Search Documents

By H. Scott

IN a paper read before the Institute of Metals, Rosenhain 1 described a new type of furnace designed primarily for the thermal analysis of metals by the inverse-rate method and used by him in the metallurgical department of the National Physical Laboratory with considerable success. In his discussion of this furnace, Rosenhain pointed out some difficulties met with in its operation, such as uniformity of rate of heating or cooling being inadequate for the degree of accuracy aimed at. To overcome this difficulty, he suggested, in place of motor propulsion, a gravity drive controlled by a"hydraulic cylinder with a relief valve whose width of opening can he regulated to allow of any desired rate of motion." The authors, in constructing a thermal-analysis furnace of Rosenhain's type, have therefore followed this suggestion and also added certain features that increase somewhat the convenience and simplicity of its operation. Requests for information regarding this furnace and the highly satisfactory results obtained from its use, it is believed, justify describing its construction and operation in sufficient detail to make possible its duplication or improvement. Description of Furnace.-The details of the furnace construction are shown in Fig. 1, which is drawn to scale. The heating tube is of /4 in. (6.35 mm.) wall "alundum" heated at the upper end by seventeen turns of 0.52 mm. platinum wire, which is coated with "alundum" cement supplied for this purpose. The cement coating is essential when a high temperature (over 1000° C.) is required, as it prevents hot spots with the resulting burning out of the heater. This platinum-wire winding, unlike "nichrome," is entirely satisfactory for temperatures of at least 1000° C. It has been maintained at that temperature continuously for 2 months and shows no signs of deterioration. This temperature is maintained by a current of 5 amp. drawn from 30 volts potential, so its necessarily continuous operation is quite economical.

Jan 8, 1919

Valuers will often intuitively express the probability that property value will exceed a certain amount . . . 'I think the chances that the value will exceed $50 million are excellent. The chances that they will exceed $80 million are poor'. This paper shows how it is possible to combine the uncertainties of the value of several key items to provide an estimate of the probability of a certain overall value being achieved. The valuation of a large copper/gold deposit was naturally influenced by uncertainties in the base assumptions of costs and metal prices. Potential acquisition of the property through share purchase raised the issue of what was a reasonable intrinsic value for the shares. Market considerations could be used to appropriately adjust the intrinsic value. After a range of possible metal prices and operating costs were determined, estimates were made of their probable distributions. By combining these probabilities in a random selection, a range of property values was calculated. Each value had its respective probability of occurrence. This allowed a most likely value of shares to be calculated. This paper demonstrates how the valuer's intuition is complemented by numerical analysis.

Jan 1, 1994

By J. A. Rose, A. S. Atkins

Environmental awareness has become a paramount consideration in the issue of planning and licensing arrangements for the disposal of wastes associated with mining operations. In this con- text the disposal of liquid tailings is a difficult and controversial problem with regard to environmental surface disposal. The paper outlines the use of Information Systems for decision support in the safe and environmental disposal of liquid tailings linked to conventional coarse refuse operations. This offers both an economic and an aesthetic approach to a historical perception of waste tipping in the underground coal extraction industry. The paper will demonstrate a prototype system that incorporates multimedia facilities which include data such as; voice comments, site photography, site plans and fluid flow circuits.

Jan 1, 1996

By C. Dragusanu, J. Sims, J. Connolly

Based on a statistical analysis of the categorical and numerical data from the established geological model, a geochemical classification of mineralization has been shown to be objective in nature and correlated to the envisioned metal extraction process. Multivariate chemical classification has the potential to discriminate within a combined response from different types of alteration and metal abundances. Distinct domains of chemical response determined by clustering analysis were used as a validating criterion for a geologically driven metallurgical testing program. The groups established are spatially linked to the geological process responsible for their genesis, providing clarity in geometallurgical and resource modeling.

Jan 1, 2011

By K. S. Izbakhanov

The Chimkent Lead Plant was constructed in 1934 and since that time has undergone many revisions. In 1975 the slag fuming operation was changed from pulverized coal to natural gas fuel. In 1981 the slag fuming furnace water jacket system was converted to evaporative cooling with high pressure steam production. The impact of these changes and the method of their application are described.

