Search Documents

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company's mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By D. A. Horne, V. R. Daiga

Certain steel mill wastes contain significant amounts of zinc oxide due to the use of galvanized scrap during the steel making process. Typically electric arc furnace (EAF), and basic oxygen process (BOP) flue dusts contain 20 to 30% zinc oxide and 40 to 50% iron oxides, along with smaller quantities of lead and cadmium. These materials can be recovered from the flue dusts by using a proven rotary hearth furnace (RHF) process. By-products of the recycling operation include a crude zinc oxide fume, which is captured in a baghouse filtering system, and sponge iron that may be recycled into the steel making operation. Crude zinc oxide properties plus the operating experience from two commercial RHF installations utilizing MR&E's DRyIron™ Process will be presented.

Jan 1, 2000

By T. Lamond, J. O. Costello

Marble is a preferred surfacing material in up-scale buildings. Its use increased in the 1870's with rising national wealth and declined in the 1950's when synthetic materials for these applications were developed. Natural marble is now limited to high-end domestic and commercial structures. Cultured marble is a paste of white marble dust and polyester resin cured in molds yielding fixtures of specific finished dimensions. Dyes incorporated at different stages in the mixing cycle mimic shades and veining of natural marble. This paper discusses the filler requirements for cultured marble production and reviews new techniques to cut and finish natural marble.

Jan 1, 1999

By J. O. Costello

Marble is a preferred surfacing material in up-scale buildings. Its use increased in the 1870's with rising national wealth and declined in the 1950's when synthetic materials for these applications were developed. Natural marble is now limited to high-end domestic and commercial structures. Cultured marble is a paste of white marble dust and polyester resin cured in molds yielding fixtures of specific finished dimensions. Dyes incorporated at different stages in the mixing cycle mimic shades and veining of natural marble. This paper discusses the filler requirements for cultured marble production and reviews new techniques to cut and finish natural marble.

Jan 1, 1999

By Takahiko Okura

Most non-ferrous raw materials are associated with sulphur. To extract the metals, the sulphur is recovered typically as sulphuric acid or liquid SOz, On the other hand, natural gas may contain over 20% of hydrogen sulphide (HzS) and a huge quantity of elemental sulphur is produced through oil and gas refining processes in the world. A large fraction of the sulphur mined from natural sources is eventually returned to the earth as fertilizers, by-products of desulphurisation and neutralisation processes, or as fugitives to the atmosphere. However, the supply and demand for sulphur are in imbalance. Such situation urges to develop a new smelting process without sulphuric acid production. This paper briefly reviews the global sulphur balance and the technologies for recovering elemental sulphur. The core of this paper is a proposal to convert SO2 gas to elemental sulphur by using organic materials. Some results of thermodynamic calculations and experiments are presented.

Jan 1, 2003

By Takahiko Okura

Most non-ferrous raw materials are associated with sulphur. To extract the metals, the sulphur is recovered typically as Sulphuric acid or liquid S02. On the other hand, natural gas may contain over 20% of hydrogen sulphide (H2S) and a huge quantity of elemental sulphur is produced through oil and gas refining processes in the world. A large fraction of the sulphur mined from natural sources is eventually returned to the earth as fertilizers, by-products of desulphurisation and neutralisation processes, or as fugitives to the atmosphere. However, the supply and demand for sulphur are in imbalance. Such situation urges to develop a new smelting process without sulphuric acid production. This paper briefly reviews the global sulphur balance and the technologies for recovering elemental sulphur. The core of this paper is a proposal to convert S02 gas to elemental sulphur by using organic materials. Some results of thermodynamic calculations and experiments are presented.

Jan 1, 2003

By Onuralp Yücel, Mehmet Bugdayc, Murat Alkan

"In this study, iron based alloys (Fe-Mo, Fe-Cr-Ni, etc.) were produced by using aluminothermic methods starting from Mill Scales obtained continuous casting processes. Mill scales are an oxidised layer of steel alloys containing iron oxide, which includes + 2, + 3 values, on the surface of slabs and billets occurring during annealing in heating furnace at integrated iron and steel milling plant, and continuous casting unit. In the metallothermic experiments, different ratios of starting mixtures and addition of the oxide powders (Alz03, Si02, CaO, MgO) were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis process (SHS) has many favour compared to the furnace applications, such as low energy requirement, low cost, very short processing time and simple operation, [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. Mill scale is a layer of iron oxide which forms on ferrous materials cooling after being processed in hot rolling or continuous casting plants. Mill scale contains iron (II) and iron (III) oxides, which result in a 70% total iron content in oxide form. Not being able to reuse this material will prevent the raw material entering the production plant from being fully utilized [5]. This study aimed to produce Fe-based alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys by using high metallic iron content by reducing continuous casting mill scale."

