Search Documents

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device IntroductionTwo recent regulations have modified operators’ rock dusting schedules in order to meet compliance standards. First, the 80 percent incombustible requirement in intake entries has increased both on-section and out by the- section rock dusting. Secondly, the recent change to the respirable dust regulation has increased the number of respirable dust samples taken per sampling cycle. Previously, when only five samples were needed bimonthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule.The significant number of samples now required under new regulations, combined with the need to maintain 80 percent total incombustible content in active mining areas, require the schedules for respirable dust sampling and rock dusting to overlap. Although rock dust is considered a nuisance dust in relation to U.S. Mine Safety and Health Administration (MSHA) sampling, these overlapping schedules raise concerns about the amount of rock dust that potentially is included in the sample. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 effective Aug. 1, 2016, increasing concern that rock dust contamination may be an issue (MSHA, 2016). Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application, or to schedule rock dusting during a maintenance shift when the number of miners present is lower."

Jan 5, 2017

By Wallace W. Roepke, Richard C. Olson

To adequately attack the longwall dust problem, the US Bureau of Mines funded a contract to define dust sources on a longwall mine face area. The study examined the shearer during sumping, cutting, and tramming, the conveyor, and the roof supports. Tests showed the shearer to be the major dust source. Introduction Long-term illnesses place a heavy burden on miners, the mining industry, and taxpayers. Black lung payments to more than 400,000 miners and their survivors exceeded $9 billion between 1970 and 1980. They are continuing at a rate of $1 billion per year. Recent MSHA data indicate more than 50% of the longwall faces are still out of compliance with the 2 mg/m3 (0.00007 oz per cu ft) respirable dust regulation. Allowable dust limits are often further reduced owing to the presence of silica dust. This substantially increases the problem's severity. Research in the 1970s showed that by modifying the mining method through changing drum-type mining machines from high rpm shallow cutting to slow rpm deep cutting, both specific dust and energy could be reduced (Black et al., 1978; Ludlow and Wilson, 1982; Roepke, Lindroth, and Myren, 1976). The coal mining industry is using more longwall equipment to economically obtain high productivity. This high production rate, however, makes it difficult for longwalls to meet the legal dust standard. Research is showing how both these concerns may be addressed at the mining face. Results reported here explain the relationship of various major elements of the longwall system to dust generation on the longwall face. This paper is based on work completed by Foster-Miller Associates Inc. Objectives were to differentiate dust sources on the longwall face and to quantify dust levels for various elements of the shearer drum. The work was accomplished in two phases. Jonathon Ludlow, project engineer for FMA, developed and performed the necessary testing (Ludlow and Marshall, 1983). Bradley, Hadden, and Weston (1983) have done evaluations on British coal mines that produced similar results to those reported here. They found causative rela¬tionships between haulage speed, production, depth cut, drum speed, and dust generation. They also found that roof support movement increased the dustiness, whereas this work indicated that support movement had only a minor effect on total dust exposure. Both of these results are valid when the variation of mining conditions is analyzed. British mines are deeper than US mines. Therefore, roof rocks and coal are more fragmented than in the shallower US mines. Other reasons for the dust differences include the weaker shales found in Britain and the variation of roof support equipment designs between the UK and the US. Four mines in this report had rock roofs and, thus, would be less dusty. The fifth longwall mine had a coal roof, but the large cross-sectional area and high air velocity minimized dust exposure. Mines and Equipment Five underground longwall mine sites were tested (Fig. 1). All were using double-ended ranging-drum shearers (derds) with some variations in equipment. The mines and equipment details are shown in Table 1. No modification of mining equipment or operating cycles was made during the first phase of testing. The mining process observed followed the normal mine operating procedures. Three GCA RAM-1 respirable dust monitors and two vortex anemometers with cycle notations on portable tape recorders were used in each face area. The start and end of each cycle segment were recorded. Dust monitors record the dust levels once every 10 seconds, thus providing a relatively continuous real time indication of change in

