Search Documents

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By Jeremiah Cohn, Rachel L. Bauer, Catherine E. Johnson

Water is frequently used in explosive applications to increase explosive performance and reduce air overpressure. Water tamping can enhance cutting abilities of shaped charges in demolition and increase impulse of kicking or breaching charges. In explosive disposal, water is used to suppress air overpressure and reduce noise. Despite its widespread use, the specific effect of water placement, whether in front of or behind the explosive, has not been studied. This work evaluates the directional effects of water placement on blast performance using 400-gram sheet explosive charges in five configurations: no water (control), rear-only water (tamped), front-only water (pushed), water on both sides (confined), and a thin front-and-rear water layer (low mass confined) to assess reduced mass effects. Water was sealed in plastic bags and held in position with custom 3D-printed cages to ensure consistent geometry and contact. A modified ballistic pendulum consisting of a hanging steel W-beam was used to evaluate impulse transfer, with high-speed video capturing swing velocity. Air overpressure was recorded using a seismograph microphone. Rear-only water (tamping) increased beam swing velocity by 69% over the control while confinement with water on both sides increased performance by 12% at a 2:1 water-to-explosive ratio and by 50% at 4:1, though it still underperformed the tamped-only configuration. Pushed water alone did not increase beam momentum and reduced tamping effectiveness by 19% when combined. Seismograph microphone data showed that pushed and low mass confined water configurations produced some of the highest air overpressure levels (up to 139.2 dB), while tamped and control charges produced lower levels (~134–136 dB), suggesting that pushed water may amplify, rather than mitigate, air shock transmission. These findings show that water placement has a strong directional influence on blast dynamics: water behind a charge enhances energy transfer to the target, while water in front provides limited or potentially counterproductive mitigation. This study advances understanding of water–explosive interactions and will lead to more effective charge designs for breaching, disposal, and demolition.

Jan 26, 2026

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By M. Fener, S. Kahraman, O. Gunaydin, M. Alber

Falling into the weak rocks category, fault breccias have extremely poor engineering properties. These pebbles typically cause issues with slopes, subterranean construction, and building projects. Professionals will benefit from the creation of some predictive models for fault breccia triaxial strength, as smooth specimen preparation is typically challenging and timeconsuming. The purpose of this study is to develop some predictive models for the differential stress (Δσ) based on physical and textural properties. Artificial neural networks were used to analyse data related to Misis fault breccia. Initially, models with moderate (noticeable, but not good) correlation coefficients were created using multiple regression analysis. After that, the regression models and three distinct artificial neuron network models were contrasted. Regression models are weaker and less trustworthy than artificial neuron network models, as demonstrated by this comparison. Pointed out is the practicality and ease of use of the artificial neuron network model with S-wave velocity and volumetric block proportion. Ultimately, it can be concluded that artificial neuron networks analysis provides a reliable indirect method for predicting the differential stress of Misis fault breccia.

Sep 1, 2025

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance within the system is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation. Upgrades to the primary ventilation system are often required. The use of booster fans underground is a potentially practical alternative to the addition of shafts and surface fans. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room-and-pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By C. Dorfling, M. Tadie, S. Grobbelaar

The physicochemical properties of the complex electrolytes used in direct copper electrowinning are an important consideration for the development of a high-fidelity model of the process. Direct electrowinning electrolytes typically contain a high background of metallic impurities. The effect of metallic ions on the properties and accompanying change in the limiting-current density for copper reduction have been the subject of several studies. Although various empirical correlations have been published for describing the physicochemical properties of electrowinning electrolytes, the correlations are only applicable to a limited range of conditions and cannot be extrapolated without further validation. Consequently, in this paper we validated existing physicochemical property correlations for the full range of operating conditions applicable to direct copper electrowinning and developed a new correlation for predicting the associated limitingcurrent density for copper deposition. Following, we evaluated the benefit of using the validated correlations as a component of a dynamic electrowinning model.

Jan 1, 2023

By Dalton Fowler

"Pressure vessels used in pressure leaching and pressure oxidation processes in the mining industry are often lined with acid resistant brick and membrane systems. Although the options available when it comes to selecting materials and linings designs for these vessels appear somewhat limited there are, nevertheless? several choices which must be made in order to successfully design, manufacture and construct these linings. These choices require careful evaluation of materials properties which include, among others, thermal conductivity, thermal expansion, chemical swell, and modulus of elasticity, as well as a variety of construction methods.Some of the options available, and some of the means of evaluating them objective of this discussion."

