Search Documents

By S. Pignolet-Brandom, E. Fregeau-Wu, I. Iwasaki

To recycle steelmaking slags for their iron, manganese and lime contents, removal of the phosphorus-bearing dicalcium silicate and calcium phosphate is essential. Slow-cooling of slags was necessary to promote sufficient grain growth to achieve liberation. In situ grain size distribution determination showed that a high soaking temperature, a long soaking time, a very slow cooling rate and the addition of fluorspar promoted grain growth. High gradient magnetic separation on slow-cooled slags removed much of the dicalcium silicate. Liberation modeling was used to discuss the breakage and beneficiation characteristics of the slow-cooled slags.

Jan 1, 1993

By Mankosa MJ, Yoon R-H

A reliable scale-up procedure for column flotation must address three important areas of column design, ie column geometry, sparging system and wash water distribution network. The column geometry is dictated by the maximum froth carrying capacity (which determines column diameter) and the bubble-particle attachment rate and particle retention time (which determines column length). The most important factor in the scale-up of an air sparging system is the ability to produce small bubbles in both laboratory and full-scale columns. Other factors, such as energy consumption and maintenance requirements, should also be considered in the scale-up of bubble generators. It is also important to design a wash water distribution system that can properly control the froth stability and maximise the column throughput. Based on these criteria, a successful scale-up example is given.

Jan 1, 1993

By R. Hogg, P. Bunnaul

Sedimentation in highly, flocculated suspensions of fine particles, such as clays, occurs through individual settling units (flocs) that have very open structures and correspondingly low densities (typically less than 5% solids by volume). Such settling processes rapidly lead to the buildup of a bed of flocs that are essentially close-packed, with an inter-floc porosity of perhaps 50%. However, the overall solids content is no more than about 2% to 3% by volume. Consequently, the thickening process is dominated by the bed consolidation rather than by the simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate, for a given system, that consolidation rates are essentially determined by the solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical, as well as the chemical, conditions of the flocculation process. Furthermore, the extent to which gravity consolidation proceeds depends on the total weight of the sediment (i.e., on the bed height and the solids concentration). The implications with respect to thickener operation and the requirements for the laboratory testing for thickener design are discussed.

Jan 1, 1993

Room-and-pillar mining at White Pine started in 1953 from a sub-outcropping orebody that gently dips to 1000 m depths in a distance of about 6 km. High horizontal stresses were recognized in the mid-1960s which had obvious stability impacts when viewed in combination with the increased overburden stresses. Modifications in conventional room-and-pillar design were introduced through the years on a trial-and-error basis to help overcome stability and resource recovery problems. These modifications were based on pressure arch concepts using pillar yielding and/or pillar recovery, and on mine layout orientation to minimize stress impacts. While some of these modifications were successfully applied in some areas, they failed in others. Through the years, visual observations played a major role in panel design with contributions from stress measurements and analyses. However, the down slide in the copper economy during the 1970s and early 1980s resulted in a loss of interest in the application of these concepts. This paper reviews ground control problems and presents the results of recent stress measurements and computer analyses. They shed light on the importance of using yield pillars and mine layout orientation to control stresses at depth.

Jan 1, 1993

By Robert B. Hopler

Explosives research and development has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. Today, this process continues at an accelerated pace due to the tools presently available to the explosives and mining industries. Background Explosives have been used in coal mining since the industry's earliest days. Black powder, introduced into metal mining in 1627, undoubtedly was introduced into coal as soon as a need to replace pick work was apparent. Until the invention of the safety fuse by William Bickford in 1832, the only initiation methods available were the straw, quill and miner's squib. Disastrous explosions underground in England brought about studies on their possible causes (Atkinson, 1886). The studies showed that, while explosives contributed to the accidents, the real villain was coal dust, since that was the agent that transmitted the disaster throughout the mine workings. To improve underground safety, research was applied in an attempt to make explosives that could be safely fired in a methane air atmosphere. The Prussian government was apparently the first to establish a testing station for coal mine explosives. This occurred in 1885 (Guttmann, 1909).