Jan 8, 1984

By D. L. Nussear, W. E. Wallace, N. Clark, M. Gautaum, G. Hong-Guang

"Results of a research effort directed towards identifying and measuring the genotoxic properties of respirable particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented. Particulate matter emissions from a direct injection diesel engine have been sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust from a caterpillar 3304 diesel engine, representative of the ones found in underground mines, rated 100 hp at 2200 rpm is diluted in a multi-tube mini-dilution tunnel and the particulate matter is collected on 70 mm fluorocarbon coated glass fiber filters as well as on S"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the genotoxic potential. Results to-date on diesel exhaust have indicated that use of a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offers a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within. Protocols have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surf ace and physical properties of the particulate material. Evidence has been gathered to show that diesel soot expresses mutagenic potential as dispersions in DPL in the Ames tests as well as sister chromatid exchange activity in the animal lung fibroblast ·derived V79 cell line. The results are comparable to the standard solvent extraction procedure. INTRODUCTIONDiesel engines are primarily associated with transportation; however, they are also very common in the work place. Of particular concern is the use of diesel engines in mining operations. Currently there are 1,950 diesel machines working in underground coal mines throughout the country. These units are used in 151 mines encompassing nine different states (MSHA, 1991). It is believed the use of diesel powered equipment has contributed to higher productivity in these mines. However, the exhaust from diesel engines operated in underground mines has been a subject of concern during the past decade because of its suspected relationship with health aspects. The particulate matter generated by the diesel engine is of particular concern."

Mar 1, 1992

By Cheryl Hill, Michael Keane, Pamela Mike, Raghoottma Pandurangi, William Wallace, Mohindar Seebra, Val Vallyathan

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte bemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz and kaolin dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect of lecithin adsorption. Dust hemolytic potential versus medium pH is presented. Fourier transform infrared spectroscopy and photo-acoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis. INTRODUCTIONQuartz dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction.In the alveolar ·spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, among other functions, mechanically stabilizes the lung from collapse by reducing the surface tension of water in the alveolar sacs.1 This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11 % in dog lavage fluid), and phospholipids (about 88%).2 Pbosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalmitoyl lecithin (DPL).2 Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occurring upon deposition of a particle in a pulmonary alveolus. As may be seen from Figure 1, the DPL molecule has several fixed charges at neutral pH; a positive charge on the trimethylamine (choline) moiety, and a negative charge on the phosphate group. Also evident are the two fatty acid residues of palmitic acid, which are bonded through ester likages to the glycerol segment of the molecule. The fatty acid moieties of phosphatidyl choline make the molecule inso1uble in aqueous solutions under normal conditions, but a colloidal unit of aggregated molecules called a micelle is usually formed spontaneously above a certain minimum concentration. Small micellar vesicles are generally formed in the laboratory by using ultrasonic agitation or by solvent evaporation methods."

Jan 1, 1990

By W. Jacobi, F. Steinhausler, A. C. James

INTRODUCTION In 1979 the Committee on Radiological Protection and Public Health of the Nuclear Energy Agency (OECD) defined a programme of work needed to improve radon dosimetry and monitoring. A Group of Experts in this field was established by the NEA and at the first meeting of the Group the authors were designated an initial task with the following terms of reference:- To review dosimetry of radon, thoron and their daughters, and in particular:- - to examine analytical models for the assessment of dose to individuals who are exposed to aerosol mixtures of these nuclides; - to examine the state of knowledge of the characteristics of aerosol mixtures of these nuclides and other factors that influence the dose to the lung, and identify those parameters which should be measured for dosimetric purposes in radiological surveillance programmes; - to identify areas where further study or research are needed. In this presentation we attempt to examine, with these objectives, the relationship between exposure to radon and thoron daughter aerosols expressed in terms of the working level month l (WLM), or its SI equivalent, and dose accumulated by sensitive tissues of the lower respiratory tract. Over the past two decades many attempts have been made to calculate the lung dose equivalent to l WLM exposure in mine atmospheres, usually in terms of the maximum dose to basal cells in a small part of the bronchial tree. The calculations have employed variously detailed models of airway anatomy, aerosol deposition, ciliary clearance and dosimetry of tissue at the bronchial surface, and are well reviewed elsewhere (Walsh, 1970; UNSCEAR, 1977; Jacobi, 1977; Fry, 1977). They agree in the conclusion that basal cells in segmental bronchi (between about the third and fifth bronchial generations) receive the highest dose, although estimates of this dose differ by more than an order of magnitude, ranging from about 0.2 to 12 rads per WLM (2 mGy to 120 mGy). The most critical parameters of these models are the assumed depths of basal cells below the bronchial surface and the fraction of the WL carried by free ions. When more realistic values of these parameters are substituted (Jacobi, 1977), the dispersion in calculated maximum doses to basal cells is reduced to give a much smaller range from about 0.3 to 1 rad/WLM (3 to 10 mGy/WLM). The parameters and methods employed in these various models, however, remain too diverse to infer the sensitivity of the dose conversion to practical variations in aerosol characteristics and the additional factors determining lung deposition and clearance. We have therefore taken the approach of developing newer models (Jacobi and Eisfeld, 1980; James et al, 1980) that can encompass the range of available experimental data on the physical and biological behaviour of radon and thoron daughters and also accommodate the different interpretations that can be put upon them. We have paid particular attention to the averaging of dose over tissues of equal sensitivity in the lung

