Cassidy, 1975, pp. 71-72). The second method, called the Thiessen poly¬gon method, weights the precipitation at each sta¬tion in direct proportion to the area it represents without consideration of topography. The stations are plotted on a map and perpendicular bisectors are drawn on the lines connecting the stations. The polygons formed by these bisectors constitute the area that the precipitation for that station repre¬sents. The overall precipitation can be calculated with the following equation:

Jan 1, 1986

By Yong-ping Wu

Based on the rules of strata behavior and the characteristics of rock movement, the elementary problems of using fully mechanized coal mining techniques in steeply dipping coal seams are described. A model of the "surrounding-support-rock" relationship is made. The support systems stability during fully mechanized mining of steeply dipping coal seams is studied. Then, a practical engineering example of the fully mechanized mining of a steeply dipping seam is presented. The seam used in the example is in the Lushuidong colliery, which is administrated by Huaying Mining Bureau, Sichuan Province.

Jan 1, 2003

"Mining with blast holes drilled upwards may be done to recover sill pillars, or for economic reasons when the distance between the levels is relatively large. If the rock is sufficiently competent to accommodate large stope size, the distance between sublevels could be increased to as much as drilling accuracy allows. The same drill drift can be used for the drilling of both down holes and up holes. In the case of down holes, the initial opening of the stope (drop raise) is not as much a problem as for the inverse drop raise for mining with up holes. This is because, with a drop raise, a lot of space is available at the toe for the blasted rock to expand. In addition, the raise can be blasted in many shots, thus allowing smaller blasts each time. Inverse drop raises are generally much more difficult to blast because of the limited space for muck flow, and must, therefore, be taken down in a single blast, requiring special considerations in order to ensure a success. A case study of a 29 m (95 ft) inverse drop raise successfully blasted in a single shot at Heath Steele Mines is described. The paper covers technical considerations such as drilling accuracy, hole deviation survey, delay extension and protection, initiation methods and initiation sequence. Finally, a novel method for creating the initial opening called ’slot drilling’ is presented. This method, inspired from LKAB in Sweden, consists of drilling a row of interconnected holes using a special guide mounted on a regular production drill hammer.With a case study of blasting an inverse drop raise of 29 m (95 ft) in one blast, this paper further discusses some technical issues that are critical for the development of inverse drop raises. A novel method for creating the initial opening with a slot of interconnected holes is also presented with the experience acquired at different mine sites across the Noranda group."

Jan 1, 2000

By Howland Bancroft, Louis S. Cates

WE have come a long way since the order of the day was the chance discovery of mineral deposits, breaking rock with fire and water, melting metals in open fires in holes in the ground or in primitive furnaces, digging pits to collect. oil seepages, burning eroded coal outcrops to develop heat, and so on. During the past 5500 years, gradual improvements in methods and equipment have come about, explosives have been developed and used, steel has been used in increasing quantities and effectiveness as its physical and chemical characteristics, and composition have been altered and made to serve specific ends, hand equipment has given way to almost completely mechanized operation Thus, by the aid of mechanical equipment, one person is now able to move several thousand times as much material as one person was able to move a relatively few years ago. When this Institute was formed 75 years ago, the Suez Canal had been open to traffic but three years. It had taken ten years to complete and was built under the direction of French engineers by workers of whom many were girls. During the first four years of construction, these workers dug up the sand with their fingers, threw it into rush baskets, carried the load a hundred feet or so and dumped it 2 (With the termination of forced labor, dredgers completed the digging of the channel.) At the present time there is in use in the United

Jan 1, 1947

By George Young Mosteller

This paper is summary of the practical solutions developed in the excavation of drilled piers (caissons) at GPCo's Plant Scherer, Juliette, GA. Plant Scherer is a 3,245 Megawatt Fossil Fuel Powerhouse and, when completed, will be one of the largest fossil fuel plants in the Southeast.

Jan 1, 1980

By Mohan Dutt

This paper is concerned with applied platinum resistance thermometry which involves many considerations absent in precision thermometry. The historical development of the Callendar-Van Dusen Equation which describes the resistance- temperature relation of pure platinum is discussed. The advantage of using platinum resistance temperature sensors over thermocouples is described, and the improvements in design and construction of these sensors that have come about in the past few years are discussed. Integral and remote bridges that convert resistance changes into voltage together with signal conditioning techniques and equipment for voltage or current signals are described. Errors encountered in temperature measuring schemes and methods to reduce these errors are summarized.

Jan 1, 1969

By Robert Hivick, Frank Sames

The control of environmental effects, especially blast vibration and airblast, has become a dominating planning criterion for most surface blasting operations. Compliance with existing regulations is generally achieved through constraints in the blast design, or monitoring programs. Commonly, blast vibration and airblast signals are rated and compared by their maximum amplitude and the associated principal frequency. However, this data reduction limits the interpretation of the influence of varying blast design parameters on the vibration and airblast.

Jan 1, 1999

By Dennis R. Dolinar

The U.S. Bureau of Mines has modeled yield pillars to determine the effects of reinforcement techniques on pillar performance. Model pillars with width-to-height (w/h) ratios ranging from one to four were reinforced using advanced lateral support systems. To evaluate reinforcement and pillar performance, the model pillars were strained up to 18.6 pct in compression. The results show that the reinforcement had a significant effect on the postfailure characteristics of the pillar but had only a small effect on it's maximum failure strength. Pillar residual strengths increased up to 10 times, while the energy capacity increased by a factor of three depending on the reinforcement method. At maximum deformation, the residual strengths of several types of reinforced specimens exceeded the maximum compressive strength up to 2.5 times and resulted in an increasing positive postfailure stiffness. Test results, data analysis, and application of the results to underground mining are discussed.

Jan 1, 1993

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories a

Jan 1, 2009

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories and other ground control subjects and broad experience are required.

Jan 1, 2009

By S. F. Diehl

Suites of monomineralic sulfide and carbonate minerals, as well as mine-waste composite samples, were analyzed using chemical and microanalytical techniques to understand behavior and bioavailability of mine waste elements such as Cu, Fe, Pb, or Zn. Petrographic, scanning electron microscopy (SEM), and laser-ablation inductively-coupled mass spectrometry (LA-ICP-MS) studies of mineralogical residence sites of trace elements are important because trace elements affect the chemical and physical behavior of minerals. Leachate solutions show that chalcopyrite, bornite, azurite, malachite, and galena are host to the trace elements Ag, Al, As, Cd, Co, Cr, Mn, Ni, Pb, and Zn. SEM studies reveal whether these trace elements occur within mineral inclusions or are substituted within lattice structures. SEM analysis reveals mineral phases not identified by X-ray diffraction (XRD), such as inclusions of sphalerite and cobaltite(?) within chalcopyrite.

Jan 1, 2010

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

The system of keeping geological plans and sections for the Geco Mine at Manitouwadge, Ontario, is described. Special methods employed to save draughting time with-out sacrificing accuracy, such as the extensive use of black line prints, are discussed. The uses made of the plans and sections by the mine planning engineers in their designs of stopes, and by the blast-hole engineer in ~is preparation of blast-hole layouts, are noted. An unusual scheme for portraying the distribution of .copper, zinc and silver values within the ore zone is de-scribed. The method of estimating the grade of ore to be "blasted in each ring of blast holes is outlined, as is the method of estimating the annual ore reserves. The design of an effective but simple transparent geo-logical and mine development model, used as a display for -visitors, is discussed. A large-scale model used for the study of problems in geological structure is also de-scribed.

Jan 1, 1964