Jan 1, 1999

By J. B. Boisvert, P. Oshust

A significant source of uncertainty in the diamond resource contained in kimberlite pipes is the volume of the pipes. Often the material within a pipe will be mined as ore, leaving the actual geometry of the pipe as a significant source of uncertainty. It is desirable to use stochastic techniques, rather than deterministic methods, to model pipe geometry because stochastic techniques generate multiple realizations that are reproducible and can be used to assess uncertainty in pipe geometry. The proposed methodology uses sequential Gaussian simulation of pierce point locations interpreted from drillholes through a kimberlite pipe. Kimberlite pipes are approximately cylindrical in shape; therefore, the data are transformed to cylindrical coordinates to facilitate the simulation of pipe geometry. Rather than using xyz coordinates to define the pierce points, z, ??and pipe radius are used. The radius variable can be simulated in z-??space to generate multiple realizations of pipe volume. Uncertainty in the volume of the pipe can then be evaluated. This methodology is demonstrated with a kimberlite pipe at BHP Billiton’s Ekati diamond mine.

Jan 1, 2008

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Jan 1, 1997

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of 12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Feb 24, 1997

By T. Stack, C. Roos, M. Drake, P. Conrad

"This paper presents the evaluation Montana Tech completed for the Western Energy Company Rosebud Mine relating to the benefits of survey data collected using novel technologies over traditional methods for topographic surveys. These technologies include Unmanned Aircraft Systems (UAS), photogrammetry, and laser scanning/LIDAR. Utilizing these technologies, large areas such as reclamation areas and cast blasts can be surveyed in a timely manner for use by the mining operation. The areas that were evaluated were the improvements in the safety of employees and the time required to collect data. In addition, there is also a potential cost savings for the operation, all while not affecting the accuracy of the data that is collected. PROJECT BACKGROUND Accurate topographic survey data is critical to successful surface mining operations. It is used for mine planning and design as well as permit compliance. Currently, employees typically collect survey data using GPS equipment or total stations. These methods can be dangerous, as they require employees to work near large operating mobile equipment, edge of high walls, and on piles of stacked steep-sloped loose material. Aerial and satellite photographs, performed by a contractor, can be used to obtain some of this information, but it is expensive and may not be attainable during overcast conditions. Montana Tech, along with the Rosebud Mine, conducted research on the accuracy, cost, and other benefits of survey data collected using novel technologies. Some of the methods studied include, but are not limited to, Unmanned Aerial Systems (UAS) or Vehicles (UAV), photogrammetry, and laser scanning. These methods were evaluated to determine if these technologies provide mining companies with a safer, cost effective, and accurate method to collect data for surface mining operations. The project scope was to evaluate various surveying techniques to determine which techniques would be applicable for the Rosebud Mine and complete a trade-off study comparing the new techniques with currently used methods. The trade-off study included an analysis of the technological differences between the methods, safety and legal considerations for the new techniques, operational limits, and the costs associated with each technique. Working with the Rosebud Mine team, techniques were selected for field trial and accuracy comparison. This paper presents a literature review of applicable technical papers and a summary of the Federal Aviation Administration regulations for UAS, followed by a study comparing conventional GPS topographic surveys with UAS based systems and laser scanning systems. The comparison of the various methods was broken into the following four categories: operator safety analysis, time comparison, survey accuracy, and cost analysis. After all of these portions of comparison were completed a recommendation was provided based on the evaluation that was performed."

