Search Documents

By Ghislain Bournival, Seher Ata, Graeme J. Jameson

A common method to prevent bubbles from coalescing in a flotation cell is by the addition of surfactants, called frothers. The gas dispersion properties in a column were tested for solutions of 1-pentanol, tri(propylene glycol) methyl ether, and poly(propylene glycol) in the presence of sodium chloride. The dependency of surfactant on the gas holdup can be divided into regions. It seemed that for a sufficiently low concentration of surfactant, even a stronger surfactant could show a transition in gas holdup from constant/decreasing to increasing with concentration. This region, however, was not marked by a decrease in the average bubble size. In addition, PPG gave higher gas holdup values while averaging larger bubbles. On the other hand, sodium chloride mostly affected the gas holdup when the concentration was high enough to prevent bubble coalescence. Another parameter affecting the gas holdup was the superficial gas velocity. A linear dependency was found between the two under a bubbly flow regime. The current study showed that both surfactants and salt could slightly affect the influence of the superficial gas velocity on the gas holdup.

Jan 1, 2014

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study is to compare amino acids and organic acids in the extraction of gold from silicate ore. Amino acids were found to have higher efficiency of gold extraction than organic acids at the same acid concentration, which is likely due to amino acids having both carboxylic and amine groups in their structure, while organic acids only have carboxylic groups. Five amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and seven organic acids (citric, malic, tataric, fumaric, oxalic, succinic and ascorbic acids) were selected to investigate gold extraction efficiency. Aspartic acid was found to have greater capacity to extract gold than succinic acid. The optimal gold to aspartic acid molar ratio was 1:6, and low concentrations of aspartic acid extracted 35 to 42 percent of gold from silicate ore within 15 days. Further studies are needed to increase gold leaching and reduce incubation time. The results imply that aspartic acid can be used as an alternative reagent to traditional methods for extracting gold from ore. This method is nontoxic to humans, is environmentally friendly and can have real applications.

By I. M. R. Duarte, J. A. Rodrigues-Carvalho, F. R. S. Rosa, A. B. Pinho

"This paper aims to contribute to the knowledge of the mechanical properties of the shales and greywackes which constitute the flysch-type deposits of the Baixo Alentejo Flysch Group, in the south of Portugal. These formations are flysch-type deposits constituted by sequences of usually thick greywacke beds alternating with thin shale beds, which include sometimes intercalations of conglomerate beds. All the sedimentation of these flysch formations was controlled by tectonics. At the same time, should have occurred along with the first Hercynian deformation phase, a low-grade metamorphic event (chlorite zone), that affected these flysch deposits. This study highlights the influence of anisotropy and heterogeneity of these flysch rocks on their physical and mechanical characteristics. The anisotropy verified in some physical properties and on mechanical properties, due to the foliation makes difficult the sample preparation for the laboratory tests. Besides, it induces a scattering of the properties values measured, as for example, the strength and the deformability. The heterogeneity is related to the main features of these geological formations, which are constituted mostly by thinly stratified greywackes and shale beds, which sometimes may affect the results of the laboratory tests making them less representative. The study is made by using both shales and greywackes that constitute these flysch-type deposits in order to evaluate their geotechnical properties, mainly of the shales. Samples of these two rock materials, are tested accordingly a laboratory testing programme, which includes which included mineralogical analysis (X-ray diffraction), physical tests (bulk density, porosity, and void index) and mechanical tests (uniaxial compression, and deformability tests). INTRODUCTIONOne of the factors that most influence the geomechanical behavior of rocks, as well as rock masses is the anisotropy. The word anisotropy comes from two Greek words ""anisos"" (meaning uneven) and ""tropos"" (meaning direction). A body or material is considered to be anisotropic, where the same property has different values depending in which direction it is measured, therefore, an anisotropic material is one whose magnitude of the properties depends on the direction in which these are studied or measured. Otherwise, it is about an isotropic material. However, the fully isotropic materials are quite rare in nature."

