Search Documents

By Phil Rice, Mohammed Nasim, Richard Flanagan

"The Gateway Trans-Hudson Partnership (GTHP), a joint venture of WSP USA, Inc., AECOM USA, Inc, and STV Incorporated, is providing preliminary engineering services to Amtrak for the Hudson Tunnel project as well as supporting the NEPA process for getting the record of decision (ROD). This preliminary engineering design effort by GTHP includes geotechnical exploration and laboratory testing, design of structures, tunnel contract packaging and procurement planning.The Hudson Tunnel Project includes the construction of a new Hudson River Tunnel system and rehabilitation of the existing North River Tunnel. The new tunnel system will be constructed south of the existing North River Tunnel, from North Bergen under the Palisades to Hoboken in New Jersey, below the Hudson River, and connecting directly to Penn Station in New York (Fig. 1). The tunnel system is configured as two single-track tubes, intermediate ventilation shafts and cross passages in compliance with NFPA- 130 requirements. The adjacent surface alignment west of the Palisades will be constructed on viaducts, embankment and retained fills. The existing North River Tunnel (Fig. 2) consists of two single-track, electrified rail tunnels extending from tunnel portals in North Bergen, New Jersey to Penn Station in New York. Completed in 1910 by the Pennsylvania Railroad, the tunnel opened at the same time as Penn Station and the four, single-track, East River tunnels that connect Penn Station to Queens and onto Long Island and New England, respectively. Both tunnels in the existing North River Tunnel were inundated with brackish river water during Superstorm Sandy (Fig. 3), resulting in the cancellation of all Amtrak and NJ Transit service into New York City for five days. After the brackish water was removed from the tunnels, the residual chlorides and sulfates have had on-going detrimental impacts on the interior concrete and rail systems."

Sep 1, 2019

By Ben Hayes, Michael Ryjevski

The Palm Jumeirah is the smallest of the three Palm Islands (Palm Jumeirah, Palm Jebel Ali and Palm Deira). It is located on the Jumeirah coastal area of the emirate of Dubai, in the United Arab Emirates (UAE). The unique man made island is built in the shape of a date palm tree and consists of a trunk, a crown, 17 fronds and a surrounding crescent island that will form a breakwater. The Jumeirah Palm Island is primarily are treat and residential area for living, relaxation, and leisure. It will contain themed boutique hotels, three types of villas, shoreline apartment buildings, beaches, marinas, restaurants, cafes and a variety of retail outlets.

Jan 1, 2007

By John D. Smith, Robert J. Mitchell

"There is a world-wide trend toward underground bulk mining methods employing hydraulically placed backfill. This trend is recent and therefore there is little in the literature to assist an operator in the design of backfill properties, the design of drainage facilities, the calculation of the operating forces on a bulkhead, and the control procedures considered necessary before, during and after pouring. This paper presents recommended procedures that are based on over to years of experience in the various aspects of backfilling large openings. Free-draining timber or concrete block bulkheads are shown to be a viable alternative to massive reinforced concrete bulkheads for the containment of backfill pours. Hydrostatic pressures cannot develop in backfills provided adquate drainage facilities are installed.IntroductionThe increasingly adverse relationship between mining costs and mineral values has led mining companies to develop more productive, lower-cost, bulk mining methods. This has led to the increasing use of large, more or less continuous, hydraulically placed backfill pours to enable the recovery of a higher proportion of pillar ore. The success of any bulk mining method depends on the degree of stability maintained during the stoping operations with reference to the mining rate, the performance of the backfill with respect to the per cent extraction of pillar ore, and the control of the mine structure with respect to safety and productivity. One such method has been previously described(I) where a steeply dipping orebody is being mined with a sub-level method that employs large, hydraulically placed tailings pours for delayed pillar recovery. The paper describes the rock mechanics analysis undertaken to establish the stope and pillar geometry and the approach taken to establish backfill strength requirements to prevent dilution during pillar recovery. Production with this method started in 1970 and because few, if any, large bulk pours had previously been used in- this way (judging by the lack of information in the literature), design data and criteria were needed for several aspects of the work. Methods to establish backfill quantities and pertinent ""in-place"" fill properties are described in 2, 3 and 4 in the list of references. Results of field measurements taken to establish fill pressures for bulkhead design purposes are described in 5 and 6. Laboratory large-scale model tests undertaken to confirm a fill strength design equation, which takes into account fill arching, have recently been completed. A paper describing these tests and the results will be forthcoming in the near future."

