Search Documents

By C. Bise, A. Seal

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during both the mid-1970s and the mid-1990s consistently show that hearing hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When MSHA’s new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to re-evaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Penn State research project currently being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels, and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2001

By G. F. Revey

All underground operations have limiting factors that influence overall profitability. Hoisting, hauling, available headings, labor, milling capacity and other factors limit how much material can be removed from an underground mine. Consequently, when mines use limited labor to handle the additional rock from overbreak and to perform extra ground support tasks, productive activity is replaced by non-productive work. Mining economics are further penalized when overbreak causes dilution of ore grades. This paper reviews organizational systems that mines have used to create environments which foster the creation of successful overbreak control programs. Actual case histories document the various quality improvement techniques, worker incentives, and practical project management systems used by these mines. A brief review of controlled blasting technology sources and overbreak measurement tools is also included.

Jan 1, 1997

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

By Feida Wu, Yuhang Liu, Huimin Gao, Yuhan Song, Zhi Liu, Zijie Ren

In the process of quartz purification by calcination water quenching, the different expansion rates of gangue minerals and quartz were used to produce cracks or remove fluid inclusions, which is conducive to subsequent purification. However, the role and mechanism of calcination-water quenching are still lacking in research. In this paper, the position of calcinationwater quenching in gangue quartz purification process was adjusted and the removal effect of calcination-water quenching process at different nodes in the process was explored. The results show that the purification effects of grinding-calcinationwater quenching-classification-acid leaching process and grinding-classification-acid leaching-calcination-water quenching process were relatively good. The main reason is that calcined water quenching can make quartz produce cracks, which are more rough. At the same time, calcined water quenching is located after grinding, which has a larger specific surface area, pore volume and pore diameter, and has a strong adsorption capacity for acid solutions.

Nov 2, 2023

By Bin Xu, Qian Li, Ya-xuan Wang, Yong-bin Yang, Xi Zhang, Tao Jiang

The effects of common associated sulfide minerals including pyrite, arsenopyrite, galena and sphalerite on thiosulfate leaching of gold were studied in this work. Sulfide minerals had significant effects on gold leaching because that the dissolved products of sulfide minerals precipitated on gold surface to form coating layer. The degree of sulfide minerals impact on gold dissolution decreased in the order of pyrite ≈ galena > arsenopyrite > sphalerite, while the degree of effects on thiosulfate consumption decreased in the order of pyrite > arsenopyrite > sphalerite > galena. The additive CMC (Carboxymethyl cellulose) could not only reduce thiosulfate consumption but also increase gold dissolution. The mechanism of this might be that CMC could restrict the decomposition of thiosulfate by cupric ions and the precipitates on gold surface.

Jan 1, 2015

This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified.

Jan 1, 1986

Further evidence is presented as to the widespread occurrence of Thiobacillus ferrooxidans in nature in association with sulphide minerals. Leaching rates are discussed in terms of the effect of environmental parameters, particularly Eh and pH, on the bacterial process.The methods used to investigate leaching phenomena are described and the advantages and limitations of each method are discussed. A theoretical treatment of the bacterial leaching process is given which indicates that the optimum conditions arrived at by traditional methods are compatible with those deduced from consideration of the mathematics of continuous culture and thermodynamics

Jan 1, 1968

By Tao Zhang, Wen-tao YU, Hai-bin ZUO, Jian-Liang Zhang

Sintering-pot tests and metallurgical performances of sinter with 4 kind of different Al2O3 contents are experimented in this paper. Results show: when the Al2O3 contents increase from 2.0% to 3.5%, acicular calcium ferrites in mine phase will be gradually replaced by plate-like iron calcium. The increase of Al2O3 contents will lead to the addition of liquid viscosity and the reduction of permeability of sinter bed. Sintering time will be prolonged. The rate of yield is stable basically but production is low; besides, the increase of liquid viscosity will decrease of drum strength. The change of permeability of the material layer will make RDI +3.15 decrease first and then increase when Al2O3 contents changed from 2.0% to 3.5%. RI of sinter shows a contrary trend because many open voids are formed by deterioration of liquidity first and then pores closed.

