Search Documents

By B. Derin, T. Uzunoglu, O. Yücel

In this study, reduction behaviours of Turkish chromite concentrate (48 % Cr2O3, 13.30 % FeO, 18.33 % MgO, 12.37 % Al2O3, 5.76 % SiO2) and nickel oxide by Fe-C alloy in graphite crucible were investigated. In the first stage of experiments, steel scraps were melted in graphite crucibles and were saturated with carbon at 1600 °C and 30 min. In the second stage, mixtures of different amount of chromite concentrate, nickel oxide and flux additives (CaO,SiO2 and CaF2) were charged into the graphite crucible containing the Fe-C alloy and heated to 1600 °C for different reduction times (0-180 min) under argon gas. The highest Cr and Ni con-tents in alloys were found as 11.41 and 14.37 % and the highest Cr and Ni recoveries were found as 88 and94 %, respectively at 180 min.

Jan 1, 2007

By Jian Pan, Deqing Zhu, Benjing Shi, Yuxiao Xue

COREX smelting reduction process which is freed of metallurgical coke provides a sustainable developing way for ironmaking industry. However, the shortage and high cost of pellets limit its development in China. Meanwhile, iron ore sinter has a great output in China. This work studied the reduction behaviors of sinter made from magnetite concentrates during the reducing process of COREX shaft furnace and compared the RI and RDI of sinter with BF process. The results showed that the reduction degree of sinter increased obviously during the temperature zone from 600 to 850 °C, while the reduction degradation presented rapidly aggravate in the temperature zone from 425 to 550 °C in COREX shaft furnace, and the increase of metallic iron content leads to the degradation of sinter got decreased slightly during the stage of temperature above 650 °C. Sinter got higher RI than BFprocess but also got higher RDI in low reduction temperature of 550 °C, which means sinter would have heavier disintegration in COREX shaft furnace.

Mar 1, 2017

By Maria de Campos

The pre-reduction behaviour of chromite particles in methane-argon and methane-hydrogen gas mixtures was investigated between 1050°C and 1250°C. Loose bed of chromite particles were reacted in a vertical tube furnace under a pre-set gas mixture predetermined time intervals. Metallization results were obtained for the Cr and Fe components by chemically analyzing the reaction products. SEM-EDAX techniques and X-ray diffraction were employed to elucidate the reduction mechanism. It was found that higher reduction kinetics and higher Cr:Fe ratios in the metal phase would be achieved when hydrocarbon gas was used in comparison to classical carbothermic reduction at a given temperature. The reduction rate was generally bulk gas mass transfer controlled to the reaction site for initial stages which then was followed by ionic diffusion rate control. It is proposed that methane did not partake directly in the reduction but cracked, presenting the reaction site with hydrogen gas and atomic carbon, which was able to immediately react at the immediate area of reduction regeneration CO and H2 and thus maintaining a low partial pressure of oxygen at the reaction site.

Jan 1, 2006

By J. Härkki, R. Hiltunen

The Akanvaara intrusion (surface area 50-55 km2) in Savukoski, Northern Finland, hosts 23 distinct monocumulate layers of small euhedral chromite crystals enclosed in a silicate matrix. These chromitite layers have been divided into four groups; UC (upper chromitite), ULC (uppermost lower chromitite) LC (lower chromitite) and LLC (lowermost lower chromitite). The driving force for investigating the Akanvaara chromites and their reduction behaviour originated from their very low MgO content and relatively low Al2O3 content, giving them a unique quality which based on thermodynamics should facilitate the reduction. Another interesting feature is the high amount of V2O3 present especially in the upper chromitite. The chromites included in this study are from the UC and ULC layers (24.9 and 22.7 per cent Cr2O3 respectively). To obtain a better understanding of the reduction behaviour of Akanvaara samples in comparison to MgO-bearing chromitites, Kemi chromite from the ferrochrome works in Tornio, Finland, was included in the study as a reference sample. The reduction experiments were isothermal in a temperature range of 1000-1400°C in CO atmosphere. Experiments were also conducted with coke addition in pellets and briquettes in CO/Ar/H2 atmospheres. The results of the reduction experiments complemented with microanalytical research indicate that the Akanvaara chromites do reduce to a higher degree than the Kemi chromite. Although the aim was to characterize the mechanisms of reduction focusing on gas-solid reactions, the nature and amount of the gangue minerals was such that a considerable amount of slag phase was formed, which affected the reduction mechanisms extensively. The structural features together with low MgO and high FeO content in both Akanvaara chromites are important factors resulting in better reducibility than in the Kemi chromite.

