Search Documents

By Michael Amick

Due to the importance of maintaining open airways on a longwall panel, mine management decided to install cribs made of foamed cement. Foamed cement had been used at other company operations on several projects. A recent test at a sister operation had proven the crib installation technique and established that foamed cement cribs could provide better support than wooden cribs. The area to be supported was in a remote location; the limited material needs of foamed cement cribs offered a substantial advantage. In mid February 1993, 75 foamed cement cribs were installed on the tailgate of the active longwall panel. The 75 cribs resisted both horizontal and vertical stresses while successfully supporting the entry.

Jan 1, 1993

By D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, increasingly are becoming important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance techniques and correlated to flotation response. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for 1?) d at 65? C inhibited flotation of chalcocite, and chalcopyrite even after the addition of a large amount (1 x 10') M) of collector. Heavily oxidized (27 d) chalcocite remained unfloatable. However, longer oxidation of pyrite and chalcopyrite restored the floatability. Oxidation resulted in an electrically resistive, nonporous surface layer.

Jan 1, 1993

By Z. Kokesz

The following paper presents the results of geostatistical studies of the selected hard-coal deposits in Poland. Geostatistical methods were applied mainly to the characterization of variability structure of the coal seams thicknesses as well as sulphur and ash contents in the coals. Results imply that the accuracy of coal reserves estimations can be improved if kriging method is applied. Kriging allows predicting more precisely the values of such parameters as thickness and sulphuring content.

Jan 1, 1993

By Matthew N. Plis

This U.S. Bureau of Mines report presents the documentation for COALVAL, a coal property evaluation software package developed on Lotus 1-2-3,4 version 2.2, spreadsheets. The software is compatible with version 3.1 as well, and may provisionally be run on the earlier 2.01 version. COALVAL is a menu-driven program that produces a prefeasibility-level cost analysis of mine-planned coal resources. The package contains cost models for each of five coal mining methods commonly employed in Appalachia: auger, contour strip, mountain top removal, continuous miner, and longwall. Other models, such as a dragline cost model, will be incorporated as the Bureau's Coal Recoverability Program matures. COALVAL allows mine operators, evaluators, consultants, and Government entities to input resource data and the various production, operating, and cost variables that pertain to their property. The program can evaluate up to 25 seams, each to be mined with up to five different mining methods, within a given area. Summary spreadsheets listing the cost per clean ton to mine the resources, f.o.b. the tipple, are produced for each property, seam, and mining method/seam combination.

Jan 1, 1993

By Sterns UJ, Weller KR

Grinding to sizes less than 80 per cent passing 20 ¦m in both primary and regrind circuits is becoming increasingly important in processing metalliferous ores, as many of the remaining orebodies are very fine-grained and refractory. The process of very fine grinding, however, is expensive, and neither the performance nor the design criteria are well understood. This paper presents some findings from a collaborative research program, one of the objectives of which has been to better understand and improve the performance of very fine grinding circuits. Data from surveys of an industrial tower mill grinding circuit are reviewed and analysed using the population balance models of the CS]RO and 7KMRC. The performance of both models with regard to changes in feed size distribution, ball load and feedrate is assessed using these data. From comparisons between pilot and full scale tower mill operation a prototype scaling methodology is also presented which shows promise in allowing the models to be used to predict the effect of changes in mill Design.

Jan 1, 1993

By Erik C. Westman

The objective of this Bureau of Mines study is to determine the structural integrity and stress state of coal structure using seismic techniques. Bureau personnel conducted seismic transmission and refraction surveys on yield pillars and seismic tomography on rigid pillars. The pillars studied were in the headgate at increasing distances from the working face of a longwall coal mine, effectively evaluating pillars at lowering stress states and increasing levels of structural integrity. By examining characteristics of the seismic wave, including velocity and frequency, the survey results are used to infer yield zone thickness, core mss state, and stress distribution. An accurate definition of these parameters can not only provide mine engineers a useful tool for evaluating mine design, but also give valuable insight into the inherent safety of the mine structure.