Jan 1, 1981

By Iván Mendoza

La Responsabilidad Social Empresarial (RSE) es una política que adoptan las empresas de manera voluntaria -en tanto relaciona las empresas mineras que instalan las unidades operativas y las poblaciones del entorno. En ese sentido, el presente texto describe los lineamientos que comprende dicha política. Luego, se desarrollan las diferencias entre los ámbitos económicos, organizativos e institucionales en las zonas rurales del país. El aspecto organizativo se aborda enfatizando el papel de las comunidades campesinas, mientras que el institucional destaca los roles de las municipalidades. Finalmente, se revisan las relaciones entre las empresas y la población.

Jul 1, 2013

By Xin Zhou, Huilin Jia, Xiaofei Liu, Jinxin Wang, Zifeng Meng, Zinan Du, Hui Xie, Guihang Jiang

The change of gas emission or concentration level at the working face is one of the main precursor characteristics of coal and gas outburst. At present, coal and gas outburst monitoring and early warning are mainly based on whether it exceeds the limit and its change law. However, the gas concentration level is affected by factors such as coal seam gas content, permeability, and mining process, and the change law is complex to recognize manually. In this paper, the response characteristics of gas concentration level in the mining process are analyzed and revealed, and a bidirectional long short-term memory model is established. The change characteristics of the gas concentration level in the mining and non-mining processes are studied and recognized. The results show that the change law of gas concentration in the mining process has apparent periodicity and trapezoidal volatility. The proposed intelligent recognition method based on the bidirectional long short-term memory neural network can automatically recognize the underground mining and non-mining processes, and the recognition accuracy achieves 97.7% . The research can significantly help improve the level of coal mine safety management and the accuracy of early warning of coal and gas outburst.

Apr 29, 2023

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan, J. H. Kang

"We have reported previously that crushing or grinding crystalline silica results in the generation of silica-based radicals on the particulate surface and that these radicals can generate hydroxyl radicals in aqueous solution. Data in the present study indicate that freshly ground silica is more cytotoxic and is a more potent activator of alveolar macrophages than comparably sized aged silica. That is, compared to aged silica, fresh silica is 4.2-fold more potent in decreasing the membrane integrity of macro· phages; is 50% more potent in activating hydrogen peroxide secretion by macro· phages; and is 4.frfold more potent in stimulating cellular chemiluminescence. Prosil 28, an organosilane material, is an effective coating agent for fresh silica. It decreases the cytotoxicity of fresh silica by as much as 78% and decreases the ability of fresh silica to induce chemiluminescence from alveolar macrophages by 58%. The data suggest that surface radicals associated with freshly cleaved dust may be an important factor in the induction of pulmonary disease. Furthermore, treating dust with coating agents may substantially decrease toxicity. INTRODUCTIONThe U.S. Department of Labor estimates that over 1.25 million American workers may be exposed to crystalline silica and that nearly 60,000 may be at risk of developing some degree of occupational lung disease (Parkes, 1982; Peters, 1986). Occupations of concern include miners, stone quarry workers, sand and gravel workers, sandblasters, foundry workers, and glass workers. Acute silicosis is characterized by inflammation, alveolar lipoproteinosis, and the rapid development of respiratory disability (Banks, 1986). In contrast, chronic silicosis develops 20-40 yr after initial exposure and is characterized by the appearance of concentric hyalinized nodular lesions and the progressive development of dyspnea (Parkes, 1982; Ziskind et al., 1976)."