Jan 1, 1993

It is a great privilege to be invited to give this address at this centenary conference. A centenary is a time for recollection, for celebration and for looking ahead. The AusIMM has much to celebrate and many things to recall. I hope in this address to make some useful comments about Australia's future (and mindful of but not forgetting New Zealand), looking ahead for 25 years or so, and the mining industry's role in that future.

Jan 1, 1993

By Andrea B. Baldwin

Solvay Minerals, Inc. (formerly Tenneco Minerals Company) is one of five producers who use trona to produce soda ash at Green River, Wyoming. Over the years, many producers, including Solvay Minerals, extended their product lines by manufacturing other sodium products based on trona. This paper focuses on the criteria used by Solvay Minerals in the selection of new products added at its Green River, WY operations. An example is given in the selection of caustic soda production.

Jan 1, 1993

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By K. Musgrave, E. Solis

"This paper tells the story of how the Dome Mine in South Porcupine increased its maintenance effectiveness and reduced its maintenance costs in two phases. In the first phase, a maintenance audit was conducted, and the results led to some changes that improved maintenance, especially in the underground equipment area. The audit methods, and the changes made will be reviewed. In the second phase, management made changes in the maintenance organization and methods, following a prolonged strike during which management operated the mine. These changes were in part the result of insights learned from their hands-on operating experience. IntroductionEarly in 1989 the Dome Mine of Placer Dome Inc. in South Porcupine, Ontario, decided to improve the effectiveness of the Plant Department. The Plant Department was centralized, except for a mill mechanical crew, and serviced all operations, a townsite of 120 houses, a curling rink, and an arena. The department also operated the powerhouse, the hoists, the mine dry and provided mechanical/ electrical engineer services.At that time the Dome Mine, located in the east end of the city of Timmins and Canada's first large gold mine originally discovered in 1909, was producing about 3500 tons of ore per day with about 742 employees. Over the 83 years of continuous operation of Dome over 50 million short tons of gold ore have been processed. The Plant Department consisted of 156 hourly and 24 staff employees. At present, the mine is producing 4000 tons of ore per day with a total of 341 employees on the payroll. The Plant Department consists of 80 hourly-rated and 18 staff employees."

Jan 1, 1993

By Lawrence K. Nordell

Historical methods of designing steel cord belt splices are compared with modern finite element modeling (FEM) methods. Dependence of the belt strength rating on the splice dynamic fatigue strengths is reviewed. A number of splice schematics are examined, using simple spring theory and FEM methods. Steel cord wire rope design is discussed. The importance of the insulation gum rubber properties and their splice dimensional factors and tolerances are analyzed. Splice fatigue lie analysis procedure is reviewed. This may be used to predict splice life or time of failure, depending on how the conveyor belt is operated.

Jan 1, 1993

Experience in evaluating grade control at operating mines has shown that a number of similar errors re-occur in diverse settings. These can be broadly classed as technical errors, and procedural or grade contra management errors. Examples of typical errors are presented a; generalised case studies. A brief explanation of why the recommender solution worked is also presented for each case.