Jan 1, 2015

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By Lijuan Li, Xin Xia, Junjun Huang, Qijie Zhai, Xiang Jiang

"Some experiments with different temperatures (1173, 1223, and l273K) and different annealing times (3, 4, 5, 6min) were carried out on cold-rolled plate of Fe-36Ni invar alloy. The microstructure and the mechanical properties were observed and tested respectively, and the fracture morphology was observed by SEM. The results show that with increasing of the temperature and the annealing time, the austenite grains gradually grow up accompanied by a small amount of annealing twin crystals, meanwhile, its plasticity and toughness are improved, and it is typical ductile fracture under the condition of tensile failure. After annealed at l223K, the invar alloy has better comprehensive properties than that at the other annealing temperatures, and the grains size is more uniform. Furthermore, when the annealing time is 4min, the invar alloy has the best comprehensive properties.IntroductionAs we known, most metals and alloys expand with increasing temperature. More than one hundred years ago (in 1897), Guillaume observed that Fe-Ni alloy with face-centered cubic (fcc) crystal structure, consisting of36%Ni, showing a very small thermal expansion coefficient below the ferro-to-paramagnetic transition, the thermal expansion coefficient around room temperature( <2 X 1O-6K-1 compared to most metallic materials which have a thermal expansion coefficient of 10-20 X 1O-6K-1) [1,2]. Since then, the subject has attracted many researchers, and various alloys with low thermal expansion coefficients have been developed. These alloys, generally known as ""invar alloys"", are in demand where dimensional changes due to variation in temperature must be minimized and where high stability is required [3, 4]."

Jan 1, 2012

By F. Chiesa

Forty aluminium A356 castings were poured on a Low Pressure Permanent Mould industrial machine, 500x700mm in platen size. The 152mm wide casting comprised three steps, 25mm, 13mm, 6mm in thickness and a 2.5mm overflow which allowed to assess the thin wall capability of the process. The casting campaign, which produced 40 parts, allowed to test the influence of various production parameters including the time of application of the pressure in the crucible, artificial cooling of the mould and casting rate. The thermal history in the mould was recorded over the 40 cycles, which allowed to construct a reliable thermal model of the mould/casting assembly. The metallurgical quality of castings representative of the various conditions was assessed in the 25mm, 13mm and 6mm plates. This included measuring the level of microporosity, the dendrite fineness (DAS), along with the tensile properties in the T6 condition. The radiographic quality per ASTM E155 was also determined. Modelling filling and solidification allowed to verify the validity of the predictions based on available relationships relating microporosity, secondary dendrite arm spacing (DAS) and local tensile properties (Quality Index, Q) to the local thermal solidification parameters.

Jan 1, 2007

By Gao K, Wu C, Langley J. M, Waugh B, Farrell K

The dissolution of carbon from carbonaceous materials into molten iron is a key step in various ironmaking operations. For example, in new direct smelting processes, carbon in the form of coal is injected into the molten iron bath, which leads to the dissolution of carbon. In foundry operations, typical recarburizer materials can range from high purity graphite to chars. The dissolution performance of these&quot; materials is critical to the operation and could dictate the efficiency and economics of the process.Dissolution kinetics has been studied by various investigators to explain the influence of melt conditions and carbon type (Sahajwalla et al, 1994; Shigeno, Tokuda, and Ohtani, 1985; Orsten and Oeters; 1988; Ganguly and Reid, 1992; Wright and Taylor, 1993). The influence of melt sulphur content on the dissolution kinetics has been characterised (Sahajwalla et al, 1994), with sulphur retarding the rate of carbon dissolution. The carbon dissolution from different sources is seen to vary significantly even under similar melt conditions. This observation has been explained by investigators on the basis of the varying ash content present in the carbonaceous materials. However, ash content alone cannot account for the variability in dissolution kinetics reported in other studies. One such study is presented below.In a recent study (Sahajwalla et al, 1994), pulverised carbonaceous materials were injected into the molten iron bath and the&quot; dissolution kinetics was established. The dissolution of graphite and glassy carbon, which contain almost 100 per cent carbon, was seen to be significantly different when the molten iron contained sulphur. The influence of melt sulphur content was explained on the basis of different wetting behaviour observed.Importantly, the study showed that even pure carbon sources dissolved at significantly different rates. Hence, their performance could not be explained on the basis of ash content.The key difference between graphite and glassy carbon is in their atomic structure. Graphite is highly ordered whereas glassy carbon has relatively poor ordering in its atomic structure. This study showed that the atomic structure in carbonaceous materials can have a significant effect on their dissolution performance.The focus of the present investigation which stems from the past study described above (Sahajwalla et al, 1994), is to investigate the influence of atomic structure of carbonaceous materials on their dissolution into Fe-C-S melts.The specific objective of this study is to determine the relationship between dissolution kinetics and crystallographic character of carbon sources. In order to accomplish this goal, a range of different materials representing a spectrum of carbon sources have been chosen for the investigation. These materials include brown coal char, two types of Auscarb (A and B), and commercial graphite. Auscarb is prepared by calcining Auscoal at 1000&#176;C. Auscoal is made from chemically cleaned Australian coals (Bowling, Chandler and Waugh, 1990). Part 1 of this paper details the dissolution performance of the materials studied, while Part 11 describes the X-ray diffraction study. The relationship between the atomic structural dimension and dissolution rate constant is discussed in light of the results obtained.

