Search Documents

Technically speaking, the concept of NDT sounds like the "magic bullet" when faced with a questionable drilled shaft. All the Contractor or Engineer needs to do is select an NDT method, apply it, understand the details and extent of the defect and determine whether it will impact the load carrying capacity of the shaft during it’s design life. Unfortunately, it is not that simple. NDT is a tool utilized to indirectly assess the condition of the completed drilled shaft. For the most effective interpretation, NDT data should be correlated with the subsurface information, visual observation, and detailed shaft installation records. The basis for acceptance or rejection of drilled shafts should not be solely based on NDT. The parties responsible for specifying, interpreting and using the NDT results must understand the capabilities and limitations of the method to be utilized, in conjunction with the relevant subsurface conditions of the site, before selecting and specifying a system and acting on the results. This is necessary so that an appropriate NDT method can be specified and contracted. In this manner the results and roles of the responsible parties can be clearly defined.

Jan 1, 2004

By Braden Lusk, Paul Sainato, Josh Calnan, Hiago Vasconcelos, Luis Felipe Marinho

"Blasting and rock fragmentation is one the most important unit operations in mining. Since itsintroduction into the mine production cycle, mining has become more efficient in mineral production(Hartman, 2002). Widely used with the main objective of breaking rock mass in smaller fragments to be loaded and hauled at a minimum cost, blasting is optimized when stemming materials properly confine drillholes charged with explosives. Halim Cevizci (2013) performed a stemming application using Gypsum plaster, a kind of material that exhibits solid-like behavior when it is dry. Based on his theory, the present article reports an experiment using another type of material that shows similar behavior, non-Newtonian fluids. The primary goal of this study is to measure the confinement effectiveness provided by a non-Newtonian mixture as the stemming component. The study also analyzes the explosives’ energy propagation throughout the rock mass relating to the stemming materials applied. Currently, mining literature recommends the application of dry granular materials in stemming columns, because of its inertial and high frictional effects (Hagan, 1973). However, the test verified that the mixture added to the stemming column was able to reduce energy and gas losses to the atmosphere, because of the liquid’s property of filling voids in the material. The solid-like behavior of the non-Newtonian mixture was investigated for its capability to improve borehole confinement, since the mixture reacts like a solid when under shear stress. The results were compared to those from sand and air stemming applications, configured in different arrangements. It was concluded that the non-Newtonian mixture yielded high results due to its better confinement effectiveness, a reduction of air overpressure, and an increase of the strain propagation and ground vibration throughout the rock."

Jan 1, 2016

By Dinesh P. Amalnerkar, Nagegownivari Munirathnam, Tirthalli Prakash, Katia Vutova, Vania Vassileva, Veliko Donchev

"A time-dependent model for electron beam melting and refining (EBMR) of different metals and alloys is developed. The model is 3D axi-symmetrical and an adapted numerical scheme of Pismen-Rekftord type is applied. The developed computer program computes the thermal fields in the metal ingots during EBMR process as well as the dynamics of the thermal streams and the geometry of the molten metal pools. Calculated results for different regimes of EBMR of titanium are obtained and discussed in the paper. Experiments are performed and impurities' concentration data are presented. Simulation results are compared with experimental data and are used for optimization of the EBMR process in the case of Ti.IntroductionElectron beam melting and refining (EBMR) has an important role in the special electrometallurgy[ 1-6] and it is approved for obtaining of pure titanium [7]. EBMR of metals and alloys is being recognized as a competitive and even the single method for obtaining new materials for all areas of human activity.The principal scheme of the EBMR drip process is shown in Fig.1. A thin layer of molten metal is formed on the front part of the feeding rod during the e-beam processing and generated droplets fall into the molten pool in the crucible where the ingot is formed. The refining is mainly realized at the boundary liquid metal - vacuum. There are three zones in EBMR (Fig.1) - on the front part of the feeding rod (zone I in Fig.1 ), on the surface of the generated droplets (zone II in Fig.1) and the surface of the molten pool in the water-cooled copper crucible (zone III in Fig.1)."