Mar 1, 1992

By Gennaro G. Marino

This paper summarizes and evaluates data on mine subsidence ground movements and associated damage for houses in Illinois. Based on the data collected, the response of homes to subsidence ground movements is expressed in terms of repair costs. A damage criteria is then proposed that relates the ground movements and damage levels. The data were collected as part of a comprehen¬sive study performed for the Illinois Abandoned ?Lined Lands Reclamation Council, A -M-RC, by the Civil Engineering Department at the University of Illinois, and probably will be published in late 1934 by the council. The study concentrated its efforts on surface ground movements and the effects to houses over abandoned room and pillar mines. The resultant surface subsidences are commonly dish or bowl shaped and are termed sags. Method of Analysis The steps in analysis used to arrive at the proposed damage criteria are: 1. Canvas and rap subsidence damage in houses, 2. Assess the associated ground movements, 3. Estimate the damage repair cost, 4. Develop a damage/repair level classifica¬tion, 5. Correlate the associated ground movement, damage/repair level and home construction type, 6. Propose a damage criteria.

Jan 1, 1984

By N. Saeidi

"For a mine section comprising 100 different stoping activities, there are ~10158 different possible stoping sequences to explore in the mine schedule optimization search and this figure is indicative of the challenge posed in maximising profitability through mine schedule optimization. Any viable excavation timetable must satisfy all conditions that will constrain feasible sequences. In general, consideration of additional constraint will tend to reduce profitability. Geomechanical constraints on mine schedules, introduced with the aim of avoiding excavation instabilities, can be established for underground mine schedule optimization processes but, currently, this is done only rather crudely; precedence relations between excavation activities (stoping or development) are encoded to produce particular stope sequence patterns (e.g. ‘chevron’ or pyramidal sequences).The work reported aimed to investigate automated processes for formulation of such geomechanical constraints. The timetable optimization approach to the problem precipitated a fresh look at time dependent, and excavation sequence dependent, deformation. Abundant evidence emerged that supported the notion that any methodology developed that failed to account for such time and sequence dependencies was itself bound to failure. Yet, it was also recognised that any deviation at all from an assumption of linear elasticity for geomechanical numerical modeling, adopted to inform geomechanical constraint formulation, would rapidly lead to impractical levels of computational effort.Thus the approach presented here represents a compromise: the elastic stress fields induced by individual mining activities are computed for each activity, independently considered within a computational domain identical to that of all other activities. These are stored in a database. Instability risk for a specific sequence of mine activities can be assessed through superimposition of stress fields drawn from the pre-computed database. Time stamps allocated to events corresponding to the excavation processes permit the conversion of the sequence of elastic stress fields into a time table of stress fields. For specific locations within the computational domain, the aggregate effect of the sequence of mine activities leads to stress-time histories having a castellated appearance, a result of the near instantaneous response of an elastic medium to the excavation perturbations. Time dependent deformation responses are crudely allowed for through the re-profiling these castellated histories through graphical construction of curved responses, where the curve gradients are related to a viscous parameter. Such curves form the basis for a geomechanical constraint formulation to be adopted for mine schedule optimization."