Jan 1, 2017

By J. R. Campbell

It is the purpose of this paper to review somewhat in detail the literature on the subject that is extant, which ought to provoke considerable beneficial discussion. The value of 1 per cent. ash in blast-furnace practice was brought to the attention of the writer when he was connected with the U. S. Steel Corpn. Various groups of blast furnaces in the Pittsburgh district compiled a statement in which the average saving was about 6 c. per ton on pig iron for every 1 per cent. of ash reduction. Later, the same groups of furnaces, when materials had reached a higher price, compiled a statement in which there was a 30-cent saving on pig iron for every 4 per cent. ash reduction in the Pittsburgh district, which was equivalent to 7½ c. for every 1 per cent. ash reduction. In the Chicago district, on long freight hauls of coal and coke from the Pocahontas district, the set-up was 30 c. per ton of pig iron for every 2 per cent. ash reduction, or 15 c. for every 1 per cent. Some years ago, Ralph H. Sweetser, of the American Rolling Mill Co., presented a paper which provoked considerable comment.' To get the matter again before this body a résumé of his computations is given below: Comparison of Pig Iron Costs Ash in Coal. Ash in CoKe, Fixed Carbon in Coke peR Ton OB PIG Iron peN Day, Per Cent. PeR CeNt. Coke. Per Cent. PIG IRon. Lb. Tons 6.00 8.70 89.80 1800 365.0 7.00 10.15 88.35 1860 353.2 Coke with 8.70 Per Cent. Ash Ore mixture, 4144 It). = 1.85 tons @ $5.50.............................. $10.17 Coke, 1800 lb. = 0.90 ton @ $6.50..................................... 5.85 Limestone, 1000 lb. = 0.50 ton @ $1.50................................. 0.75 Labor, $365 per day on 365 tons....................................... 1.00 Supplies and service, $250 per day...................................... 0.68 Overhead, $200 per day............................................... 0.55 Reserve for relining and depreciation................................... 1.00 Total............................................................. $20.00

Jan 1, 1931

By L. M. Chan, D. H. Carlson, J. H. Johnson

"This paper discusses the evaluation and application of a portable parked-vehicle tailpipe emissions measurement apparatus (EMA). The EMA consists of an exhaust dilution system and a portable instrument package. The EMA instantaneously dilutes and cools a sample of exhaust with compressed nitrogen or air at a known dilution ratio, thereby presenting it to instruments as it is presented to personnel in the surrounding environment. The operating principles and governing equations of the EMA are presented.A computational method is presented to determine the engine operating and performance parameters from the exhaust CO2 concentrations along with an assumed engine overall volumetric efficiency and brake specific fuel consumption. The parameters determined are fuel / air ratio, mass flow rates of fuel, air and exhaust emissions, and engine brake torque and horsepower. These calculated engine parameters are used to characterize engine load when performing EMA in-field tailpipe sampling without a dynamometer, and to detect deteriorated engines.Evaluations of the EMA by comparison of diesel tailpipe measurements with those made using laboratory-grade instruments showed that the EMA measurements are accurate and reproducible. The results also show that the EMA is capable of detecting emission concentration changes resulting from engine faults. Calculated engine operating and performance parameters correlate and compare well with laboratory-measured values.The EMA in-field engine loading and tailpipe sampling procedures for parked vehicles are presented, and results of the EMA field measurements are also presented. Low coefficients of variation for repeat EMA tailpipe measurements on diesel-powered haulage vehicles in four underground mines indicate that the EMA in-field engine loading and tailpipe sampling procedures are reproducible.An analysis of EMA tailpipe measurements for three haulage vehicles in one mine shows that the EMA can: 1) identify haulage vehicles that emit excessively high pollutant concentrations, and 2) provide data needed to evaluate and determine the efficiency and effectiveness of tailpipe emission control devices.Finally, recommendations for a proposed commercial EMA system are presented. This commercial system would overcome many of the adverse features of the prototype EMA used in these tests."

Mar 1, 1992

By Mehmet Mesutoglu, Ihsan Ozkan

This study investigates the feasibility of rock bolting support in an underground coal mine gallery with a thick coal seam. The Ömerler underground coal mine working area, owned by West Lignite Enterprise of Turkish Coal Enterprises, was selected for this purpose. Longwall top coal caving is implemented as the production method in the Ömerler underground coal mine. Field and laboratory studies were conducted to determine rock mass and rock material properties, followed by experimental, empirical and numerical analyses based on the acquired data. The obtained design results were evaluated using a resin-grouted rebar rock bolting (RBR) system and steel arch support (SAS) pilot application areas. The numerical modeling results conducted using the fast Lagrangian analysis of the Continua 3D (FLAC 3D v6.0) program indicated less displacement and secondary stress change in the RBR-supported zone compared to the SAS-supported zone. In situ measurements also demonstrated that RBR provided more successful support to the roof during coal production activities. The findings suggest that RBR is a more effective solution when evaluating the feasibility of rock bolting support systems in underground galleries with thick coal seams at the Ömerler Mine. This study emphasizes the importance of more sustainable and safe support systems to enhance operational efficiency in the coal mining industry.