Jan 1, 1993

By Mingmin Dou

The behaviour and deportment of indium during the precipitation of sodium jarosite from Fe2(S04)3 - Na2SO4 solutions were investigated. Indium is readily precipitated with sodium jarosite, and the extent of In precipitation increases as the In concentration of the solution increases. It was shown that In 3+ substitutes for Fe 3+ in the jarosite structure to form a nearly ideal solid solution series. On a molar basis, the precipitation of Fe is slightly favoured over that of In, and the difference is reduced as the pH increases. Sodium jarosite precipitation becomes kinetically rapid at temperatures >70¦C, but increasing temperatures in the range 70 to 150¦C affect neither the relative precipitation of In and Fe nor the composition of the jarosite product. Low Na2SO4 concentrations result in reduced product yields and jarosite precipitates in which H3O' > Na+. The hydronium-rich precipitates have reduced In contents. Increasing the ZnSO4 concentration of the solution slightly increases the quantity of jarosite formed and results in the incorporation of -0.3 per cent Zn in the jarosite structure. Otherwise, the presence of ZnSO4 has no significant effect on the composition of the jarosite. Seeding accelerates the rate of jarosite precipitation but has a negligible influence on the deportment of In. The jarosite precipitation reaction at 98¦C is relatively rapid and near-steady state conditions are achieved in - 6 h even in the absence of seed. The initially precipitated jarosite is slightly enriched in In with respect to Fe. The ferric ion concentration of the solution has a significant influence on both the amount of jarosite formed and its composition. In particular, the jarosites precipitated from dilute Fe3+ media have significantly enhanced In contents. Hence, it may be possible to recover - 25 per cent of the dissolved In, at the 1000 mg/L level, in a jarosite precipitate assaying - ten per cent In by the controlled oxidation-precipitation of sodium jarosite from a ferrous sulphate processing solution.

Jan 1, 1993

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By Rashkovski GB

Until recently amalgamation has been the main process forextracting large gold particles from gravity concentrates obtainedduring the dressing of ores and placer gold deposits.Development of new technology for treating the gravityconcentrates was necessary because of the harmful effect ofmercury on subsequent production processes and theenvironment. The harmful effect of mercury is particularlyevident in the resin-in-pulp process that is widely applied inRussia.

Jan 1, 1993

By J. E. Murphy, R. Y. Wan, K. R. Sandgren, M. C. Fuerstenau

As part of a U.S. Bureau of Mines program to evaluate alternatives to sodium cyanide in gold leaching, three organic nitrile compounds were tested for their effectiveness as gold lixiviante. The organic compounds examined were malononitrile, acetonitrile, and cyanoacetamide. The reagents were tested on an oxide ore, two carbonaceous ores, and a eulfidic ore. Acetonitrile and cyanoacetamide were shown to be ineffective gold leachante. Malononitrile was the most successful of the organic lixiviants. On an oxide ore, malononitrile performed shilarlyto sodium cyanide with extractions of around 80 pct. For carbonaceous "preg-robbing" oree, sodium cyanide was completely ineffective while malononitrile extracted 24 pct of the gold. When using a resin-in-leach technique, extraction with sodium cyanide increased to 60 pct and the extraction with malononitrile increased to 80 pct. On the sulfide ore, sodium cyanide and malononitrile performed similarly with 80+ pct extraction as long as the pH of the malononitrile solution wae maintained above 10.5. Malononitrile is six times less toxic than sodium cyanide as measured by LD, levels. Therefore, malononitrile has a significant advantage over eodium cyanide, but its high cost and undemonstrated usefulnees make it unlikely to gain acceptance.

Jan 1, 1993

By R. F. Favreau

"After a blast, the volume of the blasted rock normally occupies more space that it did before the explosion. The degree of such swell significantly affects the efficiency of digging the muck with a shovel or dragline. This paper explains why swell occurs, and describes the new subroutine SWELL of the blast simulator BLASP A which can simulate blast-induced swell. Results are also presented which display the effect of various blasting parameters on the degree and distribution of the swell within the muck pile of a bench blast. IntroductionIt is a common opinion that fragmentation is the most important of the various aspects which affect the efficiency of excavating rock with explosives. This paper proposes that, in fact, displacement and swell of the blasted rock are as important as fragmentation if the excavation process is to be rapid and efficient. It must ""a priori"" be recognized that a minimum degree of fragmentation is indeed necessary. For a given shovel or dragline, this minimum degree of fragmentation may be defined as follows: even the largest fragment of rock must be easily contained within the bucket. Once this criterion is met, however, there are good reasons to believe that displacement and swell take over as the key criteria which influence the rate of mucking, in cubic metres/hour. If the muck pile is not well displaced and swelled, the teeth of the bucket have difficulty penetrating between the rock fragments even if fragmentation is good and, as a result, the mucking is slow and inefficient. The purpose of this paper is to use computer simulations on the model BLASP A to demonstrate the effect of the blast design parameters on the displacement and swell of the blasted rock."