Jan 1, 2015

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

Opportunities to monitor and control primary grinding mill performance are strongly sought after in the mineral processing industry. Currently, limited on-line information about mill charge motion and content is available to mill operations for control purposes, leading to periods of lower throughput, instability, variable product size and accelerated mill liner and lifter wear. In response to this need, CSIRO has developed an on-line surface vibration monitor for primary grinding mills which produces data that has been shown to provide new information about the mill charge in terms of toe and shoulder position, as well as potentially key features such as the overall charge level, the distribution between rock and balls in the mill, and the impact of the charge on the mill liners and lifters. This paper outlines the key features of the on-line monitor system, particularly those relating to data transmission, data analysis, and the design of the monitor and its independent power supply. It describes the coupling of single vibration sensor data from the CSIRO on-line monitor to the actual operating conditions of a SAG mill and how the vibration response and hence mill operating conditions vary as a function of time, including during mill equipment failures such as a broken discharge grate. Opportunities for improved mill control based on the data from the on-line monitor are also discussed, as well as the implications in terms of mill processing and maintenance performance. Recently a CSIRO monitor was also installed on a ROM ball mill and analysis of the vibration sensor data from this installation is currently underway. Preliminary findings from this installation will be presented along with comparisons of generic information, such as toe position (measurement precision and operation variability) and vibration signal (intensity, sensitivity and operation variability), between this type of primary grinding mill and AG/SAG mills.

Sep 1, 2012

By E. Cauda, K. Phillips

"Diesel particulate matter (DPM) exposures are a serious occupational health hazard in underground mines. While the complex nature of DPM makes direct analysis difficult, its primary component, elemental carbon (EC), can be used as surrogate. The near real-time FLIR Airtec monitor measures EC mass based on laser extinction. It was developed for use in underground metal/non-metal mines, and calibrated to the NIOSH Method 5040. Its effectiveness has not been demonstrated in coal mines, however, where coal-sourced EC could produce analytical interference. To gain preliminary insights regarding the Airtec’s performance in the presence of coal dust, experiments were conducted in a controlled laboratory chamber. The Airtec EC results consistently underestimated Method 5040 EC for both respirable-sized and submicron coal dusts. While underestimation of coal-sourced EC bodes well for limiting coal interference for DPM measurement, one key reason for the observed trend was non-uniform coal particle deposition on the Airtec filter. This may be problematic in coal mines where DPM and coal dust occur together in the instance that DPM deposition is also non-uniform. INTRODUCTION Diesel particulate matter (DPM) is an occupational health hazard, and underground miners have the potential for relatively high exposures due to their work in confined environments with large diesel equipment (NIOSH, 2011). DPM is heterogenous and complex in terms of its chemical composition (Birch & Cary, 1996; Noll et al., 2006), but elemental (EC) and total carbon (TC) are often used as analytical surrogates (Birch & Noll, 2004; Noll et al, 2015). EC is the solid “soot” component of DPM, whereas TC also includes particulate organic carbon (OC) (Noll et al., 2007). EC and OC can be measured in filter samples using the standard NIOSH Method 5040 (NIOSH, 2003), and summed to obtain TC. In US mines, TC has been adopted as the analytical surrogate for DPM in regulatory activities. In metal/non-metal mines, personal exposures are limited under 30 CFR Part 57. In coal mines, limitations are made on emissions from each piece of equipment (30 CFR Part 72) rather than for personal exposures. This is because coal dust has the potential to interfere with TC measurements in personal samples. In some other countries, and for non-regulatory purposes in the US, EC is also commonly used as a surrogate for DPM in mine monitoring applications [e.g., see AIOSH, 2013). EC generally exhibits a linear correlation with TC (Birch & Cary, 1996; Noll et al., 2006 and 2007) but unlike TC measurements, which are analytically intensive, EC can be determined more simply using a laser absorption/extinction principle on filter samples (Noll et al., 2013)."

Jan 1, 2019

By John Tatom, Michelle Crull, Robert Conway

The US Department of Defense Explosives Safety Board is sponsoring the development of a risk-based explosives safety siting program, SAFER. The fragment and debris hazard generated at the potential explosion site (PES) is critical at an exposed site (ES) over a significant range of standoff distances. The Science Panel Impact Debris Evaluation and Review (SPIDER) test program has been planned to develop improved predictions for the hazards inside an ES by fragments and debris. Data will include the mass and velocity required for perforation of the test cross-section and the characteristics of all debris produced inside the ES.

