Search Documents

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By S. Kirkpatrick, J. Mukendwa

"The mining operation at Namdeb’s Southern Coastal Mine (SCM) is unique. It targets gravel layers up to 30 m below sea level, which continue to dip deeper, further west, under the Atlantic Ocean. On this storm-dominated coastline, severe water seepage into mining areas, rugged orebody footwall characteristics, and highly variable resource grades all contribute to a challenging operational environment. Namdeb has a proud history of innovation, and as the mine progresses further westwards and associated technical and economic challenges increase, this innovative culture has become essential to the future of the mine. The Theory of Constraints (ToC) has been widely used at SCM, and across the mining discipline, to focus efforts on improving overall business profitability. Through analysis of the mining processes, opportunities were identified, solutions developed, and initiatives implemented with staggering results across all three mining disciplines, i.e. stripping, load and haul, and bedrock bulking and cleaning. This paper outlines the solutions adopted and the results of the ToC analysis. IntroductionSouthern Coastal Mine (SCM) is one of three Namdeb operations located in the southwestern corner of Namibia, between the Orange River in the south, the Namib Desert to the east and the Atlantic Ocean to the west (Figure 1). These three geographical features set the backdrop for the world’s greatest marine diamond mining placer (Badenhorst, 2003). SCM is situated along the coastline extending from the mouth of the Orange River to Chameis Bay approximately 120 km to the north. The active mining area, called Mining Area 1 (MA1) is, however, limited to very narrow strip, 30 km in length, in the south of the licence area, close to the town of Oranjemund.Namdeb, a wholly owned subsidiary of Namdeb Holdings, is a 50/50 joint venture between De Beers and the Government of Namibia. Diamonds were first discovered along the Namibian coastline in April 1908, close to the town of Luderitz, but mining operations started in the SCM mining area only in February 1929 (Schneider, 2009). Initially all Namdeb mining operations exploited massive land-based deposits, producing nearly 40 million carats from MA1 between 1920 and 1977 (Schneider, 2009) when mining targeted onshore raised beaches west of the high water line. Since 1977 however, SCM and Namdeb have developed a unique mining method to economically extract the resource which extends westward under the Atlantic Ocean."

Feb 1, 2019

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By Frank Cook

As in other areas of the country, surface coal mine productivity in the Central Coal Province--primarily Illinois, Indiana, and west Kentucky--has declined steadily since 1969 (figure 1). Productivity, as measured in tons of clean coal produced per man-shift, dropped 35 percent during the period 1969-1975. Unwelcome at any time, this phenomenon is particularly untimely now, when increased coal production is a national goal. The U.S. Bureau of Mines has been working with the coal industry to develop new operating methods and equipment to enable increased productivity and improved reclamation performance in surface coal mining. Several projects have involved identification and evaluation of existing overburden handling and reclamation practices, and development of means to improve operational procedures. Some results of one of those projects, as they apply to the Central Coal Province, are summarized in this paper.

Jan 1, 1977

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By J Rutter, J du Plessis, er, M Scott, D Alex

It is generally acknowledged that bulk ore sorting is an attractive prospect for the mining industry. However, uncertainties relating to the operational performance of sensor technologies, the grade heterogeneity present in analysed material and the physical separation performance of the coupled system complicate the evaluation and deployment of bulk ore sorting strategies at operations. To assist in the quantification of these uncertainties, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and Anglo American have implemented a systematic methodology to evaluate the deployment of sensor technologies for bulk ore sorting. This methodology was implemented at a bulk ore sorting demonstration plant using penetrative prompt gamma neutron activation analysis (PGNAA) and surface x-ray fluorescence (XRF) measurements of base metals, as a proxy for precious metals, at Mogalakwena PGE Mine. The methodology comprises of three phases. The initial phase involves the preliminary investigation of sensor technologies and analysis to reduce identified risks prior to commissioning of the bulk ore sorting plant. The second phase executes a series of experiments to prove the sensing technologies in the operational environment and provide confidence the sensors can drive separation. The final phase demonstrates the production scale bulk ore sorting performance of the plant and validates its performance by campaign of the sorted products at the processing plant. Throughout the operational deployment and evaluation of bulk ore sorting at Mogalakwena, several key lessons were learned. These learnings relate to the calibration requirements of the sensor technologies, the application of surface vs penetrative sensor techniques and the preservation of grade heterogeneity delivered to the sensors. This paper presents the methodology used, and lessons learned, in the operational deployment and evaluation of PGNAA and XRF sensors for bulk ore sorting at Mogalakwena PGE Mine.