Jan 1, 2004

By Jian Zhang, Yongfu Yu, Fuguang Zhang, Liping Che

There is one large-scaled iron ore deposit in Inner Mongolia of China, but it is very complex which includes about 170 types of minerals and 71 elements. The hematite, magnetite are mainly iron ores. It is difficult that the iron mineral can be separated efficiently by common dressing methods due to the complexity, and the iron concentrates in the mineral processing factory contains many foreign substance such as K, Na and Si so that the process in iron mill is influenced because of the foreign substance, so it is vital reducing the foreign substance.

Jan 1, 2003

By Luana Lessa Pacheco, Antônio Vitor Magalhães Cota

With the sharp fall in commodity prices, the terms cost reduction and higher productivity have become subjects that are constantly addressed in the daily life of companies, since these factors represent a question of survival of the organizations. To achieve this, the search for continuous improvement of our processes in order to guarantee space in the market is a reality and necessity, so it is important that companies know their processes in detail and have the maturity to make decisions based on data and facts. Thus, this work aims to apply the Six Sigma methodology to investigate which are the variables that most influence the transportation process, carried out by large trucks, increasing their specific consumption of diesel, which is the second largest expense of a company. mining in the city of Mariana MG. The goal of the project was to reduce diesel consumption in the large transport fleet by 7.4%, from 0.32 l / t (average carried out from Feb / 16 to Jan / 17) to 0.30 by February 2018 , with an estimated gain of R $ 4.2 million. The results achieved exceeded the established target, reaching a 10% reduction in specific diesel consumption, totaling a projected real gain of R $ 6.4 Million, in addition to the reduction of 1,710.52 t of CO2 in the atmosphere.

Oct 3, 2019

By A Melloy, D Holt, M Jurak

Oaky North is AustraliaÆs highest producing underground coal mine. In 2011, the mine produced 8.7 Mt of high-quality coking coal. The high quantities are a result of the constant strive for optimising the operating time of major production units, which involves investing numerous resources, including diesel equipment, in supporting and maintaining their operation.In July 2011 it was identified that the diesel particulate matter (DPM) levels in the underground workings were above acceptable levels, due to the high level of diesel activity. Over the next 12 months, several controls were implemented to reduce exposure to personnel: the main ventilation system was upgraded; the production forecast was adjusted to better manage the diesel fleet, removing surges in diesel usage; and an electronic diesel tag board was introduced to centrally manage the distribution of diesel usage around the mine.From the start of the campaign in emission reduction, an intense DPM monitoring regime was established. Within a few months of the introduction of the centralised tag board, there was a major reduction in emission levels. After the installation and commissioning of the new main fans, the emission levels dropped further, such that over-exposures are now a rarity.Oaky North continues to explore new systems to better utilise their diesel fleet while still maintaining control over DPM emissions.CITATION:Melloy, A, Holt, D and Jurak, M, 2013. Reduction in diesel particulate matter at Oaky North, in Proceedings The Australian Mine Ventilation Conference , pp 187-190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific and the U.S. National Institute for Occupational Safety and Health (NIOSH) combined efforts to evaluate an in situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was preloaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both realtime and time-weighted-average approaches. The real-time measurements were performed with a Model AE33 aethalometer, and filter samples analyzed by the NIOSH 5040 method were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82 to 89 percent. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the aethalometer were higher, possibly due to differences in the performance of the size selectors used for the two methods: impactors versus cyclones. More research is required to develop a robust correlation between the two methods to support the use of the aethalometer in future mining applications. The advantages of the aethalometer are that it can measure and record DPM levels for weeks at a time and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally, such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise in reducing DPM concentrations in the mine environment.