Jan 1, 2013

By Edmundo Manilla, Merete Tangstad, Daniel Davila, Eli Ringdalen

FeMn alloys are typically produced with lumpy ore or sinters. Minara Autlan, the Mexican FeMn producer, is however making Mn-nodules as a raw material for Mn-alloy production. The Mn nodules have been characterized by XRF, XRD, by wet chemical methods and by EPMA. The Mn/Fe ratio is somewhat lower compared to commercial Mn ore on the marked. The basicity of the ore is however close to 1, and additional fluxes may not be used. The Mn-nodules will be in a state of manganosite (MnO), tephroite ((Mn, Ca)2SiO4) and galaxite ((Mn,Mg)Al2O4). This leads to a low melting temperature area. A low porosity and low amount of higher Mn-oxides gives a high thermal strength to the nodules.

Jan 1, 2016

By M. Wallin

Millions of tons of sludge from different metallurgical processes are produced worldwide annually, and the environmental impact of landfilling these often hazardous sludges stresses the need to understand their role as valuable resources. The current work explores the potential of producing a saleable low-phosphorous ferromanganese alloy by utilizing sludge from the silicomanganese industry together with an iron source. The aim of the project is to explore the feasibility and practical challenges related to reduction and dissolution of manganese and silicon from the sludge to liquid metal and slag. Parameters such as ratio of input material as well as the effect of adding limestone and coke to the mixture were explored by thermodynamic calculations and adapted experimentally. Results show that a ferromanganese alloy, in fact, can be formed, while silicon and calcium forms a complex slag that captures a significant amount of impurities.

By Theodore Swann

DURING recent years, there has been a material increase in the use of ferrophosphorus in the steel industry. It has been observed, when rolling sheets, that those made of Southern iron did not have to be rolled at as high a temperature as the others and, consequently, did not stick together. The reason was found to be the phosphorus content of Southern iron. It was therefore thought that an addition of phosphorus to sheet steel of other than Southern origin would give the same result as the use of Southern iron. At first, this addition was made by intro¬ducing phosphate rock in the blast furnace and reducing it together with the iron ore; but, because of the necessity for only small quantities of this grade of iron, the process was not satisfactory. The manufacture of ferrophosphorus was then introduced, so that additions might be made to the open-hearth furnace or ladle. Ferrophosphorus was first manufactured in the blast furnace. This method, however, can only economically produce a grade of product up to about 20 per cent. To produce a higher grade, it would be necessary to charge a larger proportion of phosphate-bearing material; and as the rate of absorption by the iron is low, there would be an increased loss of phosphorus oxides. This feature makes the production of a higher grade ferrophosphorus in the blast furnace uneconomical. The use of high-grade ferrophosphorus in the steel requires a smaller addition and involves, besides the economies in handling, an additional economy in transportation. The alloy with a higher percentage than 20 per cent. can be made only in the electric furnace. In the ordinary operation of the electric furnace in the production of ferrophosphorus, an alloy may be produced containing 26 per cent. phosphorus; this is the limit, for it does not seem possible to produce a higher phosphorus alloy even if large excesses of phosphatic materials are used. The reasons for the difficulty in raising this percentage of phosphorus are not known. The compounds Fe3P, containing 15.6 per cent., and Fe2P, containing 21.7 per cent. phosphorus, have been studied and it appears as if the alloy produced, containing percentages of

Jan 10, 1924

Crandallite and millisite in Christmas Island 'B' and 'C' phosphate ores are rapidly decomposed by sodium hydroxide solutions at about 80QC. As these phosphates generally contain less than 1% silica, an alkaline extraction process can be designed, in which up to 95% of the sodium hydroxide used, may be recycled. The insoluble residue consists of an impure, highly reactive apatite, which in pot trials, has given good responses as a direct application fertiliser; alternatively this residue can be underacidulated to give a granular product with fertiliser potential. The hot leaching solution contains up to 95% of the alumina and approx- imately half of the phosphate from the original ore. Simple crystallising techniques have been developed on a laboratory-scale to use this leaching solution for producing smelter-grade alumina and detergent-quality trisodium phosphate. As the demand for detergents is limited, an investigation was made of the reaction between trisodium phosphate and slaked lime, derived from a high-grade New Zealand limestone occurring near Oamaru. The product is calcium phosphate, containing up to 40% P205, and less than 0.2% each of iron, aluminium and fluorine, and it should be a useful raw material for phosphoric acid manufacture. A preliminary economic evaluation of the whole process looks promising, And warrants further investigations, including pilot-plant work.