Nov 10, 2020

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By Bao Xiancheng

Jinlong's copper flash smelting process started up in April 1997. In the early days of production, lots of equipment and process problems were encountered. But, through continuous improvements in equipment and operation, the designed productivity was reached two years later and the smelting operation has been greatly upgraded since then. After more than 4 yew of production, we have made great achievements, such as increasing the flash furnace availability, significant improvements in operation control, optimization of concentrate burner's structure and operation, and smooth operation of the whole smelter. This paper outlines Jinlong's operational achievements made after commissioning, and discusses problems that were encountered and their countermeasures. Operational experience is also summarized

Jan 1, 2002

By A. Longval, Q. Jiao, T. Shannon

In 2000, Xstrata Zinc (former Falconbridge Ltd.) Brunswick Smelter commissioned a modified lead blast furnace. Since then, efforts have been made to improve its operation in order to achieve optimal operation in terms of coke consumption, lead loss to slag, and improved environmental and hygiene conditions. This paper will review the important step changes in operational philosophy, undertaken since 2004, for the control of the blast rate, oxygen enrichment in blast, slag chemistry and charge level. Furthermore, a review of the improvements made in secondary materials consumed at the blast furnace will be made. This paper will also discuss the significant reduction of the frequency of accretion removal as a result of improved furnace operation.

Jan 1, 2008

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate. The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refming times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using C02 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate, The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refining times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using CO2 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance is reviewed.

Jan 1, 1999

By ZáWang, F Hungerford, T Ren

Operations in an underground drill site have to co-exist within the mineÆs ventilation and operational system. The space requirements of a drilling operation have to be adapted to the limitations provided in available site space, which is usually defined by standard mining operations and geotechnical influences. These limitations affect borehole design, equipment positioning in the site layout and possible interactions with mining equipment and services such as water and power supply.The ventilation requirements for drill sites and the means employed vary with depth of the site, space and likely presence of gas. All drilling operations provide a particular service for the mine and in each case, drilling must operate in a manner which controls all gas, water and cuttings returning from the borehole. The various standpiping systems employed have evolved under differing influences and must cater for conditions during and after the drilling operations.The influences that gas content, pressure and flow, rib stability, cleat direction, borehole length, potential water pressure and flow have on a mineÆs operation and ventilation systems have to be considered in the design of standpipe length, diameter and fittings. Past history has a strong influence on common practice while worst case effects of a possible in-hole event should be catered for.This paper describes the early drilling systems and their limitations in ventilation and gas management. The drill site dimensions and set-up are discussed in the context of roadway conditions, equipment layout, ventilation and logistics. The use of standpiping to control all returns from the borehole is illustrated by referring to likely scenarios in a drilling site to achieve the most effective sealed depth to accommodate the worst case possibility of intersecting high pressure gas or water during the drilling operation. Practices to allow gas drainage in the return airway of a panel are described.CITATION:Hungerford, F, Ren, T and Wang, Z, 2013. operational management of underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference , pp 43-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Rahul Bhaduri

Mercury levels in Twin Creeks Vista pit ore (previously Chimney Creek, North pit ore) increased substantially since plant start-up in November 1987. Consequently, modifications were necessary to minimize industrial hygiene hazards and potential operational problems. The original plant design included mercury control measures. With progressive increases in mercury levels, the issue had to be re-addressed. Modifications to operational practice, industrial hygiene and management philosophy will be discussed. Additionally, a detailed examination of the mercury vapor suppression system currently employed at Twin Creeks will be presented.

Jan 1, 1994

By C. Mattich, A. L. Beyzavi

The Waelz Plant at Taiwan Steel Union Co. Ltd. (TSU) was erected within nine months from September 1, 1998 to May 15, 1999. The nominal capacity of the plant is 50,000 tonnes per year of electric are furnace dust (EAFD). The plant, consisting of material handling, a waelz kiln, a waste gas cleaning system, waelz oxide leaching and waste water treatment, was commissioned within three months from July 1, 1999 until October 12, 1999. The specific problem of the plant is the high chlorine content in the EAFD pellets which is up to 6 %. Lurgi Metallurgie GmbH, Frankfurt, Germany was responsible for the engineering erection and commissioning of the plant.