Jan 1, 2013

By A R. McKinnon

The recently opened Hera Au-Pb-Zn-Ag mine in central New South Wales has provided an ideal opportunity to demonstrate the calculation of sulfide ore mineralogy using normative methods. Normative mineralogy applies a set of sequential rules based on the species likely to be present to assign the chemical components of a sample to their respective mineral components. The dominant sulfide mineral assemblage present at Hera is galena, iron-bearing sphalerite, chalcopyrite, pyrrhotite and pyrite. A normative technique for estimating the relative abundance of each of these species from drill hole, grade control and metallurgical assay data sets has been developed. This includes a process for deriving a gangue iron value and differentiating pyrrhotite from pyrite using sulfur/iron ratios. A calculated total sulfide volume value has been utilised at the mine to improve interpretation of lode boundaries. Normative drill hole values have also been used for domaining within the orebody, with large scale mineralogical trends evident. Dry bulk density (BD) values calculated using a normative species-weighted method show good correlation with measured BD values (R2 = 0.895) and are a significant improvement on the Pb+Zn+Cu regression method (R2 = 0.646) previously used. Application of these calculations to identify errors in assay databases is demonstrated, with specific reference to the data set for the nearby Nymagee copper deposit. Validation of block model grades is also explored and a method to improve resource estimates using direct normative mineral interpolation is proposed. The integration of the normative data into the production and metallurgical data sets at Hera is described and the relationship of the normative minerals to other economic elements such as gold and silver is discussed.CITATION:McKinnon, A R, 2017. Application of normative ore mineralogy to geological and metallurgical data sets at the Hera Au-Pb-Zn-Ag mine, New South Wales, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 63–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Robert B. Hoy

To maintain a competitive position in the world market in spite of higher domestic labor costs, the U.S. has been forced to the forefront in developing labor saving devices. This has resulted in automation in our factories, mechanization in our mines, and development of faster and more economical methods of transportation. Since World War II the domestic mining industry has suffered perhaps more than any other sector of our economy. When we assisted our allies-and our enemies-to get back on their feet following the ravages of war we were perhaps overly generous in providing funds and technical assistance to develop foreign mining industries that have since become thorns in the side of our own industry. It has become imperative that domestic industry exert its vigor to meet the challenge of foreign competition. While the domestic industry can meet this challenge of foreign competition in part by protective tariffs, quotas and governmental aid, the most effective way is to maintain technological superiority that will reduce manpower requirements and costs and increase productivity. There is this opportunity both in mineral processing and in mining.

Jan 9, 1962

By P. Katsabanis

Numerical modelling was used to examine damage in wall control operations. Decoupled charges appear to create larger damage zones than fully coupled low density charges with similar charge distributions: Air was shown to be a very efficient coupling medium, while water coupling resulted in significant damage. However, Mach stems are formed when air is used as a decoupling medium, leading to compression of the charge ahead of the detonation wave. Air decked charges generate two damage zones, one close to the charge and another close to the air-deck/stemming interface, where pressure pulses are reflected. The extent of the latter depends on the length of the air-deck.

Jan 1, 2001

By A. Bastrzyk

Text The mining and refining of minerals generates large amounts of solid waste. The waste from cleaning operations constitutes up to 90% of the total production. Although some of them can be used in mining, civil enegineering, construction, agriculture, most of them must be disposed in dumps and slurry ponds, causing major economic and enviromental problems (Alonso, 2002; Alon-so, 1999). The refuse from minerals cleaning may have considerable valuable particles content, which can be used in industry. Thus, the recovery of these particles from minerals waste by using a cleaning method effective at fine particle size, may overcome these consequences. Surfactants are used in numerous applications including emulsification and solid surface modification. In the oil agglomeration of minerals, the ionic surfactants (both anionic and cationic) are used for the hydrophobization of mineral surface and the oil-water emulsion preparation. When the cationic surfactant is injected into the oil-water mixture, surfactant molecules adsorb at the oil-water interface, changing droplets? properties. The addition of anionic surfactant to the mineral suspension was found to modify the solid-liquid interface. In this paper, the condition and mechanism of selective separation of magnesite from quartz are presented. A satisfactory was achieved with the amount of anionic collector (sodium oleate) equal to 15.2 mg/gsolid and with the amount of cationic collector 27.9 mg/gsolid for cetyltrimethylammonium bromide (CTAB) and 16.9 mg/gsolid for dodecyloammonium hydrochloride (DDAHCl) at pH 8. At these conditions, the amount of agglomerated carbonates was about 12% for CTAB and 5% for DDAHCl.

