Search Documents

By Kent D. Gastreich

As the number of prime surface coal mining sites diminishes with time and with the potential for increased coal demand, areas that were previously not mined because of their difficult mining conditions, marginal economics, and controversial environmental nature, will have to be considered if surface coal mining is to continue in the future. Such sites include areas near major rivers, streams, and lakes. The name most commonly given to these areas by regulatory agencies is "wetlands". The exact definition(s) to the term "wetland" will be discussed later in this paper. Most coal operators are now more than familiar with permitting requirements under the Surface Mining Control and Reclamation Act of 1977 (SMCRA). The SMCRA permanent regulatory program recognizes the fact that coal mining operations will periodically encounter streams, wetlands, etc. Although discussed in various sections of the permanent program regulations, the relationship of coal mining operations to wetlands is particularly evident in the performance standards regarding hydrologic balance and protection of fish, wildlife and related environmental values.

Jan 1, 1980

By P. Knüpfer, B. Babel, M. Rudolph, F. Perez Maldonado, U. A. Peuker, L. Ditscherlein

"In heterocoagulation processes for the separation of mineral particles, the most famous being froth flotation, the main characteristic of separation is a differing wettability of the constituents to be separated. This most crucial property in the economically important process of flotation is often only and incompletely, quantitatively described in terms of contact angles against water. A water contact angle larger than 90° is referred to as hydrophobic and hydrophilic vice versa. Looking at Young’s equation shows that it is actually the surface energy of the solid in interaction with the surrounding phases and their surface energies (or surface tensions for liquids) which describes whether there will be hydrophobic/hydrophilic hydration interactions leading to attraction or repulsion. This, we have previously published for various more or less hydrophobic minerals in correlation to their flotation response, i.e. flotability (c.f. Rudolph & Hartmann, Coll.Surf.A 513, 380-388). In the same paper we also discussed the heterogeneity of wettabilities as assessed with the novel method of inverse gas chromatography. Furthermore we have also reported on hydrophobic force distributions as assessed with atomic force microscopy which are as well due to wettability heterogeneities (c.f. Fritzsche et al., Coll.Surf.A 459, 166-171).In this paper we present wettability distributions of different substrates and particles with various surface roughnesses/shapes and degrees of hydrophobization as assessed with iGC, AFM and dynamic sessile drop analyses. We are putting the results in context in unifying models and present methodologies helpful to make use of the fundamental information and their impact on the actual industrial separation process in fundamental process models. Besides froth flotation we also emphasize the impact on selective hydrophobic flocculation process."

Jan 1, 2018

By A. Atrafi, L. Barroilhet

The top size of particles in the flotation of potash ores, which can be as large as 4 mm, exceeds by far the top size in other flotation plants. It is then understandable that while long chain amines are used in the flotation of fine fractions (below 0.8 mm) of potash ores the coarse particle flotation also requires an extender oil. While new and very promising fluidized-bed flotation machines (e.g. HydroFloat) constitute a significant development in the flotation of coarse particles, in the area of extender oils, as reviewed in 2007 by Strathdee, Gotts and McEachern, there have been no new developments to replace the industry standard asphaltene-based carcinogenic extenders. This situation first of all results from the experimental problems that arise when water-soluble minerals like sylvite are to be tested in saturated brine. Both oils and longchain amines are water/brine insoluble. The oil with the amine dissolved in it can however be emulsified and then used as an extender oil. Such oil droplets must wet KCl particles and the emulsion must be stable to avoid handling problems. In this paper we test the use of the phase inversion technique as a method of studying wettability of KCl particles by the oil in saturated brine, and the effect of amine dissolved in this oil on the wettability. The results show that this relatively simple technique can be used to characterize the wettability of fine KCl particles by the tested oil and to determine the effect of added amine on it, and so it can be useful in selecting proper extender oils.