Jan 1, 2015

By Mark McComb, Geoffrey R. Lane

"Over the years many differing approaches have been developed to clearly understand the nature, mode of occurrence, associations and deportment of both free-milling and refractory gold in a wide variety of differing geologic environments and plant products. Many approaches can be taken to characterize the ore which may occur as complex fine grained gold, ultra-fine grained gold, coarse nuggetty gold, complex Asrich refractory gold and double-refractory gold. The approach taken in assessing small drill core composites from Novo Resources Beaton Creek Paleoplacer gold project located in the Pilbara region of Australia was complicated by the nature of the ore, the small amount of sample available from current exploration work, and the gold grade and the grain size distribution. In this case the scope of the study was limited by sample availability although significant amounts of valuable information was also gained. This gold characterization study included the following elements:??Size fraction assays??Ore microscopy??Preparation of heavy mineral concentrates from sized fractions (screening) of crushed or milled head using heavy liquids and Superpan table.??Systematic scans of the heavy mineral concentrate, middling, and tailing fractions using TIMA Automated Scanning Electron Microscopy integrated with an Energy Dispersive Spectrometry to provide semi-quantitative elemental analysis of the individual grains found in the sample.The unique methodology employed to detail the gold deportment was the combination of the Tescan Integrated Mineral Analyser (TIMA) and the Oxford INCA GSR software. This technique not only allowed us to document the deportment of gold but recognize other associated minerals, which included gersdorffite, chalcopyrite, uraninite, coffinite, brannerite and several Rare Earth-bearing minerals.INTRODUCTIONGold deportment studies are commonly carried out on preliminary gold exploration projects in order to determine the various limitations, which may effect processing of the potential ore. This is often because it may be expected that there may be a refractory component to the gold, which may limit physical separation techniques and suggest more costly hydrometallurgical techniques. Often when carrying out gold deportment studies the mineralogical methods may be limited to assuming that the gold will be fine and easily found using standard techniques of optical microscopy or Scanning Electron Microscopy. This may not always be the case as various geological environments may pose their own individual problems to determining the deportment of the gold grains."

Jan 1, 2015

By P. Amelunxen

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan?s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By Aleksandar N. Nikoloski, Rorie Gilligan

Brannerite, UTi2O6, is the most common of the refractory uranium minerals and requires leaching under intense conditions to effectively extract the uranium contained within. Brannerite is often found together with apatite in metasomatic uranium deposits. Apatite and other phosphate gangue minerals can inhibit uranium leaching by generating phosphate ions which interfere with the reactions between acidic ferric sulphate and uranium minerals. As part of a detailed fundamental study on the leaching reaction mechanisms for brannerite, tests under a range of selected leach conditions were carried out with the addition of 10 g/L fluorapatite with the goal of identifying conditions where the negative effects of phosphate are reduced. Leaching was carried out for 5 hours with 0.05 mol/L Fe3+ as Fe2(SO4)3 with 0.25–1.00 mol/L H2SO4 and at temperatures between 25 and 96 °C. A single test was performed with 0.05 mol/L Fe3+ as FeCl3 and 1.00 mol/L HCl. In the sulphate system, the effect of phosphate was weakest at the highest acid concentration (1.00 mol/L H2SO4). In the chloride system, phosphate did not suppress uranium extraction, suggesting that HCl leaching could be a viable alternative for the leaching of high-phosphate refractory uranium ores.

Mar 17, 2021

By Stephen Tadolini

The annulus thickness, for bolts anchored with resin, effects the systems final performance. Recent developments in the manufacturing process of these support systems, coupled with improved resin characteristics, have resulted in design changes to minimize hole drilling requirements and reduce resin usage. The amount of resin to properly anchor a 7/8-SRD (Special Rolled Dimensions) bolt in a 25.4 mm (1-in) diameter hole has been reduced to about one-third of the resin required to anchor a No. 7 rebar bolt (22 mm (7/8-in) diameter) traditionally installed in a 35 mm (1-3/8-in) diameter borehole. More importantly, laboratory and field tests, indicate that higher bond strengths and anchorage capacities can be realized with reduced annulus systems. These factors have a direct bearing on reinforcement efficiency and subsequent roof support performance.

Jan 1, 1998

By Joseph Nawrocki, Margaret Hettinger, Dr. Catherine Johnson

"Optimized rock fragmentation is essential for minimizing downstream costs to mining operations.Photographic fragmentation analysis, vibration monitoring, and high-speed video all providemeasurements of blast effectiveness and supply data that allows operations to modify blasts to achieve downstream goals."

Jan 1, 2016

By Neal Lee

Often the effects of wet boreholes are not taken into consideration when designing a blasting program to exhibit a certain amount of explosive energy per unit of rock such as design by powder factor, expressed in lbs./bcy (pounds explosives per bank cubic yard) or kg/bcm (kilograms per cubic meter), often the effects of wet holes are not considered. This paper examines different methods of loading wet holes and the effects they have on actual explosive quantities/unit of rock. In particular, we are looking at the amount of water trapped within the explosive column (bulk loading from the collar), or the annular space left void of explosives product around and between cartridges (wet-bags) with many of the current wet hole loading methods in use. We will focus on the effect this has on actual powder factor relative to “as designed” dry hole loading values, as well as the effect on performance of the explosives.