Jan 1, 1996

By R. J. Hafsten, E. S. Davenport, R. A. Grange

THE influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,1 and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely retarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar&apos;) when the austenite grains are increased in size. More recently, Griffiths, Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745°F. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245°F. (675°C.), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarse-grained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite-that is, at temperature levels above about 1000°F. (540°C.)-but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to be presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000°F. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. MATERIAL AND EXPERIMENTAL PROCEDURE The material investigated was a commercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent M0. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By Vikram P. Mehrotra

A laboratory investigation was carried out to study the influence of asphalt, bentonite and corn starch binders on the pelletization kinetics of coal fines and on the quality of the resulting pellets. Pellet quality was evaluated in terns of the compression strength, impact resistance (drop test), abrasion resistance and resistance to severe weather conditions. The amount of binder addition did not significantly influence the pellet growth kinetics. However, the pellet quality varied markedly depending upon the type and the amount of binder used. Experimental results are explained on the basis of the mechanism of interaction between the coal particles and the binders. Of the three binders tested, corn starch proved to be the best in all respects but for the resistance to water penetration. Finally, a combination of corn starch (imparting strength) and asphalt emulsion (imparting resistance to water penetration) was found to yield the best quality coal pellets.

Jan 1, 1981

By P Moser, P Schimek, F Ouchterlony

This paper summarises the findings of 27 model-scale bench blasts in magnetic mortar, which were conducted from 2011 to 2014 at the blasting site of the Montanuniversitaet Leoben.The aim of the study was the investigation of the influence of blasthole delay times in small-scale bench blasts on the face characteristics and cracking damage created in the surrounding rock, which affects the fragmentation in subsequent rows.The test specimens or blocks, which were produced out of magnetite concrete, were roughly 1:100 in scale to normal bench blasts. The confinement of the testing blocks at the sides and back ensured the similarity to normal bench blasts with regard to the wave transmission into the surrounding rock. The specimen contained three or four rows with five blastholes each and were shot row by row, with virgin (undamaged) material in row 1 and increasingly damaged or preconditioned material in the following rows.The tested delay times varied between 0, 28, 73 and 140 &#181;s, which corresponds to 0, 0.4, 1.0 and 2.0 ms/m of burden.The evaluation of the material properties showed that the use of magnetite concrete eliminated the inhomogeneous behaviour of rock, but some unexpected differences of the individual production cycles were still detected.The characteristics of the bench after each blast was evaluated along three horizontal lines out of a 3D model of the bench face. The tested delay time sequences of the virgin (first row) and single preconditioned blasts (second row) produced more overbreak for longer delays, while the third-row shots resulted in a smoothened surface independent of the chosen delay.The introduced damage after every blast was evaluated by an observation of irregularities on the newly blasted bench face. The visible cracks at the top of the testing blocks were documented and divided into several crack families according to their angle, length and origin. The remaining block was broken out of the blasting site after blasting, cut into several horizontal and vertical slices and dye penetrant spray was used to visualise the cracks created. Some of the detected crack families showed an influence of the delay time. The calculated mean crack density and mean crack intersection density showed that longer delays resulted in a higher degree of damage.The fragmentation results were well reproduced by the basic three-parameter Swebrec function. The observed improvement of fragmentation in the second- and third-row blasts was linked to the preconditioning of the burden for the following row while blasting the actual row. With the exception of the simultaneously initiated blastholes, the blasts showed coarser fragmentation for the shortest delays, while the longest delays generated the finest fragmentation.CITATION:Schimek, P, Ouchterlony, F and Moser, P, 2015. Influence of blasthole delay times on fragmentation as well as characteristics of and blast damage behind a remaining bench face through model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T. Marin, J. E. Seccatore, M. Cardu

The most energy-intensive process in the mining industry is particle size reduction – comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq’s halfspace size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.

Aug 8, 2024

By R. K. Singhal

In open pit mining every effort is made to maintain as steep a pit slope as possible. Pi t slope angles are influenced by numerous factors some natural that are amenable to limited or no control at all and other mining technology related where a greater degree of influence can be exerted by the engineer. One such area where control is possible is the method of drilling and blasting in the pit. This paper discusses the influence of blasting techniques on the economics of pit slopes and demonstrates how balanced blasting can be used with advantage to pit wall control and improve fragmentation (thus reducing material handling costs). Microprocessor based instrumentation to monitor drill and blast performance has also been described.