Jan 1, 2016

By X. Yin

Surface force measurements based on atomic force microscopy (AFM) are used to describe the wettability of surfaces, specifically kaolinite basal plane surfaces at a high resolution. The kaolinite particles (~500 nm) were ordered with either the silica tetrahedral face exposed or the alumina octahedral face exposed, and surface force measurements were made between a hydrophobic diamond-like-carbon (DLC) tip and the kaolinite faces at pH 4, which is around the isoelectric point of the DLC tip. Under these conditions, the effect of electrostatic interaction should be eliminated and only van der Waals interactions and hydrophobic-hydrophobic interactions are expected to contribute to the surface force. The wettabilities of the surfaces were determined from the magnitude of the surface force. Wettabilities of the kaolinite basal planes thus determined were compared with the corresponding wettabilities of talc and mica surfaces, which are well-known to be naturally hydrophobic, and hydrophilic surfaces, respectively. The results reveal that the silica tetrahedral face of kaolinte has a modest level of hydrophobicity, which may be due to the lack of hydrogen bonding sites. In contrast, the alumina octahedral face showed no hydrophobicity, since a layer of surface hydroxyl groups is present at the alumina face, resulting in a relatively strong interaction between this surface and water molecules. It is expected that, with a better understanding of the surface properties of kaolinite, further improvements in flotation separations and dewatering may be achieved.

Feb 1, 2012

By N. Mizutani, S. Harada, Z. Asaki, T. Tanabe

"The development of lead-free solders is urgent in view of environmental standpoints. In this -work the wettability of tin-bismuth- silver solders on copper was studied. Three kinds of fluxes were used. The wettability of conventional eutectic tin-lead .solder exhibited an excellent level over the other solders of tin-bismuth systems. Poor wettability of the tin-bismuth solders may be caused by the growth or dendritic copper-tin compounds at copper/solder interface, in contrast to the case of tin-lead'· solder. The wettability was improved by the addition· of silver in the solder. In this tin bismuth- silver system, silver was abnormally concentrated at the copper I solder interface even in the initial stage of contact. The wettability of the solder and the thickness of compound formed on the copper have a good correlation; the solder containing 2% silver exhibited the best wettability and the formation rate of copper-tin· compound on the copper was slowest.IntroductionSocial demand to avoid lead use in the industrial fields has been recently promoted· (1) because of the environmental protection of water resources. Especially the lead-bearing solders have been widely used in electronics and automobile products, and it is urgent to replace them with nontoxic materials (2)-(4). Thus the development of lead-free solders becomes an indispensable subject to the new generations and many works (5)(6) have already been carried out on the research and development of new solders. New lead-free solders are expected to have some requirements, for example, moderate melting temperature, proper strength and integrity, and lower prices, as compared with conventional solders. There have been already several alloy systems developed. Among ·these alloy systems, tin-bismuth binary or tin-bismuth-silver ternary alloys have great advantages such as having a wide range of soldering .temperature by controlling con:ipositions, though they have such disadvantages as ""lift-off"" (7)-(9): It is said, on the other hand, that a frequently overlooked property of solders, or one that is typically ignored by the research scientist as an ""issue"" for the manufacturing or product engineer, is wettability (10), although a ·work on the wettability has recently been published (11). In this Work, therefore, the authors selected Sn-Bi-Ag solders and focused mi the effect of Ag-addition to wettability of the solder."

Jan 1, 2000

By McKinnon R. L

Laboratory and field work on the use of wetting agents for suppression of colliery dust is described. Although the results were inconclusive they were not discouraging and further investigation is required. The use of certain wetting agents may constitute a healthhazard.INTRODUCTIONCoal dust presents explosion and health hazards to the coal mining industry. The problem of dust suppression is particularly acute where water alone is unsatisfactory for this purpose. The addition of a surface active agent (wetting agent) to the water should enable the dust particles to be more easily wetted and thus more easily prevented from entering and spreading through the mine atmosphere.Investigations into this effect carried out at The University of Sydney mainly under research grants from The Joint Coal Board (Dawson and Hargraves, 1955; Charlton and Curnow, 1957) are summarized, and information on the possible harmful effects of certain wetting agents is given.Twelve local manufacturers and five importers supplied 52 wetting agents in liquid, solid, powder, and paste form.The active material content varied from approximately 10 per cent to 100 per cent and the cost per pound from 8d. to 14/3.LABORATORY TESTINGPossible test methodsThree methods of laboratory testing were considered.1. The standard method for comparing wetting agents is the Draves test, used in the textile industry on cotton...