Jan 1, 1982

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By Guilherme L. M. G. Carvalho, Zachary T. Fleming

In a world of 2-dimensional design documents, envisioning and understanding 3-dimensional interferences for complex foundation construction scenarios can be challenging. Videos and computer models serve as 3-dimensional spatial aids but have drawbacks related to a fixed perspective. Augmented and virtual reality (AR/VR) provide new tools to communicate design challenges and improve construction planning. This paper provides a practical look at the basics of AR/VR systems and the tools available to the foundation design and construction industry by giving a high-level example of the technologies’ use in the design and delivery phases of a complex micropile installation project for the remediation of a dam foundation. Using these technologies, GEI was able to design and deliver a complex foundation remediation solution. AR/VR benefited regulators, and the client, to help understand the design concept, construction sequencing, and approach to overcoming installation challenges. Due to its user-friendly nature and less rigorous programming and hardware requirements, AR proved to be more useful than VR for this scenario. AR/VR will likely not replace videos and computer models; however, it can be a useful 3-dimensional visualization aid that complements the project delivery process and offers benefits that traditional methods cannot. INTRODUCTION Augmented and virtual reality is a promising and rapidly developing technology within the engineering and construction world. Like any rapidly developing new technology, the language describing it can be confusing and dynamic. To eliminate the confusion some definitions must be made. AR/ VR definitions The definitions of virtual reality (VR) and augmented reality (AR) for the purposes of this paper are as follows: VR is a computer-generated immersive environment that the user experiences within a digital 3- dimensional space (Satava, 1993)AR is a composite view created by superimposing digital objects into the user’s real-world view (Azuma, 1997). Often, VR is used in an office environment and allows the user to “visit” the digital site to review site planning, construction sequences, and interference geometry. AR can be utilized in both the office and onsite environments. Like VR, the in-office application for AR is commonly site planning. AR also can be utilized in the field for applications such as seeing through the ground to locate known existing obstructions like utilities, gas tanks, etc.

Jan 1, 2019

By T. G. Mayhew, A. A. Bergeron, R. J. Mahany

This report describes an operational communications system which provides remote intra-terrestrial wireless transmission of environmental information. Design and modification specifications of requisite equipment are included along with a detailed description of system operation

Jan 9, 1976

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

A low noise blast hole drilling system was developed to limit the risk of noise induced hearing impairment in mining operations. Noise induced hearing loss has been identified as a major occupational health risk in SA mines. The noise generated by pneumatic percussion drills is a major contributor to such noise induced hearing. This motivated the South African Safety in Mines Research Advisory Committee (SIMRAC) to commission the development of a low noise rock drill system. The system had to be designed, manufactured, tested and demonstrated in a simulated underground mining environment. The specification required noise levels below 90 dBA. Other important design considerations were ease of manual transport, setting up and operation. The primary design concept was to encapsulate a standard Seco S215 pneumatic rock drill in a composite material tube. The tube is pushed onto the rock face by a pneumatic cylinder and is sealed at the rock face by an elastic seal. The drill is pulled towards the rock face by a rope and pulley mechanism fitted inside the tube. This mechanism is powered by a second pneumatic cylinder. The actions of moving and setting the drill require two persons. However, the team can carry out the drilling function itself on several drills simultaneously because of the self-thrusting design. The drill is supported by two camlocks. The exhaust (air containing dust, water, rock shavings, oil and grease) is removed from the encapsulating tubes via exhaust tube to the end of the stope. In this way exhaust noise and air pollutants are disposed of away from personnel. Tests were conducted in a test stope. Noise levels of under 90 dBA were achieved, thereby attaining the primary design specification. This was achieved without materially compromising ease of handling. Penetration rate was somewhat improved compared to that of the standard drill, so that productivity could be maintained. Keywords: Drill, rock drill, quiet, noise, mine, underground.

Jan 1, 2003

By N. D. L. Burger

A low noise blast hole drilling system was developed to limit the risk of noise-induced hearing impairment in mining operations. Noise- induced hearing loss has been identified as a major occupational health risk in SA mines. The noise generated by pneumatic percussion drills is a major contributor to such noise-induced hearing loss. This motivated the South African Safety in Mines Research Advisory Committee (SIMRAC) to commission the development of a low noise rock drill system. The system had to be designed, manufactured, tested and demonstrated in a simulated underground mining environment. The specification required noise levels below 90 dBA. Other important design considerations were ease of manual transport, setting up and operation. The primary design concept was to encapsulate a standard SecoS215 pneumatic rock drill in a composite material tube. The tube is pushed onto the rock face by a pneumatic cylinder and is sealed at the rock face by an elastic seal. The drill is pulled towards the rock face by a rope and pulley mechanism fitted inside the tube. This mechanism is powered by a second pneumatic cylinder. The actions of moving and setting the drill require two persons. However, the team can carry out the drilling function itself on several drills simultaneously because of the self-thrusting design. The drill is supported by two camlocks. The exhaust (air containing dust, water, rock debris, oil and grease) is removed from the encapsulating tubes via an exhaust tube to the end of the stope. In this way exhaust noise and air pollutants are disposed of away from personnel. Tests were conducted in a test stope. Noise levels of under 90 dBA were achieved, thereby attaining the primary design specification. This was achieved without materially compromising ease of handling. Penetration rate was somewhat improved compared to that of the standard drill, so that productivity could be maintained. Keywords: Drill, rock drill, quiet, noise, mine, underground.