Jan 1, 1993

By Hunter W. H, Wilson I. P, Craig R. W

In September 1988 the Imperial Smelting zinc - lead blast furnace at Avonmouth England, was uprated from its then 52 week annual rated capacity of 90 000 tonnes/year of furnace zinc to 110 000 tonnes. In order to provide sufficient extra feed the sinter plant was likewise uprated in April 1989 by increasing the blowing rate of the sinter/acid plants from 100 000 to 120 000 Nm3/h, effectively a 20 per cent increase. In the 12 months after the uprate zinc production was only 85 000 tonnes. Two years after the uprate zinc production had increased to 100 000 tonnes, but it was not until January 1992 that a rolling 12-month zinc production of 110 000 tonnes was consistently achieved. This paper describes the problems encountered with the uprate and how they have been or are being overcome. It deals chronologically with events starting with the restart of the ISF at the end of 1988 and covers the following issues and their resolution: 1. Initial shortages of sinter due to an offset in uprate timing. 2. Greater difficulties in operating the larger furnace particularly on start-up, the greater tendency for iron production and serious slagging problems. 3. Coincidental timing of deleterious trends in slag chemistry. 4. Refractory problems in the furnace shaft and condenser. 5. Shortages of sinter due to commissioning problems with the wet gas and sinter tip end fans, and difficulties in obtaining sufficient sinter hardness. 6. Unrealised full benefits of the sinter-acid uprate due to a late change in design to dispense with sinter gas recirculation, but offset by successful use of oxygen. In a planned maintenance stop in September 1992 further improvements to the furnace design were carried out to resolve the refractory problems, and with improvements to the sinter plant the furnace zinc output capacity is planned to rise to a rate of 120 000 tonnes/year within two years.

Jan 1, 1993

By Chen J, Sun ZY

The present paper gives the design of a new HGMS for magnetic separation of sulphides. The main characteristics of this HGMS are using iron-cladding saddle-shaped magnetic coil for instead of the ordinary magnet, and combining reciprocal-linear motion with vibration to actuate the separation box, and the magnetic field intensity is high up to 2T as well. For improving the magnet system design, a modified finite element method is used to calculate the distribution of magnetic field intensity of separation space of the magnetic coil, and accordingly the calculation results the magnetic leakage coefficient can be determined easily, thus designers apart from the empirical way. KEYWORDS: HGMS, reciprocal motion and vibration, finte element method, saddle-shaped coil.

Jan 1, 1993

By Somasundaran P

Controlled modification of mineral/liquid interfacial properties by adsorption is critical for mineral processing operations such as flotation, filtration, dispersion and flocculation. Ionic/nonionic surfactant mixtures usually show enhanced surface activity and salt tolerance over ionic surfactants, and this is especially beneficial for flotation of salt type minerals in which case dissolved multivalent cations in high concentrations usually cause loss of anionic surfactants by precipitation. Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied with sodium dodecylsulfate as the anionic surfactant and octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactants was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in flotability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also' for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant species at the interface. Also, based on the results obtained with surfactant adsorption, a hydrophobically modified polymer was used successfully to disperse graphite particles in aqueous solution.

Jan 1, 1993

By Joanne L. Johnston

Researchers at the U.S. Bureau of Mines have developed a new technique for bonding strain gauges to rock bolts. These instrumented bolts are used to determine load at intervals along the length of the bolt so that reliable, consistent measurements for the design of support systems can be obtained. In this Information Circular, this technique is described in detail and should result in improved miner safety in underground mines.

Jan 1, 1993

By Jeong-Heum Kim, Jan M. Mutmansky

A number of solution methods for solving the nonlinear equations derived from mine ventilation networks use meshes selected from the network as the basis of the solution techniques. Mathematicians working in network theory have outlined several methods for speeding up the computations through mesh selection and ordering procedures. In the mine ventilation area, a fair amount of attention has been paid by ventilation specialists to procedures for choosing the meshes so that the computational effort is eased. However, little attention has been paid to mesh ordering methods. This paper outlines research into random mesh ordering procedures plus two non-random mesh ordering procedures and compares some results using these procedures within four solution algorithms.

Jan 1, 1993

It is people, not organisations, that make countries great, so it seems appropriate in this Centenary year of The Australasian Institute of Mining and Metallurgy to highlight some of the mining personalities who have contributed to the greatest and most important of Australia's export industries, the Resource Industry.

Jan 1, 1993

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993

By Hui Chen

The paper describes the use of a physical model technique to investigate the failure modes of mine tunnels with reference to the in situ stress field. The characteristics of stratification commonly encountered within UK coal mining conditions have been taken into consideration. The investigation has indicated that the weak floor strata in coal mining tunnels, under the action of high rock stresses, will be subject to the floor lift problem in both predominantly horizontal and vertical stress fields. However, the failure mode and mechanism varies between the two stress field patterns. In the predominantly horizontal stress field, the tunnel floor tends to fail by gradual bending of the laminations, whilst in the predominantly vertical stress field, the floor tends to fail by a shearing action with the failed material lifting in the form of a block. The failure mechanism is discussed with reference to mechanics theory.