Jan 1, 2010

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011

By Xuezhong Wang, Hao Guo, Tao Tu, Qingsheng Liu

The scheelite concentrate was leached with a mixture of sulfuric and oxalic acids. Chemical compositions, mineral phases, and morphology were characterized by XRF, XRD, and SEM–EDS. Based on the results of the single-factor experiments, the response surface methodology (RSM) was chosen to optimize the leaching parameters: temperature, time, and concentrations of sulfuric and oxalic acids. The RSM results indicate that the optimum values for those parameters are as follows: temperature 72 ℃, sulfuric acid concentration 1.48 mol/L, oxalic acid concentration 0.96 mol/L, and reaction time 2 h. Under the optimal leaching conditions, the model predicts a maximum leaching yield of 99.5%, compared to the value of 99.1% obtained experimentally, that is, a discrepancy of only 0.04%. This good correlation shows that the quadratic polynomial equation obtained by the RSM optimization is reliable. The importance on leaching parameters of scheelite is, in decreasing order, temperature, time, sulfuric acid concentration, and oxalic acid concentration.

Oct 11, 2021

By Jingzhi Liu, Xueping Hu, Huai Wang, Simin Yang, Baoqiang Yu, Deguang Zhan

In this study, response surface methodology (RSM) and Box-Behnken design to improve copper extraction from refractory copper oxide ore were investigated. Based on single factor tests, quadratic polynomial equation to describe the relationship between influencing factors (particle size, leaching temperature, sulfuric acid concentration, leaching time) and copper leaching rate could be obtained by RSM. The optimum parameters determined by the model are as follows: particle size 64.60% − 74 μm, leaching temperature 74.15 °C, sulfuric acid concentration 0.49 mol/L, and leaching time 140.85 min. Under these conditions, experimental copper leaching rate of 85.12% could be achieved, which was very close to the predicted maximum value (85.34%) by the model, indicating the quadratic polynomial model was accurate and reliable. Copper leaching rate increased approximately by five percentage points comparing to the result of single factor tests. This study indicates that response surface methodology is an effective method to optimize experiment conditions and achieve an ideal experiment result.

Aug 17, 2022

By Jian Liu

The study aims to leach copper from a low-grade flotation middling by optimizing the leaching process using response surface methodology. The effect of key parameters, i.e., sulfuric acid concentration, nitric acid concentration and leaching time, on the leaching efficiency was investigated and a quadratic model was suggested by the methodology to correlate the variables to the efficiency. The results indicate that the model is in good agreement with the experimental data at a correlation coefficient (R2) of 0.97 and the most influential parameter on efficiency was identified as sulfuric acid concentration. The optimum conditions for copper leaching from the middling were identified as sulfuric acid concentration at 103.74 g/L, nitric acid concentration at 12.50 g/L and leaching time of 30.98 min; under such a condition, an average leaching efficiency of 93.16% was achieved from the middling.

Jan 1, 2011

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By César Ugaz, Jorge Cardenas

Mitigating the vibrations resulting from a blasting rocks is one of the most common challenges that Peruvian mining has, since if this impact is not mitigated it can generate discomfort and altercations with neighboring communities and also puts the continuity of the mining project at risk. In that sense, we must establish control parameters to mitigate these effects as much as possible. As a starting point we must establish areas of interest that in this context would be the communities near the mine; first stage to carry out constant monitoring at these points, the registration of vibrations and noise is vital for the success of this control, with this information we can establish predictive models, the registration of elemental waves and the evaluation of human perception. In a second stage, this information allows us to make decisions in engineering such as the selection of delay times, elaboration of detonation sequence schemes, maximum amount of operating load per delay window, as well as the use of special load designs (Decks). There is a fear that these controls generate negative impacts to the process, referring to fragmentation, dig rate, throughput, etc. Since we limit the explosive load necessary for the results we need. To avoid this we use "Decks" type load designs under a sequencing between these under time calculations by elemental waves, which generate a reduction in vibrations up to 50%, also complying with strict regulations without affecting the power factors to comply with our performance indicators. Finally, in a third stage we must carry out a constant evaluation of results according to the progress of the mine.

Jan 26, 2026