Jan 1, 2004

By G. L. Dollinger, J. P. Kindsvater, J. A. Gibson

DESIGN AND DEVELOPMENT OF A MOBILE MINING MACHINE INTRODUCTION Until recently, developing tunnels in hard rock has been accomplished either by the drill and blast method or by using large tunnel boring machines. Combining the flexibility of drill and blast with the safety, efficiency and productivity of a TBM has been the objective of mining machinery producers for many years. In 1979 The Robbins Company began developing a new type of tunnel boring machine called the Mobile Miner to meet these objectives. The development and testing of the Mobile Miner is the subject of this paper. CURRENT MINE DEVELOPMENT METHODS Both the drill and blast method and the use of a TBM have notable advantages and disadvantages. The drill and blast method, for example, allows much more flexibility, requires less setup time and has a lower initial cost than a TBM; however it requires the use of high explosives and blasting has a disrupting effect on the rock surrounding the development. A TBM, on the other hand, is safer to operate, more efficient, more productive and produces smooth tunnel walls without disturbing the surrounding rock. In longer straight drifts it will easily out distance the drill and blast method. The TBM, however, is limited to boring a circular cross section tunnel which must then be modified if a flat floor is required. It also has a higher initial cost and an extended setup period.

Jan 1, 1985

By T. V. Nguyen

The feedwell performance in gravity thickeners and clarifiers relies on the efficient mixing between solid particles and flocculant to achieve effective flocculation, as well as energy dissipation of the incoming feed stream. A population balance-computational fluid dynamics (PB-CFD) model has been developed and validated to provide new insights into the operation and performance of industrial feedwells. In particular, the PB-CFD model enables the efficacy of the main functions of a feedwell to be investigated for a wide range of feedwell designs and process conditions. This paper describes how PB-CFD was used in the design and development of a new feedwell concept for the flocculation of particles in a solid-liquid stream. The patented feedwell design includes an upwardly converging flow diverter to create two separate compartments for energy dissipation and flocculation. PB-CFD simulations of this simple and easy-to-retrofit feedwell design illustrate a superior performance in terms of flocculation and energy dissipation compared to typical feedwells over a wide range of flow conditions. The potential benefits include reduced flocculant consumption, better de-aeration, greater stability and the ability to cope with a wider variation in volumetric throughput, better flocculation and fines capture, and a more symmetrical discharge that may also offer improved overflow clarity in some applications. The new feedwell design has been installed in a full-scale thickener at an Anglo American Platinum site in South Africa. A number of operational factors complicate this application, but indications are that the new feedwell has led to improvements in stability and underflow properties.

Jan 1, 2012

By B. S. Riess

A novel design for an automated uranium pellet stacking system is presented. This system is designed as a drop-in solution to the current production line to enhance the fuel pellet stacking process. The three main goals of this system are to reduce worker exposure to radiation to as low as reasonable achievable (ALARA), improve product quality, and increase productivity. The proposed system will reduce the potential for human error. This single automated system will replace the two existing pellet stacking stations while increasing the total output, eliminating pellet stacking as a bottleneck in the fuel bundle assembly process.

Aug 1, 2010

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By D. B. Apel

Rock mechanics software plays an important role during the design process of modern underground mines by allowing for verification of the stability of the planned excavations. The paper describes the methodology used to plan and locate the permanent underground openings at McArthur River Mine with the assistance of numerical modeling software.

Jan 1, 2004

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J. Moema, L. Mampuru, M. Phasha, D. Mkhonto

The global liquified natural gas (LNG) storage market size is projected to reach USD17.5 billion by 2025. Currently, owed to its high toughness, tensile strength, and excellent weldability, the 9% nickel steel is the most used in building infrastructure for cryogenic applications such as the construction of tanks and pipes for storage and transportation of LNG. However, this alloy is not readily available because of its complex production process and high cost. This provides an opportunity for suitable alternative materials to build infrastructure for cryogenic applications. Among strong contenders is the Fe-Mn based alloys, which have sparked global interest due to their desirable properties such as relatively lower density, low cost, high toughness and strength, due to a high manganese (Mn) content. These attractive properties render Fe-Mn based alloys preferred candidates to replace traditional steels in engineering applications in which strengthweight ratio is critical. In response, as a build-up to designing and developing austenitic Fe- Mn alloys, the present study employed density functional theory (DFT) based first-principles computational materials modelling technique to investigate the structural, thermodynamic, and magnetic properties of binary Fe-Mn alloy composition in competing FCC, HCP, and BCC crystal structures. Using this approach, it was possible to unravel the key underlying elastic properties that are directly correlated to experimental tensile strength and high toughness in binary Fe-Mn alloys. Besides successfully validating the existing experimental data, the current predicted properties and the deployed approach will serve as a benchmark from which further alloying required to improve other properties will be conducted.