Jan 1, 2014

By S. N. Mukherjee

Maintenance of equipment in Longwall faces plays a vital role in face performance. This is more prominent when shortage of spare parts and trained personnel occurs. A study was made in an operating Indian Longwall face for identifying the types and meantime between failures. Though the duration was not enough and study was not very elaborate, it revealed certain interesting facts. The machine availability was found to be poor, though a maintenance schedule was followed. Failure of simple parts like AFC chain connectors even resulted in loss of production of 10 times the complete chain cost. This pinpoints that a proper maintenance schedule is to be developed considering the human factors and local conditions existing in the particular country. Operations research techniques could be used in the process.

Jan 1, 1989

By D Xu

BHP Billiton Iron Ore is one of the world’s premier suppliers of iron ore. It currently has operations in Western Australia and Brazil and also has some iron ore interests in West Africa.BHP Billiton’s Optimisation R&D team has developed a proprietary mine planning optimisation tool that uses a mixed integer linear programming (MILP). This tool is called Blasor and it is used to rapidly evaluate the resource development potential (RDP) scenarios for the company’s business development strategy. In addition it generates life of asset (LOA) mine plans for the company’s operations and growth projects. The Blasor optimiser maximises the discounted operating cash fl ow (DCF) as the objective function, subject to mining, processing and transportation capacity constraints and blended product quality constraints. The paper will outline how Blasor has been applied to the resource development potential (RDP) strategy scenario studies, growth project evaluations and LOA mine planning within BHP Billiton Iron Ore.The practical application of Blasor to resource planning optimisation within BHP Billiton Iron Ore has demonstrated the value of such a tool for optimising strategic directions through the evaluation of a number of carefully proposed scenarios and maximisation of operational decisions, such as cut-off grade, open pit development sequence, etc. Particularly for the company’s business development direction studies, Blasor plays the role of a fair valuation tool in that it discovers the most valuable resource development scenario, thus establishing a sound basis for comparing the economic merits of each scenario.

Jul 11, 2011

By T. L. Joseph

THE committee appointed to investigate the application of oxygenated air to the blast' furnace believes, after a careful study of the problem, that this enriched air will increase hearth temperature, tonnage, flexibility of operation, and quality of pig iron made, and that fuel consumption will be decreased. These improvements are supported by theoretical evidence; but a practical trial of the process is necessary to establish more definitely the magnitude of benefits realized. The commercial application, however, may profitably be preceded by a test on a smaller scale. A small furnace will, in general, respond to the enriched air in the same way as a commercial furnace and the magnitude of the benefits to be gained from varying additions of oxygen can be fairly well established at relatively little expense. A new experimental furnace, being built jointly by the Bureau of Mines and the University of Minnesota, at Minneapolis, will have a capacity of about 6 tons and will riot require more than 700 cu. ft. of natural air per minute. Its hearth is 36 in. in diameter and its height about 32 ft. Enough oxygen to enrich the blast to the extent recommended by the committee can be obtained from a small oxygen unit. It might even be cheaper to perform preliminary experiments with tanks of oxygen obtained from regular, dealers. A procedure in making the test that suggests itself is to start with operation on normal air; then to use blast, enriched in several steps. Systematic temperature measurements of the tuyeres, slag, and metal would reveal any changes in hearth temperature. When these changes become large enough, the burden may be gradually increased to just within the breaking point and the furnace brought back to normal, if possible, by the addition of oxygen. Such a test would show what might be expected in the way of a decrease in fuel consumption and the time taken to "straighten up" the furnace by means of oxygen. The new furnace at Minneapolis is so equipped that the furnace process can be observed from the stock line to the iron notch. We have been taking gas samples at various elevations in the furnace to study combustibility of the fuel and the reducing power of the gas. If either of these is affected by removing inert nitrogen, the change can easily be measured.