Jan 1, 2000

By B. Cousins

Copper, nickel, zinc and other ?penalty? metals are found with gold together in nature, and have a similar chemical affinity for cyanide used in leaching operations4. As a result, solutions that come from the heap leach pads contain a significant concentration of penalty metals along with the desired gold. In solution, gold and cyanide form the complex Au(CN)2- that is readily adsorbed onto activated carbon. Penalty metals as individual metal ions also load onto activated carbon and, depending on the concentration of cyanide and the pH of the solution, can form various cyanide complexes. Some of these complexes can also load onto carbon while some are significantly inhibited from loading. Copper, for example, can form the dicyanide complex Cu(CN)2-, the tricyanide complex Cu(CN)32-, and the tetracyanide complex Cu(CN)43-. At a low pH and a low concentration of cyanide, the dicyanide complex predominates. At a higher pH and a higher concentration of cyanide, the tetracyanide complex predominates. Without excess cyanide, however, individual copper ions can remain present. Activated carbon is used in gold extraction because it is highly selective for gold and less so for other metals, such as copper3. However, copper has the ability to adsorb (?load?) onto activated carbon and block the adsorption of gold when it is in the dicyanide form and in a high enough concentration. When copper is in the tetracyanide form, copper loading is significantly inhibited, allowing for the maximum gold recovery. In order to ensure the tetracyanide complex is formed, a combination of both available cyanide and elevated pH must be present. In the South Area of Newmont Mining Corporation?s Gold Quarry mine in Carlin, Nevada, copper and nickel loading becomes a problem when certain acid generating zones of the heap are leached. Copper, nickel, zinc and other penalty metals become leachable and the lower pH uses up more of the cyanide and creates carbon loading conditions for the metals. This decreases the carbon?s ability to extract the gold from solution, decreasing the recovery and increasing the concentration of gold in the barren solution that leaves the carbon columns. In this study, operational data from March through to May of 2007 is presented to show how Newmont developed a quick fix to lower pH and elevated metal concentrations that were causing low gold loadings on activated carbon at their South Area Leach (SAL) heap leach operations. Laboratory tested were also conducted to examine the chemical kinetics of metal loading and the individual effects of increased cyanide concentrations. THEORY Copper I ions form four different complexes with cyanide in solution: the monocyanide species CuCN, the dicyanide species Cu(CN)2-, the tricyanide species Cu(CN)32-, and the tetracyanide species Cu(CN)43-. The species are formed from the following reactions: [Cu)(?+-+ K1 (1) Cu ß2 (2) --+?+23)(3CNCuCNCu ß3 (3) --+?+34)(4CNCuCNCu ß4 (4) ] where K1 equals 1019.50, ß2 equals 1024.03, ß3 equals 1028.65, and ß4 equals 1030.35. Along with these complexing reactions, hydrogen cyanide and water also dissociate in solution, as per the following reactions: [H?+-+ KH (5) OHOHH2?+-+ KW (6)] where KH has a value of 109.24 and KW has a 1014 value2. These six chemical equations compete with each other, with domination of one over the others dependent on the CN- and H+ concentrations. Each complex also has different properties when it comes to its loading behavior on activated carbon. The dicyanide copper complex and the monocyanide copper complex have an affinity for adsorption onto activated carbon that is greater than the affinity of gold cyanide for adsorption. They also have a lower solubility in water, which enhances adsorption. The tricyanide copper complex and the tetracyanide copper complex are water soluble and have an affinity for loading adsorption on activated carbon that is less than the affinity of gold cyanide for loading adsorption1. There are three prime reasons for this phenomenon. First, the extra cyanides mask the metal ion more, which blocks the main adsorption characteristic of the complex. Second, the complexes are also larger, making it harder to physically fit into the active sites on the carbon. This helps make the latter two complexes kinetically inhibited from adsorption, freeing carbon active site to load with gold cyanide complexes. Third, it is also important to consider the expressions of the mass and charge balance. These balances describe all the overall concentration of copper and cyanide in solution, as well as marking overall charges of the ions in solution4. This is important because significantly changing the charge from positive/neutral to more negative is another reason for activated carbon to reject adsorbing the higher cyanide complexes. The speciation of copper and other penalty metal cyanide complexes in solution is dependent on the pH. At lower pH values, increased hydrogen ions (H+) can out-compete metals for cyanide ions. Lower free cyanide in the system leads to the lower cyanide species of copper cyanide predominating, with a noticeable concentration of the free metal, monocyanide and dicyanide species of copper cyanide. At higher pH values, hydrogen ions are significantly reduced, reducing the kinetics of HCN formation. More free cyanide remains in the system, allowing for more complexing. With this higher amount of cyanide in the system, the tetracyanide species of copper cyanide predominates, also with a noticeable concentration of the tricyanide species of copper cyanide. Higher copper concentrations, however, require more