Jan 1, 1993

By Brian Hester

Many Third World African countries are well-endowed with minerals - especially gold and diamonds - while only a few have important base metal deposits. For decades since colonial rule, political and economic conditions discouraged interest by Western capital. Influence from Soviet Bloc countries, however, has declined with the move toward multi-party rule. And the left wing orientation, once widely favored by Third World African countries, has almost disappeared. With International Monetary Fund (IMF) encouragement, these Third World African countries now encourage representational government and solicit western finance to expand their industries. Mining is especially encouraged. The North American mining industry is following the same trail as other capital intensive industries and looking abroad for opportunities. The Prospectors and Developers Association of Canada released figures that show exploration expenditures in that country were halved between 1987 and 1990. Figures for the United States are not so easily found but every indication points to a downward trend. While total annual expenditures on US exploration by corporations as a group are either declining or remaining constant, expenditures away from North America is increasing. Gold exploration expenditures in 1991 by the major companies tracked by Minerals Economics Group were less in the United States than for Latin America and the Southwest Pacific combined. The same study showed as much was spent in the Republic of South Africa and "Other" areas combined as in the United States. Expenditures by major corporations in these "Other" areas amount to only 5.2% of their total budget. Third World Africa is a major component of these "Other" areas.

Jan 1, 1993

By Charles L. Kimbell

The estimated value of world crude mineral production in 1990 exceeded $1,501.5 billion in terms of current (1990) dollars, or almost $1,160 billion in terms of constant 1983 dollars. This latter figure was 0.3% below the 1989 level and about 3.9% below the record high to date of $1,207.1 billion 1983 dollars set in 1980. Table 1 provides the latest available revised time series of the estimated value of world crude mineral production both in terms of 1983 constant dollars and in terms of current dollars. It also provides one of the two statistical bases for this estimation, this being the data on the value of production of a group of key commodities that was compiled for and published in the authoritative French language mineral industry periodical, Annales des Mines, for selected years up to 1983.1 It should be stressed that the values just discussed and those presented in the tabulation are for crude minerals only, and by no means reflect adequately the role of the entire mineral industry in the world economy. These figures represent only the value of mineral materials as they are mined or otherwise extracted from the earth. They do not reflect the value added to these materials through downstream processing within the facilities commonly accepted as mineral industry plants. That is, value added through beneficiation of ores, smelting, refining, and similar processing is not included in these figures. Comprehensive world data on the value added by such processing are not available; however, a conservative estimate of the total value of pro-cessed output from mineral industry plants derived wholly from primary (newly mined) materials would be on the order of about $2,780 billion constant 1983 dollars or $3,600 billion in terms of 1990 dollars.

Jan 1, 1993

By Margaret E. Egan

Reliable fire detection is essential for both safe evacuation and containment or extinguishment. In order to increase reliability by reducing the number of nuisance fire alarms in underground mines that use diesel-powered equipment, the U.S. Bureau of Mines has developed a diesel-discriminating fire detector (DDD). It was designed to discriminate between smoke produced by a fire and the smoke-laden exhaust of a diesel engine. Experiments were conducted by the Bureau to compare the smoke detection capabilities of the DDD with those of conventional fire detectors in response to smoldering coal and conveyor belting. A comparison was made among the alarm times of a carbon monoxide (CO) detector with an alarm threshold of 5 ppm, a smoke detector with an optical density alarm threshold of 0.044 of', and the DDD with an alarm threshold of 0.025 V. The results show that the DDD will reliably detect developing coal and conveyor belt fires. The average time delay separating the DDD alarm from the first detector to alarm was 76 s for smoldering conveyor belt and 65 s for smoldering coal. The longest time delay between the response of the DDD and the first detector to alarm was approximately 120 s.

Jan 1, 1993

By W. C. Lacy

Traditionally Australia has been a leader in underground mining methods with world standards being established at Mount Isa, Broken Hill, Kalgoorlie, and Mount Lyell. With decline in higher-grade reserves and discovery of a multitude of near-surface oxide gold de-posits attention has shifted to bulk mining of low-grade gold ores by open pit methods, heap leaching and activated carbon recovery of gold values. The paper examines historical change in mining philosophy and the economic effects of isolation.

Jan 1, 1993

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993