Mar 4, 2025

By Pradip

Bastnaesite, a rare-earth fluocarbonate, was separated from associated calcite and barite gangue minerals in the Mountain Pass, CA rare-earth ore beneficiation plant by froth flotation using fatty acids (tall oil) collector, lignin sulfonate depressant and soda ash modifier after high-temperature (steam) conditioning with reagents. Starting with a feed grade of 7.6% REO, concentrates having a grade of 65% REO can be produced at a recovery of around 80%. A detailed investigation consisting of Hallimond tube microflotation experiments, bench-scale tests with a laboratory Denver flotation cell, and predesigned plant campaigns was made to delineate the underlying surface chemistry involved in this separation and to develop an alternate reagent scheme to enhance the selectivity of separation for this ore. Our results clearly demonstrate the superiority of alkyl hydroxamates to the conventional fatty acid collectors that were being used in the plant. Our study also indicates the possibility of achieving the desired selectivity with alkyl hydroxamates even at room temperature, thus obviating the need for steam conditioning. A critical review of the literature on rare-earth mineral flotation suggests the possibility of designing a more selective reagent combination for the beneficiation of Mountain Pass rare-earth ore, using a methodology based on ab initio molecular modeling computations.

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

Almost all of the flotation reagents used today were discovered by continued application of empirical methods and/or trial and error experimentation. Moreover, with the metal-ion specific approach used so far, it is difficult to separate the minerals containing the same constituent metal ion. A critical assessment of molecular recognition processes involved in biomineralization suggested the possibility of using reagents which are surface specific. The concept that the molecules consisting of two or more functional groups having appropriate spacing between those so as to achieve structural/stereochemical compatibility during interaction with the mineral surface exhibit structure-specificity is thought to be extended to the design of specific collectors in flotation processes. In the present study, for the first time, a rational design of surface active molecules, and thereby the recognition of crystal faces (of minerals) by these molecules through structural and stereochemical matching is being utilized successfully to selectively float various minerals. For this purpose, carboxylate-based collectors (for mineral specific flotation of calcium minerals) as well as xanthate-based collectors (for mineral specific flotation of sulphide minerals) with a fixed alkyl chain length but having two functional groups with varying geometrical distances (separated by a spacer of one, two and three carbon atoms) between them have been synthesized. In this article, we have discussed the design, synthesis, purification of these novel mineral specific collectors as well as their important solution parameters in relation to flotation processes.

Jan 1, 2014

By Wickham P, Raeburn M. R

The design and development of slurry sampling equipment for the Mount Isa Mines Limited on stream analysis installations is discussed in detail. Emphasis is given to the critical areas of slurry transport, screen design, pump selection, elimination of fast wearing components and maintenance reduction. Sample point design to fulfil the specific accuracy requirements for On Stream Analysis (3% to 10% relative) is discussed.

Jan 1, 1976

By Nick Rose, Robert Sharon, Mark Rantapaa

Development of the Northeast Layback of Barrick’s Betze-Post open pit commenced in June 2000 and was successfully completed to a height of 400m (1,300 ft) in January 2003. Following a brief exploration drilling campaign at the toe of the final slope, in-pit waste rock backfilling commenced, which will ultimately buttress the final wall. Instability initially occurred in late 2000, above the 5040 Level, as the slope height approached 120m (400 ft). As mining reached the 4680 Level, significant deformation was experienced over a slope height of 230m (760 ft). Slope stability was managed and targeted reserve recovery was achieved by executing complicated modifications of the mine plan, including splitting layback development, well placed offloading cuts, step-outs and mid-slope waste rock buttresses. Decision on timing of these modifying events was often dictated by review of deformation magnitudes and rates determined from continuous slope monitoring records. Design modifications were developed through continuing interpretive refinement of structural geology controls and groundwater distribution, and through stability re-assessments. This document presents an overview of the geological setting and material and strength conditions of the northeast sector of the Betze-Post open pit, followed by development experience leading to design and development of the Northeast Layback. Rock mechanics modeling, design details and geotechnical performance monitoring are then presented. Development experience, stabilizing adjustments to the original design and safety procedures for development and exploration activities are described. The document is finalized with conclusions and acknowledgements.

Jan 1, 2005