Jan 1, 1971

By M. M., Fine

In a laboratory study of grinding and classification' of silica sand, a satisfactory means of producing the medium-fine specification sand desired by producers of flint-glass containers was developed. The best procedure consisted of ball-mill grinding and double classification, which gave a properly sized sand containing less iron than the feed.

Jan 1, 1950

By D. J. Zhao

The reduction and nitridation of preoxidized ilmenite pellets were investigated with the prospect of creating grain refiners containing titanium oxides and titanium nitride dispersoids. All the reduction and nitridation reactions were conducted in a furnace with a thermogravimetric analysis system under a H2-N2 gas mixture of 5 L/min. The ilmenite pellets were reduced at 1100°C for 4 hours under 80%H2-20%N2 gas mixture, and then respectively nitrided at 700°C, 800°C, 900°C and 1000°C for 12 hours under 10%H2-90%N2 gas mixture. The products were characterized by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM), and analyzed by Energy Dispersive Spectrometers (EDS) and Electron Probe Mapping Analysis (EPMA). Iron oxides were reduced into metallic iron, and oxides of titanium were found, but titanium nitride particles were not identified in the products under the prevailing conditions.

Jan 1, 2014

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Pravas Ranjan Behera

Red mud of Indian origin contains around 55% plus of Fe2O3 and is considered as a hazardous waste for the alumina industry. For production of one tone of alumina employing the Bayer’s Process, around two tones of red mud is generated from three tones of Bauxite. Conventional process of steel making is not devoid of environmental pollution. In the present investigation, efforts have been made to produce steel from red mud by adopting reduction roasting, magnetic separation and hydrogen plasma smelting route. Magnetic fraction, containing enriched iron oxide and minimal content of alumina, is produced following the first two stages which is then subjected to hydrogen plasma smelting process for production of steel. This novel concept follows a green path way for production of steel free from pollution and is termed as green steel. Further, the only by-product that is produced in the process, is water, which is eco-friendly and recyclable.

Jan 1, 2015

By G E. Craig, W. M. Williams

A simple, easily constructed apparatus suitable for the zone refining of iron and other reactive materials is described. After eight passes at one inch per hour, the iron produced showed a marked drop in hardness to 49 Brinell. In addition, an arbitrarily -defined recrystallization temperature was lowered by about 35°C and the rate of grain growth greatly increased. CERTAIN materials, of which iron is one, are so reactive that they cannot be zone refined in any known container without becoming contaminated. For such substances, the floating zone method ( 1) may be used. In this method, the specimen is supported vertically in an inert atmosphere and the molten zone supports itself by its own sur-face tension. The method was first applied to silicon (2) and has since been used for other reactive metals such as zirconium and titanium. Smith and Rutherford (3) have previously reported on the floating zone refining of iron; the efficiency of the method for reducing the car-bon content was demonstrated on

Jan 1, 1962

By T. Shibasaki

Purification of copper electrolyte at Naoshima is carried out by two stage liberation to completely depress copper and impurity ions followed by concentration of the solution to produce crude nikel sulfate as by-product. A new nickel recovering process has been developed and pilot tested recently. It consists of the following process steps.; neutralization of spent electrolyte from liberation section to remove free acid and most part of remaining impurity ions, refining and nickel concentration by solvent extraction, and crystallization of pure nickel sulfate from concentrated strip solution. This paper describes the results of laboratory and pilot plant tests, then briefly discusses feasibility of the proposed process.

Jan 1, 1987

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By H. M. Chance

RECENT research work has shown that coal can be produced, at reasonable cost, from almost all coal-mining districts containing not more than 3 to 8 per cent. of ash. From coal so produced, an abundant supply of coke, suitable for blast-furnace operation, can be made containing from 12 down to 6 per cent. or less of ash. These statements apply broadly to the Appalachian coal belt, including most of the mining districts in Pennsylvania, Ohio, West Virginia, Kentucky, Tennessee, and Alabama. The exceptions will generally be found among those coals carrying a prohibitive percentage of sulfur. Any gravimetric heavy fluid method of separation will effect a reduction in the percentage of sulfur, but this reduction may not be sufficient to produce, from coal unfit for metallurgic use, a product that can be so used. When a large part of the sulfur is in the form known as "organic sulfur, "or is present as very .finely disseminated and homogeneously distributed pyrite, possibly it cannot be eliminated from the low-ash coal produced. When the sulfur exists as pyrite in distinct layers, bands, or nodules, or when it is finely disseminated but is irregularly distributed, often a low-ash coal low enough in sulfur to make good metallurgic coke can be produced from relatively impure coals. It has generally been assumed that the quality of coke on which blast furnaces must be operated depends on the geographic location off the furnace, and that the grade of coke on which a blast furnace must operate is that produced from the best coal obtainable by careful mining; or if the coal is prepared by washing, hand picking, or other means by which the foreign impurities are removed, that the grade of coke on which the furnace must operate depends on what has been termed the "inherent ash" of the particular coal.