Jan 1, 1961

By T Baumgartl, R Akesseh, M Edraki, B Usher, M Shaygan

With the continuing demand for industrialisation and urbanisation, the rate of mining and processing lower grade ores will also increase, producing large quantities of waste. As extreme weather events associated with global climatic changes are to be expected, the risk from mine tailings management will also increase (Edraki et al., 2014). In sulfide rich tailings, weathering within the critical zone controls the fate and distribution of the contaminants such as copper, zinc, and lead in the environment (Hayes et al., 2014). Tailings evolve geochemically and physically with time as they age under the influence of complex interacting factors. Understanding of the complex interactions between these controlling factors is important for predicting and mitigating the potential risks associated with sulfide tailings such as generation of acid mine drainage (Lindsay et al., 2015). Wetting and drying initiates weathering processes, influencing the hydrological, geochemical and geomechanical properties of the tailings. In semi-arid climates where evaporation exceeds precipitation, salts may precipitate within the pore system as well as on the tailings surface. These salts become the temporal sink of heavy metals until the next episodic rainfall (Nordstrom, 2011, Grover et al., 2016). Therefore, using kinetic and static test to describe the trajectory of these material evolutions without considering the complex interactions could potentially lead to erroneous prediction. In order to understand these relations, the effect of drying and wetting cycles on the hydrological, geochemical and geomechanical properties of ageing tailings was studied to draw conclusions for advanced tailings site rehabilitation and mine closureCITATION:Akesseh, R, Shaygan, M, Usher, B, Edraki, M and Baumgartl, T, 2018. Wetting and drying cycles as a means to determine the effect and consequences of tailings ageing, in Proceedings Life-of-Mine 2018, pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By H. Fukuyama

The wetting behavior of single crystalline MgO by fayalite-type slag melts has been studied by the sessile drop technique incorporated with high temperature X-ray radiography. The experiments were performed under oxygen partial pressures of 10-6 and 10-4 Pa at 1473 K. Mass ratios of iron to silica, Fe/Si~, in the slag employed were 1.4 and 2.0. To investigate the interfacial reaction, experiments using high density MgO crucibles were also conducted. The reactions at the interfaces were examined by Electron Probe Microanalysis. The contact angles between the slag melts and the MgO substrates were found to be relatively low, ranging from 30 to 10 degrees. The surface tension of the slag was 0.4 N/m for a slag of Fe/Si02 = 2.0. Two phases, magnesiowiistite and olivine, were observed at the interface. Interdiffusivity in magnesiowiistite solid solution was determined as a function of iron oxide content. Phase relations between magnesiowilstite and olivine, and the growth rates of both phases, are also discussed