Mar 1, 2017

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific, and NIOSH have combined efforts to evaluate an in-situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an Aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was pre-loaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both real-time and time-weighted-average approaches. The real-time measurements were performed with the model AE33 Aethalometer® made by Magee Scientific. The results of the NIOSH 5040 method analysis were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82%-89%. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the Aethalometer were higher, possibly due to differences in the performance of the size-selectors used for the two methods (impactors versus cyclones). More research is required to develop a robust correlation between the two methods, to support the use of the Aethalometer for future mining applications. The advantage of the Aethalometer is that it can measure and record DPM levels for weeks at a time, and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in-situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise at reducing DPM concentrations in the mine environment.

Jan 1, 2016

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By R. I. Rodriguez

Since the 1973 energy crisis, high fuel oil costs have been eroding the economics of the Nicaro and Punta Gorda Plants that employ the Caron Process for laterites processing. Since 1995, Cuban crude oil production has growth dramatically, with progressive utilization in power generation, cement and nickel plants. This paper shows how Nicaro and Punta Gorda plants have been able to shift from expensive Bunker C Fuel Oil to heavy but cheaper Cuban Crude Oil of high Sulfur content and achieve a significant reduction in operating cost. Problems related to the high sulfur content of the Cuban crude oil have demanded extensive investigations of the process chemistry and novelty solutions are proposed, with corresponding changes in process conditions. Innovative options are shown that will allow further cost reductions in the future. Keywords: Cuban Crude Oil, Sulfur, Ammonia.

Jan 1, 2004

By R. C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1984

By Wing Ka Ng

Substitution of pulverized coal injection by solid biocarbon fuel has the potential to achieve substantial reduction in GHG emissions associated with blast furnace ironmaking. A systematic evaluation was conducted on the performance of solid bio-carbons produced from a single raw biomass source using different pyrolysis technologies. The potential of solid biocarbon in reducing GHG emission of the blast furnace ironmaking process is strongly influenced by its O/C mass ratio. In order to achieve substantial GHG reduction, it is necessary to replace coal injection by solid biocarbon having a low O/C mass ratio. The pyrolysis technology and conditions employed are key parameters influencing O/C mass ratio of the resultant solid biocarbon. Close collaboration between steelmakers and solid biocarbon producers is critical for producing suitable solid biocarbon fuel to replace pulverized coal injection. A successful partnership should pave the way in achieving substantial reduction in GHG emissions of the blast furnace ironmaking process.

Use controlled blasting techniques to reduce blast-produced overbreak damage to underground mine ribs and back for both safer working conditions and improvements in productivity. The Problem Blasting is used in metal and non-metal underground mine slopes, drifts and crosscuts to fracture rock to be excavated and further processed. Standard blasting also produces fractures in the rock beyond the desired excavation area. This is sometimes evident by rough surfaces, undercutting and other signs of excessive damage. This damage contributes to rockfalls in the mines, a major cause of injuries and fatalities, and equipment damage. A variety of controlled blasting techniques has been developed for civil engineering projects where long-term stability is essential. For several reasons, these methods arc not widely used in mining. For example, these methods incur additional costs and time; there is little need to maintain stable openings over long periods of lime; and there is the perception (hat corrective remedial techniques, such as rock bolting, are more practical. Basically the benefits of these methods are not demonstrably clear for application in underground mines.

Jan 1, 1991

By Narendra Gupta, Gaurav Srivastava, Abhinav Sharma

From the days when plain detonators and safety fuse were used for initiation of commercial explosives, the commercial blasting and mining industries have made rapid strides. With the advent of electronic detonators in the late ‘90s, the face of commercial blasting was changed forever. The Mining Industry in India initially took a while to embrace Electronic Blasting Systems (EBS), however, more recently the industry has taken to EBS in a big way.