Jan 11, 1924

By D. Gearhart

Full-scale tests are conducted on mine roof supports using protocols developed by the National Institute for Occupational Safety and Health (NIOSH) using the unique capabilities of the Mine Roof Simulator (MRS). These protocols simulate the loading conditions that the support will be exposed to in an underground mine to determine the performance capabilities and limitations of the support. Some tests are conducted with rigid boundary conditions, creating uniform contact and near ideal axial loading conditions. These tests are used to determine the ultimate performance potential of a support, including the strength, stiffness, and stability. For prop supports where stability is a critical design issue, tests are implemented to induce buckling by a modified end condition, eccentric contact, or biaxial loading. It is important to determine the cpacity of the support design when the support is subjected to unpredictable loading conditions. This paper examines the effect of end conditions and load profiles on prop support performance and applies a new analysis methodology based on eccentric loading to determine a factor of safety for load capacity. Recommendations for installation practices that minimize eccentricity and therefore preserve capacity are also provided.

Partition models are commonly used to assess the separation performance of circuits incorporating density-based processes. Unfortunately, this useful tool has traditionally been overlooked by the heavy minerals sands industry due to difficulties associated with the use of toxic dense liquids. In the present study, this problem has been avoided via the development of partition models based on experimental data from microscopic grain-counts. This technique, which uses different mineral species as density tracers, provides a new tool for evaluating the multi-stage circuits that are required to successfully upgrade heavy mineral sands. The partition model approach easily identifies shortcomings of existing circuits and, when used with conjunction with linear circuit analysis, provides tremendous insight regarding the optimum arrangement of unit operations in terms of separation efficiency and plant throughput capacity. An industrial case involving the redesign of a heavy mineral sand spiral plant is presented to demonstrate the utility of these process engineering tools in plant optimization.

Jan 1, 2009

By I. Gombköto

To sustain the growth of industrial production necessitates the increasing of the amount of processed mined raw and secondary materials. As a side effect of raw material production, the amount of tailings material, - coming from mineral processing operations ? increases as well. Using wet technology, these tailing materials are generally transported and stored with the water used for previous operations. This habit could lead to dangerous situations. Enough to remember the disasters had happened to the last decade, safe tailings operations need to remove as much water from the solid as possible. Environmental, technical and economical needs should meet, therefore using a technology combining these specific needs could be necessary. Paste technology was introduced generally into tailings operations at the last ten years, as an answer to the call of the above mentioned challenges, however there are still many questions to answer within the frame of using it. The Institute of Raw Materials Processing and Environmental Process Engineering of the University of Miskolc has been dealing with mechanical process engineering, especially by the support of the EU project TAILSAFE Contract nº EVG1-CT-2002-0066 and the NKFP 3A/068/2004 Hungarian fund extensive research has been carried out about paste technology. Different test methods and materials were applied. Tested tailings materials were as follows: different fly ashes from coal power plants from Pécs ? Hungary, Gyöngyös ? Hungary, Neyvil ? India, different Croatian ashes, hazardous waste incineration plant ashes from Dorog ? Hungary, different kind of sands from Hungary, fine glass sand from Fehérvárcsúrgó ? Hungary, flotation ore processing tailing from Gyöngyösoroszi ? Hungary. Different additives, as gypsum, bentonite and cement were tested as well. The applied test methods were as follows: physical material testing (laser sizer, piknometer, different microscopes), X-ray diffraction analysis, settling columns, the three measuring pipes tube viscometer (16~27 mm pipe diameter), a hydraulic test loop with different pumps (40~53 mm pipe diameter, 0.2~4 m/s average slurry velocity range, 0%~52 % volumetric concentration range), rotational viscometer, Cassagrande yield locus tester and the slump cone test. This paper summarizes and systematizes the results of the aforementioned research as well as reports about the developed paste pipe transport design method based on the fine suspension ? coarse mixture model. The paper also reports about a systematic experimental series with different materials to establish criteria when high concentration suspensions behave like paste.

Jan 1, 2014

By T. M. Yegulalp

A numerical model is being developed to assess the enhancement of permeability by improved fracture connectivity by micro-hydrofracturing. A generic two-dimensional percolation model has been developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park Mine has been used to establish statistical properties of the observed fracture systems. Results of statistical anlyses of the field data and examples of the use of percolation model are presented.