Jan 1, 2009

By A G. L Pratt

Operational readiness is a commonly used term in mining and many other industry settings. However, translating this term into a coherent scope of work that is practical and meaningful is a challenge faced by many mining projects. This inhibits the allocation of resources to the work and its completion. The problem is with understanding how the terminology applies to establishing a mining operation. Resolving this problem requires clarity around what operational readiness means for a mining project’s transition to operations and who owns the tasks of completing operational readiness. The motivation for resolution of this problem is in appreciating the consequences arising from any lack of clarity in definition of this task, the timing of the work, and ownership for its completion. In broad terms, these consequences amount to an erosion of value at a critical time for both the new mine and the company and shareholders. This situation often arises where operational readiness is not adequately addressed in project’s study phases. As a result, neither time, resources nor money are adequately provided to complete the work required. In other cases, operational readiness is sometimes assimilated with the delivery of the project’s physical assets by the project’s construction team, rather than aligned with the establishment of the operating team to deliver the desired operational outputs. This paper argues that operational readiness starts in a project’s study phases and flows through into the start of operations. The definition of operational readiness is discussed as a task, and a model for its planning and completion is presented. This discussion includes assigning ownership for operational readiness planning and delivery to the General Manager of a new operation and the operations leadership team, who are central to the success of this work. After all, the reputations of this leadership team depend on the performance of the operation in its first few years. The author’s work over the last 20 years, leading operational readiness programs and the preparation of feasibility studies for mining projects, has provided the insights and evolution of ideas that are central to this paper. Operational readiness is fundamentally directed at ensuring a new mining operation gets away to a successful start and builds a solid foundation for the future of the mine/operation/province. It requires clarity of purpose, ownership and coordination by people in the operating team, and their preparation of the requisite process definition and establishment of the significant relationships required for operations. Without its successful completion, it is unlikely the new operation will meet and sustain its start-up targets. This paper discusses a practical approach to operational readiness for mining projects.

Mar 29, 2023

By Peter Willbrandt

The flash smelter at NA was commissioned in March 1972 with an initial throughput of 50 tons of dry copper concentrate per hour. As a result of various measures, for example, oxygen enriched process wind, extension of the radiation part of the waste heat boiler, etc., the throughput could be increased to the present 70 tons per hour of dry concentrate. NA's plant is located on the outskirts of the city of Hamburg. The flash smelter's location and the growing awareness of the German population as regards environmental issues necessitate again and again considerable capital expenditure being spent on environmental protection. Thanks to the numerous small and large measures taken to protect the environment the emissions of dust, heavy metals such as arsenic, copper, lead, etc., and as well SO, could be drastically reduced. This paper will be giving an overview on the present state of the flash smelting process and the impact of the increasing environmental awareness at NA.

Jan 1, 1993

By Peter J. Szabo

INTRODUCTION The time period from the detailed feasibility study to the post investment audity usually ranges from three to eight years depending upon the nature of the mining project considered. It is the only after the post investment audit that we know the adequacy of the assumptions made concerning operational risk assessment in the detailed feasibility or acquisition economics. The post investment audit results from numerous mining projects can best be described by a verse by John Greenleaf Whittier's Maaud Muller. It reads "For all sad words of tongue or pen the saddest are these 'It might have been!"' Dissecting the negative results of numerous mining projects we find faulty assumptions concerning markets, geology, capital investment and operational risk assessment. Although in hindsight many of these assumptions could have been considered impossible or impracticle to have forecast with any degree of certainty, we find that refined assumptions concerning operational risk assessment could have been made with only a modicum of additional "Due Diligence". Anyone who invests in a mining property should employ a much higher discount rate of future cash flow, (usually in the minimum range of 25%-30%), than he would expect from such safe investments as Treasury Bills or high grade Utility Bonds. The nature of this steep discount translates to a large uncertainty concerning the timing and actualization of assumptions contained in the detailed feasibility study. We must remember that when a project gets beyond 20 years, any contribution to the value of the project of cash flow is minimal due to the nature of the discounting process. Thus for each full or partial day lost in the development or early operation stage of a project, the financial impact will be greater than similar lost days later on in the project. Adequate operational risk assissment is particularly critical when bidding on competitive tenders for coal deposists in remote locations such as the Bowen Basin in Queensland, Australia. Because of the market attractiveness of these coal deposits for supplying end users in the Far East, Middle East and Europe, state governments require competitive tender biddings via the Authority to Prospect process. Front end bonuses and super royalty payments must be commited before the actual mining conditions are known. Time to submit firm offers from the actual request for proposal vary from 90 to 120 days. Thus any operational risk assessment must be detailed, realistic and reflective of the actual project. When one searches the literature, one finds limited qualitative data on operational risk assessment in valuation papers. Usually this facet of valuation takes a secondary role to such areas as reserves, markets, and environmental considerations. When one comes to the question of operational risk assessment more often than not one finds the use of "rules-of-thumb", such as tons per man shift, average production, average seam height, etc., are used to forecast results on which banks and other financial institutions are required to make investment decisions. Because of the extremely competitive environment of the 1970's and 1980's numerous financial institutions approved loans without adequate "Due Diligence", and are currently paying a steep price in terms of non performing loans and charge offs. One must always remember that each operation is unique with its own characteristic

Jan 1, 1985