Jan 6, 1924

By A. S. Gendron

A brief description of Inco's ORC copper refinery tankhouse and the electrowinning tankhouse is followed by a comparison of the requirements for the production of the high-quality copper in both systems. The description will focus on both tankhouses, with emphasis on experience to date in the electrowinning tankhouse. Particular attention will be paid to sensitivities of each tankhouse to process upsets which can. significantly afject the quality of the product cathodes.

Jan 1, 1977

By A. An. Mushketov, A. Al. Mushketov, N. A. Sopina

"INTRIDUCTION At present, more and more metallized raw materials with a metallization degree of not less than 80% are used in the smelting of steel. The main quantity of this raw material is produced in furnaces of mine type. Advantages of this type of raw materials for metallurgical processing are low levels of harmful and slag-forming impurities and a high content of metallic iron. At the same time, the cost of smelting raw materials and obtaining high-quality steels are reduced. In addition to the undoubted merits of metallized raw materials, there are high requirements for the quality of iron concentrates, which are the starting material for metallization: the mass fraction of acidic oxides should not exceed 3%; The mass fraction of iron should not be less than 69%, mass fractions of harmful impurities (phosphorus, arsenic, sulfur, copper, etc.) should not exceed 0.02%. These requirements are dictated by the fact that the recovery of burned pellets is carried out by gas in a solid phase. In this case, the empty rock and harmful impurities from the metal are not separated and sent to the steelmaking unit, increasing the heat consumption for heating and worsening the quality of the steel. The combined production of high-quality concentrate and metallized raw materials requires a large capital outlay from the enterprise, which in the future can be compensated for by increased profit from the sale of more expensive marketable products. At present, in the territory of Russia and the CIS countries Lebedinsky mining-and-processing integrated works is the only enterprise that carries out the entire chain of operations for the production of metallized raw materials, starting with the production of high-quality magnetite concentrate with a mass fraction of iron of 69.5% and ending with the production of a metallized product in the form of hot briquetted gland. JSC «SSGPO» is the largest iron-processing enterprise in Kazakhstan, which processes about 40 million tons of ore per year and receives 16 million tons of concentrate per year with a mass fraction of iron 66.0-66.5%. The technological scheme existing at the concentrator of JSC ""SSGPO"" includes the crushing of the feed ore to the size of 20-0 mm; dry magnetic separation operation; three reduction stages to a fineness of 90-95% kl-0.071 mm; operation of desliming, wet magnetic separation and filtration of the concentrate. Dry magnetic separation of the feed ore makes it possible to remove from the process of 19.6% of the tailings with a mass fraction of the total iron 12.5%, of magnetite 2.2%. The first reduction stage is carried out in rod mills with the volume of 40 m3 to a size of -1.6 + 0.0 mm. The first stage of wet magnetic separation is carried out in counterflow magnetic separators PBM-P-150/200L. The magnetic product of the first stage of WMS is classified in hydrocyclones; sands enter the second reduction stage into central discharge ball mill 3600 × 5000. Runoff of mills enter on the second enrichment stage in counterflow magnetic separators PBM-P-150/200L. The magnetic product enters the classification of the second stage, forming a closed cycle. Mass fraction of the class -0.071 + 0 mm in classifications runoff of the second stage is 70-75%. The second stage classifications runoff is transported toWMS-III operation in semi-counter separators PBM-PP-120/300. The magnetic product of the third stage enters the classification of the third stage. Granular residue are transported to the reduction of the third stage into central discharge ball mill 3600 × 5000. The mill runoff enters the third stage of classification, forming a closed cycle. Classifications runoff of the third stage enters on deslimation. Deslimed product is sent for fine screening to the crasher «Derrick» 2SG48-60W-5STK with a cell size of 0.1 mm. Top size of crasher is sent to regrinding. Undersize with a mass fraction of the class -0.071 + 0 mm 90-95% is fed to the wet magnetic separation of WMS-"

Jan 1, 2018