Jan 1, 1990

By R. M. Carland, F. F. Aplan

Six natural zeolites were evaluated for their ability to selectively remove heavy metal cations from solution. Ion selectivity was found to be Pb+2>Zn+2>Ni+2 and Cu+2>Co+2 from their respective solutions. The presence of K+, Ca+2 and Mg+2 in the actual waters to be used may seriously interfere with the ion exchange and elution of cations from zeolites. Zeolites were found not to be effective in removing precious metals from their cyanide solutions.

Jan 1, 1995

By Andrew Barnes

The adsorption capacity of peat collected from a proposed mine development in northern Sweden has been determined using laboratory column experiments in which peat was irrigated with a simulated (acidic) waste rock dump leachate. The simulated leachate was made using a hydrogen peroxide leach of composite waste rock from the proposed mine development. The waste rock samples were composited in proportion to their predicted extractable tonnage for the mine development in order to generate a more representative leachate solution for the waste rock facility. As expected the test revealed that the peat material shows a very high affinity for attenuation with greater than 70% of Co, 90% of Ni and 95% of Cu removed from influent solutions through the majority of the tests demonstrating the potential benefits in mine water treatment. In contrast, it was found that Fe is initially released from the peat at concentrations up to 100 mg/L and can mean potential problems for the water released depending on the receiving environment. The exact mechanisms for Fe release is uncertain, though it is suspected that ion exchange / competitive desorption is responsible. Inspection of the laboratory results and drainage data from the natural peat wetland receiving drainage during overburden prestriping and mine development at the mine site are comparable, confirm the validity of the experiments, and further emphasize the potential for future use of pre-stripped peat material in managing water quality.

Aug 1, 2013

By Xin Tan

In this paper, two types of low-grade complex zinc oxide ores (sandstone and limestone ores) from Yunnan province, China were investigated. A large number of argillaceous and alkaline gangue makes it infeasible to treat the ores with heap leaching. Although wet metallurgy can be considered, the lower efficiency of liquid-solid separation, the high cost, and low revenue limit this technology to be put into practice in large-scale. In order to solve this problem, a new technology combining mineral processing method with metallurgy technique is studied to process this refractory ore that consists of sandstone ore with 5.84 per centZn and limestone ore with 6.50 per centZn. The results of the tests showed that zinc can effectively be recovered from two types of the ores by using the new technology, and the acid consumption can be remarkably reduced. For sandstone sample, 82.96 per cent Zn was recovered by flotation and final Zn recovery by flotation+ hydro-metallurgy can be up to 78.17 per cent from the ore. In addition, for sandstone, acid consumption can be reduced from 270kg/t by direct acid, leaching to 76.92kg/t by flotation + hydrometallurgy combination. For limestone sample, 85.90 per centZn was recovered by flotation and totally 80.95 per cent Zn can be recovered by new technology which is a combination of mineral processing and metallurgy. Besides, H2SO4 consumption can be reduced from 450kg/t for sandstone originally to113.79kg/t after using new technology. One merit of this new process technology is that the zinc sulfides and oxides can be recovered without desliming in the flotation cells at the different stage and make sure the concentrate products as a good feed for hydrometallurgical technology. This study provided pretty good technical support for tapping low-grade refractory zinc oxide ores. Keywords: low-grade zinc oxide ores, limonite, non-desliming beneficiation, flotation + hydrometallurgy combination

Sep 1, 2012

By FLOYD T. TAYLOR

IN 1833, less than one hundred years ago, Michael Faraday discovered and stated the laws of electrolysis. His discovery formed the foundation of a new use of metals which has now reached a variety of application not ordinarily appreciated. Furthermore, things can be done with electro-deposited coatings which have thus far defied other methods. Some of the uses of electro-deposited coatings are interesting. The tonnage of metals already finding an outlet through such a channel is considerable. In general electro-deposits have two characteristics: ornament plus utility; utility plus ornament. Both these factors are usually found associated in electro- deposits. Ornament plus utility was probably the first use. For example, the silver-plating of tableware, having its real birth in Birmingham, England, about 1844. However, this same ornament plus utility retarded the development of electro-plating, because in the beginning, electro-plated articles were branded with the odium of imitation and shunned accordingly. The gold brick of the swindler may be an exception to this statement.