Jan 1, 1996

By B. R. Mohal, F. F. Aplan, S. Chander

"ABSTRACTThe wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5 ] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3( CH2 )8-C6H4,- ( OC2H, ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3)2-C6H4- ( OC2H4) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 to determine the effect of surfactants on wettability of cotton fibers. In this procedure commonly known as the Draves test, the concentration of a surfactant required to give a 'sink time' of 25 s is determined.Other investigators have used slight variations of the Walker method to study the wetting of fine particles [ 8-12 ] , by measuring the time for wetting a given amount of powder. There are differences in the manner in which the time of wetting is measured, however. Some investigators measure the time for the last trace of coal to disappear [ 8,11 ] whereas others determine the time for the vast majority of particles to sink [ 10 ] . Some investigators report a wetting rate [ 11 ] which is a value calculated on the basis of the time for the 'last traces of particles to sink'. The differences in choice of criterion for wetting can result in different values for wetting rates as illustrated in Fig. 1 which is based upon our measurements of the amount of powder wetted as a function of time. The procedure for wetting rate measurements is described in the next section. The technique in which time for disappearance of the 'last traces of particles' is determined gives the smallest value for the wetting rate, while the technique in which the time for wetting of the 'vast majority' of particles is determined will give intermediate rates. The terms 'last traces of particles' and 'vast majority of particles' are usually not defined explicitly and can lead to large differences in wetting rates measured by different investigators. Since our measurements show that the wetting rates for an assembly of powder decreases with time, we have used the initial wetting rates to compare the wetting behavior of coal in solutions of different surfactants."

Mar 1, 1989

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3 ( CH2 ) 8-C6H4-( OC2H4 )""' where n is the number of ethoxy groups). The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3 ) 2-C6H4-( OC2H4)"").Initial wetting rates - modified Walker techniqueWalker et al. [ 6] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and, flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series con tains a linear hydrocarbon chain containing nine carbon atoms (CH3 ( CH2 )8-C6H4- ( OC2H4 ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight' carbon atoms ( ( CH3 ) 3CCH2C ( CH3) 2-C6H4- ( OC2H4 ) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determine& This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 ] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By W. H. Jang

Although surface chemistry fundamentals of semi-soluble minerals have been studied by many researchers, detailed understanding of these systems is still incomplete. In-situ FT-IR/IRS techniques have recently been used to successfully describe the adsorption of carboxylates at semi-soluble mineral surfaces. However, the wetting characteristics of these adsorbed films require further consideration. In this regard, the hydrophobicity and stability of transferred Langmuir-Blodgett (LB) monolayers of fatty acids at fluorite and calcite surfaces has been studied by contact angle measurements with polar and apolar liquids. Generally, it was found that the transferred LB monolayers of fatty acids at a calcite surface are unstable whereas such monolayers transferred at a fluorite surface are stable, as revealed from advancing and receding contact angle measurements. These results are believed to be due to the incomplete reaction of fatty acid monolayer at the calcite surface. In addition it was found that a closely packed well-ordered stearate monolayer with good hydrophobicity, equivalent to that of a transferred LB monolayer, can be formed at fluorite surfaces by spontaneous adsorption and self-assembly from aqueous solutions.

Jan 1, 1995

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

By B. R. Mohal, F. F. Aplan, S. Chander

"Dust abatement by water sprays involves the subprocesses of 1) collision between dust particles and water droplets, 2) adhesion of particles to droplets, and 3) engulfment of particles by the droplets. A review of the fundamental aspects of these subprocesses shows that collisions between particles and droplets are determined by aerodynamics and the size and surface charge of the particles and of the droplets. However, the adhesion and engulfment subprocesses depend upon the wetting characteristics of the particles. Although wetting agents (also known as surfactants) have been used as dust suppressants in several investigations, conflicting results are available regarding their effectiveness. In this paper, we show that these results can be explained if the effects of coal rank on surfactant adsorption and wetting characteristics are taken into account.The influence of several nonionic surfactants containing polyethoxy adducts on the wetting behavior of coal is presented. The wetting was determined by a modified Walker Test method, and contact angle measurements. The results show that the wettability of coal depends upon coal rank, structure of the hydrocarbon chain of the surfactant, and the number of ethoxy groups in the molecule.IntroductionDue to the inherent nature of the mining process, a large number of particles are generated, a portion of which becomes airborne to create dust. Dust can be aesthetically and environmentally unacceptable and it can also be explosive. Fine particles in the respirable size range ( < 5 urn) are con-sidered to cause lung diseases, namely, silicosis, pneumoconiosis, etc.(1) Several approaches to reduce dust in mine environments are practiced throughout the mining industry. These include decrease in generation of dust through improvements in mine machinery, ventilation (in which lower dust levels are achieved by dilution of contaminated air with clean air), and dust removal methods. Water sprays are most commonly used to remove dust par-ticles. Recently, scrubbers are reported to have been installed on mining machines to remove dust,(2,3) which also make use of water sprays to reduce dust."