Jan 1, 1988

By Gordon M. Matheson, David K. Miller

Sinkhole development in karst terrains is a serious problem and risk to facilities built in these areas. The potential for sinkholes are a function of many things including the chemistry of the underlying rock, the location of water conductive fractures and fissures in the rock, the natural fluctuation of the ground water table, vibrations from various sources and surface regrading activities. When sinkhole open near quarry operations the occurrence of these features is occasionally attributed to vibrations from quarry blasting. The purpose of this paper is to review the evidence regarding the development of sinkholes as a result of quarry blasting. In general, it has been found that sinkholes result from collapse or piping of overburden soils into cavities or caverns developed within underlying carbonate rocks that have been in existence for many thousands of years. The overburden soils in karst areas are typically clayey and as a result are not subject to densification or liquefaction as a result of vibrations. The primary cause of an increased rate of sinkhole development can be attributed to changes in the ground water table or local surface water drainage. These changes may be caused by seasonal fluctuations, ground water level lowering in drought periods, dewatering of excavations or quarries, or local changes in surface drainage resulting from grading activities.

Jan 1, 1998

By L. Dorador

"In block caving projects, the rock mass fragmentation process plays a controlling role in the design and success of the operation. Poorly understood, however, is the secondary fragmentation that occurs as blocks of caved ore move through the draw column and interact with one another. The initial size of these blocks can be considerable, as can their strength and stiffness as the presence of non-persistent joints and veining will be variable. Intuitively, more planes of weakness within the blocks should facilitate early fragmentation, but this assumption could depend on additional factors such as contact type between adjacent blocks and loads imposed through varying heights of the draw column. This paper reports the findings from a laboratory investigation examining the role of block strength and planes of weakness on secondary fragmentation. Testing was carried out on small-scale concrete cubes of uniform size, with and without embedded planes of weakness. The results obtained demonstrate the significance of veining and other planes of weakness on secondary fragmentation under one-dimensional compression, and allow for the development and constraint of empirical guidelines.INTRODUCTIONThe fragmentation process during block caving involves the initial (primary) fragmentation of rock in the cave back through stress-induced fracturing, release and fall of individual blocks onto the broken ore muck pile. This is followed by secondary fragmentation involving splitting and rounding of blocks as they move downwards through the draw column towards the draw point. The degree of secondary fragmentation achieved involves many variables related to the mechanical properties of the rock blocks as well as different operational factors. With respect to the block properties, the presence of planes of weakness in the form of veining and non-persistent joints is a topic of special interest given the significant influence it potentially has on the overall fragmentation process. However, the inherent heterogeneity and variable size of individual blocks generated from the cave back makes it difficult to develop any empirical relationships relating secondary fragmentation to compressive loading based on insitu observations and mine data. More preferable would be to keep constant block parameters, such as shape (aspect ratio and angularity) and size, through controlled laboratory testing. This work presents an efficient technique to fabricate concrete cubes in order to keep constant different block properties. These are then tested under one-dimensional compressive loading. The objective of these tests is to emulate a tight packing condition of single blocks such as that which would occur when the air gap between the cave back and broken ore in the draw column is small. When the air gap is small, detached blocks are unable to fall and rotate but instead maintain a very tidy arrangement with minimal voids left between adjacent blocks."

Jan 1, 2015

By Claudio Gutiérrez

The action of quebracho in the selective flotation of fluorite and calcite has been studied. It has been found that the unavoidable ions produced by dissolution of these minerals can precipitate calcium oleate which profoundly influences the adsorption of oleate. The depressing action of quebracho is due, at least partly, to a decrease of the oleate adsorption. The depression of flourite flotation by quebracho in the presence of calcium is due to the fact that precipitated calcium oleate can become only physisorbed, its adsorption being strongly prevented by quebracho. It is concluded that adsorption experiments with flourite must be conducted with a flotation-size mineral, which has a lower dissolution rate than when finely ground.

Jan 1, 1980

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

Adding CaO into the vanadium extraction converter is an effective way to decrease the dephosphorization burden in subsequent steelmaking process. The crystallisation process of spinel is one of the most decisive factors in the subsequent extraction. The theoretical calculation results show that the temperature of the peak total crystallization rate will decrease 5K with basicity increasing 0.1. The relation between cooling conditions and grain size of spinels is also discussed. It is found that low cooling rate and high basicity benefit spinel crystal growth. And the non-isothermal crystallization kinetics results indicated that the restriction factors of spinel growth is that solid crystals accept new components from liquid-solid interfacial. While the sample was cooled down to 1250 (1523K) at cooling rate of 5K/min, the crystal growth is consistent with Ostwald coarsening grew up law, and controlled by diffusion of particle.

Jan 1, 2016