Mar 1, 2025

By Stan Tang, Yiming Sun, S. Amir Reza Beyabanaki, N. Sathi Sathialingam

The Kurve mixed-use development project including a 22-story tower at 2801 Sunset Place was constructed on a site consisting of a roughly rectangular-shaped lot at the intersection of Wilshire Boulevard and Hoover Street in Los Angeles. Two Metro Red Line tunnels, with depths of approximately 30 feet and 58 feet, respectively, cross below the building at distances of approximately 1 foot to over 63 feet from the site. This paper presents numerical modeling performed to evaluate the ground and tunnel behavior in response to building construction. Results of geotechnical instrumentation and monitoring undertaken during the building construction are also discussed.

Jun 13, 2023

By Robert A. Pimentel

Dust is still a major problem in increasing production from longwall faces. Over the last decade, significant improvements have been made in the development of techniques for reducing dust exposure on conventional and continuous sections. But virtually no improvements have been made in dust control on longwall sections. It is true, that there are many more continuous mining sections than longwall sections in the United States and that the number of workers overexposed on continuous miner sections is much larger than the number on longwall sections. However, the problem on continuous miner sections appears much easier to solve and, in fact, we believe that the techniques are available to get virtually all continuous miner sections in compliance. The problems on longwall sections are much more elusive. Also, the number of longwall sections in the United States is expected to increase during the 1980's. Thus, dust control on longwall sections remains a formidable and important problem. Companies operating longwall sections with a dust problem are faced with the tasks of having to quantify the various dust sources, of selecting proper techniques to reduce the problem, of implementing the techniques and of evaluating their effectiveness.

Jan 1, 1983

By D. W. Hayley

The rapid expansion of exploration drilling with anticipated production facilities for oil and gas in the Mackenzie Delta region of the Northwest Territories has created a demand for granular construction materials. This paper discusses the technique adopted and experience gained by the authors from several major resource evaluation programs in this remote area. The first part of the paper describes a methodology for deposit identification, logistics of helicopter and ground-based drilling operations and the sampling difficulties which are unique to permafrost: soils. The second part describes the exploitation of a large glaciofluvial deposit at YaYa Lake on Richards Island. Granular construction material is sparse in the delta region relative to projected demand. Exploitable sources of granular materials for aggregates or construction borrow are found in glaciofluvial deposits of Pleistocene age or in outcrops of Paleozoic bedrock. Glaciofluvial landforms can be located by reference to published surficial geology maps coupled with airphoto interpretation. Preliminary assessment of these features in a large region is most economically carried out during the summer months with a drill that is transportable by helicopter. Once prospective borrow pit sites are identified, a detailed ground-based winter drilling program must be undertaken to establish aggregate quality and quantity, and to provide information on natural features which could affect development. The glaciofluvial terrain has been highly modified by the formation of massive ground ice within the gravel deposits. This presents some unique pit development problems which are not encountered in a normal bedrock quarry operation.

Jan 1, 1977

By R. C. Ford, J. Kelsey, S. A. Pierce, M. D. Ankeny

Evaluation of acid drainage risk from spent (leached) ore in arid climatic zones consists of two components: (1) whether residual and secondary minerals will release acid and metals when exposed to rainfall, and (2) whether ambient rainfall is likely to infiltrate, and eventually impact surface or ground water resources. The risk of acid drainage from spent ore at the El Abra on-off copper leach pad operation was evaluated using conventional geochemical methods and unsaturated flow models. Although geochemical testing indicated poor quality water would result from any seepage, unsaturated flow modeling demonstrated that infiltration and seepage were unlikely given the arid climatic conditions. Modeling further demonstrated that the residual moisture content of the spent ore when it is removed from the leach pad controls the risk of seepage. To further reduce the risk of seepage, operational controls were developed and implemented at the El Abra site.

Jan 1, 2000

By Judson H. Whitman

To evaluate intelligently and to market a source of rare earth raw material, it is necessary that the producer understand the requirements of the processor and the manner in which these requirements effect the value and salability of his product. This paper will be an attempt to aid in such an understanding. The majority of rare earth processors are primarily chemical companies, not mining or metallurgical companies, as the complexities of the processing procedures are' much more chemical in nature than metallurgical. The rare earths and the rare earth industry are normally divided into two groups - the ?light? or cerium group and the ?heavy? or yttrium group. They are so named because cerium and yttrium are the most common elements in 'heir respective groups and are so divided on the basis of mineralogical and chemical characteristics. The dividing line of the two groups is not rigidly fixed but usually is considered as being between samarium (atomic number 62) and europium (atomic number 63). Although the two groups are quite similar, processing procedures differ significantly, hence most processors tend to specialize in one group or the other. There is, however, a growing tendency toward participation in both groups.

Jan 1, 1960