Jan 1, 1929

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By B. Alegria

The depressing effects of different inorganic chemicals on the flotation of pyrite have been investigated in this study. The results of the flotation tests indicate that pyrite can be depressed by oxidizing as well as reducing agents under controlled conditions of pH and reagent dosage. Oxidizing reagents such as potassium chromate and potassium dichromate were found to cause complete depression of pyrite in the acidic pH range. These effects are similar to those obtained in the pyrite-cyanide system. A less stable oxidant, potassium permanganate, inhibited the flotation of pyrite at a concentration as low as 0.1 mol/L at all pH values, Addition of reducing chemicals such as ferrous chloride or manganous sulphate to the flotation of pyrite were found to produce depressing effects depending on the additive concentration and pH of the solution.

Jan 1, 1982

By Clyde Baker

Drilled shafts for many situations offer an economical alternative to driven piles. The Federal Highway Administration (FHWA) has spent considerable time and money in research and developing design and construction guidelines for drilled shafts. However, the full potential of the technology may not be realized because of the uncertainty of the effects of construction on the actual service behavior and the lack of either reliable quality control tests to check for or evaluate defects, or inexpensive load test procedures. Static load testing is very expensive and it is not feasible to load test each shaft on a project. Therefore, other means are necessary to confirm or evaluate the integrity of the completed drilled shaft or to determine the capacity of the completed shaft.

Jan 1, 1989

By J. Jung, W. Keller, A. Zucht

"The agitator design for nickel high pressure acid leach autoclaves (HPAL) is critical with regard to the process result, i.e., the recovery rate. Further considerations during the design phase are the avoidance of acid hot spots which reduce the lifetime, due to corrosion of the wetted parts, including components manufactured from titanium. Besides the process knowledge to design HPAL autoclaves, tools such as, Computational Fluid Dynamics (CFD) supplemented by lab testing allow the design of optimized agitation systems. This paper describes the effect that different feed point locations have on instantaneous blending of the reactants. Furthermore, experiments and CFD show where abrasion issues might occur and how to obtain information about the static and dynamic forces acting on internals. We show how simulations can be validated by lab testing to ensure that the CFD models are applied in an appropriate way.INTRODUCTIONAgitated systems in hydrometallurgical processes have to comply with multiple process tasks and in many cases have to withstand extreme operation conditions such as pressure up to 50 bar, elevated temperatures of up to 250°C and exposure to very acidic or alkaline environments and abrasive ores. The process tasks range from instantaneous mixing of reactants, homogeneous suspensions of up to 65% wt. solids with coarse and heavy particles, enhancing the solid-liquid mass transfer for leaching, dispersing large volumes of reactants (gas-liquid, liquid-liquid mass transfer) and moreover to transport generated heat e.g., from exothermic reactions through the vessel walls or internal heat exchangers if required. For economies of scale, agitator systems have reached sizes of 5000 m³ for large open leach tanks with impeller diameters of approx. 6 m, while autoclaves nowadays have exceeded 5.5 meters in diameter with a power demand for a single compartment drive between 300 - 400 kW. In parallel all process industries require a more efficient use of resources, to generate less by-products and higher yields, while ore-bodies tend to be less qualitative and new process routes (e.g. direct leach) are developed. Besides all these facts the mixing solution must be robust and economic. In this paper we want to address our approach in the development and designing of HPAL agitation equipment."

Jan 1, 2012

By B. Hearn, O&apos

Falconbridge, Ltd. operates six mines (the strathcona, Fraser, Lockerby, Onaping, East and Kidd Creek) in the Sudbury and Timmins districts of northern Ontario (Fig. 1). These mines vary in depth to approximately 1500m and experience a wide variety of ground conditions. Problems of greatest concern include rockbursting, backfill pillar stability, wall and pillar stability, and the use of cable anchors. A study was initiated approximately two years ago to identify how numerical models could aid in the examination and possible understanding or solution of these problems. This paper discusses the use of numerical models at Falconbridge and describes a case history of their use in examination of rockbursting at the Strathcona Mine.