Jan 1, 1993

By R. G. Reddy

The effect of solid particles on viscosity behavior of Na2O-O-B2O3-SiO2 melts of composition XSio2/XNa2o =0.5 and in the temperature range of 900- 1150 K was studied. Samples were analyzed by X-ray diffraction and optical microscopy. The results showed that a crystalline phase (NaBO2) was formed and its amount increases with decrease in X,, from 0.50 to 0.25. The experimental viscosity values were compared with the predicted values using our viscosity model developed earlier. At low temperatures, for low content of B2O3 , the experimental values exhibits a large deviation from the predicted values. It was concluded that the deviation was due to the formation of solid particles in the molten slags. The existence of these solid particles increased the viscosity values significantly. A new viscosity model was developed to include the effect of solid particles.

Jan 1, 1993

By Catharine T. Fogg

The U.S. Bureau of Mines investigated the availability of platinum, palladium, and rhodium from 16 deposits in four market economy countries (MEC's). Major recoverable products include 164 Moz of platinum, 80 Moz of palladium, 13 Moz of rhodium, 24 Moz of ruthenium, 4 Moz of Iridium, 2 Moz of Osmium, and 10 Moz of gold. The 12 deposits in the Republic of South Africa are estimated to account for 96.7 pct of total recoverable platinum. The base-case scenario estimates the long-term cost of production including recovery of capital, but provides no return on the investment or O-pct discounted cash-flow rate of return (DCFROR). The total production costs in January 1990 U.S. dollars ranged from $325/oz to $1,288/oz of platinum compared to an average January 1990 price of $492/oz. Approximately 83 pct of total recoverable platinum was economic at a cost level of $4S0/oz or less. At the IS-pct DCFROR, only 26 pct of total recoverable platinum was economic. For platinum-group metals (PGM), attention has been focused on the ratios of the three primary metals: platinum, palladium, and rhodium. Sensitivity analyses were performed to determine the impact long-term rhodium price increases could have on the total cost of production for platinum and palladium.

Jan 1, 1993

By Saurabh Rastogi, Vikram Shishodia, B. Pitchumani

Comminution is a unit operation which consumes major part of energy in mineral processing industries such as fertilizer production. Ball mills are widely used for size reduction of a given ore to the liberation size that is required in further beneficiation processes. In grinding of materials much effort is concentrated on control of top size of the product and this results in production of fines, also creates secondary problems of pollution due to the difficulty in the collection of fine particles. The present work has been carried out to control product size distribution for rock phosphate grinding in an Industrial Ball Mill of 600 TPD. The plant data are taken for a given feed distribution and mill operating conditions. The information at various Ball Size distributions are collected. The comminution functions such as specific rate of breakage and breakage distribution functions are estimated by back calculation technique to solve the mass balance equation. A simulation program is written to study the product size distribution obtained for various ball size distribution.

Jan 1, 1993

By S. C. Suboleski, R. Zhao

A Simulation/Animation Model (SAM) with several unique features has been developed for continuous mining in room-and-pillar production systems. Initial cut data are generated by the program based on a short list of general section parameters, and is graphically displayed on the screen for checking and editing. This portion of the program includes several intelligent features. For example, a different cut sequence will be generated for uni-directional section ventilation than for bi-directional flow. Once the data are accepted, the entire simulation may be viewed in animation. Effectively, much of the data are checked visually by watching the actions of the mining equipment. Following the simulation, results are summarized as bar and pie charts, as well as printed output. In addition to the extensive use of graphics, the program contains several advances in simulation techniques as well.

Jan 1, 1993