Mar 1, 1989

By Lei Pan, Roe-Hoan Yoon

"Sea water flotation is becoming a reality due to shortages of fresh water. To better understand the mechanisms involved in sea water flotation, we have studied the effects of KCl and MgCl2 on the surface forces present in the wetting films of water formed on hydrophobic surfaces. The measurements have been conducted using the force apparatus for deformable surface (FADS), which is capable of measuring both the surface and hydrodynamic forces responsible for bubble-particle interactions. The results obtained with the gold surfaces hydrophobized with butanethiol (C4SH) show that the wetting films of Ultrapure water do not rupture despite the relatively high water contact angle (??= 80o) and the presence of a long-range hydrophobic force with a decay length (D) of 25 nm in the film. The film is metastable with its equilibrium thickness (he) at 140 nm, where the repulsive double-layer force is equal in magnitude to the capillary force as shown in Figure 1. The film loses its metastability and ruptures in a 10-2 M KCl solution, in which the double-layer force decreases substantially due to the decrease in Debye length (?-1) while the decay length of the hydrophobic force remains as large as 23 nm.The effects of MgCl2 has also been studied using a C4SH-coated gold surface with a water contact angle of 87o. It has been found that in a 10-4 M solution double-layer force decreases due to the decrease in the negative ?-potentials and Debye length, which should help destabilize the wetting film. However, the film remains stable due to the decrease in the decay length of the long-range hydrophobic force from 45 nm in Ultrapure water to 14 nm in the MgCl2 solution. Thus, the results obtained in the present investigation support the view that the difficulties in sea water flotation may be due to the presence of MgCl2 rather than the presence of NaCl in sea water (Ramos, et al., 2013)."

Jan 1, 2016

Water contact angles in the air/water/francolite, fuel oil/water/francolite and fuel oil/water/quartz systems were measured to describe the wetting characteristics of these minerals. It was found that white francolite is more hydrophilic than black and tan francolite both in the absence and presence of fatty acid addition. The contact angle measurement results do not correlate very well with the flotation response and it appears that kinetic aspects of the bubble attachment process play an important role in the francolite-fatty acid flotation system.

Jan 1, 1997

By Y. Kocaefe, D. Kocaefe, G. Ergin

Filtration efficiency depends strongly on the wetting of the bed media by aluminum. This project was undertaken to study the wettability of different types of bed media (tabular alumina) using sessile-drop and infiltration techniques. The samples were analyzed using optical microscopy, SEM, and TEM to study the chemical interactions. The results indicate the spinel formation at the interface. This paper presents some of the findings which compares the two methods and gives the results of the analyses on the wetting of alumina by aluminum.

Jan 1, 2004

By J. Drelich

The highly-efficient and economically-feasible technology for bitumen recovery from US oil sands using a water extraction approach was developed at the end of the last century. This water-based bitumen extraction process has been optimized based on observations and analysis of microscopic mechanisms of bitumen release from oil sands and the bitumen transfer to a froth product as well as measurements of interfacial properties of bitumen. The wetting mechanisms that occur in the diluent-assisted water-based processing of US oil sands include bitumen film rupture and recession on sand grains and bitumen transfer to nucleated and injected gas bubbles. These mechanisms are reviewed in this contribution.

Jan 1, 2007

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By Yves Caron

Résumédes travaux effectués De septembre 2009 àmai 2011 ? Plus de 21 000 m de forages complétés en avril 2011 et près de 9 000 échantillons ? 2,7 km de décapage, 52 tranchées et 852 m de rainures ? Estiméde ressources 28 mai 2010 (SGS Géostat) ? Essais métallurgiques en laboratoire (automne 2010) ? Étude économique préliminaire (janvier 2011)

May 1, 2011