Jan 1, 2011

By L. D. Patts, J. D. Noll, S. E. Mischler, G. H. Schnakenberg

In this study, we evaluated the ambient diesel particulate matter (DPM) concentrations (at the intakes and exhausts of the mine) as the entire vehicle fleet of a stone mine switched from using 35% biodiesel to using a water emulsified fuel (PuriNOx). Elemental carbon (EC) was reduced by 45% when a PuriNOx blend containing 10% water replaced 35% biodiesel and by 57% when a PuriNOx blend containing 20% water was used. Other factors such as engine duty cycle and production changes could potentially cause some day-to-day EC fluctuations, and no direct comparison to commonly used dieselfuels (No. 1 or No. 2) was achieved. Therefore, a second study was performed in a controlled “isolatedzone” environment to fametal mine, comparing PuriNOxto No.1 diesel fuel in a load haul dump vehicle. The EC fraction of the DPM was reduced by about 71% when the PuriNOx blend containing 10% water was used and by about 85% when the PuriNOx blend containing 20% water was employed. This study did not determine how the water emulsified fuel would affect the engine or power.

By C. M. Offenhauer

Abstract Zirconium markedly affects the formation of graphite in cast iron and may promote the formation of normal flake gaphite, fine flakes of eutectiform graphite, or spheroid nodular graphite, according to the composition of the Iron and the amount of the zirconium addition. Usually, it is employed in the form of a complex addition agent in order to facilitate its introduction and to guide its effect. The reported applications of zirconium as an inoculant for the production of pearlitic high-strength cast iron indicates that it is most effective as a silicon-manganese-zirconium alloy. Added in this form it reduces chill and minimizes zones of ferrite and eutectiform graphite. In low-sulphur cast iron, zirconium in amounts greater than 0.10 per cent tends to promote the development of eutectiform graphite. These irons are characterized by freedom from primary cementite or normal flake graphite and exhibit very little tendency to shrinkage on solidification. In hyper-eutectic low-sulphur cast iron, zirconium causes the formation of a partially nodular graphite structure. A combination of magnesium with silicon-zirconium alloy was found to produce completely nodular graphite structures without the hazards associated with the addition of elemental magnesium.

Jan 1, 1949

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By W. J. Cherones

This paper describes the history of the development and application of the electric mining shovel in open-pit mining, dea1ing particularly with far-reaching advancements in three primary areas: metallurgy, mechanical design and electrical systems. Hoist drives and crowd drives, including the Magnetorque and Electrotorque systems, and the integral propel drive are given close attention.

Jan 1, 1972

The dissolution behavior of gold and silver from Au/Ag alloys in aerated cyanide solutions has been investigated using rotating disc electrodes. The variables studied included concentration of cyanide, oxygen partial pressure and rotating speed of the disc. The dissolution potential and the rate of dissolution were obtained in view of the anodic and cathodic current-potential relationships. The results were discussed in terms of a mixed potential theory. The results showed that the dissolution rate of gold and silver from the alloys was partially controlled by chemical reaction, but largely by transport of either oxygen or cyanide, depending on their relative concentration under the experimental conditions employed in this study.

Jan 1, 1995

Power Plant. The power for the metallurgical operations is supplied by the company's own power plant, which is centrally situated. Power is also supplied to Metal Manufactures Ltd. and Australian Fertilizers Ltd., both being adjacently situated to this company'sworks.The power supplied is direct current, 250 volts, and is obtained from direct-current generators coupled to turbines and to Belliss & Morcom triple expansion engines.The steam supply is obtained from Babcock & Wilcox water tubular boilers, the fuel used being drawn from the South Coast coal mines.Transport. - The works are connected by standard broad gauge railway to both the jetties and the Government railway. Two steam and three electric locomotives are employed in this service.In addition to its own requirements, transport is provided to Metal Manufactures Ltd. and Australian Fertilizers Ltd.The various operating departments are connected by a 2-ft. gauge railway operated by Jeffrey electric locomotives.Ore Storage and Sample Mill - These departments are connected by broad gauge line to the Government railway and jetties. All material which is railed or shipped to the works from the various centres is weighed, sampled and placed in the ore store, or outside gantries, before being treated.Since the whole of the material received is either purchased or treated on a toll charge, great care is necessary in the weighing and sampling of all the receipts.Assay Oflice--The assay office is divided into several laboratories, where analyses of the various purchased materials and works samples are carried out.

Jan 1, 1938