Jan 1, 2015

By P N. Duan, Z G. Liu, M S. Chu, X X. Xue, B Liu, G J. Cheng, T Jiang, J X. Liu

High-chromium vanadium-titanium magnetite has not been exploited and made full use of on a large scale so far due to the immature utilisation technology and the reality that the utilisation efficiency of valuable metals still urgently needs to be improved. In the present paper, the isothermal reduction kinetics and mechanism of high-chromium vanadium-titanium pellets were studied at 800–1100°C. The mineral composition transformation of pellets before and after reduction was analysed by means of X-ray diffraction (XRD), and the microstructures were examined by scanning electron microscope (SEM) equipped with energy dispersive X-ray (EDX) to reveal the elemental distributions. The effect of reduction temperature on the volumetric swelling degree and cold crushing strength was also studied. It was found that reduction temperature has a large effect on the reduction rate of pellets, and the increase in reduction rate is more obvious in the range 1000–1100°C than 800–1000°C. The volumetric swelling degree of pellets increased with increasing reduction temperature, while the cold crushing strength decreased. The transformation of mineral species can be expressed as Fe2O3 ? Fe3O4 ? FeO ? Fe, Fe2O3·3TiO2 ? Fe3O4· (2FeO·TiO2 ) ? 2FeO· TiO2 ? FeO·TiO2, (Fe0.6Cr0.4)2O3 ? FeO· Cr2O3 ? Cr2O3 , and Fe2O3· VO/V2O3 ? VO. The apparent activation energy of the reduction reaction was calculated to be 44.3 kJ/mol, and the reduction rate is controlled by the combined effect of interfacial chemical reaction and gas diffusion through the porous product layer. The rate controlling steps were further studied by calculating the resistance percentages. The interfacial chemical reaction was found to be predominant in the initial reduction stage, with the percentage effect of gas diffusion through the porous product layer gradually increasing during reduction.CITATION:Cheng, G J, Xue, X X, Liu, J X, Liu, Z G, Chu, M S, Jiang, T, Liu, B and Duan, P N, 2015. Reduction kinetics and mechanism of pellets prepared from high-chromium vanadium-titanium magnetite concentrate, in Proceedings Iron Ore 2015, pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Emmanuel N. Zevgolis Ismene-Polyxeni Kostika

Keywords: reduction, kinetics, laterites, rotary kiln, dust In this work, the reduction kinetics of dust from nickeliferous Greek laterites is investigated. The dust is a by-product from laterite treatment in rotary kilns and it comes from washing towers, electrostatic filters and polycyclones. Laboratory made pellets from this dust were also examined. Reducibility was studied in the temperature range of 700°C to 850°C in a laboratory tube furnace. Kinetic analysis of the results showed that at lower temperature values the mixed kinetic model verifies the experimental results of dust and pellet samples. At higher temperatures (800° and 850°C) diffusion becomes the rate controlling mechanism. The calculated activation energy values verify also the above mentioned results.

Jan 1, 2005

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

The kinetics of hematite concentrate reduction by mixtures of hydrogen and CO of various compositions has been investigated as part of the development of a flash ironmaking process at the University of Utah. This process produces iron directly from iron oxides concentrates by the gas-solid flash reaction based on the partial oxidation of natural gas, resulting in a significant reduction in energy consumption and greenhouse gas emission. The reduction kinetics of hematite concentrate of an average particle size 21.3 μm by the above mentioned gases in the temperature range 1423 to 1623 K (1150 to 1350 ºC) was investigated. Hematite concentrate particles can be reduced to > 90% by any of these reductants in several seconds of residence time typically available in a flash reactor. The activation energy ranged from 214 kJ/mol for hydrogen to 231 kJ/mol for CO.

Jan 1, 2016