Jan 1, 1988

By Fatima-Zahra Houmymid, Elena Chiriotti, Mahdi, Samy

"The Greater Paris projects involves the creation of a 200km extension of the actual public transport network on the close outskirt of Paris. In 2011, SYSTRA has been awarded the Engineering studies of a 20km underground section in the densely urbanized southeast quarter of the Parisian suburb. In order to both guide the TBM technology choice and identify and mitigate the risk due to soil settlement during tunnel boring, several analysis have been carried out and integrated into a Geographical Information System to share and manage this risk during the successive design phases of the project. The geological context‘s complexity and the Owner‘ requirements have led to the necessity of using an innovative analysis approach, leveraging both the numerical modelling analysis’s accuracy and the analytical method‘s ease of programming and implementation in a GIS, by the mean of the calibration of the analytical approach’ parameters on the FEM results.INTRODUCTIONThe Greater Paris Transport Project foresees the extension of the actual public transport network to the close outskirt of Paris through the extension lines 11 and 14, the creation of a circular new line around Paris - line 15 completed by lines 16 and 18 linking developing territories - and line 17 to Roissy-Charlesde- Gaulle airport.The SOCIETE DU GRAND PARIS (SGP) is the public institution that promotes this project and awards SYSTRA as Engineering for the 15th Line southeast section.Line 15th – South-East sectionIn 2011, the Owner SGP (SOCIÉTÉ DU GRAND PARIS) awarded to SYSTRA the preliminary and detailed design of a 20km-long underground section of Line 15, between the stations of Villejuif-Louis-Aragon and Noisy-Champs. The double-track, single-tube tunnel has an inner diameter of 8.5m (about 9.8m excavated diameter, 75m2 excavated cross-section). The tunnel is inserted in a densely urbanized context."

Jan 1, 2016

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

By M Edwards

The paper outlines the successful application of some of the on-belt technologies available from Scantech International Pty Ltd and how these have provided benefits in a number of mining and mineral processing operations. Effective process control requires real time analysis so quality can be fed back to the previous process and fed forward to a subsequent process. A range of on-belt analysers that allows for full stream, continuous, non-contact analysis of conveyed materials is available to achieve this. Real time results can provide timely information for effective process control. Benefits of on-belt analysis systems become more evident once the true variability of material quality and moisture content in conveyed flows is measured. To obtain economies of scale in mineral processing operations large material flows are achieved using conveyors. The cost and effort to sample representatively increases as conveyor flows increase. One sample may represent a few tonnes or up to 10 000 tonnes of material. The turnaround time between sampling and availability of sample analysis data does not allow real time process control. Tonnage flow rate, moisture content and elemental or mineralogical composition are required to perform effective process control of most conveyed streams. Tonnages can be effectively measured using belt weighers. The analyses derived from small samples supplied by conveyor-based sampling systems contain high variability. On-belt, continuous analysers see all the material and, through short term compositing of analyses, supply less variable results. Real time analysis helps operators develop a better understanding of material variability. Analysers can be effectively utilised to improve the consistency of product quality through bulk sorting and blending control. Many existing users of the technologies have gained competitive advantages through their ability to supply a more consistent quality product to the market.

Jan 1, 2008

By F Pavloudakis

The installation of on-line analysis systems in the open-pit mines of the Public Power Corporation SA (PPC, the state-owned electricity entity of Greece) is considered to be the key-parameter for performing improved quality control and blending/homogenisation of the produced lignite. In order to investigate the accuracy of these systems under the site-specific conditions of the Greek lignite deposits, a research project was carried out. This was necessary since there is lack of experience in using on-line analysers in mines that produce a fuel of such a poor and largely fluctuating quality. After thorough market research, a dual energy gamma ray transmission on-line ash analyser was installed in Kardia mine of Ptolemais û Amynteon Lignite Centre, which is located in West Macedonia, Greece. The initial results obtained after the realisation of a series of dual-comparison trials (ie using two series of reference values that allow three-way comparisons) pointed out several problems that obstacle the achievement of high accuracy on-line measurements. More specifically, the measurements obtained by the analyser were higher than the concentrations determined by the two laboratories when the ash content was lower than 12 per cent (in wet basis). On the contrary, when the ash content was higher than 12 per cent, the measurements of the on-line analyser were lower than the concentrations determined by the laboratories. In other words, the range of the measurements obtained by the analyser was narrower than that corresponding to the lab analyses results. Therefore, the use of this on-line analysis system under the site-specific operating conditions of Kardia mine does not guarantee improved quality control of the lignite fed to the mine-mouth located power plant. Most probable reasons that explain the above-mentioned problems are the following: The frequent and widely ranging fluctuations of the chemical and mineralogical composition of the lignite transported by the conveyor belt, especially as far as its calcium content is concerned. This result from the nature and the origin of the mineral matter co-excavated with the lignite, which varies from calcareous marls to sands and clays rich in aluminium and silica minerals. The fluctuations of the lignite quantity transported by the conveyor belt. The change of the linear concentration of iron contained in the fabric of different belt parts.

Jan 1, 2003