Jan 1, 1995

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By M. Misra

It is estimated that the volume of low -level and intermediate level contaminants present in the soil at different DOE sites is of the order of several million cubic feet. The existing remediation scheme is containerization followed by burial in Land Disposal Facilities (LDF's) which is economically unattractive warranting the need to develop alternate remediation routes. One such route is the physical separation based volume reduction approach to removing a MINIMUM AMOUNT OF CLEAN SOIL with the radioactive particles, reducing the amount of material that requires disposal. The purpose of this study was to evaluate and test the feasibility of using physical beneficiation techniques for removal of contaminants from soil. The performance criterion was to recover at least 80% of the activity in 20% or less of the original contaminated soil volume. Four different radioactively contaminated (primarily uranium and plutonium) soils from DoE sites namely LANL, INEL, Fernald Plant 1 Storage Pad (ID-B) and Mound soils were tested using gravity, magnetic, gravo-magnetic, hydrocyclonic and flotation devices. The paper is divided into the two sections. The first section presents the overview of the Heavy Metals in Contaminated Soil Treatability Project conducted at the University of Nevada, Reno (UNR) describing the salient features of a state-of-the art Soil Washing Laboratory and the technology equipments used in the test program. The second section describes the soil characterization and typical volume reduction results obtained from the UNR tests. Among the physical separation processes, only flotation processes passed the performance criterion. For the LANL and INEL soils where the contamination was contained in coarse particle size, it was possible to recover more than 80% of the activity in less than 10-20% of the original volume of the soil thus rendering 80-90% of the soil "clean". For Fernald and Mound soils where contamination was of colloidal nature, flotation based processes showed encouraging results and are recommended for further studies.

Jan 1, 1995

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By M. K. McCarter

INTRODUCTION Mining activity and basic geometry of open pit mines represent major obstacles in geotechnical mapping. Mining creates a constantly changing topographic base which may require corresponding updates of field sheets before mapping can proceed. The rapid pace of mining operations may also threaten removal of important geologic and engineering features before adequate base maps and surveyed control can be established. Maintaining such control during the mapping process is yet another complication. In addition, basic geometry yields nearly vertical outcrops. Access required for direct observation and measurement, essential to conventional plane table or Brunton techniques, may be impossible on such surfaces. Also, nearly vertical surfaces appear fore- shortened in plan view. This reduction in area provides little room for recording geotechnical detail. The difficulties encountered in open pit mapping can be substantially reduced by utilizing a modified form of plane table photogrammetry. This technique employs photographs taken from the ground as the base upon which details are recorded. The information is later transferred to plan maps using the plane table principal of location by intersection (Davis and Foote, 1953). Any change in topography can be accommodated by simply taking additional photographs. Proper spatial representation in plan view can be determined later when updated maps and surveyed control are available. In addition, horizontal photographs from the ground portray vertical surfaces as they are normally viewed thus providing maximum area for recording details. Any detail which can be identified on the photograph can be located correctly even though the actual feature is physically inaccessible. The technique presented in this paper was developed by the author for special applications at Kennecott's Bingham operation in 1970. The procedure was rapidly adopted for general use and has proven to be a practical tool for detailed investigation of potentially unstable areas (Zavodni and McCarter, 1976) and routine geological mapping (Richardson, 1975). Major advantages, other than those mentioned above, include: The speed and accuracy are greater than for conventional plane table or Brunton methods. The photo- graph represents a view from a station at some distance from the area being mapped. This vantage point allows evaluation of possible continuity of structures from one level to another which may not be evident at close range. The photographic base provides a permanent record of the topography at the time

Jan 1, 1977

By Patrick R. Taylor

Thermal plasma technology has a wide range of applications in extractive and process metallurgy. Beneficiation of complex ores, oxide reduction, melting/remelting of refractory metals and scrap, and the recovery of precious metals from waste products are some examples of potential uses for plasma technology. The highly concentrated enthalpy provided by plasma torches is a cleaner energy source and may give higher processing rates per reactor volume than conventional technologies. Some of the other advantages may be: controlled furnace atmosphere, ability to treat fine feed materials and rapid quenching. A review of some of the uses for plasma processing in non-ferrous process and extractive metallurgy is presented.

Jan 1, 1993